microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/drivers/md/raid5-log.h

155 строки
4.7 KiB
C
Исходник Постоянная ссылка Обычный вид История

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 17:07:57 +03:00
/* SPDX-License-Identifier: GPL-2.0 */
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
#ifndef _RAID5_LOG_H
#define _RAID5_LOG_H
extern int r5l_init_log(struct r5conf *conf, struct md_rdev *rdev);
extern void r5l_exit_log(struct r5conf *conf);
extern int r5l_write_stripe(struct r5l_log *log, struct stripe_head *head_sh);
extern void r5l_write_stripe_run(struct r5l_log *log);
extern void r5l_flush_stripe_to_raid(struct r5l_log *log);
extern void r5l_stripe_write_finished(struct stripe_head *sh);
extern int r5l_handle_flush_request(struct r5l_log *log, struct bio *bio);
md: remove special meaning of ->quiesce(.., 2) The '2' argument means "wake up anything that is waiting". This is an inelegant part of the design and was added to help support management of suspend_lo/suspend_hi setting. Now that suspend_lo/hi is managed in mddev_suspend/resume, that need is gone. These is still a couple of places where we call 'quiesce' with an argument of '2', but they can safely be changed to call ->quiesce(.., 1); ->quiesce(.., 0) which achieve the same result at the small cost of pausing IO briefly. This removes a small "optimization" from suspend_{hi,lo}_store, but it isn't clear that optimization served a useful purpose. The code now is a lot clearer. Suggested-by: Shaohua Li <shli@kernel.org> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-10-19 04:49:15 +03:00
extern void r5l_quiesce(struct r5l_log *log, int quiesce);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
extern bool r5l_log_disk_error(struct r5conf *conf);
extern bool r5c_is_writeback(struct r5l_log *log);
extern int
r5c_try_caching_write(struct r5conf *conf, struct stripe_head *sh,
struct stripe_head_state *s, int disks);
extern void
r5c_finish_stripe_write_out(struct r5conf *conf, struct stripe_head *sh,
struct stripe_head_state *s);
extern void r5c_release_extra_page(struct stripe_head *sh);
extern void r5c_use_extra_page(struct stripe_head *sh);
extern void r5l_wake_reclaim(struct r5l_log *log, sector_t space);
extern void r5c_handle_cached_data_endio(struct r5conf *conf,
md/raid5: call bio_endio() directly rather than queueing for later. We currently gather bios that need to be returned into a bio_list and call bio_endio() on them all together. The original reason for this was to avoid making the calls while holding a spinlock. Locking has changed a lot since then, and that reason is no longer valid. So discard return_io() and various return_bi lists, and just call bio_endio() directly as needed. Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-15 06:05:12 +03:00
struct stripe_head *sh, int disks);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
extern int r5c_cache_data(struct r5l_log *log, struct stripe_head *sh);
extern void r5c_make_stripe_write_out(struct stripe_head *sh);
extern void r5c_flush_cache(struct r5conf *conf, int num);
extern void r5c_check_stripe_cache_usage(struct r5conf *conf);
extern void r5c_check_cached_full_stripe(struct r5conf *conf);
extern struct md_sysfs_entry r5c_journal_mode;
md/r5cache: gracefully handle journal device errors for writeback mode For the raid456 with writeback cache, when journal device failed during normal operation, it is still possible to persist all data, as all pending data is still in stripe cache. However, it is necessary to handle journal failure gracefully. During journal failures, the following logic handles the graceful shutdown of journal: 1. raid5_error() marks the device as Faulty and schedules async work log->disable_writeback_work; 2. In disable_writeback_work (r5c_disable_writeback_async), the mddev is suspended, set to write through, and then resumed. mddev_suspend() flushes all cached stripes; 3. All cached stripes need to be flushed carefully to the RAID array. This patch fixes issues within the process above: 1. In r5c_update_on_rdev_error() schedule disable_writeback_work for journal failures; 2. In r5c_disable_writeback_async(), wait for MD_SB_CHANGE_PENDING, since raid5_error() updates superblock. 3. In handle_stripe(), allow stripes with data in journal (s.injournal > 0) to make progress during log_failed; 4. In delay_towrite(), if log failed only process data in the cache (skip new writes in dev->towrite); 5. In __get_priority_stripe(), process loprio_list during journal device failures. 6. In raid5_remove_disk(), wait for all cached stripes are flushed before calling log_exit(). Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-05-12 01:28:28 +03:00
extern void r5c_update_on_rdev_error(struct mddev *mddev,
struct md_rdev *rdev);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
extern bool r5c_big_stripe_cached(struct r5conf *conf, sector_t sect);
