81 строка
2.1 KiB
Plaintext
81 строка
2.1 KiB
Plaintext
|
Sound Blaster 16X Vibra addendum
|
||
|
--------------------------------
|
||
|
by Marius Ilioaea <mariusi@protv.ro>
|
||
|
Stefan Laudat <stefan@asit.ro>
|
||
|
|
||
|
Sat Mar 6 23:55:27 EET 1999
|
||
|
|
||
|
Hello again,
|
||
|
|
||
|
Playing with a SB Vibra 16x soundcard we found it very difficult
|
||
|
to setup because the kernel reported a lot of DMA errors and wouldn't
|
||
|
simply play any sound.
|
||
|
A good starting point is that the vibra16x chip full-duplex facility
|
||
|
is neither still exploited by the sb driver found in the linux kernel
|
||
|
(tried it with a 2.2.2-ac7), nor in the commercial OSS package (it reports
|
||
|
it as half-duplex soundcard). Oh, I almost forgot, the RedHat sndconfig
|
||
|
failed detecting it ;)
|
||
|
So, the big problem still remains, because the sb module wants a
|
||
|
8-bit and a 16-bit dma, which we could not allocate for vibra... it supports
|
||
|
only two 8-bit dma channels, the second one will be passed to the module
|
||
|
as a 16 bit channel, the kernel will yield about that but everything will
|
||
|
be okay, trust us.
|
||
|
The only inconvenient you may find is that you will have
|
||
|
some sound playing jitters if you have HDD dma support enabled - but this
|
||
|
will happen with almost all soundcards...
|
||
|
|
||
|
A fully working isapnp.conf is just here:
|
||
|
|
||
|
<snip here>
|
||
|
|
||
|
(READPORT 0x0203)
|
||
|
(ISOLATE PRESERVE)
|
||
|
(IDENTIFY *)
|
||
|
(VERBOSITY 2)
|
||
|
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
|
||
|
# SB 16 and OPL3 devices
|
||
|
(CONFIGURE CTL00f0/-1 (LD 0
|
||
|
(INT 0 (IRQ 5 (MODE +E)))
|
||
|
(DMA 0 (CHANNEL 1))
|
||
|
(DMA 1 (CHANNEL 3))
|
||
|
(IO 0 (SIZE 16) (BASE 0x0220))
|
||
|
(IO 2 (SIZE 4) (BASE 0x0388))
|
||
|
(NAME "CTL00f0/-1[0]{Audio }")
|
||
|
(ACT Y)
|
||
|
))
|
||
|
|
||
|
# Joystick device - only if you need it :-/
|
||
|
|
||
|
(CONFIGURE CTL00f0/-1 (LD 1
|
||
|
(IO 0 (SIZE 1) (BASE 0x0200))
|
||
|
(NAME "CTL00f0/-1[1]{Game }")
|
||
|
(ACT Y)
|
||
|
))
|
||
|
(WAITFORKEY)
|
||
|
|
||
|
<end of snipping>
|
||
|
|
||
|
So, after a good kernel modules compilation and a 'depmod -a kernel_ver'
|
||
|
you may want to:
|
||
|
|
||
|
modprobe sb io=0x220 irq=5 dma=1 dma16=3
|
||
|
|
||
|
Or, take the hard way:
|
||
|
|
||
|
modprobe soundcore
|
||
|
modprobe sound
|
||
|
modprobe uart401
|
||
|
modprobe sb io=0x220 irq=5 dma=1 dma16=3
|
||
|
# do you need MIDI?
|
||
|
modprobe opl3=0x388
|
||
|
|
||
|
Just in case, the kernel sound support should be:
|
||
|
|
||
|
CONFIG_SOUND=m
|
||
|
CONFIG_SOUND_OSS=m
|
||
|
CONFIG_SOUND_SB=m
|
||
|
|
||
|
Enjoy your new noisy Linux box! ;)
|
||
|
|
||
|
|