WSL2-Linux-Kernel/arch/powerpc/include/asm/keylargo.h

#ifndef _ASM_POWERPC_KEYLARGO_H
#define _ASM_POWERPC_KEYLARGO_H
#ifdef __KERNEL__
/*
 * keylargo.h: definitions for using the "KeyLargo" I/O controller chip.
 *
 */

/* "Pangea" chipset has keylargo device-id 0x25 while core99
 * has device-id 0x22. The rev. of the pangea one is 0, so we
 * fake an artificial rev. in keylargo_rev by oring 0x100
 */
#define KL_PANGEA_REV		0x100

/* offset from base for feature control registers */
#define KEYLARGO_MBCR		0x34	/* KL Only, Media bay control/status */
#define KEYLARGO_FCR0		0x38
#define KEYLARGO_FCR1		0x3c
#define KEYLARGO_FCR2		0x40
#define KEYLARGO_FCR3		0x44
#define KEYLARGO_FCR4		0x48
#define KEYLARGO_FCR5		0x4c	/* Pangea only */

/* K2 aditional FCRs */
#define K2_FCR6			0x34
#define K2_FCR7			0x30
#define K2_FCR8			0x2c
#define K2_FCR9			0x28
#define K2_FCR10		0x24

/* GPIO registers */
#define KEYLARGO_GPIO_LEVELS0		0x50
#define KEYLARGO_GPIO_LEVELS1		0x54
#define KEYLARGO_GPIO_EXTINT_0		0x58
#define KEYLARGO_GPIO_EXTINT_CNT	18
#define KEYLARGO_GPIO_0			0x6A
#define KEYLARGO_GPIO_CNT		17
#define KEYLARGO_GPIO_EXTINT_DUAL_EDGE	0x80
#define KEYLARGO_GPIO_OUTPUT_ENABLE	0x04
#define KEYLARGO_GPIO_OUTOUT_DATA	0x01
#define KEYLARGO_GPIO_INPUT_DATA	0x02

/* K2 does only extint GPIOs and does 51 of them */
#define K2_GPIO_EXTINT_0		0x58
#define K2_GPIO_EXTINT_CNT		51

/* Specific GPIO regs */

#define KL_GPIO_MODEM_RESET		(KEYLARGO_GPIO_0+0x03)
#define KL_GPIO_MODEM_POWER		(KEYLARGO_GPIO_0+0x02) /* Pangea */

#define KL_GPIO_SOUND_POWER		(KEYLARGO_GPIO_0+0x05)

/* Hrm... this one is only to be used on Pismo. It seeem to also
 * control the timebase enable on other machines. Still to be
 * experimented... --BenH.
 */
#define KL_GPIO_FW_CABLE_POWER		(KEYLARGO_GPIO_0+0x09)
#define KL_GPIO_TB_ENABLE		(KEYLARGO_GPIO_0+0x09)

#define KL_GPIO_ETH_PHY_RESET		(KEYLARGO_GPIO_0+0x10)

#define KL_GPIO_EXTINT_CPU1		(KEYLARGO_GPIO_0+0x0a)
#define KL_GPIO_EXTINT_CPU1_ASSERT	0x04
#define KL_GPIO_EXTINT_CPU1_RELEASE	0x38

#define KL_GPIO_RESET_CPU0		(KEYLARGO_GPIO_EXTINT_0+0x03)
#define KL_GPIO_RESET_CPU1		(KEYLARGO_GPIO_EXTINT_0+0x04)
#define KL_GPIO_RESET_CPU2		(KEYLARGO_GPIO_EXTINT_0+0x0f)
#define KL_GPIO_RESET_CPU3		(KEYLARGO_GPIO_EXTINT_0+0x10)

#define KL_GPIO_PMU_MESSAGE_IRQ		(KEYLARGO_GPIO_EXTINT_0+0x09)
#define KL_GPIO_PMU_MESSAGE_BIT		KEYLARGO_GPIO_INPUT_DATA

#define KL_GPIO_MEDIABAY_IRQ		(KEYLARGO_GPIO_EXTINT_0+0x0e)

#define KL_GPIO_AIRPORT_0		(KEYLARGO_GPIO_EXTINT_0+0x0a)
#define KL_GPIO_AIRPORT_1		(KEYLARGO_GPIO_EXTINT_0+0x0d)
#define KL_GPIO_AIRPORT_2		(KEYLARGO_GPIO_0+0x0d)
#define KL_GPIO_AIRPORT_3		(KEYLARGO_GPIO_0+0x0e)
#define KL_GPIO_AIRPORT_4		(KEYLARGO_GPIO_0+0x0f)

