net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
/*
|
|
|
|
* include/net/dsa.h - Driver for Distributed Switch Architecture switch chips
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
* Copyright (c) 2008-2009 Marvell Semiconductor
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
|
|
* (at your option) any later version.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#ifndef __LINUX_NET_DSA_H
|
|
|
|
#define __LINUX_NET_DSA_H
|
|
|
|
|
2017-02-08 02:03:05 +03:00
|
|
|
#include <linux/if.h>
|
2011-12-01 02:07:18 +04:00
|
|
|
#include <linux/if_ether.h>
|
2011-11-27 21:06:08 +04:00
|
|
|
#include <linux/list.h>
|
2017-02-03 21:20:20 +03:00
|
|
|
#include <linux/notifier.h>
|
2011-11-25 18:32:52 +04:00
|
|
|
#include <linux/timer.h>
|
|
|
|
#include <linux/workqueue.h>
|
2014-08-28 04:04:49 +04:00
|
|
|
#include <linux/of.h>
|
2014-10-18 03:02:13 +04:00
|
|
|
#include <linux/ethtool.h>
|
2017-03-29 00:45:07 +03:00
|
|
|
#include <net/devlink.h>
|
2017-05-17 22:46:04 +03:00
|
|
|
#include <net/switchdev.h>
|
2011-11-25 18:32:52 +04:00
|
|
|
|
2017-01-30 23:41:40 +03:00
|
|
|
struct tc_action;
|
2017-02-08 02:03:05 +03:00
|
|
|
struct phy_device;
|
|
|
|
struct fixed_phy_status;
|
2017-01-30 23:41:40 +03:00
|
|
|
|
2014-09-12 08:18:09 +04:00
|
|
|
enum dsa_tag_protocol {
|
|
|
|
DSA_TAG_PROTO_NONE = 0,
|
2017-05-16 23:40:07 +03:00
|
|
|
DSA_TAG_PROTO_BRCM,
|
2014-09-12 08:18:09 +04:00
|
|
|
DSA_TAG_PROTO_DSA,
|
|
|
|
DSA_TAG_PROTO_EDSA,
|
2017-05-31 23:19:06 +03:00
|
|
|
DSA_TAG_PROTO_KSZ,
|
2017-04-18 11:48:24 +03:00
|
|
|
DSA_TAG_PROTO_LAN9303,
|
2017-05-16 23:40:07 +03:00
|
|
|
DSA_TAG_PROTO_MTK,
|
|
|
|
DSA_TAG_PROTO_QCA,
|
|
|
|
DSA_TAG_PROTO_TRAILER,
|
2016-06-04 22:17:03 +03:00
|
|
|
DSA_TAG_LAST, /* MUST BE LAST */
|
2014-09-12 08:18:09 +04:00
|
|
|
};
|
2014-08-28 04:04:55 +04:00
|
|
|
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
#define DSA_MAX_SWITCHES 4
|
|
|
|
#define DSA_MAX_PORTS 12
|
|
|
|
|
2016-07-07 03:03:54 +03:00
|
|
|
#define DSA_RTABLE_NONE -1
|
|
|
|
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
struct dsa_chip_data {
|
|
|
|
/*
|
|
|
|
* How to access the switch configuration registers.
|
|
|
|
*/
|
2014-09-15 21:00:27 +04:00
|
|
|
struct device *host_dev;
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
int sw_addr;
|
|
|
|
|
2017-02-05 00:02:43 +03:00
|
|
|
/*
|
|
|
|
* Reference to network devices
|
|
|
|
*/
|
|
|
|
struct device *netdev[DSA_MAX_PORTS];
|
|
|
|
|
2014-10-29 20:45:01 +03:00
|
|
|
/* set to size of eeprom if supported by the switch */
|
|
|
|
int eeprom_len;
|
|
|
|
|
2014-08-28 04:04:49 +04:00
|
|
|
/* Device tree node pointer for this specific switch chip
|
|
|
|
* used during switch setup in case additional properties
|
|
|
|
* and resources needs to be used
|
|
|
|
*/
|
|
|
|
struct device_node *of_node;
|
|
|
|
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
/*
|
|
|
|
* The names of the switch's ports. Use "cpu" to
|
|
|
|
* designate the switch port that the cpu is connected to,
|
|
|
|
* "dsa" to indicate that this port is a DSA link to
|
|
|
|
* another switch, NULL to indicate the port is unused,
|
|
|
|
* or any other string to indicate this is a physical port.
