WSL2-Linux-Kernel/net/mac80211/ieee80211_i.h

1266 строки
36 KiB
C
Исходник Обычный вид История

/*
* Copyright 2002-2005, Instant802 Networks, Inc.
* Copyright 2005, Devicescape Software, Inc.
* Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
* Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef IEEE80211_I_H
#define IEEE80211_I_H
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/if_ether.h>
#include <linux/interrupt.h>
#include <linux/list.h>
#include <linux/netdevice.h>
#include <linux/skbuff.h>
#include <linux/workqueue.h>
#include <linux/types.h>
#include <linux/spinlock.h>
#include <linux/etherdevice.h>
#include <net/ieee80211_radiotap.h>
#include <net/cfg80211.h>
#include <net/mac80211.h>
#include "key.h"
#include "sta_info.h"
struct ieee80211_local;
/* Maximum number of broadcast/multicast frames to buffer when some of the
* associated stations are using power saving. */
#define AP_MAX_BC_BUFFER 128
/* Maximum number of frames buffered to all STAs, including multicast frames.
* Note: increasing this limit increases the potential memory requirement. Each
* frame can be up to about 2 kB long. */
#define TOTAL_MAX_TX_BUFFER 512
/* Required encryption head and tailroom */
#define IEEE80211_ENCRYPT_HEADROOM 8
#define IEEE80211_ENCRYPT_TAILROOM 18
/* IEEE 802.11 (Ch. 9.5 Defragmentation) requires support for concurrent
* reception of at least three fragmented frames. This limit can be increased
* by changing this define, at the cost of slower frame reassembly and
* increased memory use (about 2 kB of RAM per entry). */
#define IEEE80211_FRAGMENT_MAX 4
/*
* Time after which we ignore scan results and no longer report/use
* them in any way.
*/
#define IEEE80211_SCAN_RESULT_EXPIRE (10 * HZ)
#define TU_TO_EXP_TIME(x) (jiffies + usecs_to_jiffies((x) * 1024))
#define IEEE80211_DEFAULT_UAPSD_QUEUES \
(IEEE80211_WMM_IE_STA_QOSINFO_AC_BK | \
IEEE80211_WMM_IE_STA_QOSINFO_AC_BE | \
IEEE80211_WMM_IE_STA_QOSINFO_AC_VI | \
IEEE80211_WMM_IE_STA_QOSINFO_AC_VO)
#define IEEE80211_DEFAULT_MAX_SP_LEN \
IEEE80211_WMM_IE_STA_QOSINFO_SP_ALL
struct ieee80211_fragment_entry {
unsigned long first_frag_time;
unsigned int seq;
unsigned int rx_queue;
unsigned int last_frag;
unsigned int extra_len;
struct sk_buff_head skb_list;
int ccmp; /* Whether fragments were encrypted with CCMP */
u8 last_pn[6]; /* PN of the last fragment if CCMP was used */
};
struct ieee80211_bss {
/* don't want to look up all the time */
size_t ssid_len;
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 dtim_period;
bool wmm_used;
bool uapsd_supported;
unsigned long last_probe_resp;
#ifdef CONFIG_MAC80211_MESH
u8 *mesh_id;
size_t mesh_id_len;
u8 *mesh_cfg;
#endif
#define IEEE80211_MAX_SUPP_RATES 32
u8 supp_rates[IEEE80211_MAX_SUPP_RATES];
size_t supp_rates_len;
/*
* During assocation, we save an ERP value from a probe response so
* that we can feed ERP info to the driver when handling the
* association completes. these fields probably won't be up-to-date
* otherwise, you probably don't want to use them.
*/
bool has_erp_value;
u8 erp_value;
};
static inline u8 *bss_mesh_cfg(struct ieee80211_bss *bss)
{
#ifdef CONFIG_MAC80211_MESH
return bss->mesh_cfg;
#endif
return NULL;
}
static inline u8 *bss_mesh_id(struct ieee80211_bss *bss)
{
#ifdef CONFIG_MAC80211_MESH
return bss->mesh_id;
#endif
return NULL;
}
static inline u8 bss_mesh_id_len(struct ieee80211_bss *bss)
{
#ifdef CONFIG_MAC80211_MESH
return bss->mesh_id_len;
#endif
return 0;
}
typedef unsigned __bitwise__ ieee80211_tx_result;
#define TX_CONTINUE ((__force ieee80211_tx_result) 0u)
#define TX_DROP ((__force ieee80211_tx_result) 1u)
#define TX_QUEUED ((__force ieee80211_tx_result) 2u)
#define IEEE80211_TX_FRAGMENTED BIT(0)
#define IEEE80211_TX_UNICAST BIT(1)
#define IEEE80211_TX_PS_BUFFERED BIT(2)
struct ieee80211_tx_data {
struct sk_buff *skb;
struct ieee80211_local *local;
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
struct ieee80211_key *key;
struct ieee80211_channel *channel;
u16 ethertype;
unsigned int flags;
};
typedef unsigned __bitwise__ ieee80211_rx_result;
#define RX_CONTINUE ((__force ieee80211_rx_result) 0u)
#define RX_DROP_UNUSABLE ((__force ieee80211_rx_result) 1u)
#define RX_DROP_MONITOR ((__force ieee80211_rx_result) 2u)
#define RX_QUEUED ((__force ieee80211_rx_result) 3u)
#define IEEE80211_RX_IN_SCAN BIT(0)
/* frame is destined to interface currently processed (incl. multicast frames) */
#define IEEE80211_RX_RA_MATCH BIT(1)
#define IEEE80211_RX_AMSDU BIT(2)
#define IEEE80211_RX_FRAGMENTED BIT(3)
/* only add flags here that do not change with subframes of an aMPDU */
struct ieee80211_rx_data {
struct sk_buff *skb;
struct ieee80211_local *local;
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
struct ieee80211_key *key;
unsigned int flags;
int queue;
u32 tkip_iv32;
u16 tkip_iv16;
};
struct beacon_data {
u8 *head, *tail;
int head_len, tail_len;
int dtim_period;
};
struct ieee80211_if_ap {
struct beacon_data *beacon;
struct list_head vlans;
/* yes, this looks ugly, but guarantees that we can later use
* bitmap_empty :)
* NB: don't touch this bitmap, use sta_info_{set,clear}_tim_bit */
u8 tim[sizeof(unsigned long) * BITS_TO_LONGS(IEEE80211_MAX_AID + 1)];
struct sk_buff_head ps_bc_buf;
atomic_t num_sta_ps; /* number of stations in PS mode */
int dtim_count;
};
struct ieee80211_if_wds {
struct sta_info *sta;
u8 remote_addr[ETH_ALEN];
};
struct ieee80211_if_vlan {
struct list_head list;
/* used for all tx if the VLAN is configured to 4-addr mode */
struct sta_info *sta;
};
struct mesh_stats {
__u32 fwded_mcast; /* Mesh forwarded multicast frames */
__u32 fwded_unicast; /* Mesh forwarded unicast frames */
__u32 fwded_frames; /* Mesh total forwarded frames */
__u32 dropped_frames_ttl; /* Not transmitted since mesh_ttl == 0*/
__u32 dropped_frames_no_route; /* Not transmitted, no route found */
atomic_t estab_plinks;
};
#define PREQ_Q_F_START 0x1
#define PREQ_Q_F_REFRESH 0x2
struct mesh_preq_queue {
struct list_head list;
u8 dst[ETH_ALEN];
u8 flags;
};
enum ieee80211_work_type {
IEEE80211_WORK_ABORT,
IEEE80211_WORK_DIRECT_PROBE,
IEEE80211_WORK_AUTH,
IEEE80211_WORK_ASSOC_BEACON_WAIT,
IEEE80211_WORK_ASSOC,
IEEE80211_WORK_REMAIN_ON_CHANNEL,
};
/**
* enum work_done_result - indicates what to do after work was done
*
* @WORK_DONE_DESTROY: This work item is no longer needed, destroy.