md: introduce new personality funciton start() In do_md_run(), md threads should not wake up until the array is fully initialized in md_run(). However, in raid5_run(), raid5-cache may wake up mddev->thread to flush stripes that need to be written back. This design doesn't break badly right now. But it could lead to bad bug in the future. This patch tries to resolve this problem by splitting start up work into two personality functions, run() and start(). Tasks that do not require the md threads should go into run(), while task that require the md threads go into start(). r5l_load_log() is moved to raid5_start(), so it is not called until the md threads are started in do_md_run(). Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-11-20 09:17:01 +03:00
extern int r5l_start(struct r5l_log *log);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
extern struct dma_async_tx_descriptor *
ops_run_partial_parity(struct stripe_head *sh, struct raid5_percpu *percpu,
struct dma_async_tx_descriptor *tx);
extern int ppl_init_log(struct r5conf *conf);
extern void ppl_exit_log(struct r5conf *conf);
extern int ppl_write_stripe(struct r5conf *conf, struct stripe_head *sh);
extern void ppl_write_stripe_run(struct r5conf *conf);
extern void ppl_stripe_write_finished(struct stripe_head *sh);
raid5-ppl: support disk hot add/remove with PPL Add a function to modify the log by removing an rdev when a drive fails or adding when a spare/replacement is activated as a raid member. Removing a disk just clears the child log rdev pointer. No new stripes will be accepted for this child log in ppl_write_stripe() and running io units will be processed without writing PPL to the device. Adding a disk sets the child log rdev pointer and writes an empty PPL header. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 12:00:02 +03:00
extern int ppl_modify_log(struct r5conf *conf, struct md_rdev *rdev, bool add);
raid5-ppl: PPL support for disks with write-back cache enabled In order to provide data consistency with PPL for disks with write-back cache enabled all data has to be flushed to disks before next PPL entry. The disks to be flushed are marked in the bitmap. It's modified under a mutex and it's only read after PPL io unit is submitted. A limitation of 64 disks in the array has been introduced to keep data structures and implementation simple. RAID5 arrays with so many disks are not likely due to high risk of multiple disks failure. Such restriction should not be a real life limitation. With write-back cache disabled next PPL entry is submitted when data write for current one completes. Data flush defers next log submission so trigger it when there are no stripes for handling found. As PPL assures all data is flushed to disk at request completion, just acknowledge flush request when PPL is enabled. Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2017-12-27 12:31:40 +03:00
extern void ppl_quiesce(struct r5conf *conf, int quiesce);
raid5-ppl: fix handling flush requests Add missing bio completion. Without this any flush request would hang. Fixes: 1532d9e87e8b ("raid5-ppl: PPL support for disks with write-back cache enabled") Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2018-02-20 12:10:36 +03:00
extern int ppl_handle_flush_request(struct r5l_log *log, struct bio *bio);
raid5: set write hint for PPL When the Partial Parity Log is enabled, circular buffer is used to store PPL data. Each write to RAID device causes overwrite of data in this buffer so some write_hint can be set to those request to help drives handle garbage collection. This patch adds new sysfs attribute which can be used to specify which write_hint should be assigned to PPL. Acked-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Mariusz Dabrowski <mariusz.dabrowski@intel.com> Signed-off-by: Song Liu <songliubraving@fb.com>
2019-02-18 17:04:09 +03:00
extern struct md_sysfs_entry ppl_write_hint;
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
md/raid5-cache: disable reshape completely We don't support reshape yet if an array supports log device. Previously we determine the fact by checking ->log. However, ->log could be NULL after a log device is removed, but the array is still marked to support log device. Don't allow reshape in this case too. User can disable log device support by setting 'consistency_policy' to 'resync' then do reshape. Reported-by: Xiao Ni <xni@redhat.com> Tested-by: Xiao Ni <xni@redhat.com> Signed-off-by: Shaohua Li <shli@fb.com>
2018-08-29 21:05:42 +03:00
static inline bool raid5_has_log(struct r5conf *conf)
{
return test_bit(MD_HAS_JOURNAL, &conf->mddev->flags);
}
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
static inline bool raid5_has_ppl(struct r5conf *conf)
{
return test_bit(MD_HAS_PPL, &conf->mddev->flags);
}
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
static inline int log_stripe(struct stripe_head *sh, struct stripe_head_state *s)
{
struct r5conf *conf = sh->raid_conf;
if (conf->log) {
if (!test_bit(STRIPE_R5C_CACHING, &sh->state)) {
