WSL2-Linux-Kernel/drivers/net/dsa/mv88e6060.c

267 строки
6.4 KiB
C
Исходник Обычный вид История

/*
* net/dsa/mv88e6060.c - Driver for Marvell 88e6060 switch chips
dsa: add switch chip cascading support The initial version of the DSA driver only supported a single switch chip per network interface, while DSA-capable switch chips can be interconnected to form a tree of switch chips. This patch adds support for multiple switch chips on a network interface. An example topology for a 16-port device with an embedded CPU is as follows: +-----+ +--------+ +--------+ | |eth0 10| switch |9 10| switch | | CPU +----------+ +-------+ | | | | chip 0 | | chip 1 | +-----+ +---++---+ +---++---+ || || || || ||1000baseT ||1000baseT ||ports 1-8 ||ports 9-16 This requires a couple of interdependent changes in the DSA layer: - The dsa platform driver data needs to be extended: there is still only one netdevice per DSA driver instance (eth0 in the example above), but each of the switch chips in the tree needs its own mii_bus device pointer, MII management bus address, and port name array. (include/net/dsa.h) The existing in-tree dsa users need some small changes to deal with this. (arch/arm) - The DSA and Ethertype DSA tagging modules need to be extended to use the DSA device ID field on receive and demultiplex the packet accordingly, and fill in the DSA device ID field on transmit according to which switch chip the packet is heading to. (net/dsa/tag_{dsa,edsa}.c) - The concept of "CPU port", which is the switch chip port that the CPU is connected to (port 10 on switch chip 0 in the example), needs to be extended with the concept of "upstream port", which is the port on the switch chip that will bring us one hop closer to the CPU (port 10 for both switch chips in the example above). - The dsa platform data needs to specify which ports on which switch chips are links to other switch chips, so that we can enable DSA tagging mode on them. (For inter-switch links, we always use non-EtherType DSA tagging, since it has lower overhead. The CPU link uses dsa or edsa tagging depending on what the 'root' switch chip supports.) This is done by specifying "dsa" for the given port in the port array. - The dsa platform data needs to be extended with information on via which port to reach any given switch chip from any given switch chip. This info is specified via the per-switch chip data struct ->rtable[] array, which gives the nexthop ports for each of the other switches in the tree. For the example topology above, the dsa platform data would look something like this: static struct dsa_chip_data sw[2] = { { .mii_bus = &foo, .sw_addr = 1, .port_names[0] = "p1", .port_names[1] = "p2", .port_names[2] = "p3", .port_names[3] = "p4", .port_names[4] = "p5", .port_names[5] = "p6", .port_names[6] = "p7", .port_names[7] = "p8", .port_names[9] = "dsa", .port_names[10] = "cpu", .rtable = (s8 []){ -1, 9, }, }, { .mii_bus = &foo, .sw_addr = 2, .port_names[0] = "p9", .port_names[1] = "p10", .port_names[2] = "p11", .port_names[3] = "p12", .port_names[4] = "p13", .port_names[5] = "p14", .port_names[6] = "p15", .port_names[7] = "p16", .port_names[10] = "dsa", .rtable = (s8 []){ 10, -1, }, }, }, static struct dsa_platform_data pd = { .netdev = &foo, .nr_switches = 2, .sw = sw, }; Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Gary Thomas <gary@mlbassoc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 12:52:09 +03:00
* Copyright (c) 2008-2009 Marvell Semiconductor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/phy.h>
#include <net/dsa.h>
#include "mv88e6060.h"
static int reg_read(struct dsa_switch *ds, int addr, int reg)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(ds->master_dev);
if (bus == NULL)
return -EINVAL;
return mdiobus_read_nested(bus, ds->pd->sw_addr + addr, reg);
}
#define REG_READ(addr, reg) \
({ \
int __ret; \
\
__ret = reg_read(ds, addr, reg); \
if (__ret < 0) \
return __ret; \
__ret; \
})
static int reg_write(struct dsa_switch *ds, int addr, int reg, u16 val)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(ds->master_dev);
if (bus == NULL)
return -EINVAL;
return mdiobus_write_nested(bus, ds->pd->sw_addr + addr, reg, val);
}
#define REG_WRITE(addr, reg, val) \
({ \
int __ret; \
\
__ret = reg_write(ds, addr, reg, val); \
if (__ret < 0) \
return __ret; \
})
static char *mv88e6060_probe(struct device *dsa_dev, struct device *host_dev,
int sw_addr, void **priv)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
int ret;
*priv = NULL;
if (bus == NULL)
return NULL;
ret = mdiobus_read(bus, sw_addr + REG_PORT(0), PORT_SWITCH_ID);
if (ret >= 0) {
if (ret == PORT_SWITCH_ID_6060)
return "Marvell 88E6060 (A0)";
if (ret == PORT_SWITCH_ID_6060_R1 ||
ret == PORT_SWITCH_ID_6060_R2)
return "Marvell 88E6060 (B0)";
if ((ret & PORT_SWITCH_ID_6060_MASK) == PORT_SWITCH_ID_6060)
return "Marvell 88E6060";
}
return NULL;
}
static int mv88e6060_switch_reset(struct dsa_switch *ds)
{
int i;
int ret;
unsigned long timeout;
/* Set all ports to the disabled state. */
for (i = 0; i < MV88E6060_PORTS; i++) {
ret = REG_READ(REG_PORT(i), PORT_CONTROL);
REG_WRITE(REG_PORT(i), PORT_CONTROL,
ret & ~PORT_CONTROL_STATE_MASK);
}
/* Wait for transmit queues to drain. */
usleep_range(2000, 4000);
/* Reset the switch. */
REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL,
GLOBAL_ATU_CONTROL_SWRESET |
GLOBAL_ATU_CONTROL_ATUSIZE_1024 |
GLOBAL_ATU_CONTROL_ATE_AGE_5MIN);
/* Wait up to one second for reset to complete. */
timeout = jiffies + 1 * HZ;
while (time_before(jiffies, timeout)) {
ret = REG_READ(REG_GLOBAL, GLOBAL_STATUS);
if (ret & GLOBAL_STATUS_INIT_READY)
break;
usleep_range(1000, 2000);
}
if (time_after(jiffies, timeout))
return -ETIMEDOUT;
return 0;
}
static int mv88e6060_setup_global(struct dsa_switch *ds)
{
/* Disable discarding of frames with excessive collisions,
* set the maximum frame size to 1536 bytes, and mask all
* interrupt sources.