* @WORK_DONE_REQUEUE: This work item was reset to be reused, and
* should be requeued.
*/
enum work_done_result {
WORK_DONE_DESTROY,
WORK_DONE_REQUEUE,
};
struct ieee80211_work {
struct list_head list;
struct rcu_head rcu_head;
struct ieee80211_sub_if_data *sdata;
enum work_done_result (*done)(struct ieee80211_work *wk,
struct sk_buff *skb);
struct ieee80211_channel *chan;
enum nl80211_channel_type chan_type;
unsigned long timeout;
enum ieee80211_work_type type;
u8 filter_ta[ETH_ALEN];
bool started;
union {
struct {
int tries;
u16 algorithm, transaction;
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 ssid_len;
u8 key[WLAN_KEY_LEN_WEP104];
u8 key_len, key_idx;
bool privacy;
} probe_auth;
struct {
struct cfg80211_bss *bss;
const u8 *supp_rates;
const u8 *ht_information_ie;
enum ieee80211_smps_mode smps;
int tries;
u16 capability;
u8 prev_bssid[ETH_ALEN];
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 ssid_len;
u8 supp_rates_len;
bool wmm_used, use_11n, uapsd_used;
} assoc;
struct {
u32 duration;
} remain;
};
int ie_len;
/* must be last */
u8 ie[0];
};
/* flags used in struct ieee80211_if_managed.flags */
enum ieee80211_sta_flags {
IEEE80211_STA_BEACON_POLL = BIT(0),
IEEE80211_STA_CONNECTION_POLL = BIT(1),
IEEE80211_STA_CONTROL_PORT = BIT(2),
IEEE80211_STA_DISABLE_11N = BIT(4),
IEEE80211_STA_CSA_RECEIVED = BIT(5),
IEEE80211_STA_MFP_ENABLED = BIT(6),
IEEE80211_STA_UAPSD_ENABLED = BIT(7),
IEEE80211_STA_NULLFUNC_ACKED = BIT(8),
IEEE80211_STA_RESET_SIGNAL_AVE = BIT(9),
};
struct ieee80211_if_managed {
struct timer_list timer;
struct timer_list conn_mon_timer;
struct timer_list bcn_mon_timer;
struct timer_list chswitch_timer;
struct work_struct monitor_work;
struct work_struct chswitch_work;
struct work_struct beacon_connection_loss_work;
unsigned long probe_timeout;
int probe_send_count;
struct mutex mtx;
struct cfg80211_bss *associated;
u8 bssid[ETH_ALEN];
u16 aid;
unsigned long timers_running; /* used for quiesce/restart */
bool powersave; /* powersave requested for this iface */
enum ieee80211_smps_mode req_smps, /* requested smps mode */
ap_smps; /* smps mode AP thinks we're in */
unsigned int flags;
u32 beacon_crc;
enum {
IEEE80211_MFP_DISABLED,
IEEE80211_MFP_OPTIONAL,
IEEE80211_MFP_REQUIRED
} mfp; /* management frame protection */
int wmm_last_param_set;
u8 use_4addr;
/* Signal strength from the last Beacon frame in the current BSS. */
int last_beacon_signal;
/*
* Weighted average of the signal strength from Beacon frames in the
* current BSS. This is in units of 1/16 of the signal unit to maintain
* accuracy and to speed up calculations, i.e., the value need to be
* divided by 16 to get the actual value.
*/
int ave_beacon_signal;
/*
* Last Beacon frame signal strength average (ave_beacon_signal / 16)
* that triggered a cqm event. 0 indicates that no event has been
* generated for the current association.
*/
int last_cqm_event_signal;
};
struct ieee80211_if_ibss {
struct timer_list timer;
struct mutex mtx;
unsigned long last_scan_completed;
u32 basic_rates;
bool timer_running;
bool fixed_bssid;
bool fixed_channel;
bool privacy;
u8 bssid[ETH_ALEN];
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 ssid_len, ie_len;
u8 *ie;
struct ieee80211_channel *channel;
unsigned long ibss_join_req;
/* probe response/beacon for IBSS */
struct sk_buff *presp, *skb;
enum {
IEEE80211_IBSS_MLME_SEARCH,
IEEE80211_IBSS_MLME_JOINED,
} state;
};
struct ieee80211_if_mesh {
struct timer_list housekeeping_timer;
struct timer_list mesh_path_timer;
struct timer_list mesh_path_root_timer;
unsigned long timers_running;
unsigned long wrkq_flags;
u8 mesh_id[IEEE80211_MAX_MESH_ID_LEN];
size_t mesh_id_len;
/* Active Path Selection Protocol Identifier */
u8 mesh_pp_id;
/* Active Path Selection Metric Identifier */
u8 mesh_pm_id;
/* Congestion Control Mode Identifier */
u8 mesh_cc_id;
/* Synchronization Protocol Identifier */
u8 mesh_sp_id;
/* Authentication Protocol Identifier */
u8 mesh_auth_id;
/* Local mesh Sequence Number */
u32 sn;
/* Last used PREQ ID */
u32 preq_id;
atomic_t mpaths;
/* Timestamp of last SN update */
unsigned long last_sn_update;
/* Timestamp of last SN sent */
unsigned long last_preq;
struct mesh_rmc *rmc;
spinlock_t mesh_preq_queue_lock;
struct mesh_preq_queue preq_queue;
int preq_queue_len;
struct mesh_stats mshstats;
struct mesh_config mshcfg;
u32 mesh_seqnum;
bool accepting_plinks;
};
#ifdef CONFIG_MAC80211_MESH
#define IEEE80211_IFSTA_MESH_CTR_INC(msh, name) \
do { (msh)->mshstats.name++; } while (0)
#else
#define IEEE80211_IFSTA_MESH_CTR_INC(msh, name) \
do { } while (0)
#endif
/**
* enum ieee80211_sub_if_data_flags - virtual interface flags
*
* @IEEE80211_SDATA_ALLMULTI: interface wants all multicast packets
* @IEEE80211_SDATA_PROMISC: interface is promisc
* @IEEE80211_SDATA_OPERATING_GMODE: operating in G-only mode
* @IEEE80211_SDATA_DONT_BRIDGE_PACKETS: bridge packets between
* associated stations and deliver multicast frames both
* back to wireless media and to the local net stack.
