194 строки
6.3 KiB
Bash
194 строки
6.3 KiB
Bash
#!/bin/sh
|
|
#
|
|
# ip-up.ipv6to4
|
|
#
|
|
#
|
|
# Taken from:
|
|
# (P) & (C) 2000-2005 by Peter Bieringer <pb@bieringer.de>
|
|
#
|
|
# You will find more information on the initscripts-ipv6 homepage at
|
|
# http://www.deepspace6.net/projects/initscripts-ipv6.html
|
|
#
|
|
# Version: 2005-09-22
|
|
#
|
|
# Calling parameters:
|
|
# $1: interface name
|
|
#
|
|
# Called (mostly) by /etc/ppp/ip-up.local
|
|
# like: /etc/ppp/ip-up.ipv6to4 $1 >>/var/log/ppp-ipv6to4.log 2>&1
|
|
#
|
|
# Note: this script will *kill* older still existing 6to4 tunnels regardless
|
|
# whether they were set before by another device
|
|
#
|
|
# Uses following information from /etc/sysconfig/network-scripts/ifcfg-$1:
|
|
# IPV6TO4INIT=yes|no: controls configuration
|
|
# IPV6TO4_IPV4ADDR=<IPv4 address>: special local address for 6to4 tunneling (only needed behind a NAT gateway)
|
|
# IPV6TO4_RELAY=<IPv4 address>: remote 6to4 relay router address (default: 192.88.99.1)
|
|
# IPV6TO4_MTU=<MTU for IPv6>: controls IPv6 MTU for the 6to4 link (optional, default is MTU of interface - 20)
|
|
# IPV6TO4_ROUTING="<device>-<suffix>/<prefix length> ...": information to setup additional interfaces
|
|
# Example: IPV6TO4_ROUTING="eth0-:f101::1/64 eth1-:f102::1/64"
|
|
#
|
|
# IPV6_CONTROL_RADVD=yes|no: controls radvd triggering
|
|
# IPV6_RADVD_PIDFILE=<file>: PID file of radvd for sending signals, default is "/var/run/radvd/radvd.pid"
|
|
# IPV6_RADVD_TRIGGER_ACTION=startstop|reload|restart|SIGHUP: how to trigger radvd (optional, default is SIGHUP)
|
|
#
|
|
# Requirements
|
|
# radvd-0.6.2p3 or newer supporting option "Base6to4Interface"
|
|
#
|
|
|
|
|
|
if [ -z "$1" ]; then
|
|
echo $"Argument 1 is empty but should contain interface name - skip IPv6to4 initialization"
|
|
exit 1
|
|
fi
|
|
|
|
# Get global network configuration
|
|
. /etc/sysconfig/network
|
|
|
|
# Source IPv4 helper functions
|
|
cd /etc/sysconfig/network-scripts
|
|
. ./network-functions
|
|
|
|
CONFIG=$1
|
|
[ -f "$CONFIG" ] || CONFIG=ifcfg-$CONFIG
|
|
source_config
|
|
|
|
# IPv6 don't need aliases anymore, config is skipped
|
|
REALDEVICE=${DEVICE%%:*}
|
|
[ "$DEVICE" != "$REALDEVICE" ] && exit 0
|
|
|
|
if [ ! -f /etc/sysconfig/network-scripts/network-functions-ipv6 ]; then
|
|
exit 1
|
|
fi
|
|
|
|
. /etc/sysconfig/network-scripts/network-functions-ipv6
|
|
|
|
|
|
# Run basic IPv6 test (and make sure the ipv6 module will be loaded), if not ok, skip IPv6 initialization
|
|
ipv6_test || exit 1
|
|
|
|
# Setup of 6to4, if configured
|
|
valid6to4config="yes"
|
|
if [ "$IPV6TO4INIT" = "yes" ]; then
|
|
if [ -n "$IPV6TO4_IPV4ADDR" ]; then
|
|
# Take 6to4-dedicated configured IPv4 address from config file (precedence 1)
|
|
ipv4addr="$IPV6TO4_IPV4ADDR"
|
|
else
|
|
# Get IPv4 address from interface (precedence 2)
|
|
ipv4addr="$(ipv6_get_ipv4addr_of_device $DEVICE)"
|
|
if [ -z "$ipv4addr" ]; then
|
|
# Take configured IPv4 address of interface from config file (precedence 3)
|
|
ipv4addr="$IPADDR"
|
|
fi
|
|
fi
|
|
if [ -n "$ipv4addr" ]; then
|
|
# Test for non-global IPv4 address
|
|
if ! ipv6_test_ipv4_addr_global_usable $ipv4addr; then
|
|
net_log $"Given IPv4 address '$ipv4addr' is not globally usable" info
|
|
valid6to4config="no"
|
|
fi
|
|
else
|
|
net_log $"IPv6to4 configuration needs an IPv4 address on related interface or otherwise specified" info
