microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/net/sched/act_skbmod.c

314 строки
7.8 KiB
C
Исходник Обычный вид История

net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
/*
* net/sched/act_skbmod.c skb data modifier
*
* Copyright (c) 2016 Jamal Hadi Salim <jhs@mojatatu.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/skbuff.h>
#include <linux/rtnetlink.h>
#include <net/netlink.h>
#include <net/pkt_sched.h>
#include <linux/tc_act/tc_skbmod.h>
#include <net/tc_act/tc_skbmod.h>
netns: make struct pernet_operations::id unsigned int Make struct pernet_operations::id unsigned. There are 2 reasons to do so: 1) This field is really an index into an zero based array and thus is unsigned entity. Using negative value is out-of-bound access by definition. 2) On x86_64 unsigned 32-bit data which are mixed with pointers via array indexing or offsets added or subtracted to pointers are preffered to signed 32-bit data. "int" being used as an array index needs to be sign-extended to 64-bit before being used. void f(long *p, int i) { g(p[i]); } roughly translates to movsx rsi, esi mov rdi, [rsi+...] call g MOVSX is 3 byte instruction which isn't necessary if the variable is unsigned because x86_64 is zero extending by default. Now, there is net_generic() function which, you guessed it right, uses "int" as an array index: static inline void *net_generic(const struct net *net, int id) { ... ptr = ng->ptr[id - 1]; ... } And this function is used a lot, so those sign extensions add up. Patch snipes ~1730 bytes on allyesconfig kernel (without all junk messing with code generation): add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730) Unfortunately some functions actually grow bigger. This is a semmingly random artefact of code generation with register allocator being used differently. gcc decides that some variable needs to live in new r8+ registers and every access now requires REX prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be used which is longer than [r8] However, overall balance is in negative direction: add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730) function old new delta nfsd4_lock 3886 3959 +73 tipc_link_build_proto_msg 1096 1140 +44 mac80211_hwsim_new_radio 2776 2808 +32 tipc_mon_rcv 1032 1058 +26 svcauth_gss_legacy_init 1413 1429 +16 tipc_bcbase_select_primary 379 392 +13 nfsd4_exchange_id 1247 1260 +13 nfsd4_setclientid_confirm 782 793 +11 ... put_client_renew_locked 494 480 -14 ip_set_sockfn_get 730 716 -14 geneve_sock_add 829 813 -16 nfsd4_sequence_done 721 703 -18 nlmclnt_lookup_host 708 686 -22 nfsd4_lockt 1085 1063 -22 nfs_get_client 1077 1050 -27 tcf_bpf_init 1106 1076 -30 nfsd4_encode_fattr 5997 5930 -67 Total: Before=154856051, After=154854321, chg -0.00% Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-17 04:58:21 +03:00
static unsigned int skbmod_net_id;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
static struct tc_action_ops act_skbmod_ops;
#define MAX_EDIT_LEN ETH_HLEN
static int tcf_skbmod_run(struct sk_buff *skb, const struct tc_action *a,
struct tcf_result *res)
{
struct tcf_skbmod *d = to_skbmod(a);
int action;
struct tcf_skbmod_params *p;
u64 flags;
int err;
tcf_lastuse_update(&d->tcf_tm);
bstats_cpu_update(this_cpu_ptr(d->common.cpu_bstats), skb);
/* XXX: if you are going to edit more fields beyond ethernet header
* (example when you add IP header replacement or vlan swap)
* then MAX_EDIT_LEN needs to change appropriately
*/
err = skb_ensure_writable(skb, MAX_EDIT_LEN);
tc/act: remove unneeded RCU lock in action callback Each lockless action currently does its own RCU locking in ->act(). This allows using plain RCU accessor, even if the context is really RCU BH. This change drops the per action RCU lock, replace the accessors with the _bh variant, cleans up a bit the surrounding code and documents the RCU status in the relevant header. No functional nor performance change is intended. The goal of this patch is clarifying that the RCU critical section used by the tc actions extends up to the classifier's caller. v1 -> v2: - preserve rcu lock in act_bpf: it's needed by eBPF helpers, as pointed out by Daniel v3 -> v4: - fixed some typos in the commit message (JiriP) Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-30 15:30:43 +03:00
if (unlikely(err)) /* best policy is to drop on the floor */
goto drop;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
action = READ_ONCE(d->tcf_action);