/*
 * Bits in feature control register. Those bits different for K2 are
 * listed separately
 */
#define KL_MBCR_MB0_PCI_ENABLE		0x00000800	/* exist ? */
#define KL_MBCR_MB0_IDE_ENABLE		0x00001000
#define KL_MBCR_MB0_FLOPPY_ENABLE	0x00002000	/* exist ? */
#define KL_MBCR_MB0_SOUND_ENABLE	0x00004000	/* hrm... */
#define KL_MBCR_MB0_DEV_MASK		0x00007800
#define KL_MBCR_MB0_DEV_POWER		0x00000400
#define KL_MBCR_MB0_DEV_RESET		0x00000200
#define KL_MBCR_MB0_ENABLE		0x00000100
#define KL_MBCR_MB1_PCI_ENABLE		0x08000000	/* exist ? */
#define KL_MBCR_MB1_IDE_ENABLE		0x10000000
#define KL_MBCR_MB1_FLOPPY_ENABLE	0x20000000	/* exist ? */
#define KL_MBCR_MB1_SOUND_ENABLE	0x40000000	/* hrm... */
#define KL_MBCR_MB1_DEV_MASK		0x78000000
#define KL_MBCR_MB1_DEV_POWER		0x04000000
#define KL_MBCR_MB1_DEV_RESET		0x02000000
#define KL_MBCR_MB1_ENABLE		0x01000000

#define KL0_SCC_B_INTF_ENABLE		0x00000001	/* (KL Only) */
#define KL0_SCC_A_INTF_ENABLE		0x00000002
#define KL0_SCC_SLOWPCLK		0x00000004
#define KL0_SCC_RESET			0x00000008
#define KL0_SCCA_ENABLE			0x00000010
#define KL0_SCCB_ENABLE			0x00000020
#define KL0_SCC_CELL_ENABLE		0x00000040
#define KL0_IRDA_HIGH_BAND		0x00000100	/* (KL Only) */
#define KL0_IRDA_SOURCE2_SEL		0x00000200	/* (KL Only) */
#define KL0_IRDA_SOURCE1_SEL		0x00000400	/* (KL Only) */
#define KL0_PG_USB0_PMI_ENABLE		0x00000400	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_RESET			0x00000800	/* (KL Only) */
#define KL0_PG_USB0_REF_SUSPEND_SEL	0x00000800	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_DEFAULT1		0x00001000	/* (KL Only) */
#define KL0_PG_USB0_REF_SUSPEND		0x00001000	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_DEFAULT0		0x00002000	/* (KL Only) */
#define KL0_PG_USB0_PAD_SUSPEND		0x00002000	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_FAST_CONNECT		0x00004000	/* (KL Only) */
#define KL0_PG_USB1_PMI_ENABLE		0x00004000	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_ENABLE			0x00008000	/* (KL Only) */
#define KL0_PG_USB1_REF_SUSPEND_SEL	0x00008000	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_CLK32_ENABLE		0x00010000	/* (KL Only) */
#define KL0_PG_USB1_REF_SUSPEND		0x00010000	/* (Pangea/Intrepid Only) */
#define KL0_IRDA_CLK19_ENABLE		0x00020000	/* (KL Only) */
#define KL0_PG_USB1_PAD_SUSPEND		0x00020000	/* (Pangea/Intrepid Only) */
#define KL0_USB0_PAD_SUSPEND0		0x00040000
#define KL0_USB0_PAD_SUSPEND1		0x00080000
#define KL0_USB0_CELL_ENABLE		0x00100000
#define KL0_USB1_PAD_SUSPEND0		0x00400000
#define KL0_USB1_PAD_SUSPEND1		0x00800000
#define KL0_USB1_CELL_ENABLE		0x01000000
#define KL0_USB_REF_SUSPEND		0x10000000	/* (KL Only) */

#define KL0_SERIAL_ENABLE		(KL0_SCC_B_INTF_ENABLE | \
					KL0_SCC_SLOWPCLK | \
					KL0_SCC_CELL_ENABLE | KL0_SCCA_ENABLE)

#define KL1_USB2_PMI_ENABLE		0x00000001	/* Intrepid only */
#define KL1_AUDIO_SEL_22MCLK		0x00000002	/* KL/Pangea only */
#define KL1_USB2_REF_SUSPEND_SEL	0x00000002	/* Intrepid only */
#define KL1_USB2_REF_SUSPEND		0x00000004	/* Intrepid only */
#define KL1_AUDIO_CLK_ENABLE_BIT	0x00000008	/* KL/Pangea only */
#define KL1_USB2_PAD_SUSPEND_SEL	0x00000008	/* Intrepid only */
#define KL1_USB2_PAD_SUSPEND0		0x00000010	/* Intrepid only */
#define KL1_AUDIO_CLK_OUT_ENABLE	0x00000020	/* KL/Pangea only */
#define KL1_USB2_PAD_SUSPEND1		0x00000020	/* Intrepid only */
#define KL1_AUDIO_CELL_ENABLE		0x00000040	/* KL/Pangea only */
#define KL1_USB2_CELL_ENABLE		0x00000040	/* Intrepid only */
#define KL1_AUDIO_CHOOSE		0x00000080	/* KL/Pangea only */
#define KL1_I2S0_CHOOSE			0x00000200	/* KL Only */
#define KL1_I2S0_CELL_ENABLE		0x00000400
#define KL1_I2S0_CLK_ENABLE_BIT		0x00001000
#define KL1_I2S0_ENABLE			0x00002000
#define KL1_I2S1_CELL_ENABLE		0x00020000
#define KL1_I2S1_CLK_ENABLE_BIT		0x00080000
#define KL1_I2S1_ENABLE			0x00100000
#define KL1_EIDE0_ENABLE		0x00800000	/* KL/Intrepid Only */
#define KL1_EIDE0_RESET_N		0x01000000	/* KL/Intrepid Only */
#define KL1_EIDE1_ENABLE		0x04000000	/* KL Only */
#define KL1_EIDE1_RESET_N		0x08000000	/* KL Only */
#define KL1_UIDE_ENABLE			0x20000000	/* KL/Pangea Only */
#define KL1_UIDE_RESET_N		0x40000000	/* KL/Pangea Only */