|
|
valid6to4config="no"
|
|
fi
|
|
if [ -z "$IPV6TO4_RELAY" ]; then
|
|
IPV6TO4_RELAY="192.88.99.1"
|
|
fi
|
|
|
|
# Check/generate relay address
|
|
ipv6to4_relay="$(ipv6_create_6to4_relay_address $IPV6TO4_RELAY)"
|
|
if [ $? -ne 0 ]; then
|
|
valid6to4config="no"
|
|
fi
|
|
|
|
if [ "$valid6to4config" = "yes" ]; then
|
|
# Delete routes to local networks
|
|
for devsuf in $IPV6TO4_ROUTING; do
|
|
dev="${devsuf%%-*}"
|
|
ipv6_cleanup_6to4_device $dev
|
|
done
|
|
|
|
# Cleanup all old data (needed, if "ip-down.ipv6to4" wasn't executed), delete all configured 6to4 address
|
|
ipv6_cleanup_6to4_tunnels tun6to4
|
|
|
|
# Get MTU of master device
|
|
ipv4mtu="$(/sbin/ip link show dev $DEVICE | awk '/\<mtu\>/ { print $5 }')"
|
|
if [ -n "$ipv4mtu" ]; then
|
|
# IPv6 tunnel MTU is IPv4 MTU minus 20 for IPv4 header
|
|
tunnelmtu=$[ $ipv4mtu - 20 ]
|
|
fi
|
|
|
|
if [ -n "$IPV6TO4_MTU" ]; then
|
|
if [ $IPV6TO4_MTU -gt $tunnelmtu ]; then
|
|
net_log $"Warning: configured MTU '$IPV6TO4_MTU' for 6to4 exceeds maximum limit of '$tunnelmtu', ignored" warning
|
|
else
|
|
tunnelmtu=$IPV6TO4_MTU
|
|
fi
|
|
fi
|
|
|
|
# Setup new data
|
|
ipv6_add_6to4_tunnel tun6to4 $ipv4addr "" $tunnelmtu || exit 1
|
|
|
|
# Add route to for compatible addresses (removed later again)
|
|
ipv6_add_route "::/96" "::" tun6to4
|
|
|
|
# Add default route, if device matches
|
|
if [ "$IPV6_DEFAULTDEV" = "tun6to4" ]; then
|
|
if [ -n "$IPV6_DEFAULTGW" ]; then
|
|
net_log $"Warning: interface 'tun6to4' does not support 'IPV6_DEFAULTGW', ignored" warning
|
|
fi
|
|
ipv6_set_default_route $ipv6to4_relay tun6to4
|
|
fi
|
|
|
|
# Add static routes
|
|
if [ -f /etc/sysconfig/static-routes-ipv6 ]; then
|
|
LC_ALL=C grep -w "^tun6to4" /etc/sysconfig/static-routes-ipv6 | while read device network gateway; do
|
|
if [ -z "$network" ]; then
|
|
continue
|
|
fi
|
|
if [ -z "$gateway" ]; then
|
|
gateway="$ipv6to4_relay"
|
|
fi
|
|
ipv6_add_route $network $gateway tun6to4
|
|
done
|
|
fi
|
|
|
|
# Setup additional static IPv6 routes (newer config style)
|
|
if [ -f "/etc/sysconfig/network-scripts/route6-tun6to4" ]; then
|
|
sed -ne 's/#.*//' -e '/[^[:space:]]/p' /etc/sysconfig/network-scripts/route6-tun6to4 | while read line; do
|
|
if echo "$line" | grep -vq 'via'; then
|
|
# Add gateway if missing
|
|
line="$line via $ipv6to4_relay"
|
|
fi
|
|
/sbin/ip -6 route add $line
|
|
done
|
|
fi
|
|
|
|
# Cleanup autmatically generated autotunnel (not needed for 6to4)
|
|
/sbin/ip -6 route del ::/96 dev tun6to4
|
|
/sbin/ip -6 addr del tun6to4 "::$ipv4addr/128" dev tun6to4
|
|
|
|
if [ "$IPV6_CONTROL_RADVD" = "yes" ]; then
|
|
# Control running radvd
|
|
ipv6_trigger_radvd up "$IPV6_RADVD_TRIGGER_ACTION" $IPV6_RADVD_PIDFILE
|
|
|
|
if [ -n "$IPV6TO4_ROUTING" ]; then
|
|
# Generate 6to4 address
|
|
ipv6to4prefix="$(ipv6_create_6to4_prefix $ipv4addr)"
|
|
if [ -n "$ipv6to4prefix" ]; then
|
|
# Add IPv6 address to interface (required interface route will be set automatically)
|
|
for devsuf in $IPV6TO4_ROUTING; do
|
|
dev="${devsuf%%-*}"
|
|
suf="$(echo $devsuf | awk -F- '{ print $2 }')"
|
|
ipv6_add_addr_on_device ${dev} ${ipv6to4prefix}${suf}
|
|
done
|
|
else
|
|
net_log $"Error occurred while calculating the IPv6to4 prefix"
|
|
fi
|
|
else
|
|
net_log $"radvd control enabled, but config is not complete"
|
|
fi
|
|
fi
|
|
fi
|
|
fi
|