tc/act: remove unneeded RCU lock in action callback Each lockless action currently does its own RCU locking in ->act(). This allows using plain RCU accessor, even if the context is really RCU BH. This change drops the per action RCU lock, replace the accessors with the _bh variant, cleans up a bit the surrounding code and documents the RCU status in the relevant header. No functional nor performance change is intended. The goal of this patch is clarifying that the RCU critical section used by the tc actions extends up to the classifier's caller. v1 -> v2: - preserve rcu lock in act_bpf: it's needed by eBPF helpers, as pointed out by Daniel v3 -> v4: - fixed some typos in the commit message (JiriP) Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-30 15:30:43 +03:00
if (unlikely(action == TC_ACT_SHOT))
goto drop;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
tc/act: remove unneeded RCU lock in action callback Each lockless action currently does its own RCU locking in ->act(). This allows using plain RCU accessor, even if the context is really RCU BH. This change drops the per action RCU lock, replace the accessors with the _bh variant, cleans up a bit the surrounding code and documents the RCU status in the relevant header. No functional nor performance change is intended. The goal of this patch is clarifying that the RCU critical section used by the tc actions extends up to the classifier's caller. v1 -> v2: - preserve rcu lock in act_bpf: it's needed by eBPF helpers, as pointed out by Daniel v3 -> v4: - fixed some typos in the commit message (JiriP) Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-30 15:30:43 +03:00
p = rcu_dereference_bh(d->skbmod_p);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
flags = p->flags;
if (flags & SKBMOD_F_DMAC)
ether_addr_copy(eth_hdr(skb)->h_dest, p->eth_dst);
if (flags & SKBMOD_F_SMAC)
ether_addr_copy(eth_hdr(skb)->h_source, p->eth_src);
if (flags & SKBMOD_F_ETYPE)
eth_hdr(skb)->h_proto = p->eth_type;
if (flags & SKBMOD_F_SWAPMAC) {
u16 tmpaddr[ETH_ALEN / 2]; /* ether_addr_copy() requirement */
/*XXX: I am sure we can come up with more efficient swapping*/
ether_addr_copy((u8 *)tmpaddr, eth_hdr(skb)->h_dest);
ether_addr_copy(eth_hdr(skb)->h_dest, eth_hdr(skb)->h_source);
ether_addr_copy(eth_hdr(skb)->h_source, (u8 *)tmpaddr);
}
return action;
tc/act: remove unneeded RCU lock in action callback Each lockless action currently does its own RCU locking in ->act(). This allows using plain RCU accessor, even if the context is really RCU BH. This change drops the per action RCU lock, replace the accessors with the _bh variant, cleans up a bit the surrounding code and documents the RCU status in the relevant header. No functional nor performance change is intended. The goal of this patch is clarifying that the RCU critical section used by the tc actions extends up to the classifier's caller. v1 -> v2: - preserve rcu lock in act_bpf: it's needed by eBPF helpers, as pointed out by Daniel v3 -> v4: - fixed some typos in the commit message (JiriP) Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-30 15:30:43 +03:00
drop:
qstats_overlimit_inc(this_cpu_ptr(d->common.cpu_qstats));
return TC_ACT_SHOT;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
static const struct nla_policy skbmod_policy[TCA_SKBMOD_MAX + 1] = {
[TCA_SKBMOD_PARMS] = { .len = sizeof(struct tc_skbmod) },
[TCA_SKBMOD_DMAC] = { .len = ETH_ALEN },
[TCA_SKBMOD_SMAC] = { .len = ETH_ALEN },
[TCA_SKBMOD_ETYPE] = { .type = NLA_U16 },
};
static int tcf_skbmod_init(struct net *net, struct nlattr *nla,
struct nlattr *est, struct tc_action **a,
net: sched: implement unlocked action init API Add additional 'rtnl_held' argument to act API init functions. It is required to implement actions that need to release rtnl lock before loading kernel module and reacquire if afterwards. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:25 +03:00
int ovr, int bind, bool rtnl_held,
struct netlink_ext_ack *extack)
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
{
struct tc_action_net *tn = net_generic(net, skbmod_net_id);
struct nlattr *tb[TCA_SKBMOD_MAX + 1];
struct tcf_skbmod_params *p, *p_old;
struct tc_skbmod *parm;
struct tcf_skbmod *d;
bool exists = false;
u8 *daddr = NULL;
u8 *saddr = NULL;
u16 eth_type = 0;
u32 lflags = 0;
int ret = 0, err;
if (!nla)
return -EINVAL;
netlink: pass extended ACK struct to parsing functions Pass the new extended ACK reporting struct to all of the generic netlink parsing functions. For now, pass NULL in almost all callers (except for some in the core.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-12 15:34:07 +03:00