*/
REG_WRITE(REG_GLOBAL, GLOBAL_CONTROL, GLOBAL_CONTROL_MAX_FRAME_1536);
/* Enable automatic address learning, set the address
* database size to 1024 entries, and set the default aging
* time to 5 minutes.
*/
REG_WRITE(REG_GLOBAL, GLOBAL_ATU_CONTROL,
GLOBAL_ATU_CONTROL_ATUSIZE_1024 |
GLOBAL_ATU_CONTROL_ATE_AGE_5MIN);
return 0;
}
static int mv88e6060_setup_port(struct dsa_switch *ds, int p)
{
int addr = REG_PORT(p);
/* Do not force flow control, disable Ingress and Egress
* Header tagging, disable VLAN tunneling, and set the port
* state to Forwarding. Additionally, if this is the CPU
* port, enable Ingress and Egress Trailer tagging mode.
*/
REG_WRITE(addr, PORT_CONTROL,
dsa_is_cpu_port(ds, p) ?
PORT_CONTROL_TRAILER |
PORT_CONTROL_INGRESS_MODE |
PORT_CONTROL_STATE_FORWARDING :
PORT_CONTROL_STATE_FORWARDING);
/* Port based VLAN map: give each port its own address
* database, allow the CPU port to talk to each of the 'real'
* ports, and allow each of the 'real' ports to only talk to
* the CPU port.
*/
REG_WRITE(addr, PORT_VLAN_MAP,
((p & 0xf) << PORT_VLAN_MAP_DBNUM_SHIFT) |
(dsa_is_cpu_port(ds, p) ?
ds->phys_port_mask :
BIT(ds->dst->cpu_port)));
/* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
*/
REG_WRITE(addr, PORT_ASSOC_VECTOR, BIT(p));
return 0;
}
static int mv88e6060_setup(struct dsa_switch *ds)
{
int i;
int ret;
ret = mv88e6060_switch_reset(ds);
if (ret < 0)
return ret;
/* @@@ initialise atu */
ret = mv88e6060_setup_global(ds);
if (ret < 0)
return ret;
for (i = 0; i < MV88E6060_PORTS; i++) {
ret = mv88e6060_setup_port(ds, i);
if (ret < 0)
return ret;
}
return 0;
}
static int mv88e6060_set_addr(struct dsa_switch *ds, u8 *addr)
{
/* Use the same MAC Address as FD Pause frames for all ports */
REG_WRITE(REG_GLOBAL, GLOBAL_MAC_01, (addr[0] << 9) | addr[1]);
REG_WRITE(REG_GLOBAL, GLOBAL_MAC_23, (addr[2] << 8) | addr[3]);
REG_WRITE(REG_GLOBAL, GLOBAL_MAC_45, (addr[4] << 8) | addr[5]);
return 0;
}
static int mv88e6060_port_to_phy_addr(int port)
{
if (port >= 0 && port < MV88E6060_PORTS)
return port;
return -1;
}
static int mv88e6060_phy_read(struct dsa_switch *ds, int port, int regnum)
{
int addr;
addr = mv88e6060_port_to_phy_addr(port);
if (addr == -1)
return 0xffff;
return reg_read(ds, addr, regnum);
}
static int
mv88e6060_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
{
int addr;
addr = mv88e6060_port_to_phy_addr(port);
if (addr == -1)
return 0xffff;
return reg_write(ds, addr, regnum, val);
}
static struct dsa_switch_driver mv88e6060_switch_driver = {
.tag_protocol = DSA_TAG_PROTO_TRAILER,
.probe = mv88e6060_probe,
.setup = mv88e6060_setup,
.set_addr = mv88e6060_set_addr,
.phy_read = mv88e6060_phy_read,
.phy_write = mv88e6060_phy_write,
};
static int __init mv88e6060_init(void)
{
register_switch_driver(&mv88e6060_switch_driver);
return 0;
}
module_init(mv88e6060_init);
static void __exit mv88e6060_cleanup(void)
{
unregister_switch_driver(&mv88e6060_switch_driver);
}
module_exit(mv88e6060_cleanup);
MODULE_AUTHOR("Lennert Buytenhek <buytenh@wantstofly.org>");
MODULE_DESCRIPTION("Driver for Marvell 88E6060 ethernet switch chip");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:mv88e6060");