*/
enum ieee80211_sub_if_data_flags {
IEEE80211_SDATA_ALLMULTI = BIT(0),
IEEE80211_SDATA_PROMISC = BIT(1),
IEEE80211_SDATA_OPERATING_GMODE = BIT(2),
IEEE80211_SDATA_DONT_BRIDGE_PACKETS = BIT(3),
};
struct ieee80211_sub_if_data {
struct list_head list;
struct wireless_dev wdev;
[MAC80211]: rework key handling This moves all the key handling code out from ieee80211_ioctl.c into key.c and also does the following changes including documentation updates in mac80211.h: 1) Turn off hardware acceleration for keys when the interface is down. This is necessary because otherwise monitor interfaces could be decrypting frames for other interfaces that are down at the moment. Also, it should go some way towards better suspend/resume support, in any case the routines used here could be used for that as well. Additionally, this makes the driver interface nicer, keys for a specific local MAC address are only ever present while an interface with that MAC address is enabled. 2) Change driver set_key() callback interface to allow only return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all other return values. This allows debugging the stack when a driver notices it's handed a key while it is down. 3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE. 4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we want to use it, we'll use DISABLE_KEY for each key. It is hard to use REMOVE_ALL_KEYS because we can handle multiple virtual interfaces with different key configuration, so we'd have to keep track of a lot of state for this and that isn't worth it. 5) Warn when disabling a key fails, it musn't. 6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself. 7) Tell driver that a (non-WEP) key is used only for transmission by using an all-zeroes station MAC address when configuring. 8) Change the set_key() callback to have access to the local MAC address the key is being added for. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-29 01:01:55 +04:00
/* keys */
struct list_head key_list;
struct net_device *dev;
struct ieee80211_local *local;
unsigned int flags;
int drop_unencrypted;
char name[IFNAMSIZ];
/*
* keep track of whether the HT opmode (stored in
* vif.bss_info.ht_operation_mode) is valid.
*/
bool ht_opmode_valid;
/* Fragment table for host-based reassembly */
struct ieee80211_fragment_entry fragments[IEEE80211_FRAGMENT_MAX];
unsigned int fragment_next;
#define NUM_DEFAULT_KEYS 4
#define NUM_DEFAULT_MGMT_KEYS 2
struct ieee80211_key *keys[NUM_DEFAULT_KEYS + NUM_DEFAULT_MGMT_KEYS];
struct ieee80211_key *default_key;
struct ieee80211_key *default_mgmt_key;
u16 sequence_number;
struct work_struct work;
struct sk_buff_head skb_queue;
mac80211: Fix circular locking dependency in ARP filter handling There is a circular locking dependency when configuring the hardware ARP filters on association, occurring when flushing the mac80211 workqueue. This is what happens: [ 92.026800] ======================================================= [ 92.030507] [ INFO: possible circular locking dependency detected ] [ 92.030507] 2.6.34-04781-g2b2c009 #85 [ 92.030507] ------------------------------------------------------- [ 92.030507] modprobe/5225 is trying to acquire lock: [ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq ueue+0x0/0xb0 [ 92.030507] [ 92.030507] but task is already holding lock: [ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20 [ 92.030507] [ 92.030507] which lock already depends on the new lock. [ 92.030507] [ 92.030507] [ 92.030507] the existing dependency chain (in reverse order) is: [ 92.030507] [ 92.030507] -> #2 (rtnl_mutex){+.+.+.}: [ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110 [ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300 [ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20 [ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211] [ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211] [ 92.030507] -> #1 ((&local->work_work)){+.+.+.}: [ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110 [ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370 [ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0 [ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10 [ 92.030507] [ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}: [ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50 [ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110 [ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0 [ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211] [ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211] The locking in this case is quite complex. Fix the problem by rewriting the way the hardware ARP filter list is handled - i.e. make a copy of the address list to the bss_conf struct, and provide that list to the hardware driver when needed. The current patch will enable filtering also in promiscuous mode. This may need to be changed in the future. Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-09 14:43:26 +04:00
bool arp_filter_state;
/*
* AP this belongs to: self in AP mode and
* corresponding AP in VLAN mode, NULL for
* all others (might be needed later in IBSS)
*/
struct ieee80211_if_ap *bss;
/* bitmap of allowed (non-MCS) rate indexes for rate control */
u32 rc_rateidx_mask[IEEE80211_NUM_BANDS];
union {
struct ieee80211_if_ap ap;
struct ieee80211_if_wds wds;
struct ieee80211_if_vlan vlan;
struct ieee80211_if_managed mgd;
struct ieee80211_if_ibss ibss;
#ifdef CONFIG_MAC80211_MESH
struct ieee80211_if_mesh mesh;
#endif
u32 mntr_flags;
} u;
#ifdef CONFIG_MAC80211_DEBUGFS
struct {
struct dentry *dir;
struct dentry *default_key;
struct dentry *default_mgmt_key;
} debugfs;
#endif
/* must be last, dynamically sized area in this! */
struct ieee80211_vif vif;
};
static inline
struct ieee80211_sub_if_data *vif_to_sdata(struct ieee80211_vif *p)
{
return container_of(p, struct ieee80211_sub_if_data, vif);
}
static inline void
ieee80211_sdata_set_mesh_id(struct ieee80211_sub_if_data *sdata,
u8 mesh_id_len, u8 *mesh_id)
{
#ifdef CONFIG_MAC80211_MESH
struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
ifmsh->mesh_id_len = mesh_id_len;
memcpy(ifmsh->mesh_id, mesh_id, mesh_id_len);
#else
WARN_ON(1);
#endif
}
enum sdata_queue_type {
IEEE80211_SDATA_QUEUE_TYPE_FRAME = 0,
IEEE80211_SDATA_QUEUE_AGG_START = 1,
IEEE80211_SDATA_QUEUE_AGG_STOP = 2,
};
enum {
IEEE80211_RX_MSG = 1,
IEEE80211_TX_STATUS_MSG = 2,
};
enum queue_stop_reason {
IEEE80211_QUEUE_STOP_REASON_DRIVER,
IEEE80211_QUEUE_STOP_REASON_PS,
mac80211: fix aggregation for hardware with ampdu queues Hardware with AMPDU queues currently has broken aggregation. This patch fixes it by making all A-MPDUs go over the regular AC queues, but keeping track of the hardware queues in mac80211. As a first rough version, it actually stops the AC queue for extended periods of time, which can be removed by adding buffering internal to mac80211, but is currently not a huge problem because people rarely use multiple TIDs that are in the same AC (and iwlwifi currently doesn't operate as AP). This is a short-term fix, my current medium-term plan, which I hope to execute soon as well, but am not sure can finish before .30, looks like this: 1) rework the internal queuing layer in mac80211 that we use for fragments if the driver stopped queue in the middle of a fragmented frame to be able to queue more frames at once (rather than just a single frame with its fragments) 2) instead of stopping the entire AC queue, queue up the frames in a per-station/per-TID queue during aggregation session initiation, when the session has come up take all those frames and put them onto the queue from 1) 3) push the ampdu queue layer abstraction this patch introduces in mac80211 into the driver, and remove the virtual queue stuff from mac80211 again This plan will probably also affect ath9k in that mac80211 queues the frames instead of passing them down, even when there are no ampdu queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-12 02:51:53 +03:00
IEEE80211_QUEUE_STOP_REASON_CSA,
IEEE80211_QUEUE_STOP_REASON_AGGREGATION,
IEEE80211_QUEUE_STOP_REASON_SUSPEND,
IEEE80211_QUEUE_STOP_REASON_SKB_ADD,
};
/**
* mac80211 scan flags - currently active scan mode
*
* @SCAN_SW_SCANNING: We're currently in the process of scanning but may as
* well be on the operating channel
* @SCAN_HW_SCANNING: The hardware is scanning for us, we have no way to
* determine if we are on the operating channel or not
* @SCAN_OFF_CHANNEL: We're off our operating channel for scanning,
* gets only set in conjunction with SCAN_SW_SCANNING
*/
enum {
SCAN_SW_SCANNING,
SCAN_HW_SCANNING,
SCAN_OFF_CHANNEL,
};
/**
* enum mac80211_scan_state - scan state machine states
*
* @SCAN_DECISION: Main entry point to the scan state machine, this state
* determines if we should keep on scanning or switch back to the
* operating channel
* @SCAN_SET_CHANNEL: Set the next channel to be scanned
* @SCAN_SEND_PROBE: Send probe requests and wait for probe responses
* @SCAN_LEAVE_OPER_CHANNEL: Leave the operating channel, notify the AP
* about us leaving the channel and stop all associated STA interfaces
* @SCAN_ENTER_OPER_CHANNEL: Enter the operating channel again, notify the
* AP about us being back and restart all associated STA interfaces
*/
enum mac80211_scan_state {
SCAN_DECISION,
SCAN_SET_CHANNEL,
SCAN_SEND_PROBE,
SCAN_LEAVE_OPER_CHANNEL,
SCAN_ENTER_OPER_CHANNEL,
};
struct ieee80211_local {
/* embed the driver visible part.