#define KL2_IOBUS_ENABLE		0x00000002
#define KL2_SLEEP_STATE_BIT		0x00000100	/* KL Only */
#define KL2_PG_STOP_ALL_CLOCKS		0x00000100	/* Pangea Only */
#define KL2_MPIC_ENABLE			0x00020000
#define KL2_CARDSLOT_RESET		0x00040000	/* Pangea/Intrepid Only */
#define KL2_ALT_DATA_OUT		0x02000000	/* KL Only ??? */
#define KL2_MEM_IS_BIG			0x04000000
#define KL2_CARDSEL_16			0x08000000

#define KL3_SHUTDOWN_PLL_TOTAL		0x00000001	/* KL/Pangea only */
#define KL3_SHUTDOWN_PLLKW6		0x00000002	/* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL3		0x00000002	/* Intrepid only */
#define KL3_SHUTDOWN_PLLKW4		0x00000004	/* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL2		0x00000004	/* Intrepid only */
#define KL3_SHUTDOWN_PLLKW35		0x00000008	/* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL1		0x00000008	/* Intrepid only */
#define KL3_SHUTDOWN_PLLKW12		0x00000010	/* KL Only */
#define KL3_IT_ENABLE_PLL3_SHUTDOWN	0x00000010	/* Intrepid only */
#define KL3_PLL_RESET			0x00000020	/* KL/Pangea only */
#define KL3_IT_ENABLE_PLL2_SHUTDOWN	0x00000020	/* Intrepid only */
#define KL3_IT_ENABLE_PLL1_SHUTDOWN	0x00000010	/* Intrepid only */
#define KL3_SHUTDOWN_PLL2X		0x00000080	/* KL Only */
#define KL3_CLK66_ENABLE		0x00000100	/* KL Only */
#define KL3_CLK49_ENABLE		0x00000200
#define KL3_CLK45_ENABLE		0x00000400
#define KL3_CLK31_ENABLE		0x00000800	/* KL/Pangea only */
#define KL3_TIMER_CLK18_ENABLE		0x00001000
#define KL3_I2S1_CLK18_ENABLE		0x00002000
#define KL3_I2S0_CLK18_ENABLE		0x00004000
#define KL3_VIA_CLK16_ENABLE		0x00008000	/* KL/Pangea only */
#define KL3_IT_VIA_CLK32_ENABLE		0x00008000	/* Intrepid only */
#define KL3_STOPPING33_ENABLED		0x00080000	/* KL Only */
#define KL3_PG_PLL_ENABLE_TEST		0x00080000	/* Pangea Only */

/* Intrepid USB bus 2, port 0,1 */
#define KL3_IT_PORT_WAKEUP_ENABLE(p)		(0x00080000 << ((p)<<3))
#define KL3_IT_PORT_RESUME_WAKE_EN(p)		(0x00040000 << ((p)<<3))
#define KL3_IT_PORT_CONNECT_WAKE_EN(p)		(0x00020000 << ((p)<<3))
#define KL3_IT_PORT_DISCONNECT_WAKE_EN(p)	(0x00010000 << ((p)<<3))
#define KL3_IT_PORT_RESUME_STAT(p)		(0x00300000 << ((p)<<3))
#define KL3_IT_PORT_CONNECT_STAT(p)		(0x00200000 << ((p)<<3))
#define KL3_IT_PORT_DISCONNECT_STAT(p)		(0x00100000 << ((p)<<3))

/* Port 0,1 : bus 0, port 2,3 : bus 1 */
#define KL4_PORT_WAKEUP_ENABLE(p)	(0x00000008 << ((p)<<3))
#define KL4_PORT_RESUME_WAKE_EN(p)	(0x00000004 << ((p)<<3))
#define KL4_PORT_CONNECT_WAKE_EN(p)	(0x00000002 << ((p)<<3))
#define KL4_PORT_DISCONNECT_WAKE_EN(p)	(0x00000001 << ((p)<<3))
#define KL4_PORT_RESUME_STAT(p)		(0x00000040 << ((p)<<3))
#define KL4_PORT_CONNECT_STAT(p)	(0x00000020 << ((p)<<3))
#define KL4_PORT_DISCONNECT_STAT(p)	(0x00000010 << ((p)<<3))