|
|
|
|
*/
|
|
|
|
char *port_names[DSA_MAX_PORTS];
|
2014-08-28 04:04:50 +04:00
|
|
|
struct device_node *port_dn[DSA_MAX_PORTS];
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
|
|
|
|
/*
|
2016-06-04 22:16:59 +03:00
|
|
|
* An array of which element [a] indicates which port on this
|
|
|
|
* switch should be used to send packets to that are destined
|
|
|
|
* for switch a. Can be NULL if there is only one switch chip.
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
*/
|
2016-06-04 22:16:59 +03:00
|
|
|
s8 rtable[DSA_MAX_SWITCHES];
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
};
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
|
|
|
|
struct dsa_platform_data {
|
|
|
|
/*
|
|
|
|
* Reference to a Linux network interface that connects
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
* to the root switch chip of the tree.
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
*/
|
|
|
|
struct device *netdev;
|
2015-03-10 00:31:21 +03:00
|
|
|
struct net_device *of_netdev;
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
|
|
|
|
/*
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
* Info structs describing each of the switch chips
|
|
|
|
* connected via this network interface.
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
*/
|
dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
|
|
|
int nr_chips;
|
|
|
|
struct dsa_chip_data *chip;
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
};
|
|
|
|
|
2014-09-15 21:00:19 +04:00
|
|
|
struct packet_type;
|
2014-08-28 04:04:46 +04:00
|
|
|
|
2017-08-09 15:41:16 +03:00
|
|
|
struct dsa_device_ops {
|
|
|
|
struct sk_buff *(*xmit)(struct sk_buff *skb, struct net_device *dev);
|
|
|
|
struct sk_buff *(*rcv)(struct sk_buff *skb, struct net_device *dev,
|
2017-08-17 17:47:00 +03:00
|
|
|
struct packet_type *pt);
|
2017-08-09 15:41:17 +03:00
|
|
|
int (*flow_dissect)(const struct sk_buff *skb, __be16 *proto,
|
|
|
|
int *offset);
|
2017-08-09 15:41:16 +03:00
|
|
|
};
|
|
|
|
|
2011-11-25 18:32:52 +04:00
|
|
|
struct dsa_switch_tree {
|
2016-06-04 22:17:07 +03:00
|
|
|
struct list_head list;
|
|
|
|
|
2017-02-03 21:20:20 +03:00
|
|
|
/* Notifier chain for switch-wide events */
|
|
|
|
struct raw_notifier_head nh;
|
|
|
|
|
2016-06-04 22:17:07 +03:00
|
|
|
/* Tree identifier */
|
2017-11-04 02:05:21 +03:00
|
|
|
unsigned int index;
|
2016-06-04 22:17:07 +03:00
|
|
|
|
|
|
|
/* Number of switches attached to this tree */
|
|
|
|
struct kref refcount;
|
|
|
|
|
|
|
|
/* Has this tree been applied to the hardware? */
|
|
|
|
bool applied;
|
|
|
|
|
2011-11-25 18:32:52 +04:00
|
|
|
/*
|
|
|
|
* Configuration data for the platform device that owns
|
|
|
|
* this dsa switch tree instance.
|
|
|
|
*/
|
|
|
|
struct dsa_platform_data *pd;
|
|
|
|
|
|
|
|
/*
|
2017-05-16 21:10:33 +03:00
|
|
|
* The switch port to which the CPU is attached.
|
2011-11-25 18:32:52 +04:00
|
|
|
*/
|
2017-05-16 21:10:33 +03:00
|
|
|
struct dsa_port *cpu_dp;
|
2011-11-25 18:32:52 +04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Data for the individual switch chips.
