WSL2-Linux-Kernel/include/asm-v850/rte_nb85e_cb.h

112 строки
3.5 KiB
C
Исходник Обычный вид История

/*
* include/asm-v850/rte_nb85e_cb.h -- Midas labs RTE-V850/NB85E-CB board
*
* Copyright (C) 2001,02,03 NEC Electronics Corporation
* Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
*
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file COPYING in the main directory of this
* archive for more details.
*
* Written by Miles Bader <miles@gnu.org>
*/
#ifndef __V850_RTE_NB85E_CB_H__
#define __V850_RTE_NB85E_CB_H__
#include <asm/rte_cb.h> /* Common defs for Midas RTE-CB boards. */
#define PLATFORM "rte-v850e/nb85e-cb"
#define PLATFORM_LONG "Midas lab RTE-V850E/NB85E-CB"
#define CPU_CLOCK_FREQ 50000000 /* 50MHz */
/* 1MB of onboard SRAM. Note that the monitor ROM uses parts of this
for its own purposes, so care must be taken. */
#define SRAM_ADDR 0x03C00000
#define SRAM_SIZE 0x00100000 /* 1MB */
/* 16MB of onbard SDRAM. */
#define SDRAM_ADDR 0x01000000
#define SDRAM_SIZE 0x01000000 /* 16MB */
/* CPU addresses of GBUS memory spaces. */
#define GCS0_ADDR 0x00400000 /* GCS0 - Common SRAM (2MB) */
#define GCS0_SIZE 0x00400000 /* 4MB */
#define GCS1_ADDR 0x02000000 /* GCS1 - Flash ROM (8MB) */
#define GCS1_SIZE 0x00800000 /* 8MB */
#define GCS2_ADDR 0x03900000 /* GCS2 - I/O registers */
#define GCS2_SIZE 0x00080000 /* 512KB */
#define GCS3_ADDR 0x02800000 /* GCS3 - EXT-bus: memory space */
#define GCS3_SIZE 0x00800000 /* 8MB */
#define GCS4_ADDR 0x03A00000 /* GCS4 - EXT-bus: I/O space */
#define GCS4_SIZE 0x00200000 /* 2MB */
#define GCS5_ADDR 0x00800000 /* GCS5 - PCI bus space */
#define GCS5_SIZE 0x00800000 /* 8MB */
#define GCS6_ADDR 0x03980000 /* GCS6 - PCI control registers */
#define GCS6_SIZE 0x00010000 /* 64KB */
/* The GBUS GINT0 - GINT3 interrupts are connected to CPU interrupts 10-12.
These are shared among the GBUS interrupts. */
#define IRQ_GINT(n) (10 + (n))
#define IRQ_GINT_NUM 3
/* Used by <asm/rte_cb.h> to derive NUM_MACH_IRQS. */
#define NUM_RTE_CB_IRQS NUM_CPU_IRQS
#ifdef CONFIG_ROM_KERNEL
/* Kernel is in ROM, starting at address 0. */
#define INTV_BASE 0
#else /* !CONFIG_ROM_KERNEL */
/* We're using the ROM monitor. */
/* The chip's real interrupt vectors are in ROM, but they jump to a
secondary interrupt vector table in RAM. */
#define INTV_BASE 0x03CF8000
/* Scratch memory used by the ROM monitor, which shouldn't be used by
linux (except for the alternate interrupt vector area, defined
above). */
#define MON_SCRATCH_ADDR 0x03CE8000
#define MON_SCRATCH_SIZE 0x00018000 /* 96KB */
#endif /* CONFIG_ROM_KERNEL */
/* Some misc. on-board devices. */
/* Seven-segment LED display (two digits). Write-only. */
#define LED_ADDR(n) (0x03802000 + (n))
#define LED(n) (*(volatile unsigned char *)LED_ADDR(n))
#define LED_NUM_DIGITS 4
/* Override the basic TEG UART pre-initialization so that we can
initialize extra stuff. */
#undef V850E_UART_PRE_CONFIGURE /* should be defined by <asm/teg.h> */
#define V850E_UART_PRE_CONFIGURE rte_nb85e_cb_uart_pre_configure
#ifndef __ASSEMBLY__
extern void rte_nb85e_cb_uart_pre_configure (unsigned chan,
unsigned cflags, unsigned baud);
#endif
/* This board supports RTS/CTS for the on-chip UART. */
/* CTS is pin P00. */
#define V850E_UART_CTS(chan) (! (TEG_PORT0_IO & 0x1))
/* RTS is pin P02. */
#define V850E_UART_SET_RTS(chan, val) \
do { \
unsigned old = TEG_PORT0_IO; \
TEG_PORT0_IO = val ? (old & ~0x4) : (old | 0x4); \
} while (0)
#endif /* __V850_RTE_NB85E_CB_H__ */