/* Pangea and Intrepid only */
#define KL5_VIA_USE_CLK31		0000000001	/* Pangea Only */
#define KL5_SCC_USE_CLK31		0x00000002	/* Pangea Only */
#define KL5_PWM_CLK32_EN		0x00000004
#define KL5_CLK3_68_EN			0x00000010
#define KL5_CLK32_EN			0x00000020


/* K2 definitions */
#define K2_FCR0_USB0_SWRESET		0x00200000
#define K2_FCR0_USB1_SWRESET		0x02000000
#define K2_FCR0_RING_PME_DISABLE	0x08000000

#define K2_FCR1_PCI1_BUS_RESET_N	0x00000010
#define K2_FCR1_PCI1_SLEEP_RESET_EN	0x00000020
#define K2_FCR1_I2S0_CELL_ENABLE	0x00000400
#define K2_FCR1_I2S0_RESET		0x00000800
#define K2_FCR1_I2S0_CLK_ENABLE_BIT	0x00001000
#define K2_FCR1_I2S0_ENABLE    		0x00002000
#define K2_FCR1_PCI1_CLK_ENABLE		0x00004000
#define K2_FCR1_FW_CLK_ENABLE		0x00008000
#define K2_FCR1_FW_RESET_N		0x00010000
#define K2_FCR1_I2S1_CELL_ENABLE	0x00020000
#define K2_FCR1_I2S1_CLK_ENABLE_BIT	0x00080000
#define K2_FCR1_I2S1_ENABLE		0x00100000
#define K2_FCR1_GMAC_CLK_ENABLE		0x00400000
#define K2_FCR1_GMAC_POWER_DOWN		0x00800000
#define K2_FCR1_GMAC_RESET_N		0x01000000
#define K2_FCR1_SATA_CLK_ENABLE		0x02000000
#define K2_FCR1_SATA_POWER_DOWN		0x04000000
#define K2_FCR1_SATA_RESET_N		0x08000000
#define K2_FCR1_UATA_CLK_ENABLE		0x10000000
#define K2_FCR1_UATA_RESET_N		0x40000000
#define K2_FCR1_UATA_CHOOSE_CLK66	0x80000000

/* Shasta definitions */
#define SH_FCR1_I2S2_CELL_ENABLE	0x00000010
#define SH_FCR1_I2S2_CLK_ENABLE_BIT	0x00000040
#define SH_FCR1_I2S2_ENABLE		0x00000080
#define SH_FCR3_I2S2_CLK18_ENABLE	0x00008000

#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_KEYLARGO_H */
[PATCH] powerpc: sanitize header files for user space includes include/asm-ppc/ had #ifdef __KERNEL__ in all header files that are not meant for use by user space, include/asm-powerpc does not have this yet. This patch gets us a lot closer there. There are a few cases where I was not sure, so I left them out. I have verified that no CONFIG_* symbols are used outside of __KERNEL__ any more and that there are no obvious compile errors when including any of the headers in user space libraries. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org> 2005-12-17 00:43:46 +03:00			`#ifndef _ASM_POWERPC_KEYLARGO_H`
			`#define _ASM_POWERPC_KEYLARGO_H`
			`#ifdef __KERNEL__`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`/*`
			`* keylargo.h: definitions for using the "KeyLargo" I/O controller chip.`
			`*`
			`*/`

			`/* "Pangea" chipset has keylargo device-id 0x25 while core99`
			`* has device-id 0x22. The rev. of the pangea one is 0, so we`
			`* fake an artificial rev. in keylargo_rev by oring 0x100`
			`*/`
			`#define KL_PANGEA_REV 0x100`

			`/* offset from base for feature control registers */`
			`#define KEYLARGO_MBCR 0x34 /* KL Only, Media bay control/status */`
			`#define KEYLARGO_FCR0 0x38`
			`#define KEYLARGO_FCR1 0x3c`
			`#define KEYLARGO_FCR2 0x40`
			`#define KEYLARGO_FCR3 0x44`
			`#define KEYLARGO_FCR4 0x48`
			`#define KEYLARGO_FCR5 0x4c /* Pangea only */`

			`/* K2 aditional FCRs */`
			`#define K2_FCR6 0x34`
			`#define K2_FCR7 0x30`
			`#define K2_FCR8 0x2c`
			`#define K2_FCR9 0x28`
			`#define K2_FCR10 0x24`

			`/* GPIO registers */`
			`#define KEYLARGO_GPIO_LEVELS0 0x50`
			`#define KEYLARGO_GPIO_LEVELS1 0x54`
			`#define KEYLARGO_GPIO_EXTINT_0 0x58`
			`#define KEYLARGO_GPIO_EXTINT_CNT 18`
			`#define KEYLARGO_GPIO_0 0x6A`
			`#define KEYLARGO_GPIO_CNT 17`
			`#define KEYLARGO_GPIO_EXTINT_DUAL_EDGE 0x80`
			`#define KEYLARGO_GPIO_OUTPUT_ENABLE 0x04`
			`#define KEYLARGO_GPIO_OUTOUT_DATA 0x01`
			`#define KEYLARGO_GPIO_INPUT_DATA 0x02`