|
|
|
|
*/
|
|
|
|
struct dsa_switch *ds[DSA_MAX_SWITCHES];
|
|
|
|
};
|
|
|
|
|
2017-01-30 23:41:40 +03:00
|
|
|
/* TC matchall action types, only mirroring for now */
|
|
|
|
enum dsa_port_mall_action_type {
|
|
|
|
DSA_PORT_MALL_MIRROR,
|
|
|
|
};
|
|
|
|
|
|
|
|
/* TC mirroring entry */
|
|
|
|
struct dsa_mall_mirror_tc_entry {
|
|
|
|
u8 to_local_port;
|
|
|
|
bool ingress;
|
|
|
|
};
|
|
|
|
|
|
|
|
/* TC matchall entry */
|
|
|
|
struct dsa_mall_tc_entry {
|
|
|
|
struct list_head list;
|
|
|
|
unsigned long cookie;
|
|
|
|
enum dsa_port_mall_action_type type;
|
|
|
|
union {
|
|
|
|
struct dsa_mall_mirror_tc_entry mirror;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
|
2016-06-04 22:16:57 +03:00
|
|
|
struct dsa_port {
|
2017-10-16 18:12:18 +03:00
|
|
|
/* A CPU port is physically connected to a master device.
|
|
|
|
* A user port exposed to userspace has a slave device.
|
|
|
|
*/
|
|
|
|
union {
|
|
|
|
struct net_device *master;
|
|
|
|
struct net_device *slave;
|
|
|
|
};
|
|
|
|
|
2017-09-30 00:19:18 +03:00
|
|
|
/* CPU port tagging operations used by master or slave devices */
|
|
|
|
const struct dsa_device_ops *tag_ops;
|
|
|
|
|
2017-09-30 00:19:19 +03:00
|
|
|
/* Copies for faster access in master receive hot path */
|
|
|
|
struct dsa_switch_tree *dst;
|
|
|
|
struct sk_buff *(*rcv)(struct sk_buff *skb, struct net_device *dev,
|
|
|
|
struct packet_type *pt);
|
|
|
|
|
2017-10-26 18:22:57 +03:00
|
|
|
enum {
|
|
|
|
DSA_PORT_TYPE_UNUSED = 0,
|
|
|
|
DSA_PORT_TYPE_CPU,
|
|
|
|
DSA_PORT_TYPE_DSA,
|
|
|
|
DSA_PORT_TYPE_USER,
|
|
|
|
} type;
|
|
|
|
|
2017-01-27 23:29:38 +03:00
|
|
|
struct dsa_switch *ds;
|
|
|
|
unsigned int index;
|
2017-02-05 00:02:43 +03:00
|
|
|
const char *name;
|
2017-11-07 00:11:43 +03:00
|
|
|
const struct dsa_port *cpu_dp;
|
2016-06-04 22:16:58 +03:00
|
|
|
struct device_node *dn;
|
2016-07-19 03:45:38 +03:00
|
|
|
unsigned int ageing_time;
|
2016-09-22 23:49:22 +03:00
|
|
|
u8 stp_state;
|
2017-01-27 23:29:40 +03:00
|
|
|
struct net_device *bridge_dev;
|
2017-03-29 00:45:07 +03:00
|
|
|
struct devlink_port devlink_port;
|
2017-06-13 23:27:20 +03:00
|
|
|
/*
|
|
|
|
* Original copy of the master netdev ethtool_ops
|
|
|
|
*/
|
|
|
|
const struct ethtool_ops *orig_ethtool_ops;
|
2016-06-04 22:16:57 +03:00
|
|
|
};
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
struct dsa_switch {
|
2016-05-11 00:27:23 +03:00
|
|
|
struct device *dev;
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
/*
|
|
|
|
* Parent switch tree, and switch index.
|
|
|
|
*/
|
|
|
|
struct dsa_switch_tree *dst;
|
2017-11-04 02:05:20 +03:00
|
|
|
unsigned int index;
|
2011-11-27 21:06:08 +04:00
|
|
|
|
2017-02-03 21:20:20 +03:00
|
|
|
/* Listener for switch fabric events */
|
|
|
|
struct notifier_block nb;
|
|
|
|
|
2016-04-13 03:40:40 +03:00
|
|
|
/*
|
|
|
|
* Give the switch driver somewhere to hang its private data
|
|
|
|
* structure.