/* writing out phase */
if (s->waiting_extra_page)
return 0;
return r5l_write_stripe(conf->log, sh);
} else if (test_bit(STRIPE_LOG_TRAPPED, &sh->state)) {
/* caching phase */
return r5c_cache_data(conf->log, sh);
}
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
} else if (raid5_has_ppl(conf)) {
return ppl_write_stripe(conf, sh);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
}
return -EAGAIN;
}
static inline void log_stripe_write_finished(struct stripe_head *sh)
{
struct r5conf *conf = sh->raid_conf;
if (conf->log)
r5l_stripe_write_finished(sh);
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
else if (raid5_has_ppl(conf))
ppl_stripe_write_finished(sh);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
}
static inline void log_write_stripe_run(struct r5conf *conf)
{
if (conf->log)
r5l_write_stripe_run(conf->log);
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
else if (raid5_has_ppl(conf))
ppl_write_stripe_run(conf);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
}
raid5-ppl: PPL support for disks with write-back cache enabled In order to provide data consistency with PPL for disks with write-back cache enabled all data has to be flushed to disks before next PPL entry. The disks to be flushed are marked in the bitmap. It's modified under a mutex and it's only read after PPL io unit is submitted. A limitation of 64 disks in the array has been introduced to keep data structures and implementation simple. RAID5 arrays with so many disks are not likely due to high risk of multiple disks failure. Such restriction should not be a real life limitation. With write-back cache disabled next PPL entry is submitted when data write for current one completes. Data flush defers next log submission so trigger it when there are no stripes for handling found. As PPL assures all data is flushed to disk at request completion, just acknowledge flush request when PPL is enabled. Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2017-12-27 12:31:40 +03:00
static inline void log_flush_stripe_to_raid(struct r5conf *conf)
{
if (conf->log)
r5l_flush_stripe_to_raid(conf->log);
else if (raid5_has_ppl(conf))
ppl_write_stripe_run(conf);
}
static inline int log_handle_flush_request(struct r5conf *conf, struct bio *bio)
{
int ret = -ENODEV;
if (conf->log)
ret = r5l_handle_flush_request(conf->log, bio);
else if (raid5_has_ppl(conf))
raid5-ppl: fix handling flush requests Add missing bio completion. Without this any flush request would hang. Fixes: 1532d9e87e8b ("raid5-ppl: PPL support for disks with write-back cache enabled") Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2018-02-20 12:10:36 +03:00
ret = ppl_handle_flush_request(conf->log, bio);
raid5-ppl: PPL support for disks with write-back cache enabled In order to provide data consistency with PPL for disks with write-back cache enabled all data has to be flushed to disks before next PPL entry. The disks to be flushed are marked in the bitmap. It's modified under a mutex and it's only read after PPL io unit is submitted. A limitation of 64 disks in the array has been introduced to keep data structures and implementation simple. RAID5 arrays with so many disks are not likely due to high risk of multiple disks failure. Such restriction should not be a real life limitation. With write-back cache disabled next PPL entry is submitted when data write for current one completes. Data flush defers next log submission so trigger it when there are no stripes for handling found. As PPL assures all data is flushed to disk at request completion, just acknowledge flush request when PPL is enabled. Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2017-12-27 12:31:40 +03:00
return ret;
}
static inline void log_quiesce(struct r5conf *conf, int quiesce)
{
if (conf->log)
r5l_quiesce(conf->log, quiesce);
else if (raid5_has_ppl(conf))
ppl_quiesce(conf, quiesce);
}
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
static inline void log_exit(struct r5conf *conf)
{
if (conf->log)
r5l_exit_log(conf);
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
else if (raid5_has_ppl(conf))
ppl_exit_log(conf);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
}
raid5-ppl: use resize_stripes() when enabling or disabling ppl Use resize_stripes() instead of raid5_reset_stripe_cache() to allocate or free sh->ppl_page at runtime for all stripes in the stripe cache. raid5_reset_stripe_cache() required suspending the mddev and could deadlock because of GFP_KERNEL allocations. Move the 'newsize' check to check_reshape() to allow reallocating the stripes with the same number of disks. Allocate sh->ppl_page in alloc_stripe() instead of grow_buffers(). Pass 'struct r5conf *conf' as a parameter to alloc_stripe() because it is needed to check whether to allocate ppl_page. Add free_stripe() and use it to free stripes rather than directly call kmem_cache_free(). Also free sh->ppl_page in free_stripe(). Set MD_HAS_PPL at the end of ppl_init_log() instead of explicitly setting it in advance and add another parameter to log_init() to allow calling ppl_init_log() without the bit set. Don't try to calculate partial parity or add a stripe to log if it does not have ppl_page set. Enabling ppl can now be performed without suspending the mddev, because the log won't be used until new stripes are allocated with ppl_page. Calling mddev_suspend/resume is still necessary when disabling ppl, because we want all stripes to finish before stopping the log, but resize_stripes() can be called after mddev_resume() when ppl is no longer active. Suggested-by: NeilBrown <neilb@suse.com> Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-04-04 14:13:57 +03:00