			`/* K2 does only extint GPIOs and does 51 of them */`
			`#define K2_GPIO_EXTINT_0 0x58`
			`#define K2_GPIO_EXTINT_CNT 51`

			`/* Specific GPIO regs */`

			`#define KL_GPIO_MODEM_RESET (KEYLARGO_GPIO_0+0x03)`
			`#define KL_GPIO_MODEM_POWER (KEYLARGO_GPIO_0+0x02) /* Pangea */`

			`#define KL_GPIO_SOUND_POWER (KEYLARGO_GPIO_0+0x05)`

			`/* Hrm... this one is only to be used on Pismo. It seeem to also`
			`* control the timebase enable on other machines. Still to be`
			`* experimented... --BenH.`
			`*/`
			`#define KL_GPIO_FW_CABLE_POWER (KEYLARGO_GPIO_0+0x09)`
			`#define KL_GPIO_TB_ENABLE (KEYLARGO_GPIO_0+0x09)`

			`#define KL_GPIO_ETH_PHY_RESET (KEYLARGO_GPIO_0+0x10)`

			`#define KL_GPIO_EXTINT_CPU1 (KEYLARGO_GPIO_0+0x0a)`
			`#define KL_GPIO_EXTINT_CPU1_ASSERT 0x04`
			`#define KL_GPIO_EXTINT_CPU1_RELEASE 0x38`

			`#define KL_GPIO_RESET_CPU0 (KEYLARGO_GPIO_EXTINT_0+0x03)`
			`#define KL_GPIO_RESET_CPU1 (KEYLARGO_GPIO_EXTINT_0+0x04)`
			`#define KL_GPIO_RESET_CPU2 (KEYLARGO_GPIO_EXTINT_0+0x0f)`
			`#define KL_GPIO_RESET_CPU3 (KEYLARGO_GPIO_EXTINT_0+0x10)`

			`#define KL_GPIO_PMU_MESSAGE_IRQ (KEYLARGO_GPIO_EXTINT_0+0x09)`
			`#define KL_GPIO_PMU_MESSAGE_BIT KEYLARGO_GPIO_INPUT_DATA`

			`#define KL_GPIO_MEDIABAY_IRQ (KEYLARGO_GPIO_EXTINT_0+0x0e)`

			`#define KL_GPIO_AIRPORT_0 (KEYLARGO_GPIO_EXTINT_0+0x0a)`
			`#define KL_GPIO_AIRPORT_1 (KEYLARGO_GPIO_EXTINT_0+0x0d)`
			`#define KL_GPIO_AIRPORT_2 (KEYLARGO_GPIO_0+0x0d)`
			`#define KL_GPIO_AIRPORT_3 (KEYLARGO_GPIO_0+0x0e)`
			`#define KL_GPIO_AIRPORT_4 (KEYLARGO_GPIO_0+0x0f)`

			`/*`
			`* Bits in feature control register. Those bits different for K2 are`
			`* listed separately`
			`*/`
			`#define KL_MBCR_MB0_PCI_ENABLE 0x00000800 /* exist ? */`
			`#define KL_MBCR_MB0_IDE_ENABLE 0x00001000`
			`#define KL_MBCR_MB0_FLOPPY_ENABLE 0x00002000 /* exist ? */`
			`#define KL_MBCR_MB0_SOUND_ENABLE 0x00004000 /* hrm... */`
			`#define KL_MBCR_MB0_DEV_MASK 0x00007800`
			`#define KL_MBCR_MB0_DEV_POWER 0x00000400`
			`#define KL_MBCR_MB0_DEV_RESET 0x00000200`
			`#define KL_MBCR_MB0_ENABLE 0x00000100`
			`#define KL_MBCR_MB1_PCI_ENABLE 0x08000000 /* exist ? */`
			`#define KL_MBCR_MB1_IDE_ENABLE 0x10000000`
			`#define KL_MBCR_MB1_FLOPPY_ENABLE 0x20000000 /* exist ? */`
			`#define KL_MBCR_MB1_SOUND_ENABLE 0x40000000 /* hrm... */`
			`#define KL_MBCR_MB1_DEV_MASK 0x78000000`
			`#define KL_MBCR_MB1_DEV_POWER 0x04000000`
			`#define KL_MBCR_MB1_DEV_RESET 0x02000000`
			`#define KL_MBCR_MB1_ENABLE 0x01000000`