err = nla_parse_nested(tb, TCA_SKBMOD_MAX, nla, skbmod_policy, NULL);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
if (err < 0)
return err;
if (!tb[TCA_SKBMOD_PARMS])
return -EINVAL;
if (tb[TCA_SKBMOD_DMAC]) {
daddr = nla_data(tb[TCA_SKBMOD_DMAC]);
lflags |= SKBMOD_F_DMAC;
}
if (tb[TCA_SKBMOD_SMAC]) {
saddr = nla_data(tb[TCA_SKBMOD_SMAC]);
lflags |= SKBMOD_F_SMAC;
}
if (tb[TCA_SKBMOD_ETYPE]) {
eth_type = nla_get_u16(tb[TCA_SKBMOD_ETYPE]);
lflags |= SKBMOD_F_ETYPE;
}
parm = nla_data(tb[TCA_SKBMOD_PARMS]);
if (parm->flags & SKBMOD_F_SWAPMAC)
lflags = SKBMOD_F_SWAPMAC;
net: sched: atomically check-allocate action Implement function that atomically checks if action exists and either takes reference to it, or allocates idr slot for action index to prevent concurrent allocations of actions with same index. Use EBUSY error pointer to indicate that idr slot is reserved. Implement cleanup helper function that removes temporary error pointer from idr. (in case of error between idr allocation and insertion of newly created action to specified index) Refactor all action init functions to insert new action to idr using this API. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:32 +03:00
err = tcf_idr_check_alloc(tn, &parm->index, a, bind);
if (err < 0)
return err;
exists = err;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
if (exists && bind)
return 0;
net sched actions: fix refcnt leak in skbmod When application fails to pass flags in netlink TLV when replacing existing skbmod action, the kernel will leak refcnt: $ tc actions get action skbmod index 1 total acts 0 action order 0: skbmod pipe set smac 00:11:22:33:44:55 index 1 ref 1 bind 0 For example, at this point a buggy application replaces the action with index 1 with new smac 00:aa:22:33:44:55, it fails because of zero flags, however refcnt gets bumped: $ tc actions get actions skbmod index 1 total acts 0 action order 0: skbmod pipe set smac 00:11:22:33:44:55 index 1 ref 2 bind 0 $ Tha patch fixes this by calling tcf_idr_release() on existing actions. Fixes: 86da71b57383d ("net_sched: Introduce skbmod action") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-11 21:35:33 +03:00
if (!lflags) {
if (exists)
tcf_idr_release(*a, bind);
net: sched: atomically check-allocate action Implement function that atomically checks if action exists and either takes reference to it, or allocates idr slot for action index to prevent concurrent allocations of actions with same index. Use EBUSY error pointer to indicate that idr slot is reserved. Implement cleanup helper function that removes temporary error pointer from idr. (in case of error between idr allocation and insertion of newly created action to specified index) Refactor all action init functions to insert new action to idr using this API. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:32 +03:00
else
tcf_idr_cleanup(tn, parm->index);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
return -EINVAL;
net sched actions: fix refcnt leak in skbmod When application fails to pass flags in netlink TLV when replacing existing skbmod action, the kernel will leak refcnt: $ tc actions get action skbmod index 1 total acts 0 action order 0: skbmod pipe set smac 00:11:22:33:44:55 index 1 ref 1 bind 0 For example, at this point a buggy application replaces the action with index 1 with new smac 00:aa:22:33:44:55, it fails because of zero flags, however refcnt gets bumped: $ tc actions get actions skbmod index 1 total acts 0 action order 0: skbmod pipe set smac 00:11:22:33:44:55 index 1 ref 2 bind 0 $ Tha patch fixes this by calling tcf_idr_release() on existing actions. Fixes: 86da71b57383d ("net_sched: Introduce skbmod action") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-11 21:35:33 +03:00
}
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
if (!exists) {
net/sched: Change act_api and act_xxx modules to use IDR Typically, each TC filter has its own action. All the actions of the same type are saved in its hash table. But the hash buckets are too small that it degrades to a list. And the performance is greatly affected. For example, it takes about 0m11.914s to insert 64K rules. If we convert the hash table to IDR, it only takes about 0m1.500s. The improvement is huge. But please note that the test result is based on previous patch that cls_flower uses IDR. Signed-off-by: Chris Mi <chrism@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-30 09:31:59 +03:00