* don't cast (use the static inlines below), but we keep
* it first anyway so they become a no-op */
struct ieee80211_hw hw;
const struct ieee80211_ops *ops;
/*
* work stuff, potentially off-channel (in the future)
*/
struct mutex work_mtx;
struct list_head work_list;
struct timer_list work_timer;
struct work_struct work_work;
struct sk_buff_head work_skb_queue;
/*
* private workqueue to mac80211. mac80211 makes this accessible
* via ieee80211_queue_work()
*/
struct workqueue_struct *workqueue;
unsigned long queue_stop_reasons[IEEE80211_MAX_QUEUES];
mac80211: fix aggregation for hardware with ampdu queues Hardware with AMPDU queues currently has broken aggregation. This patch fixes it by making all A-MPDUs go over the regular AC queues, but keeping track of the hardware queues in mac80211. As a first rough version, it actually stops the AC queue for extended periods of time, which can be removed by adding buffering internal to mac80211, but is currently not a huge problem because people rarely use multiple TIDs that are in the same AC (and iwlwifi currently doesn't operate as AP). This is a short-term fix, my current medium-term plan, which I hope to execute soon as well, but am not sure can finish before .30, looks like this: 1) rework the internal queuing layer in mac80211 that we use for fragments if the driver stopped queue in the middle of a fragmented frame to be able to queue more frames at once (rather than just a single frame with its fragments) 2) instead of stopping the entire AC queue, queue up the frames in a per-station/per-TID queue during aggregation session initiation, when the session has come up take all those frames and put them onto the queue from 1) 3) push the ampdu queue layer abstraction this patch introduces in mac80211 into the driver, and remove the virtual queue stuff from mac80211 again This plan will probably also affect ath9k in that mac80211 queues the frames instead of passing them down, even when there are no ampdu queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-12 02:51:53 +03:00
/* also used to protect ampdu_ac_queue and amdpu_ac_stop_refcnt */
spinlock_t queue_stop_reason_lock;
mac80211: fix aggregation for hardware with ampdu queues Hardware with AMPDU queues currently has broken aggregation. This patch fixes it by making all A-MPDUs go over the regular AC queues, but keeping track of the hardware queues in mac80211. As a first rough version, it actually stops the AC queue for extended periods of time, which can be removed by adding buffering internal to mac80211, but is currently not a huge problem because people rarely use multiple TIDs that are in the same AC (and iwlwifi currently doesn't operate as AP). This is a short-term fix, my current medium-term plan, which I hope to execute soon as well, but am not sure can finish before .30, looks like this: 1) rework the internal queuing layer in mac80211 that we use for fragments if the driver stopped queue in the middle of a fragmented frame to be able to queue more frames at once (rather than just a single frame with its fragments) 2) instead of stopping the entire AC queue, queue up the frames in a per-station/per-TID queue during aggregation session initiation, when the session has come up take all those frames and put them onto the queue from 1) 3) push the ampdu queue layer abstraction this patch introduces in mac80211 into the driver, and remove the virtual queue stuff from mac80211 again This plan will probably also affect ath9k in that mac80211 queues the frames instead of passing them down, even when there are no ampdu queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-12 02:51:53 +03:00
int open_count;
int monitors, cooked_mntrs;
/* number of interfaces with corresponding FIF_ flags */
int fif_fcsfail, fif_plcpfail, fif_control, fif_other_bss, fif_pspoll;
[PATCH] mac80211: revamp interface and filter configuration Drivers are currently supposed to keep track of monitor interfaces if they allow so-called "hard" monitor, and they are also supposed to keep track of multicast etc. This patch changes that, replaces the set_multicast_list() callback with a new configure_filter() callback that takes filter flags (FIF_*) instead of interface flags (IFF_*). For a driver, this means it should open the filter as much as necessary to get all frames requested by the filter flags. Accordingly, the filter flags are named "positively", e.g. FIF_ALLMULTI. Multicast filtering is a bit special in that drivers that have no multicast address filters need to allow multicast frames through when either the FIF_ALLMULTI flag is set or when the mc_count value is positive. At the same time, drivers are no longer notified about monitor interfaces at all, this means they now need to implement the start() and stop() callbacks and the new change_filter_flags() callback. Also, the start()/stop() ordering changed, start() is now called *before* any add_interface() as it really should be, and stop() after any remove_interface(). The patch also changes the behaviour of setting the bssid to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed and the filter flag FIF_BCN_PRBRESP_PROMISC introduced. This is a lot more efficient for hardware like b43 that supports it and other hardware can still set the BSSID to all-ones. Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu (rtl8187, adm8211, and p54), Larry Finger (b43legacy), and Ivo van Doorn (rt2x00). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-09-17 09:29:23 +04:00
unsigned int filter_flags; /* FIF_* */
/* protects the aggregated multicast list and filter calls */
spinlock_t filter_lock;
/* used for uploading changed mc list */
struct work_struct reconfig_filter;
/* used to reconfigure hardware SM PS */
struct work_struct recalc_smps;
/* aggregated multicast list */
struct netdev_hw_addr_list mc_list;
bool tim_in_locked_section; /* see ieee80211_beacon_get() */
/*
* suspended is true if we finished all the suspend _and_ we have
* not yet come up from resume. This is to be used by mac80211
* to ensure driver sanity during suspend and mac80211's own
* sanity. It can eventually be used for WoW as well.
*/
bool suspended;
/*
* Resuming is true while suspended, but when we're reprogramming the
* hardware -- at that time it's allowed to use ieee80211_queue_work()
* again even though some other parts of the stack are still suspended
* and we still drop received frames to avoid waking the stack.
*/
bool resuming;
/*
* quiescing is true during the suspend process _only_ to
* ease timer cancelling etc.
*/
bool quiescing;
/* device is started */
bool started;
int tx_headroom; /* required headroom for hardware/radiotap */
/* Tasklet and skb queue to process calls from IRQ mode. All frames
* added to skb_queue will be processed, but frames in
* skb_queue_unreliable may be dropped if the total length of these
* queues increases over the limit. */
#define IEEE80211_IRQSAFE_QUEUE_LIMIT 128
struct tasklet_struct tasklet;
struct sk_buff_head skb_queue;
struct sk_buff_head skb_queue_unreliable;
/* Station data */
/*
* The mutex only protects the list and counter,
* reads are done in RCU.