			`#define KL0_SCC_B_INTF_ENABLE 0x00000001 /* (KL Only) */`
			`#define KL0_SCC_A_INTF_ENABLE 0x00000002`
			`#define KL0_SCC_SLOWPCLK 0x00000004`
			`#define KL0_SCC_RESET 0x00000008`
			`#define KL0_SCCA_ENABLE 0x00000010`
			`#define KL0_SCCB_ENABLE 0x00000020`
			`#define KL0_SCC_CELL_ENABLE 0x00000040`
			`#define KL0_IRDA_HIGH_BAND 0x00000100 /* (KL Only) */`
			`#define KL0_IRDA_SOURCE2_SEL 0x00000200 /* (KL Only) */`
			`#define KL0_IRDA_SOURCE1_SEL 0x00000400 /* (KL Only) */`
			`#define KL0_PG_USB0_PMI_ENABLE 0x00000400 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_RESET 0x00000800 /* (KL Only) */`
			`#define KL0_PG_USB0_REF_SUSPEND_SEL 0x00000800 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_DEFAULT1 0x00001000 /* (KL Only) */`
			`#define KL0_PG_USB0_REF_SUSPEND 0x00001000 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_DEFAULT0 0x00002000 /* (KL Only) */`
			`#define KL0_PG_USB0_PAD_SUSPEND 0x00002000 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_FAST_CONNECT 0x00004000 /* (KL Only) */`
			`#define KL0_PG_USB1_PMI_ENABLE 0x00004000 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_ENABLE 0x00008000 /* (KL Only) */`
			`#define KL0_PG_USB1_REF_SUSPEND_SEL 0x00008000 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_CLK32_ENABLE 0x00010000 /* (KL Only) */`
			`#define KL0_PG_USB1_REF_SUSPEND 0x00010000 /* (Pangea/Intrepid Only) */`
			`#define KL0_IRDA_CLK19_ENABLE 0x00020000 /* (KL Only) */`
			`#define KL0_PG_USB1_PAD_SUSPEND 0x00020000 /* (Pangea/Intrepid Only) */`
			`#define KL0_USB0_PAD_SUSPEND0 0x00040000`
			`#define KL0_USB0_PAD_SUSPEND1 0x00080000`
			`#define KL0_USB0_CELL_ENABLE 0x00100000`
			`#define KL0_USB1_PAD_SUSPEND0 0x00400000`
			`#define KL0_USB1_PAD_SUSPEND1 0x00800000`
			`#define KL0_USB1_CELL_ENABLE 0x01000000`
			`#define KL0_USB_REF_SUSPEND 0x10000000 /* (KL Only) */`

			`#define KL0_SERIAL_ENABLE (KL0_SCC_B_INTF_ENABLE \| \`
			`KL0_SCC_SLOWPCLK \| \`
			`KL0_SCC_CELL_ENABLE \| KL0_SCCA_ENABLE)`

			`#define KL1_USB2_PMI_ENABLE 0x00000001 /* Intrepid only */`
			`#define KL1_AUDIO_SEL_22MCLK 0x00000002 /* KL/Pangea only */`
			`#define KL1_USB2_REF_SUSPEND_SEL 0x00000002 /* Intrepid only */`
			`#define KL1_USB2_REF_SUSPEND 0x00000004 /* Intrepid only */`
			`#define KL1_AUDIO_CLK_ENABLE_BIT 0x00000008 /* KL/Pangea only */`
			`#define KL1_USB2_PAD_SUSPEND_SEL 0x00000008 /* Intrepid only */`
			`#define KL1_USB2_PAD_SUSPEND0 0x00000010 /* Intrepid only */`
			`#define KL1_AUDIO_CLK_OUT_ENABLE 0x00000020 /* KL/Pangea only */`
			`#define KL1_USB2_PAD_SUSPEND1 0x00000020 /* Intrepid only */`
			`#define KL1_AUDIO_CELL_ENABLE 0x00000040 /* KL/Pangea only */`
			`#define KL1_USB2_CELL_ENABLE 0x00000040 /* Intrepid only */`
			`#define KL1_AUDIO_CHOOSE 0x00000080 /* KL/Pangea only */`
			`#define KL1_I2S0_CHOOSE 0x00000200 /* KL Only */`
			`#define KL1_I2S0_CELL_ENABLE 0x00000400`
			`#define KL1_I2S0_CLK_ENABLE_BIT 0x00001000`
			`#define KL1_I2S0_ENABLE 0x00002000`
			`#define KL1_I2S1_CELL_ENABLE 0x00020000`
			`#define KL1_I2S1_CLK_ENABLE_BIT 0x00080000`
			`#define KL1_I2S1_ENABLE 0x00100000`
			`#define KL1_EIDE0_ENABLE 0x00800000 /* KL/Intrepid Only */`
			`#define KL1_EIDE0_RESET_N 0x01000000 /* KL/Intrepid Only */`
			`#define KL1_EIDE1_ENABLE 0x04000000 /* KL Only */`
			`#define KL1_EIDE1_RESET_N 0x08000000 /* KL Only */`
			`#define KL1_UIDE_ENABLE 0x20000000 /* KL/Pangea Only */`
			`#define KL1_UIDE_RESET_N 0x40000000 /* KL/Pangea Only */`

			`#define KL2_IOBUS_ENABLE 0x00000002`
			`#define KL2_SLEEP_STATE_BIT 0x00000100 /* KL Only */`
			`#define KL2_PG_STOP_ALL_CLOCKS 0x00000100 /* Pangea Only */`
			`#define KL2_MPIC_ENABLE 0x00020000`
			`#define KL2_CARDSLOT_RESET 0x00040000 /* Pangea/Intrepid Only */`
			`#define KL2_ALT_DATA_OUT 0x02000000 /* KL Only ??? */`
			`#define KL2_MEM_IS_BIG 0x04000000`
			`#define KL2_CARDSEL_16 0x08000000`