ret = tcf_idr_create(tn, parm->index, est, a,
&act_skbmod_ops, bind, true);
net: sched: atomically check-allocate action Implement function that atomically checks if action exists and either takes reference to it, or allocates idr slot for action index to prevent concurrent allocations of actions with same index. Use EBUSY error pointer to indicate that idr slot is reserved. Implement cleanup helper function that removes temporary error pointer from idr. (in case of error between idr allocation and insertion of newly created action to specified index) Refactor all action init functions to insert new action to idr using this API. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:32 +03:00
if (ret) {
tcf_idr_cleanup(tn, parm->index);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
return ret;
net: sched: atomically check-allocate action Implement function that atomically checks if action exists and either takes reference to it, or allocates idr slot for action index to prevent concurrent allocations of actions with same index. Use EBUSY error pointer to indicate that idr slot is reserved. Implement cleanup helper function that removes temporary error pointer from idr. (in case of error between idr allocation and insertion of newly created action to specified index) Refactor all action init functions to insert new action to idr using this API. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:32 +03:00
}
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
ret = ACT_P_CREATED;
net: sched: don't release reference on action overwrite Return from action init function with reference to action taken, even when overwriting existing action. Action init API initializes its fourth argument (pointer to pointer to tc action) to either existing action with same index or newly created action. In case of existing index(and bind argument is zero), init function returns without incrementing action reference counter. Caller of action init then proceeds working with action, without actually holding reference to it. This means that action could be deleted concurrently. Change action init behavior to always take reference to action before returning successfully, in order to protect from concurrent deletion. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:30 +03:00
} else if (!ovr) {
net/sched: Change act_api and act_xxx modules to use IDR Typically, each TC filter has its own action. All the actions of the same type are saved in its hash table. But the hash buckets are too small that it degrades to a list. And the performance is greatly affected. For example, it takes about 0m11.914s to insert 64K rules. If we convert the hash table to IDR, it only takes about 0m1.500s. The improvement is huge. But please note that the test result is based on previous patch that cls_flower uses IDR. Signed-off-by: Chris Mi <chrism@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-30 09:31:59 +03:00
tcf_idr_release(*a, bind);
net: sched: don't release reference on action overwrite Return from action init function with reference to action taken, even when overwriting existing action. Action init API initializes its fourth argument (pointer to pointer to tc action) to either existing action with same index or newly created action. In case of existing index(and bind argument is zero), init function returns without incrementing action reference counter. Caller of action init then proceeds working with action, without actually holding reference to it. This means that action could be deleted concurrently. Change action init behavior to always take reference to action before returning successfully, in order to protect from concurrent deletion. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:30 +03:00
return -EEXIST;
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
d = to_skbmod(*a);
ASSERT_RTNL();
p = kzalloc(sizeof(struct tcf_skbmod_params), GFP_KERNEL);
if (unlikely(!p)) {
net: sched: don't release reference on action overwrite Return from action init function with reference to action taken, even when overwriting existing action. Action init API initializes its fourth argument (pointer to pointer to tc action) to either existing action with same index or newly created action. In case of existing index(and bind argument is zero), init function returns without incrementing action reference counter. Caller of action init then proceeds working with action, without actually holding reference to it. This means that action could be deleted concurrently. Change action init behavior to always take reference to action before returning successfully, in order to protect from concurrent deletion. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:30 +03:00