|
|
|
|
*/
|
|
|
|
void *priv;
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
/*
|
|
|
|
* Configuration data for this switch.
|
|
|
|
*/
|
2016-05-11 00:27:24 +03:00
|
|
|
struct dsa_chip_data *cd;
|
2011-11-27 21:06:08 +04:00
|
|
|
|
|
|
|
/*
|
2016-08-23 19:38:56 +03:00
|
|
|
* The switch operations.
|
2011-11-27 21:06:08 +04:00
|
|
|
*/
|
2017-01-09 01:52:08 +03:00
|
|
|
const struct dsa_switch_ops *ops;
|
2011-11-27 21:06:08 +04:00
|
|
|
|
2016-06-04 22:17:00 +03:00
|
|
|
/*
|
|
|
|
* An array of which element [a] indicates which port on this
|
|
|
|
* switch should be used to send packets to that are destined
|
|
|
|
* for switch a. Can be NULL if there is only one switch chip.
|
|
|
|
*/
|
|
|
|
s8 rtable[DSA_MAX_SWITCHES];
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
/*
|
|
|
|
* Slave mii_bus and devices for the individual ports.
|
|
|
|
*/
|
2014-08-28 04:04:51 +04:00
|
|
|
u32 phys_mii_mask;
|
2011-11-27 21:06:08 +04:00
|
|
|
struct mii_bus *slave_mii_bus;
|
2017-01-27 23:29:36 +03:00
|
|
|
|
2017-03-15 22:53:49 +03:00
|
|
|
/* Ageing Time limits in msecs */
|
|
|
|
unsigned int ageing_time_min;
|
|
|
|
unsigned int ageing_time_max;
|
|
|
|
|
2017-03-29 00:45:07 +03:00
|
|
|
/* devlink used to represent this switch device */
|
|
|
|
struct devlink *devlink;
|
|
|
|
|
2017-09-04 06:27:00 +03:00
|
|
|
/* Number of switch port queues */
|
|
|
|
unsigned int num_tx_queues;
|
|
|
|
|
2017-01-27 23:29:36 +03:00
|
|
|
/* Dynamically allocated ports, keep last */
|
|
|
|
size_t num_ports;
|
|
|
|
struct dsa_port ports[];
|
2011-11-27 21:06:08 +04:00
|
|
|
};
|
|
|
|
|
2017-10-26 18:22:58 +03:00
|
|
|
static inline const struct dsa_port *dsa_to_port(struct dsa_switch *ds, int p)
|
2017-10-26 18:22:51 +03:00
|
|
|
{
|
2017-10-26 18:22:58 +03:00
|
|
|
return &ds->ports[p];
|
|
|
|
}
|
2017-10-26 18:22:51 +03:00
|
|
|
|
2017-10-26 18:22:58 +03:00
|
|
|
static inline bool dsa_is_unused_port(struct dsa_switch *ds, int p)
|
|
|
|
{
|
|
|
|
return dsa_to_port(ds, p)->type == DSA_PORT_TYPE_UNUSED;
|
2017-10-26 18:22:51 +03:00
|
|
|
}
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
static inline bool dsa_is_cpu_port(struct dsa_switch *ds, int p)
|
|
|
|
{
|
2017-10-26 18:22:58 +03:00
|
|
|
return dsa_to_port(ds, p)->type == DSA_PORT_TYPE_CPU;
|
2011-11-27 21:06:08 +04:00
|
|
|
}
|
|
|
|
|
2015-08-18 00:52:51 +03:00
|
|
|
static inline bool dsa_is_dsa_port(struct dsa_switch *ds, int p)
|
|
|
|
{
|
2017-10-26 18:22:58 +03:00
|
|
|
return dsa_to_port(ds, p)->type == DSA_PORT_TYPE_DSA;
|
2015-08-18 00:52:51 +03:00
|
|
|
}
|
|
|
|
|
2017-10-26 18:22:54 +03:00
|
|
|
static inline bool dsa_is_user_port(struct dsa_switch *ds, int p)
|
2017-03-12 00:12:58 +03:00
|
|
|
{
|
2017-10-26 18:22:58 +03:00
|
|
|
return dsa_to_port(ds, p)->type == DSA_PORT_TYPE_USER;
|
2017-03-12 00:12:58 +03:00
|
|
|
}
|
|
|
|
|
2017-10-26 18:22:56 +03:00
|
|
|
static inline u32 dsa_user_ports(struct dsa_switch *ds)
|
|
|
|
{
|
2017-10-26 18:22:58 +03:00
|
|
|
u32 mask = 0;
|
|
|
|
int p;
|
2017-10-26 18:22:56 +03:00
|
|
|
|
2017-10-26 18:22:58 +03:00
|
|
|
for (p = 0; p < ds->num_ports; p++)
|
|
|
|
if (dsa_is_user_port(ds, p))
|
|
|
|
mask |= BIT(p);
|
|
|
|
|
|
|
|
return mask;
|
2017-10-16 18:12:19 +03:00
|
|
|
}
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
static inline u8 dsa_upstream_port(struct dsa_switch *ds)
|
|
|
|
{
|
|
|
|
struct dsa_switch_tree *dst = ds->dst;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* If this is the root switch (i.e. the switch that connects
|
|
|
|
* to the CPU), return the cpu port number on this switch.