static inline int log_init(struct r5conf *conf, struct md_rdev *journal_dev,
bool ppl)
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
{
if (journal_dev)
return r5l_init_log(conf, journal_dev);
raid5-ppl: use resize_stripes() when enabling or disabling ppl Use resize_stripes() instead of raid5_reset_stripe_cache() to allocate or free sh->ppl_page at runtime for all stripes in the stripe cache. raid5_reset_stripe_cache() required suspending the mddev and could deadlock because of GFP_KERNEL allocations. Move the 'newsize' check to check_reshape() to allow reallocating the stripes with the same number of disks. Allocate sh->ppl_page in alloc_stripe() instead of grow_buffers(). Pass 'struct r5conf *conf' as a parameter to alloc_stripe() because it is needed to check whether to allocate ppl_page. Add free_stripe() and use it to free stripes rather than directly call kmem_cache_free(). Also free sh->ppl_page in free_stripe(). Set MD_HAS_PPL at the end of ppl_init_log() instead of explicitly setting it in advance and add another parameter to log_init() to allow calling ppl_init_log() without the bit set. Don't try to calculate partial parity or add a stripe to log if it does not have ppl_page set. Enabling ppl can now be performed without suspending the mddev, because the log won't be used until new stripes are allocated with ppl_page. Calling mddev_suspend/resume is still necessary when disabling ppl, because we want all stripes to finish before stopping the log, but resize_stripes() can be called after mddev_resume() when ppl is no longer active. Suggested-by: NeilBrown <neilb@suse.com> Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-04-04 14:13:57 +03:00
else if (ppl)
raid5-ppl: Partial Parity Log write logging implementation Implement the calculation of partial parity for a stripe and PPL write logging functionality. The description of PPL is added to the documentation. More details can be found in the comments in raid5-ppl.c. Attach a page for holding the partial parity data to stripe_head. Allocate it only if mddev has the MD_HAS_PPL flag set. Partial parity is the xor of not modified data chunks of a stripe and is calculated as follows: - reconstruct-write case: xor data from all not updated disks in a stripe - read-modify-write case: xor old data and parity from all updated disks in a stripe Implement it using the async_tx API and integrate into raid_run_ops(). It must be called when we still have access to old data, so do it when STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is stored into sh->ppl_page. Partial parity is not meaningful for full stripe write and is not stored in the log or used for recovery, so don't attempt to calculate it when stripe has STRIPE_FULL_WRITE. Put the PPL metadata structures to md_p.h because userspace tools (mdadm) will also need to read/write PPL. Warn about using PPL with enabled disk volatile write-back cache for now. It can be removed once disk cache flushing before writing PPL is implemented. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:59 +03:00
return ppl_init_log(conf);
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
return 0;
}
raid5-ppl: support disk hot add/remove with PPL Add a function to modify the log by removing an rdev when a drive fails or adding when a spare/replacement is activated as a raid member. Removing a disk just clears the child log rdev pointer. No new stripes will be accepted for this child log in ppl_write_stripe() and running io units will be processed without writing PPL to the device. Adding a disk sets the child log rdev pointer and writes an empty PPL header. Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 12:00:02 +03:00
static inline int log_modify(struct r5conf *conf, struct md_rdev *rdev, bool add)
{
if (raid5_has_ppl(conf))
return ppl_modify_log(conf, rdev, add);
return 0;
}
raid5: separate header for log functions Move raid5-cache declarations from raid5.h to raid5-log.h, add inline wrappers for functions which will be shared with ppl and use them in raid5 core instead of direct calls to raid5-cache. Remove unused parameter from r5c_cache_data(), move two duplicated pr_debug() calls to r5l_init_log(). Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
2017-03-09 11:59:58 +03:00
#endif