tcf_idr_release(*a, bind);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
return -ENOMEM;
}
p->flags = lflags;
d->tcf_action = parm->action;
p_old = rtnl_dereference(d->skbmod_p);
if (ovr)
spin_lock_bh(&d->tcf_lock);
if (lflags & SKBMOD_F_DMAC)
ether_addr_copy(p->eth_dst, daddr);
if (lflags & SKBMOD_F_SMAC)
ether_addr_copy(p->eth_src, saddr);
if (lflags & SKBMOD_F_ETYPE)
p->eth_type = htons(eth_type);
rcu_assign_pointer(d->skbmod_p, p);
if (ovr)
spin_unlock_bh(&d->tcf_lock);
if (p_old)
kfree_rcu(p_old, rcu);
if (ret == ACT_P_CREATED)
net/sched: Change act_api and act_xxx modules to use IDR Typically, each TC filter has its own action. All the actions of the same type are saved in its hash table. But the hash buckets are too small that it degrades to a list. And the performance is greatly affected. For example, it takes about 0m11.914s to insert 64K rules. If we convert the hash table to IDR, it only takes about 0m1.500s. The improvement is huge. But please note that the test result is based on previous patch that cls_flower uses IDR. Signed-off-by: Chris Mi <chrism@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-30 09:31:59 +03:00
tcf_idr_insert(tn, *a);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
return ret;
}
net_sched: remove unused parameter from act cleanup ops No one actually uses it. Cc: Jiri Pirko <jiri@mellanox.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-05 23:53:07 +03:00
static void tcf_skbmod_cleanup(struct tc_action *a)
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
{
struct tcf_skbmod *d = to_skbmod(a);
struct tcf_skbmod_params *p;
p = rcu_dereference_protected(d->skbmod_p, 1);
net/sched: fix NULL dereference on the error path of tcf_skbmod_init() when the following command # tc action replace action skbmod swap mac index 100 is run for the first time, and tcf_skbmod_init() fails to allocate struct tcf_skbmod_params, tcf_skbmod_cleanup() calls kfree_rcu(NULL), thus causing the following error: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 IP: __call_rcu+0x23/0x2b0 PGD 8000000034057067 P4D 8000000034057067 PUD 74937067 PMD 0 Oops: 0002 [#1] SMP PTI Modules linked in: act_skbmod(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec crct10dif_pclmul mbcache jbd2 crc32_pclmul snd_hda_core ghash_clmulni_intel snd_hwdep pcbc snd_seq snd_seq_device snd_pcm aesni_intel snd_timer crypto_simd glue_helper snd cryptd virtio_balloon joydev soundcore pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_console virtio_net virtio_blk ata_piix libata crc32c_intel virtio_pci serio_raw virtio_ring virtio i2c_core floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_skbmod] CPU: 3 PID: 3144 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:__call_rcu+0x23/0x2b0 RSP: 0018:ffffbd2e403e7798 EFLAGS: 00010246 RAX: ffffffffc0872080 RBX: ffff981d34bff780 RCX: 00000000ffffffff RDX: ffffffff922a5f00 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000021f R10: 000000003d003000 R11: 0000000000aaaaaa R12: 0000000000000000 R13: ffffffff922a5f00 R14: 0000000000000001 R15: ffff981d3b698c2c FS: 00007f3678292740(0000) GS:ffff981d3fd80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000007c57a006 CR4: 00000000001606e0 Call Trace: __tcf_idr_release+0x79/0xf0 tcf_skbmod_init+0x1d1/0x210 [act_skbmod] tcf_action_init_1+0x2cc/0x430 tcf_action_init+0xd3/0x1b0 tc_ctl_action+0x18b/0x240 rtnetlink_rcv_msg+0x29c/0x310 ? _cond_resched+0x15/0x30 ? __kmalloc_node_track_caller+0x1b9/0x270 ? rtnl_calcit.isra.28+0x100/0x100 netlink_rcv_skb+0xd2/0x110 netlink_unicast+0x17c/0x230 netlink_sendmsg+0x2cd/0x3c0 sock_sendmsg+0x30/0x40 ___sys_sendmsg+0x27a/0x290 ? filemap_map_pages+0x34a/0x3a0 ? __handle_mm_fault+0xbfd/0xe20 __sys_sendmsg+0x51/0x90 do_syscall_64+0x6e/0x1a0 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x7f36776a3ba0 RSP: 002b:00007fff4703b618 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007fff4703b740 RCX: 00007f36776a3ba0 RDX: 0000000000000000 RSI: 00007fff4703b690 RDI: 0000000000000003 RBP: 000000005aaaba36 R08: 0000000000000002 R09: 0000000000000000 R10: 00007fff4703b0a0 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fff4703b754 R14: 0000000000000001 R15: 0000000000669f60 Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89 RIP: __call_rcu+0x23/0x2b0 RSP: ffffbd2e403e7798 CR2: 0000000000000008 Fix it in tcf_skbmod_cleanup(), ensuring that kfree_rcu(p, ...) is called only when p is not NULL. Fixes: 86da71b57383 ("net_sched: Introduce skbmod action") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 02:00:57 +03:00