* Additionally, the lock protects the hash table,
* the pending list and each BSS's TIM bitmap.
*/
struct mutex sta_mtx;
spinlock_t sta_lock;
unsigned long num_sta;
struct list_head sta_list, sta_pending_list;
struct sta_info *sta_hash[STA_HASH_SIZE];
struct timer_list sta_cleanup;
struct work_struct sta_finish_work;
int sta_generation;
struct sk_buff_head pending[IEEE80211_MAX_QUEUES];
struct tasklet_struct tx_pending_tasklet;
atomic_t agg_queue_stop[IEEE80211_MAX_QUEUES];
/* number of interfaces with corresponding IFF_ flags */
atomic_t iff_allmultis, iff_promiscs;
struct rate_control_ref *rate_ctrl;
struct crypto_blkcipher *wep_tx_tfm;
struct crypto_blkcipher *wep_rx_tfm;
u32 wep_iv;
/* see iface.c */
struct list_head interfaces;
struct mutex iflist_mtx;
/*
* Key mutex, protects sdata's key_list and sta_info's
* key pointers (write access, they're RCU.)
*/
struct mutex key_mtx;
/* Scanning and BSS list */
struct mutex scan_mtx;
unsigned long scanning;
struct cfg80211_ssid scan_ssid;
struct cfg80211_scan_request *int_scan_req;
struct cfg80211_scan_request *scan_req, *hw_scan_req;
struct ieee80211_channel *scan_channel;
enum ieee80211_band hw_scan_band;
int scan_channel_idx;
int scan_ies_len;
unsigned long leave_oper_channel_time;
enum mac80211_scan_state next_scan_state;
struct delayed_work scan_work;
struct ieee80211_sub_if_data *scan_sdata;
enum nl80211_channel_type _oper_channel_type;
struct ieee80211_channel *oper_channel, *csa_channel;
/* Temporary remain-on-channel for off-channel operations */
struct ieee80211_channel *tmp_channel;
enum nl80211_channel_type tmp_channel_type;
/* SNMP counters */
/* dot11CountersTable */
u32 dot11TransmittedFragmentCount;
u32 dot11MulticastTransmittedFrameCount;
u32 dot11FailedCount;
u32 dot11RetryCount;
u32 dot11MultipleRetryCount;
u32 dot11FrameDuplicateCount;
u32 dot11ReceivedFragmentCount;
u32 dot11MulticastReceivedFrameCount;
u32 dot11TransmittedFrameCount;
#ifdef CONFIG_MAC80211_LEDS
int tx_led_counter, rx_led_counter;
struct led_trigger *tx_led, *rx_led, *assoc_led, *radio_led;
char tx_led_name[32], rx_led_name[32],
assoc_led_name[32], radio_led_name[32];
#endif
#ifdef CONFIG_MAC80211_DEBUG_COUNTERS
/* TX/RX handler statistics */
unsigned int tx_handlers_drop;
unsigned int tx_handlers_queued;
unsigned int tx_handlers_drop_unencrypted;
unsigned int tx_handlers_drop_fragment;
unsigned int tx_handlers_drop_wep;
unsigned int tx_handlers_drop_not_assoc;
unsigned int tx_handlers_drop_unauth_port;
unsigned int rx_handlers_drop;
unsigned int rx_handlers_queued;
unsigned int rx_handlers_drop_nullfunc;
unsigned int rx_handlers_drop_defrag;
unsigned int rx_handlers_drop_short;
unsigned int rx_handlers_drop_passive_scan;
unsigned int tx_expand_skb_head;
unsigned int tx_expand_skb_head_cloned;
unsigned int rx_expand_skb_head;
unsigned int rx_expand_skb_head2;
unsigned int rx_handlers_fragments;
unsigned int tx_status_drop;
#define I802_DEBUG_INC(c) (c)++
#else /* CONFIG_MAC80211_DEBUG_COUNTERS */
#define I802_DEBUG_INC(c) do { } while (0)
#endif /* CONFIG_MAC80211_DEBUG_COUNTERS */
int total_ps_buffered; /* total number of all buffered unicast and
* multicast packets for power saving stations
*/
int wifi_wme_noack_test;
unsigned int wmm_acm; /* bit field of ACM bits (BIT(802.1D tag)) */
/*
* Bitmask of enabled u-apsd queues,
* IEEE80211_WMM_IE_STA_QOSINFO_AC_BE & co. Needs a new association
* to take effect.
*/
unsigned int uapsd_queues;
/*
* Maximum number of buffered frames AP can deliver during a
* service period, IEEE80211_WMM_IE_STA_QOSINFO_SP_ALL or similar.
* Needs a new association to take effect.
*/
unsigned int uapsd_max_sp_len;
bool pspolling;
bool offchannel_ps_enabled;
/*
* PS can only be enabled when we have exactly one managed
* interface (and monitors) in PS, this then points there.
*/
struct ieee80211_sub_if_data *ps_sdata;
struct work_struct dynamic_ps_enable_work;
struct work_struct dynamic_ps_disable_work;
struct timer_list dynamic_ps_timer;
struct notifier_block network_latency_notifier;
struct notifier_block ifa_notifier;
/*
* The dynamic ps timeout configured from user space via WEXT -
* this will override whatever chosen by mac80211 internally.
