microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/drivers/phy/tegra/Makefile

11 строки
485 B
Makefile
Исходник Обычный вид История

treewide: Add SPDX license identifier - Makefile/Kconfig Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-19 15:07:45 +03:00
# SPDX-License-Identifier: GPL-2.0-only
phy: Add Tegra XUSB pad controller support Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs. This hardware block used to be exposed as a pin controller, but it turns out that this isn't a good fit. The new driver and DT binding much more accurately describe the hardware and are more flexible in supporting new SoC generations. Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-11 20:24:21 +03:00
obj-$(CONFIG_PHY_TEGRA_XUSB) += phy-tegra-xusb.o
phy-tegra-xusb-y += xusb.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
phy: tegra: Add Tegra210 support Add support for the XUSB pad controller found on Tegra210 SoCs. The hardware is roughly the same, but some of the registers have been moved around and the number and type of supported pads has changed. Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-11 20:25:02 +03:00
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o
phy: tegra: xusb: Add Tegra186 support Add support for the XUSB pad controller found on Tegra186 SoCs. It is mostly similar to the same IP found on earlier chips, but the number of pads exposed differs, as do the programming sequences. Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power supplies of the XUSB pad controller require strict power sequencing and are therefore controlled by the PMIC on Tegra186. Signed-off-by: JC Kuo <jckuo@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> [dan.carpenter@oracle.com: Fix testing the wrong variable in probe()] Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> [yuehaibing@huawei.com: Make two functions static to fix sparse warning] Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-02-21 18:46:34 +03:00
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_186_SOC) += xusb-tegra186.o
phy: tegra: xusb: Add Tegra194 support Add support for the XUSB pad controller found on Tegra194 SoCs. It is mostly similar to the same IP found on Tegra186, but the number of pads exposed differs, as do the programming sequences. Because most of the Tegra194 XUSB PADCTL registers definition and programming sequence are the same as Tegra186, Tegra194 XUSB PADCTL can share the same driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL. Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it is possible for some platforms have long signal trace that could not provide sufficient electrical environment for Gen 2 speed. This patch adds a "maximum-speed" property to usb3 ports which can be used to specify the maximum supported speed for any particular USB 3.1 port. For a port that is not capable of SuperSpeedPlus, "maximum-speed" property should carry "super-speed". Signed-off-by: JC Kuo <jckuo@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2020-02-12 09:11:30 +03:00
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_194_SOC) += xusb-tegra186.o
phy: tegra: Add PCIe PIPE2UPHY support Synopsys DesignWare core based PCIe controllers in Tegra 194 SoC interface with Universal PHY (UPHY) module through a PIPE2UPHY (P2U) module. For each PCIe lane of a controller, there is a P2U unit instantiated at hardware level. This driver provides support for the programming required for each P2U that is going to be used for a PCIe controller. Signed-off-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Thierry Reding <treding@nvidia.com>
2019-08-13 14:36:26 +03:00
obj-$(CONFIG_PHY_TEGRA194_P2U) += phy-tegra194-p2u.o