if (p)
kfree_rcu(p, rcu);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
static int tcf_skbmod_dump(struct sk_buff *skb, struct tc_action *a,
int bind, int ref)
{
struct tcf_skbmod *d = to_skbmod(a);
unsigned char *b = skb_tail_pointer(skb);
struct tcf_skbmod_params *p = rtnl_dereference(d->skbmod_p);
struct tc_skbmod opt = {
.index = d->tcf_index,
net: sched: change type of reference and bind counters Change type of action reference counter to refcount_t. Change type of action bind counter to atomic_t. This type is used to allow decrementing bind counter without testing for 0 result. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:24 +03:00
.refcnt = refcount_read(&d->tcf_refcnt) - ref,
.bindcnt = atomic_read(&d->tcf_bindcnt) - bind,
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
.action = d->tcf_action,
};
struct tcf_t t;
opt.flags = p->flags;
if (nla_put(skb, TCA_SKBMOD_PARMS, sizeof(opt), &opt))
goto nla_put_failure;
if ((p->flags & SKBMOD_F_DMAC) &&
nla_put(skb, TCA_SKBMOD_DMAC, ETH_ALEN, p->eth_dst))
goto nla_put_failure;
if ((p->flags & SKBMOD_F_SMAC) &&
nla_put(skb, TCA_SKBMOD_SMAC, ETH_ALEN, p->eth_src))
goto nla_put_failure;
if ((p->flags & SKBMOD_F_ETYPE) &&
nla_put_u16(skb, TCA_SKBMOD_ETYPE, ntohs(p->eth_type)))
goto nla_put_failure;
tcf_tm_dump(&t, &d->tcf_tm);
if (nla_put_64bit(skb, TCA_SKBMOD_TM, sizeof(t), &t, TCA_SKBMOD_PAD))
goto nla_put_failure;
return skb->len;
nla_put_failure:
nlmsg_trim(skb, b);
return -1;
}
static int tcf_skbmod_walker(struct net *net, struct sk_buff *skb,
struct netlink_callback *cb, int type,
net: sched: act: add extack for walk callback This patch adds extack support for act walker callback api. This prepares to handle extack support inside each specific act implementation. Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-15 18:54:58 +03:00
const struct tc_action_ops *ops,
struct netlink_ext_ack *extack)
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
{
struct tc_action_net *tn = net_generic(net, skbmod_net_id);
net: sched: act: handle extack in tcf_generic_walker This patch adds extack handling for a common used TC act function "tcf_generic_walker()" to add an extack message on failures. The tcf_generic_walker() function can fail if get a invalid command different than DEL and GET. The naming "action" here is wrong, the correct naming would be command. Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-15 18:54:59 +03:00
return tcf_generic_walker(tn, skb, cb, type, ops, extack);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
net: sched: act: add extack for lookup callback This patch adds extack support for act lookup callback api. This prepares to handle extack support inside each specific act implementation. Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-15 18:54:57 +03:00
static int tcf_skbmod_search(struct net *net, struct tc_action **a, u32 index,
struct netlink_ext_ack *extack)
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
{
struct tc_action_net *tn = net_generic(net, skbmod_net_id);
net/sched: Change act_api and act_xxx modules to use IDR Typically, each TC filter has its own action. All the actions of the same type are saved in its hash table. But the hash buckets are too small that it degrades to a list. And the performance is greatly affected. For example, it takes about 0m11.914s to insert 64K rules. If we convert the hash table to IDR, it only takes about 0m1.500s. The improvement is huge. But please note that the test result is based on previous patch that cls_flower uses IDR. Signed-off-by: Chris Mi <chrism@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-30 09:31:59 +03:00
return tcf_idr_search(tn, a, index);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
net: sched: add 'delete' function to action ops Extend action ops with 'delete' function. Each action type to implements its own delete function that doesn't depend on rtnl lock. Implement delete function that is required to delete actions without holding rtnl lock. Use action API function that atomically deletes action only if it is still in action idr. This implementation prevents concurrent threads from deleting same action twice. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:28 +03:00
static int tcf_skbmod_delete(struct net *net, u32 index)