*/
int dynamic_ps_forced_timeout;
mac80211: Add interface for driver to temporarily disable dynamic ps This mechanism introduced in this patch applies (at least) for hardware designs using a single shared antenna for both WLAN and BT. In these designs, the antenna must be toggled between WLAN and BT. In those hardware, managing WLAN co-existence with Bluetooth requires WLAN full power save whenever there is Bluetooth activity in order for WLAN to be able to periodically relinquish the antenna to be used for BT. This is because BT can only access the shared antenna when WLAN is idle or asleep. Some hardware, for instance the wl1271, are able to indicate to the host whenever there is BT traffic. In essence, the hardware will send an indication to the host whenever there is, for example, SCO traffic or A2DP traffic, and will send another indication when the traffic is over. The hardware gets information of Bluetooth traffic via hardware co-existence control lines - these lines are used to negotiate the shared antenna ownership. The hardware will give the antenna to BT whenever WLAN is sleeping. This patch adds the interface to mac80211 to facilitate temporarily disabling of dynamic power save as per request of the WLAN driver. This interface will immediately force WLAN to full powersave, hence allowing BT coexistence as described above. In these kind of shared antenna desings, when WLAN powersave is fully disabled, Bluetooth will not work simultaneously with WLAN at all. This patch does not address that problem. This interface will not change PSM state, so if PSM is disabled it will remain so. Solving this problem requires knowledge about BT state, and is best done in user-space. Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-21 09:59:39 +04:00
int dynamic_ps_user_timeout;
bool disable_dynamic_ps;
int user_power_level; /* in dBm */
int power_constr_level; /* in dBm */
enum ieee80211_smps_mode smps_mode;
struct work_struct restart_work;
#ifdef CONFIG_MAC80211_DEBUGFS
struct local_debugfsdentries {
struct dentry *rcdir;
struct dentry *stations;
struct dentry *keys;
} debugfs;
#endif
};
static inline struct ieee80211_sub_if_data *
IEEE80211_DEV_TO_SUB_IF(struct net_device *dev)
{
return netdev_priv(dev);
}
/* this struct represents 802.11n's RA/TID combination */
struct ieee80211_ra_tid {
u8 ra[ETH_ALEN];
u16 tid;
};
/* Parsed Information Elements */
struct ieee802_11_elems {
u8 *ie_start;
size_t total_len;
/* pointers to IEs */
u8 *ssid;
u8 *supp_rates;
u8 *fh_params;
u8 *ds_params;
u8 *cf_params;
struct ieee80211_tim_ie *tim;
u8 *ibss_params;
u8 *challenge;
u8 *wpa;
u8 *rsn;
u8 *erp_info;
u8 *ext_supp_rates;
u8 *wmm_info;
u8 *wmm_param;
struct ieee80211_ht_cap *ht_cap_elem;
struct ieee80211_ht_info *ht_info_elem;
struct ieee80211_meshconf_ie *mesh_config;
u8 *mesh_id;
u8 *peer_link;
u8 *preq;
u8 *prep;
u8 *perr;
struct ieee80211_rann_ie *rann;
u8 *ch_switch_elem;
u8 *country_elem;
u8 *pwr_constr_elem;
u8 *quiet_elem; /* first quite element */
u8 *timeout_int;
/* length of them, respectively */
u8 ssid_len;
u8 supp_rates_len;
u8 fh_params_len;
u8 ds_params_len;
u8 cf_params_len;
u8 tim_len;
u8 ibss_params_len;
u8 challenge_len;
u8 wpa_len;
u8 rsn_len;
u8 erp_info_len;
u8 ext_supp_rates_len;
u8 wmm_info_len;
u8 wmm_param_len;
u8 mesh_id_len;
u8 peer_link_len;
u8 preq_len;
u8 prep_len;
u8 perr_len;
u8 ch_switch_elem_len;
u8 country_elem_len;
u8 pwr_constr_elem_len;
u8 quiet_elem_len;
u8 num_of_quiet_elem; /* can be more the one */
u8 timeout_int_len;
};
static inline struct ieee80211_local *hw_to_local(
struct ieee80211_hw *hw)
{
return container_of(hw, struct ieee80211_local, hw);
}
static inline struct ieee80211_hw *local_to_hw(
struct ieee80211_local *local)
{
return &local->hw;
}
static inline int ieee80211_bssid_match(const u8 *raddr, const u8 *addr)
{
return compare_ether_addr(raddr, addr) == 0 ||
is_broadcast_ether_addr(raddr);
}
int ieee80211_hw_config(struct ieee80211_local *local, u32 changed);
void ieee80211_tx_set_protected(struct ieee80211_tx_data *tx);
void ieee80211_bss_info_change_notify(struct ieee80211_sub_if_data *sdata,
u32 changed);
void ieee80211_configure_filter(struct ieee80211_local *local);
u32 ieee80211_reset_erp_info(struct ieee80211_sub_if_data *sdata);
extern bool ieee80211_disable_40mhz_24ghz;
/* STA code */
void ieee80211_sta_setup_sdata(struct ieee80211_sub_if_data *sdata);
int ieee80211_mgd_auth(struct ieee80211_sub_if_data *sdata,
struct cfg80211_auth_request *req);
int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
struct cfg80211_assoc_request *req);
int ieee80211_mgd_deauth(struct ieee80211_sub_if_data *sdata,
struct cfg80211_deauth_request *req,
void *cookie);
int ieee80211_mgd_disassoc(struct ieee80211_sub_if_data *sdata,
struct cfg80211_disassoc_request *req,
void *cookie);
void ieee80211_send_pspoll(struct ieee80211_local *local,
struct ieee80211_sub_if_data *sdata);
void ieee80211_recalc_ps(struct ieee80211_local *local, s32 latency);
int ieee80211_max_network_latency(struct notifier_block *nb,
unsigned long data, void *dummy);
int ieee80211_set_arp_filter(struct ieee80211_sub_if_data *sdata);
void ieee80211_sta_process_chanswitch(struct ieee80211_sub_if_data *sdata,
struct ieee80211_channel_sw_ie *sw_elem,
struct ieee80211_bss *bss,
u64 timestamp);
void ieee80211_sta_quiesce(struct ieee80211_sub_if_data *sdata);
void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata);
void ieee80211_sta_work(struct ieee80211_sub_if_data *sdata);
void ieee80211_sta_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb);
/* IBSS code */
void ieee80211_ibss_notify_scan_completed(struct ieee80211_local *local);
void ieee80211_ibss_setup_sdata(struct ieee80211_sub_if_data *sdata);
struct sta_info *ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
u8 *bssid, u8 *addr, u32 supp_rates,
gfp_t gfp);
int ieee80211_ibss_join(struct ieee80211_sub_if_data *sdata,
struct cfg80211_ibss_params *params);
int ieee80211_ibss_leave(struct ieee80211_sub_if_data *sdata);
void ieee80211_ibss_quiesce(struct ieee80211_sub_if_data *sdata);
void ieee80211_ibss_restart(struct ieee80211_sub_if_data *sdata);
void ieee80211_ibss_work(struct ieee80211_sub_if_data *sdata);
void ieee80211_ibss_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb);
/* mesh code */
void ieee80211_mesh_work(struct ieee80211_sub_if_data *sdata);
void ieee80211_mesh_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb);
/* scan/BSS handling */
void ieee80211_scan_work(struct work_struct *work);
int ieee80211_request_internal_scan(struct ieee80211_sub_if_data *sdata,
const u8 *ssid, u8 ssid_len,
struct ieee80211_channel *chan);
int ieee80211_request_scan(struct ieee80211_sub_if_data *sdata,
struct cfg80211_scan_request *req);
void ieee80211_scan_cancel(struct ieee80211_local *local);
ieee80211_rx_result
ieee80211_scan_rx(struct ieee80211_sub_if_data *sdata, struct sk_buff *skb);
void ieee80211_mlme_notify_scan_completed(struct ieee80211_local *local);
struct ieee80211_bss *
ieee80211_bss_info_update(struct ieee80211_local *local,
struct ieee80211_rx_status *rx_status,
struct ieee80211_mgmt *mgmt,
size_t len,
struct ieee802_11_elems *elems,
struct ieee80211_channel *channel,
bool beacon);
struct ieee80211_bss *
ieee80211_rx_bss_get(struct ieee80211_local *local, u8 *bssid, int freq,
u8 *ssid, u8 ssid_len);
void ieee80211_rx_bss_put(struct ieee80211_local *local,
struct ieee80211_bss *bss);
/* off-channel helpers */
void ieee80211_offchannel_stop_beaconing(struct ieee80211_local *local);
void ieee80211_offchannel_stop_station(struct ieee80211_local *local);
void ieee80211_offchannel_return(struct ieee80211_local *local,
bool enable_beaconing);