			`#define KL3_SHUTDOWN_PLL_TOTAL 0x00000001 /* KL/Pangea only */`
			`#define KL3_SHUTDOWN_PLLKW6 0x00000002 /* KL/Pangea only */`
			`#define KL3_IT_SHUTDOWN_PLL3 0x00000002 /* Intrepid only */`
			`#define KL3_SHUTDOWN_PLLKW4 0x00000004 /* KL/Pangea only */`
			`#define KL3_IT_SHUTDOWN_PLL2 0x00000004 /* Intrepid only */`
			`#define KL3_SHUTDOWN_PLLKW35 0x00000008 /* KL/Pangea only */`
			`#define KL3_IT_SHUTDOWN_PLL1 0x00000008 /* Intrepid only */`
			`#define KL3_SHUTDOWN_PLLKW12 0x00000010 /* KL Only */`
			`#define KL3_IT_ENABLE_PLL3_SHUTDOWN 0x00000010 /* Intrepid only */`
			`#define KL3_PLL_RESET 0x00000020 /* KL/Pangea only */`
			`#define KL3_IT_ENABLE_PLL2_SHUTDOWN 0x00000020 /* Intrepid only */`
			`#define KL3_IT_ENABLE_PLL1_SHUTDOWN 0x00000010 /* Intrepid only */`
			`#define KL3_SHUTDOWN_PLL2X 0x00000080 /* KL Only */`
			`#define KL3_CLK66_ENABLE 0x00000100 /* KL Only */`
			`#define KL3_CLK49_ENABLE 0x00000200`
			`#define KL3_CLK45_ENABLE 0x00000400`
			`#define KL3_CLK31_ENABLE 0x00000800 /* KL/Pangea only */`
			`#define KL3_TIMER_CLK18_ENABLE 0x00001000`
			`#define KL3_I2S1_CLK18_ENABLE 0x00002000`
			`#define KL3_I2S0_CLK18_ENABLE 0x00004000`
			`#define KL3_VIA_CLK16_ENABLE 0x00008000 /* KL/Pangea only */`
			`#define KL3_IT_VIA_CLK32_ENABLE 0x00008000 /* Intrepid only */`
			`#define KL3_STOPPING33_ENABLED 0x00080000 /* KL Only */`
			`#define KL3_PG_PLL_ENABLE_TEST 0x00080000 /* Pangea Only */`

			`/* Intrepid USB bus 2, port 0,1 */`
			`#define KL3_IT_PORT_WAKEUP_ENABLE(p) (0x00080000 << ((p)<<3))`
			`#define KL3_IT_PORT_RESUME_WAKE_EN(p) (0x00040000 << ((p)<<3))`
			`#define KL3_IT_PORT_CONNECT_WAKE_EN(p) (0x00020000 << ((p)<<3))`
			`#define KL3_IT_PORT_DISCONNECT_WAKE_EN(p) (0x00010000 << ((p)<<3))`
			`#define KL3_IT_PORT_RESUME_STAT(p) (0x00300000 << ((p)<<3))`
			`#define KL3_IT_PORT_CONNECT_STAT(p) (0x00200000 << ((p)<<3))`
			`#define KL3_IT_PORT_DISCONNECT_STAT(p) (0x00100000 << ((p)<<3))`

			`/* Port 0,1 : bus 0, port 2,3 : bus 1 */`
			`#define KL4_PORT_WAKEUP_ENABLE(p) (0x00000008 << ((p)<<3))`
			`#define KL4_PORT_RESUME_WAKE_EN(p) (0x00000004 << ((p)<<3))`
			`#define KL4_PORT_CONNECT_WAKE_EN(p) (0x00000002 << ((p)<<3))`
			`#define KL4_PORT_DISCONNECT_WAKE_EN(p) (0x00000001 << ((p)<<3))`
			`#define KL4_PORT_RESUME_STAT(p) (0x00000040 << ((p)<<3))`
			`#define KL4_PORT_CONNECT_STAT(p) (0x00000020 << ((p)<<3))`
			`#define KL4_PORT_DISCONNECT_STAT(p) (0x00000010 << ((p)<<3))`

			`/* Pangea and Intrepid only */`
			`#define KL5_VIA_USE_CLK31 0000000001 /* Pangea Only */`
			`#define KL5_SCC_USE_CLK31 0x00000002 /* Pangea Only */`
			`#define KL5_PWM_CLK32_EN 0x00000004`
			`#define KL5_CLK3_68_EN 0x00000010`
			`#define KL5_CLK32_EN 0x00000020`


			`/* K2 definitions */`
			`#define K2_FCR0_USB0_SWRESET 0x00200000`
			`#define K2_FCR0_USB1_SWRESET 0x02000000`
			`#define K2_FCR0_RING_PME_DISABLE 0x08000000`