{
struct tc_action_net *tn = net_generic(net, skbmod_net_id);
return tcf_idr_delete_index(tn, index);
}
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
static struct tc_action_ops act_skbmod_ops = {
.kind = "skbmod",
.type = TCA_ACT_SKBMOD,
.owner = THIS_MODULE,
.act = tcf_skbmod_run,
.dump = tcf_skbmod_dump,
.init = tcf_skbmod_init,
.cleanup = tcf_skbmod_cleanup,
.walk = tcf_skbmod_walker,
.lookup = tcf_skbmod_search,
net: sched: add 'delete' function to action ops Extend action ops with 'delete' function. Each action type to implements its own delete function that doesn't depend on rtnl lock. Implement delete function that is required to delete actions without holding rtnl lock. Use action API function that atomically deletes action only if it is still in action idr. This implementation prevents concurrent threads from deleting same action twice. Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-05 17:24:28 +03:00
.delete = tcf_skbmod_delete,
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
.size = sizeof(struct tcf_skbmod),
};
static __net_init int skbmod_init_net(struct net *net)
{
struct tc_action_net *tn = net_generic(net, skbmod_net_id);
Revert "net_sched: hold netns refcnt for each action" This reverts commit ceffcc5e254b450e6159f173e4538215cebf1b59. If we hold that refcnt, the netns can never be destroyed until all actions are destroyed by user, this breaks our netns design which we expect all actions are destroyed when we destroy the whole netns. Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-07 00:47:18 +03:00
return tc_action_net_init(tn, &act_skbmod_ops);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
net_sched: switch to exit_batch for action pernet ops Since we now hold RTNL lock in tc_action_net_exit(), it is good to batch them to speedup tc action dismantle. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-12 02:35:03 +03:00
static void __net_exit skbmod_exit_net(struct list_head *net_list)
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
{
net_sched: switch to exit_batch for action pernet ops Since we now hold RTNL lock in tc_action_net_exit(), it is good to batch them to speedup tc action dismantle. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-12 02:35:03 +03:00
tc_action_net_exit(net_list, skbmod_net_id);
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
}
static struct pernet_operations skbmod_net_ops = {
.init = skbmod_init_net,
net_sched: switch to exit_batch for action pernet ops Since we now hold RTNL lock in tc_action_net_exit(), it is good to batch them to speedup tc action dismantle. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-12 02:35:03 +03:00
.exit_batch = skbmod_exit_net,
net_sched: Introduce skbmod action This action is intended to be an upgrade from a usability perspective from pedit (as well as operational debugability). Compare this: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action pedit munge offset -14 u8 set 0x02 \ munge offset -13 u8 set 0x15 \ munge offset -12 u8 set 0x15 \ munge offset -11 u8 set 0x15 \ munge offset -10 u16 set 0x1515 \ pipe to: sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbmod dmac 02:15:15:15:15:15 Also try to do a MAC address swap with pedit or worse try to debug a policy with destination mac, source mac and etherype. Then make few rules out of those and you'll get my point. In the future common use cases on pedit can be migrated to this action (as an example different fields in ip v4/6, transports like tcp/udp/sctp etc). For this first cut, this allows modifying basic ethernet header. The most important ethernet use case at the moment is when redirecting or mirroring packets to a remote machine. The dst mac address needs a re-write so that it doesnt get dropped or confuse an interconnecting (learning) switch or dropped by a target machine (which looks at the dst mac). And at times when flipping back the packet a swap of the MAC addresses is needed. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13 03:13:09 +03:00
.id = &skbmod_net_id,
.size = sizeof(struct tc_action_net),
};
MODULE_AUTHOR("Jamal Hadi Salim, <jhs@mojatatu.com>");
MODULE_DESCRIPTION("SKB data mod-ing");
MODULE_LICENSE("GPL");
static int __init skbmod_init_module(void)
{
return tcf_register_action(&act_skbmod_ops, &skbmod_net_ops);
}
static void __exit skbmod_cleanup_module(void)
{
tcf_unregister_action(&act_skbmod_ops, &skbmod_net_ops);
}
module_init(skbmod_init_module);
module_exit(skbmod_cleanup_module);