207e32a9f2
1. undefine led_classdev_register as it is defined in leds.h 2. header file location change a. linux/i2c/pmbus.h -> linux/pmbus.h b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h |
||
|---|---|---|
| .. | ||
| modules | ||
| service | ||
| utils | ||
| README.md | ||
README.md
Ingrasys S9200-64X Platform Driver for SONiC
Copyright (C) 2016 Ingrasys, Inc.
This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.
Licensing terms
The Licensing terms of the files within this project is split 2 parts. The Linux kernel is released under the GNU General Public License version 2. All other code is released under the GNU General Public License version 3. Please see the LICENSE file for copies of both licenses.
Contents of this package
- service/
Service config files for platform initialization and monitoring
- utils/
Scripts useful during platform bringup and sysfs function
- conf/
Platform configure files.
Kernel modules and drivers
The driver for interacting with Ingrasys S9200-64X is contained in the I2C kernel module and initialization script. The initialization script loads the modules in the correct order. It has been built and tested against the Linux 3.16 kernel.
The initialization script will modprobe the needed modules, navigate to the module's device directory in sysfs, and write configuration data to the kernel module.
IGB
This is OOB Ports on front panel for management plane.
The IGB module must be loaded first on Ingrasys S9200-64X platform.
I2C i801
The I2C i801 on Ingrasys S9200-64X can be found in
/sys/bus/i2c/devices/i2c-0/
This is I2C bus for Clock Gen, DIMM channel and digital potentiometers.
The i801 module must be loaded second on Ingrasys S9200-64X.
I2C iSMT
The I2C iSMT module on S9200-64X can be found in
/sys/bus/i2c/devices/i2c-1/
This is I2C bus for CPLD, HWM, power controller and I2C Switches.
The i801 module must be loaded third on Ingrasys S9200-64X.
I2C PCA9548
The PCA9548 module on S9200-64X can be found in
/sys/bus/i2c/devices/i2c-2/ , /sys/bus/i2c/devices/i2c-3/,
/sys/bus/i2c/devices/i2c-4/, /sys/bus/i2c/devices/i2c-5/,
/sys/bus/i2c/devices/i2c-6/, /sys/bus/i2c/devices/i2c-7/,
/sys/bus/i2c/devices/i2c-8/, /sys/bus/i2c/devices/i2c-9/.
The pca9548 module for zQSFP module get/set functions, PSU information, fan status and EEPROM.
Hardware components
The hardware components are initialized in the init script on S9200-64X. The following describes manual initialization as well as interaction. The examples below are just for Ingrasys S9200-64X platform.
Hardware initialization
When the sonic-platform-ingrasys-s9200-64x package is installed on the S9200-64X, it is automatically initialized. If you want to manual initialization, the utility command usage as follows:
i2c_utils.sh i2c_init
EEPROM
The EEPROM is including the board SKU, model name, vendor name, serial number,
and other information can be accessed with the specific eeprom kernel module.
After using modprobe eeprom_mb to detect the eeprom, it will show up in sysfs.
The hexdump utility can be used to decode the raw output of the EEPROM. For example,
bash# echo "mb_eeprom 0x54" > /sys/bus/i2c/devices/i2c-9/new_device
bash# cat /sys/bus/i2c/drivers/mb_eeprom/9-0054/eeprom | hexdump -C
Front panel LEDs
LEDs can be setup on/off by using i2c utility /usr/sbin/i2c_utils.sh.
Utility function command usage as follows:
Status LED:
i2c_utils.sh i2c_sys_led green|amber
Fan status LED:
i2c_utils.sh i2c_fan_led green|amber
PSU1 status LED:
i2c_utils.sh i2c_psu1_led green|amber
PSU2 status LED:
i2c_utils.sh i2c_psu2_led green|amber
QSFP Module Port LEDs control by ASIC library.
Fan speed
Fan speed are controlled by the w83795 kernel module.
It can be found in /sys/class/hwmon/hwmon5/device/.
If they were compiled as modules, you will need to modprobe w83795 for
their sysfs entries to show up. Each fan has an fan<N>_input file
for reading the fan speed. And pwm2 setting fan1/fan3/fan5/fan7.
There is docker-platform-monitor container installed fancontrol package that can automatic control platform fan speed.
Temperature sensors
Temperature sensors are controlled by the w83795 kernel
module. It can be found in /sys/class/hwmon/hwmon5/device/.
If they were compiled as modules, then you will need to modprobe w83795 for
their sysfs entries to show up.
temp1_input is front MAC temperature sensor. temp2_input is rear MAC
temperature sensor.
There is docker-platform-monitor container installed lm-sensors package that can
monitor platform temperature. And sensors command can show each
temperature sensors status.
Power supplies
Power supplies status and its EEPROM info can be used i2c utility
/usr/sbin/i2c_utils.sh to get.
The usage as follows:
PSU EEPROM:
i2c_utils.sh i2c_psu_eeprom_get
hexdump -C psu0.rom
hexdump -C psu1.rom
PSU Status:
i2c_utils.sh i2c_psu_status
QSFPs
QSFP modules are managed by the pca9548 kernel driver.
The i2c utility /usr/sbin/i2c_utils.sh can be used to get status and
module EEPROM informations.
The usage as follows:
QSFP EEPROM:
i2c_utils.sh i2c_qsfp_eeprom_get [1-64]
QSFP Insert Event:
i2c_utils.sh i2c_qsfp_eeprom_get [1-64]
0 => not insert
1 => inserted