/* interface handling */
int ieee80211_iface_init(void);
void ieee80211_iface_exit(void);
int ieee80211_if_add(struct ieee80211_local *local, const char *name,
struct net_device **new_dev, enum nl80211_iftype type,
struct vif_params *params);
int ieee80211_if_change_type(struct ieee80211_sub_if_data *sdata,
enum nl80211_iftype type);
void ieee80211_if_remove(struct ieee80211_sub_if_data *sdata);
void ieee80211_remove_interfaces(struct ieee80211_local *local);
mac80211: tell driver when idle When we aren't doing anything in mac80211, we can turn off much of the hardware, depending on the driver/hw. Not doing anything, aka being idle, means: * no monitor interfaces * no AP/mesh/wds interfaces * any station interfaces are in DISABLED state * any IBSS interfaces aren't trying to be in a network * we aren't trying to scan By creating a new function that verifies these conditions and calling it at strategic points where the states of those conditions change, we can easily make mac80211 tell the driver when we are idle to save power. Additionally, this fixes a small quirk where a recalculated powersave state is passed to the driver even if the hardware is about to stopped completely. This patch intentionally doesn't touch radio_enabled because that is currently implemented to be a soft rfkill which is inappropriate here when we need to be able to wake up with low latency. One thing I'm not entirely sure about is this: phy0: device no longer idle - in use wlan0: direct probe to AP 00:11:24:91:07:4d try 1 wlan0 direct probe responded wlan0: authenticate with AP 00:11:24:91:07:4d wlan0: authenticated > phy0: device now idle > phy0: device no longer idle - in use wlan0: associate with AP 00:11:24:91:07:4d wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1) wlan0: associated Is it appropriate to go into idle state for a short time when we have just authenticated, but not associated yet? This happens only with the userspace SME, because we cannot really know how long it will wait before asking us to associate. Would going idle after a short timeout be more appropriate? We may need to revisit this, depending on what happens. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-29 14:26:17 +04:00
u32 __ieee80211_recalc_idle(struct ieee80211_local *local);
void ieee80211_recalc_idle(struct ieee80211_local *local);
static inline bool ieee80211_sdata_running(struct ieee80211_sub_if_data *sdata)
{
return netif_running(sdata->dev);
}
/* tx handling */
void ieee80211_clear_tx_pending(struct ieee80211_local *local);
void ieee80211_tx_pending(unsigned long data);
netdev_tx_t ieee80211_monitor_start_xmit(struct sk_buff *skb,
struct net_device *dev);
netdev_tx_t ieee80211_subif_start_xmit(struct sk_buff *skb,
struct net_device *dev);
/*
* radiotap header for status frames
*/
struct ieee80211_tx_status_rtap_hdr {
struct ieee80211_radiotap_header hdr;
u8 rate;
u8 padding_for_rate;
__le16 tx_flags;
u8 data_retries;
} __packed;
/* HT */
void ieee80211_ht_cap_ie_to_sta_ht_cap(struct ieee80211_supported_band *sband,
struct ieee80211_ht_cap *ht_cap_ie,
struct ieee80211_sta_ht_cap *ht_cap);
void ieee80211_send_bar(struct ieee80211_sub_if_data *sdata, u8 *ra, u16 tid, u16 ssn);
void ieee80211_send_delba(struct ieee80211_sub_if_data *sdata,
const u8 *da, u16 tid,
u16 initiator, u16 reason_code);
int ieee80211_send_smps_action(struct ieee80211_sub_if_data *sdata,
enum ieee80211_smps_mode smps, const u8 *da,
const u8 *bssid);
void ___ieee80211_stop_rx_ba_session(struct sta_info *sta, u16 tid,
u16 initiator, u16 reason);
void __ieee80211_stop_rx_ba_session(struct sta_info *sta, u16 tid,
u16 initiator, u16 reason);
void ieee80211_sta_tear_down_BA_sessions(struct sta_info *sta);
void ieee80211_process_delba(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta,
struct ieee80211_mgmt *mgmt, size_t len);
void ieee80211_process_addba_resp(struct ieee80211_local *local,
struct sta_info *sta,
struct ieee80211_mgmt *mgmt,
size_t len);
void ieee80211_process_addba_request(struct ieee80211_local *local,
struct sta_info *sta,
struct ieee80211_mgmt *mgmt,
size_t len);
int __ieee80211_stop_tx_ba_session(struct sta_info *sta, u16 tid,
enum ieee80211_back_parties initiator);
int ___ieee80211_stop_tx_ba_session(struct sta_info *sta, u16 tid,
enum ieee80211_back_parties initiator);
void ieee80211_start_tx_ba_cb(struct ieee80211_vif *vif, u8 *ra, u16 tid);
void ieee80211_stop_tx_ba_cb(struct ieee80211_vif *vif, u8 *ra, u8 tid);
void ieee80211_ba_session_work(struct work_struct *work);
void ieee80211_tx_ba_session_handle_start(struct sta_info *sta, int tid);
/* Spectrum management */
void ieee80211_process_measurement_req(struct ieee80211_sub_if_data *sdata,
struct ieee80211_mgmt *mgmt,
size_t len);
/* Suspend/resume and hw reconfiguration */
int ieee80211_reconfig(struct ieee80211_local *local);
void ieee80211_stop_device(struct ieee80211_local *local);
#ifdef CONFIG_PM
int __ieee80211_suspend(struct ieee80211_hw *hw);
static inline int __ieee80211_resume(struct ieee80211_hw *hw)
{
return ieee80211_reconfig(hw_to_local(hw));
}
#else
static inline int __ieee80211_suspend(struct ieee80211_hw *hw)
{
return 0;
}
static inline int __ieee80211_resume(struct ieee80211_hw *hw)
{
return 0;
}
#endif
/* utility functions/constants */
extern void *mac80211_wiphy_privid; /* for wiphy privid */
u8 *ieee80211_get_bssid(struct ieee80211_hdr *hdr, size_t len,
enum nl80211_iftype type);
int ieee80211_frame_duration(struct ieee80211_local *local, size_t len,
int rate, int erp, int short_preamble);
void mac80211_ev_michael_mic_failure(struct ieee80211_sub_if_data *sdata, int keyidx,
struct ieee80211_hdr *hdr, const u8 *tsc,
gfp_t gfp);
void ieee80211_set_wmm_default(struct ieee80211_sub_if_data *sdata);
void ieee80211_tx_skb(struct ieee80211_sub_if_data *sdata, struct sk_buff *skb);
void ieee802_11_parse_elems(u8 *start, size_t len,
struct ieee802_11_elems *elems);
u32 ieee802_11_parse_elems_crc(u8 *start, size_t len,
struct ieee802_11_elems *elems,
u64 filter, u32 crc);
u32 ieee80211_mandatory_rates(struct ieee80211_local *local,
enum ieee80211_band band);
void ieee80211_dynamic_ps_enable_work(struct work_struct *work);
void ieee80211_dynamic_ps_disable_work(struct work_struct *work);
void ieee80211_dynamic_ps_timer(unsigned long data);
void ieee80211_send_nullfunc(struct ieee80211_local *local,
struct ieee80211_sub_if_data *sdata,
int powersave);
void ieee80211_sta_rx_notify(struct ieee80211_sub_if_data *sdata,
struct ieee80211_hdr *hdr);
void ieee80211_beacon_connection_loss_work(struct work_struct *work);
void ieee80211_wake_queues_by_reason(struct ieee80211_hw *hw,
enum queue_stop_reason reason);
void ieee80211_stop_queues_by_reason(struct ieee80211_hw *hw,
enum queue_stop_reason reason);
mac80211: fix aggregation for hardware with ampdu queues Hardware with AMPDU queues currently has broken aggregation. This patch fixes it by making all A-MPDUs go over the regular AC queues, but keeping track of the hardware queues in mac80211. As a first rough version, it actually stops the AC queue for extended periods of time, which can be removed by adding buffering internal to mac80211, but is currently not a huge problem because people rarely use multiple TIDs that are in the same AC (and iwlwifi currently doesn't operate as AP). This is a short-term fix, my current medium-term plan, which I hope to execute soon as well, but am not sure can finish before .30, looks like this: 1) rework the internal queuing layer in mac80211 that we use for fragments if the driver stopped queue in the middle of a fragmented frame to be able to queue more frames at once (rather than just a single frame with its fragments) 2) instead of stopping the entire AC queue, queue up the frames in a per-station/per-TID queue during aggregation session initiation, when the session has come up take all those frames and put them onto the queue from 1) 3) push the ampdu queue layer abstraction this patch introduces in mac80211 into the driver, and remove the virtual queue stuff from mac80211 again This plan will probably also affect ath9k in that mac80211 queues the frames instead of passing them down, even when there are no ampdu queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-12 02:51:53 +03:00