|
|
|
|
* Else return the (DSA) port number that connects to the
|
|
|
|
* switch that is one hop closer to the cpu.
|
|
|
|
*/
|
2017-05-16 21:10:33 +03:00
|
|
|
if (dst->cpu_dp->ds == ds)
|
|
|
|
return dst->cpu_dp->index;
|
2011-11-27 21:06:08 +04:00
|
|
|
else
|
2017-05-16 21:10:33 +03:00
|
|
|
return ds->rtable[dst->cpu_dp->ds->index];
|
2011-11-27 21:06:08 +04:00
|
|
|
}
|
|
|
|
|
2017-08-06 16:15:49 +03:00
|
|
|
typedef int dsa_fdb_dump_cb_t(const unsigned char *addr, u16 vid,
|
|
|
|
bool is_static, void *data);
|
2016-08-23 19:38:56 +03:00
|
|
|
struct dsa_switch_ops {
|
2011-11-27 21:06:08 +04:00
|
|
|
/*
|
2017-04-12 19:45:03 +03:00
|
|
|
* Legacy probing.
|
2011-11-27 21:06:08 +04:00
|
|
|
*/
|
2016-04-17 20:23:55 +03:00
|
|
|
const char *(*probe)(struct device *dsa_dev,
|
|
|
|
struct device *host_dev, int sw_addr,
|
|
|
|
void **priv);
|
2016-08-22 17:01:01 +03:00
|
|
|
|
|
|
|
enum dsa_tag_protocol (*get_tag_protocol)(struct dsa_switch *ds);
|
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
int (*setup)(struct dsa_switch *ds);
|
2014-09-20 00:07:54 +04:00
|
|
|
u32 (*get_phy_flags)(struct dsa_switch *ds, int port);
|
2011-11-27 21:06:08 +04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Access to the switch's PHY registers.
|
|
|
|
*/
|
|
|
|
int (*phy_read)(struct dsa_switch *ds, int port, int regnum);
|
|
|
|
int (*phy_write)(struct dsa_switch *ds, int port,
|
|
|
|
int regnum, u16 val);
|
|
|
|
|
2014-08-28 04:04:53 +04:00
|
|
|
/*
|
|
|
|
* Link state adjustment (called from libphy)
|
|
|
|
*/
|
|
|
|
void (*adjust_link)(struct dsa_switch *ds, int port,
|
|
|
|
struct phy_device *phydev);
|
2014-08-28 04:04:54 +04:00
|
|
|
void (*fixed_link_update)(struct dsa_switch *ds, int port,
|
|
|
|
struct fixed_phy_status *st);
|
2014-08-28 04:04:53 +04:00
|
|
|
|
2011-11-27 21:06:08 +04:00
|
|
|
/*
|
|
|
|
* ethtool hardware statistics.
