WSL2-Linux-Kernel/arch/x86/mm/numa_32.c

60 строки
1.9 KiB
C
Исходник Обычный вид История

/*
* Written by: Patricia Gaughen <gone@us.ibm.com>, IBM Corporation
* August 2002: added remote node KVA remap - Martin J. Bligh
*
* Copyright (C) 2002, IBM Corp.
*
* All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
* NON INFRINGEMENT. See the GNU General Public License for more
* details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/memblock.h>
#include <linux/init.h>
#include "numa_internal.h"
extern unsigned long highend_pfn, highstart_pfn;
void __init initmem_init(void)
{
x86_numa_init();
x86-32, numa: Move lowmem address space reservation to init_alloc_remap() Remap alloc init is done in the following stages. 1. init_alloc_remap() calculates how much memory is necessary for each node and reserves node local memory. 2. initmem_init() collects how much each node needs and reserves a single contiguous lowmem area which can contain all. 3. init_remap_allocator() initializes allocator parameters from the determined lowmem address and per-node offsets. 4. Actual remap happens. There is no reason for the lowmem remap area to be reserved as a single contiguous area at one go. They don't interact with each other and the memblock allocator will put them side-by-side anyway. This patch breaks up the single lowmem address reservation and put per-node lowmem address reservation into init_alloc_remap() and initializes allocator parameters directly in the function as all the addresses are determined there. This merges steps 2 and 3 into 1. While at it, remove now largely irrelevant comments in init_alloc_remap(). This change causes the following behavior changes. * Remap lowmem areas are allocated in smaller per-node chunks. * Remap lowmem area reservation failure fail future remap allocations instead of panicking. * Remap allocator initialization is less verbose. Signed-off-by: Tejun Heo <tj@kernel.org> Link: http://lkml.kernel.org/r/1301955840-7246-10-git-send-email-tj@kernel.org Acked-by: Yinghai Lu <yinghai@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
2011-04-05 02:23:55 +04:00
#ifdef CONFIG_HIGHMEM
highstart_pfn = highend_pfn = max_pfn;
if (max_pfn > max_low_pfn)
highstart_pfn = max_low_pfn;
printk(KERN_NOTICE "%ldMB HIGHMEM available.\n",
pages_to_mb(highend_pfn - highstart_pfn));
high_memory = (void *) __va(highstart_pfn * PAGE_SIZE - 1) + 1;
#else
high_memory = (void *) __va(max_low_pfn * PAGE_SIZE - 1) + 1;
#endif
printk(KERN_NOTICE "%ldMB LOWMEM available.\n",
pages_to_mb(max_low_pfn));
printk(KERN_DEBUG "max_low_pfn = %lx, highstart_pfn = %lx\n",
max_low_pfn, highstart_pfn);
printk(KERN_DEBUG "Low memory ends at vaddr %08lx\n",
(ulong) pfn_to_kaddr(max_low_pfn));
printk(KERN_DEBUG "High memory starts at vaddr %08lx\n",
(ulong) pfn_to_kaddr(highstart_pfn));
__vmalloc_start_set = true;
setup_bootmem_allocator();
}