void ieee80211_wake_queue_by_reason(struct ieee80211_hw *hw, int queue,
enum queue_stop_reason reason);
void ieee80211_stop_queue_by_reason(struct ieee80211_hw *hw, int queue,
enum queue_stop_reason reason);
void ieee80211_add_pending_skb(struct ieee80211_local *local,
struct sk_buff *skb);
int ieee80211_add_pending_skbs(struct ieee80211_local *local,
struct sk_buff_head *skbs);
void ieee80211_send_auth(struct ieee80211_sub_if_data *sdata,
u16 transaction, u16 auth_alg,
u8 *extra, size_t extra_len, const u8 *bssid,
const u8 *key, u8 key_len, u8 key_idx);
int ieee80211_build_preq_ies(struct ieee80211_local *local, u8 *buffer,
const u8 *ie, size_t ie_len,
enum ieee80211_band band);
void ieee80211_send_probe_req(struct ieee80211_sub_if_data *sdata, u8 *dst,
const u8 *ssid, size_t ssid_len,
const u8 *ie, size_t ie_len);
void ieee80211_sta_def_wmm_params(struct ieee80211_sub_if_data *sdata,
const size_t supp_rates_len,
const u8 *supp_rates);
u32 ieee80211_sta_get_rates(struct ieee80211_local *local,
struct ieee802_11_elems *elems,
enum ieee80211_band band);
int __ieee80211_request_smps(struct ieee80211_sub_if_data *sdata,
enum ieee80211_smps_mode smps_mode);
void ieee80211_recalc_smps(struct ieee80211_local *local,
struct ieee80211_sub_if_data *forsdata);
size_t ieee80211_ie_split(const u8 *ies, size_t ielen,
const u8 *ids, int n_ids, size_t offset);
size_t ieee80211_ie_split_vendor(const u8 *ies, size_t ielen, size_t offset);
/* internal work items */
void ieee80211_work_init(struct ieee80211_local *local);
void ieee80211_add_work(struct ieee80211_work *wk);
void free_work(struct ieee80211_work *wk);
void ieee80211_work_purge(struct ieee80211_sub_if_data *sdata);
ieee80211_rx_result ieee80211_work_rx_mgmt(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb);
int ieee80211_wk_remain_on_channel(struct ieee80211_sub_if_data *sdata,
struct ieee80211_channel *chan,
enum nl80211_channel_type channel_type,
unsigned int duration, u64 *cookie);
int ieee80211_wk_cancel_remain_on_channel(
struct ieee80211_sub_if_data *sdata, u64 cookie);
cfg80211/mac80211: better channel handling Currently (all tested with hwsim) you can do stupid things like setting up an AP on a certain channel, then adding another virtual interface and making that associate on another channel -- this will make the beaconing to move channel but obviously without the necessary IEs data update. In order to improve this situation, first make the configuration APIs (cfg80211 and nl80211) aware of multi-channel operation -- we'll eventually need that in the future anyway. There's one userland API change and one API addition. The API change is that now SET_WIPHY must be called with virtual interface index rather than only wiphy index in order to take effect for that interface -- luckily all current users (hostapd) do that. For monitor interfaces, the old setting is preserved, but monitors are always slaved to other devices anyway so no guarantees. The second userland API change is the introduction of a per virtual interface SET_CHANNEL command, that hostapd should use going forward to make it easier to understand what's going on (it can automatically detect a kernel with this command). Other than mac80211, no existing cfg80211 drivers are affected by this change because they only allow a single virtual interface. mac80211, however, now needs to be aware that the channel settings are per interface now, and needs to disallow (for now) real multi-channel operation, which is another important part of this patch. One of the immediate benefits is that you can now start hostapd to operate on a hardware that already has a connection on another virtual interface, as long as you specify the same channel. Note that two things are left unhandled (this is an improvement -- not a complete fix): * different HT/no-HT modes currently you could start an HT AP and then connect to a non-HT network on the same channel which would configure the hardware for no HT; that can be fixed fairly easily * CSA An AP we're connected to on a virtual interface might indicate switching channels, and in that case we would follow it, regardless of how many other interfaces are operating; this requires more effort to fix but is pretty rare after all Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-05 17:25:02 +04:00
/* channel management */
enum ieee80211_chan_mode {
CHAN_MODE_UNDEFINED,
CHAN_MODE_HOPPING,
CHAN_MODE_FIXED,
};
enum ieee80211_chan_mode
ieee80211_get_channel_mode(struct ieee80211_local *local,
struct ieee80211_sub_if_data *ignore);
bool ieee80211_set_channel_type(struct ieee80211_local *local,
struct ieee80211_sub_if_data *sdata,
enum nl80211_channel_type chantype);
cfg80211/mac80211: better channel handling Currently (all tested with hwsim) you can do stupid things like setting up an AP on a certain channel, then adding another virtual interface and making that associate on another channel -- this will make the beaconing to move channel but obviously without the necessary IEs data update. In order to improve this situation, first make the configuration APIs (cfg80211 and nl80211) aware of multi-channel operation -- we'll eventually need that in the future anyway. There's one userland API change and one API addition. The API change is that now SET_WIPHY must be called with virtual interface index rather than only wiphy index in order to take effect for that interface -- luckily all current users (hostapd) do that. For monitor interfaces, the old setting is preserved, but monitors are always slaved to other devices anyway so no guarantees. The second userland API change is the introduction of a per virtual interface SET_CHANNEL command, that hostapd should use going forward to make it easier to understand what's going on (it can automatically detect a kernel with this command). Other than mac80211, no existing cfg80211 drivers are affected by this change because they only allow a single virtual interface. mac80211, however, now needs to be aware that the channel settings are per interface now, and needs to disallow (for now) real multi-channel operation, which is another important part of this patch. One of the immediate benefits is that you can now start hostapd to operate on a hardware that already has a connection on another virtual interface, as long as you specify the same channel. Note that two things are left unhandled (this is an improvement -- not a complete fix): * different HT/no-HT modes currently you could start an HT AP and then connect to a non-HT network on the same channel which would configure the hardware for no HT; that can be fixed fairly easily * CSA An AP we're connected to on a virtual interface might indicate switching channels, and in that case we would follow it, regardless of how many other interfaces are operating; this requires more effort to fix but is pretty rare after all Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-05 17:25:02 +04:00
#ifdef CONFIG_MAC80211_NOINLINE
#define debug_noinline noinline
#else
#define debug_noinline
#endif
#endif /* IEEE80211_I_H */