|
|
|
|
*/
|
|
|
|
void (*get_strings)(struct dsa_switch *ds, int port, uint8_t *data);
|
|
|
|
void (*get_ethtool_stats)(struct dsa_switch *ds,
|
|
|
|
int port, uint64_t *data);
|
|
|
|
int (*get_sset_count)(struct dsa_switch *ds);
|
2014-09-19 04:31:22 +04:00
|
|
|
|
2014-09-19 04:31:24 +04:00
|
|
|
/*
|
|
|
|
* ethtool Wake-on-LAN
|
|
|
|
*/
|
|
|
|
void (*get_wol)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_wolinfo *w);
|
|
|
|
int (*set_wol)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_wolinfo *w);
|
|
|
|
|
2014-09-19 04:31:22 +04:00
|
|
|
/*
|
|
|
|
* Suspend and resume
|
|
|
|
*/
|
|
|
|
int (*suspend)(struct dsa_switch *ds);
|
|
|
|
int (*resume)(struct dsa_switch *ds);
|
2014-09-25 04:05:18 +04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Port enable/disable
|
|
|
|
*/
|
|
|
|
int (*port_enable)(struct dsa_switch *ds, int port,
|
|
|
|
struct phy_device *phy);
|
|
|
|
void (*port_disable)(struct dsa_switch *ds, int port,
|
|
|
|
struct phy_device *phy);
|
2014-09-25 04:05:21 +04:00
|
|
|
|
|
|
|
/*
|
2017-08-01 23:32:41 +03:00
|
|
|
* Port's MAC EEE settings
|
2014-09-25 04:05:21 +04:00
|
|
|
*/
|
2017-08-01 23:32:41 +03:00
|
|
|
int (*set_mac_eee)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_eee *e);
|
|
|
|
int (*get_mac_eee)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_eee *e);
|
2014-10-29 20:44:58 +03:00
|
|
|
|
2014-10-29 20:45:01 +03:00
|
|
|
/* EEPROM access */
|
|
|
|
int (*get_eeprom_len)(struct dsa_switch *ds);
|
|
|
|
int (*get_eeprom)(struct dsa_switch *ds,
|
|
|
|
struct ethtool_eeprom *eeprom, u8 *data);
|
|
|
|
int (*set_eeprom)(struct dsa_switch *ds,
|
|
|
|
struct ethtool_eeprom *eeprom, u8 *data);
|
2014-10-29 20:45:04 +03:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Register access.
|
|
|
|
*/
|
|
|
|
int (*get_regs_len)(struct dsa_switch *ds, int port);
|
|
|
|
void (*get_regs)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_regs *regs, void *p);
|
2015-02-25 00:15:33 +03:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Bridge integration
|
|
|
|
*/
|
2016-07-19 03:45:38 +03:00
|
|
|
int (*set_ageing_time)(struct dsa_switch *ds, unsigned int msecs);
|
2016-03-13 23:21:32 +03:00
|
|
|
int (*port_bridge_join)(struct dsa_switch *ds, int port,
|
2016-02-12 20:09:39 +03:00
|
|
|
struct net_device *bridge);
|
2017-01-27 23:29:41 +03:00
|
|
|
void (*port_bridge_leave)(struct dsa_switch *ds, int port,
|
|
|
|
struct net_device *bridge);
|
2016-04-06 18:55:03 +03:00
|
|
|
void (*port_stp_state_set)(struct dsa_switch *ds, int port,
|
|
|
|
u8 state);
|
2016-09-22 23:49:22 +03:00
|
|
|
void (*port_fast_age)(struct dsa_switch *ds, int port);
|
2015-08-10 16:09:49 +03:00
|
|
|
|
2015-08-13 19:52:17 +03:00
|
|
|
/*
|
|
|
|
* VLAN support
|
|
|
|
*/
|
2016-02-26 21:16:00 +03:00
|
|
|
int (*port_vlan_filtering)(struct dsa_switch *ds, int port,
|
|
|
|
bool vlan_filtering);
|
2015-11-01 20:33:55 +03:00
|
|
|
int (*port_vlan_prepare)(struct dsa_switch *ds, int port,
|
|
|
|
const struct switchdev_obj_port_vlan *vlan,
|
|
|
|