			`#define K2_FCR1_PCI1_BUS_RESET_N 0x00000010`
			`#define K2_FCR1_PCI1_SLEEP_RESET_EN 0x00000020`
[PATCH] ppc64: very basic desktop g5 sound support This patch hacks the current PowerMac Alsa driver to add some basic support of analog sound output to some desktop G5s. It has severe limitations though: - Only 44100Khz 16 bits - Only work on G5 models using a TAS3004 analog code, that is early single CPU desktops and all dual CPU desktops at this date, but none of the more recent ones like iMac G5. - It does analog only, no digital/SPDIF support at all, no native AC3 support Better support would require a complete rewrite of the driver (which I am working on, but don't hold your breath), to properly support the diversity of apple sound HW setup, including dual codecs, several i2s busses, all the new codecs used in the new machines, proper clock switching with digital, etc etc etc... This patch applies on top of the other PowerMac sound patches I posted in the past couple of days (new powerbook support and sleep fixes). Note: This is a FAQ entry for PowerMac sound support with TI codecs: They have a feature called "DRC" which is automatically enabled for the internal speaker (at least when auto mute control is enabled) which will cause your sound to fade out to nothing after half a second of playback if you don't set a proper "DRC Range" in the mixer. So if you have a problem like that, check alsamixer and raise your DRC Range to something reasonable. Note2: This patch will also add auto-mute of the speaker when line-out jack is used on some earlier desktop G4s (and on the G5) in addition to the headphone jack. If that behaviour isn't what you want, just disable auto-muting and use the manual mute controls in alsamixer. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org> 2005-04-17 02:24:32 +04:00			`#define K2_FCR1_I2S0_CELL_ENABLE 0x00000400`
			`#define K2_FCR1_I2S0_RESET 0x00000800`
			`#define K2_FCR1_I2S0_CLK_ENABLE_BIT 0x00001000`
			`#define K2_FCR1_I2S0_ENABLE 0x00002000`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`#define K2_FCR1_PCI1_CLK_ENABLE 0x00004000`
			`#define K2_FCR1_FW_CLK_ENABLE 0x00008000`
			`#define K2_FCR1_FW_RESET_N 0x00010000`
[PATCH] powerpc: Remove device_node addrs/n_addr The pre-parsed addrs/n_addrs fields in struct device_node are finally gone. Remove the dodgy heuristics that did that parsing at boot and remove the fields themselves since we now have a good replacement with the new OF parsing code. This patch also fixes a bunch of drivers to use the new code instead, so that at least pmac32, pseries, iseries and g5 defconfigs build. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org> 2005-12-13 10:01:21 +03:00			`#define K2_FCR1_I2S1_CELL_ENABLE 0x00020000`
			`#define K2_FCR1_I2S1_CLK_ENABLE_BIT 0x00080000`
			`#define K2_FCR1_I2S1_ENABLE 0x00100000`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`#define K2_FCR1_GMAC_CLK_ENABLE 0x00400000`
			`#define K2_FCR1_GMAC_POWER_DOWN 0x00800000`
			`#define K2_FCR1_GMAC_RESET_N 0x01000000`
			`#define K2_FCR1_SATA_CLK_ENABLE 0x02000000`
			`#define K2_FCR1_SATA_POWER_DOWN 0x04000000`
			`#define K2_FCR1_SATA_RESET_N 0x08000000`
			`#define K2_FCR1_UATA_CLK_ENABLE 0x10000000`
			`#define K2_FCR1_UATA_RESET_N 0x40000000`
			`#define K2_FCR1_UATA_CHOOSE_CLK66 0x80000000`

[PATCH] powerpc: Remove device_node addrs/n_addr The pre-parsed addrs/n_addrs fields in struct device_node are finally gone. Remove the dodgy heuristics that did that parsing at boot and remove the fields themselves since we now have a good replacement with the new OF parsing code. This patch also fixes a bunch of drivers to use the new code instead, so that at least pmac32, pseries, iseries and g5 defconfigs build. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org> 2005-12-13 10:01:21 +03:00			`/* Shasta definitions */`
			`#define SH_FCR1_I2S2_CELL_ENABLE 0x00000010`
			`#define SH_FCR1_I2S2_CLK_ENABLE_BIT 0x00000040`
			`#define SH_FCR1_I2S2_ENABLE 0x00000080`
			`#define SH_FCR3_I2S2_CLK18_ENABLE 0x00008000`

[PATCH] powerpc: sanitize header files for user space includes include/asm-ppc/ had #ifdef __KERNEL__ in all header files that are not meant for use by user space, include/asm-powerpc does not have this yet. This patch gets us a lot closer there. There are a few cases where I was not sure, so I left them out. I have verified that no CONFIG_* symbols are used outside of __KERNEL__ any more and that there are no obvious compile errors when including any of the headers in user space libraries. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org> 2005-12-17 00:43:46 +03:00			`#endif /* __KERNEL__ */`
			`#endif /* _ASM_POWERPC_KEYLARGO_H */`