struct switchdev_trans *trans);
|
2016-04-06 18:55:05 +03:00
|
|
|
void (*port_vlan_add)(struct dsa_switch *ds, int port,
|
2015-11-01 20:33:55 +03:00
|
|
|
const struct switchdev_obj_port_vlan *vlan,
|
|
|
|
struct switchdev_trans *trans);
|
|
|
|
int (*port_vlan_del)(struct dsa_switch *ds, int port,
|
|
|
|
const struct switchdev_obj_port_vlan *vlan);
|
2015-08-10 16:09:49 +03:00
|
|
|
/*
|
|
|
|
* Forwarding database
|
|
|
|
*/
|
2017-08-06 16:15:40 +03:00
|
|
|
int (*port_fdb_add)(struct dsa_switch *ds, int port,
|
2017-08-06 16:15:39 +03:00
|
|
|
const unsigned char *addr, u16 vid);
|
2015-08-10 16:09:49 +03:00
|
|
|
int (*port_fdb_del)(struct dsa_switch *ds, int port,
|
2017-08-06 16:15:39 +03:00
|
|
|
const unsigned char *addr, u16 vid);
|
2015-10-22 16:34:38 +03:00
|
|
|
int (*port_fdb_dump)(struct dsa_switch *ds, int port,
|
2017-08-06 16:15:49 +03:00
|
|
|
dsa_fdb_dump_cb_t *cb, void *data);
|
2016-08-31 18:50:03 +03:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Multicast database
|
|
|
|
*/
|
|
|
|
int (*port_mdb_prepare)(struct dsa_switch *ds, int port,
|
|
|
|
const struct switchdev_obj_port_mdb *mdb,
|
|
|
|
struct switchdev_trans *trans);
|
|
|
|
void (*port_mdb_add)(struct dsa_switch *ds, int port,
|
|
|
|
const struct switchdev_obj_port_mdb *mdb,
|
|
|
|
struct switchdev_trans *trans);
|
|
|
|
int (*port_mdb_del)(struct dsa_switch *ds, int port,
|
|
|
|
const struct switchdev_obj_port_mdb *mdb);
|
2017-01-30 20:48:40 +03:00
|
|
|
/*
|
|
|
|
* RXNFC
|
|
|
|
*/
|
|
|
|
int (*get_rxnfc)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_rxnfc *nfc, u32 *rule_locs);
|
|
|
|
int (*set_rxnfc)(struct dsa_switch *ds, int port,
|
|
|
|
struct ethtool_rxnfc *nfc);
|
2017-01-30 23:41:40 +03:00
|
|
|
|
|
|
|
/*
|
|
|
|
* TC integration
|
|
|
|
*/
|
|
|
|
int (*port_mirror_add)(struct dsa_switch *ds, int port,
|
|
|
|
struct dsa_mall_mirror_tc_entry *mirror,
|
|
|
|
bool ingress);
|
|
|
|
void (*port_mirror_del)(struct dsa_switch *ds, int port,
|
|
|
|
struct dsa_mall_mirror_tc_entry *mirror);
|
2017-03-31 00:37:14 +03:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Cross-chip operations
|
|
|
|
*/
|
|
|
|
int (*crosschip_bridge_join)(struct dsa_switch *ds, int sw_index,
|
|
|
|
int port, struct net_device *br);
|
|
|
|
void (*crosschip_bridge_leave)(struct dsa_switch *ds, int sw_index,
|
|
|
|
int port, struct net_device *br);
|
2011-11-27 21:06:08 +04:00
|
|
|
};
|
|
|
|
|
2017-01-09 01:52:07 +03:00
|
|
|
struct dsa_switch_driver {
|
|
|
|
struct list_head list;
|
2017-01-09 01:52:08 +03:00
|
|
|
const struct dsa_switch_ops *ops;
|
2017-01-09 01:52:07 +03:00
|
|
|
};
|
|
|
|
|
2017-04-12 19:45:03 +03:00
|
|
|
/* Legacy driver registration */
|
2017-01-09 01:52:07 +03:00
|
|
|
void register_switch_driver(struct dsa_switch_driver *type);
|
|
|
|
void unregister_switch_driver(struct dsa_switch_driver *type);
|
2014-09-15 21:00:27 +04:00
|
|
|
struct mii_bus *dsa_host_dev_to_mii_bus(struct device *dev);
|
2017-04-12 19:45:03 +03:00
|
|
|
|
2017-02-05 00:02:42 +03:00
|
|
|
struct net_device *dsa_dev_to_net_device(struct device *dev);
|
2011-11-27 21:06:08 +04:00
|
|
|
|
2017-06-01 23:07:11 +03:00
|
|
|
/* Keep inline for faster access in hot path */
|
2017-03-29 00:45:06 +03:00
|
|
|
static inline bool netdev_uses_dsa(struct net_device *dev)
|
|
|
|
{
|
|
|
|
#if IS_ENABLED(CONFIG_NET_DSA)
|
2017-06-01 23:07:13 +03:00
|
|
|
return dev->dsa_ptr && dev->dsa_ptr->rcv;
|
2017-03-29 00:45:06 +03:00
|
|
|
#endif
|
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
2017-01-27 23:29:36 +03:00
|
|
|
struct dsa_switch *dsa_switch_alloc(struct device *dev, size_t n);
|
2016-06-04 22:17:07 +03:00
|
|
|
void dsa_unregister_switch(struct dsa_switch *ds);
|
2017-05-27 01:12:51 +03:00
|
|
|
int dsa_register_switch(struct dsa_switch *ds);
|
2016-08-19 01:30:12 +03:00
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
|
|
int dsa_switch_suspend(struct dsa_switch *ds);
|
|
|
|
int dsa_switch_resume(struct dsa_switch *ds);
|
|
|
|
#else
|
|
|
|
static inline int dsa_switch_suspend(struct dsa_switch *ds)
|
|
|
|
{
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
static inline int dsa_switch_resume(struct dsa_switch *ds)
|
|
|
|
{
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
#endif /* CONFIG_PM_SLEEP */
|
|
|
|
|
2017-10-11 20:57:48 +03:00
|
|
|
enum dsa_notifier_type {
|
|
|
|
DSA_PORT_REGISTER,
|
|
|
|
DSA_PORT_UNREGISTER,
|
|
|
|
};
|
|
|
|
|
|
|
|
struct dsa_notifier_info {
|
|
|
|
struct net_device *dev;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct dsa_notifier_register_info {
|
|
|
|
struct dsa_notifier_info info; /* must be first */
|
|
|
|
struct net_device *master;
|
|
|
|
unsigned int port_number;
|
|
|
|
unsigned int switch_number;
|
|
|
|
};
|
|
|
|
|
|
|
|
static inline struct net_device *
|
|
|
|
dsa_notifier_info_to_dev(const struct dsa_notifier_info *info)
|
|
|
|
{
|
|
|
|
return info->dev;
|
|
|
|
}
|
|
|
|
|
|
|
|
#if IS_ENABLED(CONFIG_NET_DSA)
|
|
|
|
int register_dsa_notifier(struct notifier_block *nb);
|
|
|
|
int unregister_dsa_notifier(struct notifier_block *nb);
|
|
|
|
int call_dsa_notifiers(unsigned long val, struct net_device *dev,
|
|
|
|
struct dsa_notifier_info *info);
|
|
|
|
#else
|
|
|
|
static inline int register_dsa_notifier(struct notifier_block *nb)
|
|
|
|
{
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline int unregister_dsa_notifier(struct notifier_block *nb)
|
|
|
|
{
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline int call_dsa_notifiers(unsigned long val, struct net_device *dev,
|
|
|
|
struct dsa_notifier_info *info)
|
|
|
|
{
|
|
|
|
return NOTIFY_DONE;
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
2017-10-11 20:57:49 +03:00
|
|
|
/* Broadcom tag specific helpers to insert and extract queue/port number */
|
|
|
|
#define BRCM_TAG_SET_PORT_QUEUE(p, q) ((p) << 8 | q)
|
|
|
|
#define BRCM_TAG_GET_PORT(v) ((v) >> 8)
|
|
|
|
#define BRCM_TAG_GET_QUEUE(v) ((v) & 0xff)
|
|
|
|
|
net: Distributed Switch Architecture protocol support
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
|
|
|
#endif
|