2019-06-04 11:11:33 +03:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-only
|
2009-01-15 11:42:56 +03:00
|
|
|
/*
|
|
|
|
* linux/arch/arm/plat-pxa/mfp.c
|
|
|
|
*
|
|
|
|
* Multi-Function Pin Support
|
|
|
|
*
|
|
|
|
* Copyright (C) 2007 Marvell Internation Ltd.
|
|
|
|
*
|
|
|
|
* 2007-08-21: eric miao <eric.miao@marvell.com>
|
|
|
|
* initial version
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
#include <linux/init.h>
|
|
|
|
#include <linux/io.h>
|
|
|
|
|
|
|
|
#include <plat/mfp.h>
|
|
|
|
|
|
|
|
#define MFPR_SIZE (PAGE_SIZE)
|
|
|
|
|
|
|
|
/* MFPR register bit definitions */
|
|
|
|
#define MFPR_PULL_SEL (0x1 << 15)
|
|
|
|
#define MFPR_PULLUP_EN (0x1 << 14)
|
|
|
|
#define MFPR_PULLDOWN_EN (0x1 << 13)
|
|
|
|
#define MFPR_SLEEP_SEL (0x1 << 9)
|
|
|
|
#define MFPR_SLEEP_OE_N (0x1 << 7)
|
|
|
|
#define MFPR_EDGE_CLEAR (0x1 << 6)
|
|
|
|
#define MFPR_EDGE_FALL_EN (0x1 << 5)
|
|
|
|
#define MFPR_EDGE_RISE_EN (0x1 << 4)
|
|
|
|
|
|
|
|
#define MFPR_SLEEP_DATA(x) ((x) << 8)
|
|
|
|
#define MFPR_DRIVE(x) (((x) & 0x7) << 10)
|
|
|
|
#define MFPR_AF_SEL(x) (((x) & 0x7) << 0)
|
|
|
|
|
|
|
|
#define MFPR_EDGE_NONE (0)
|
|
|
|
#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN)
|
|
|
|
#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN)
|
|
|
|
#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL)
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Table that determines the low power modes outputs, with actual settings
|
|
|
|
* used in parentheses for don't-care values. Except for the float output,
|
|
|
|
* the configured driven and pulled levels match, so if there is a need for
|
|
|
|
* non-LPM pulled output, the same configuration could probably be used.
|
|
|
|
*
|
|
|
|
* Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
|
|
|
|
* (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
|
|
|
|
*
|
|
|
|
* Input 0 X(0) X(0) X(0) 0
|
|
|
|
* Drive 0 0 0 0 X(1) 0
|
|
|
|
* Drive 1 0 1 X(1) 0 0
|
|
|
|
* Pull hi (1) 1 X(1) 1 0 0
|
|
|
|
* Pull lo (0) 1 X(0) 0 1 0
|
|
|
|
* Z (float) 1 X(0) 0 0 0
|
|
|
|
*/
|
|
|
|
#define MFPR_LPM_INPUT (0)
|
|
|
|
#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
|
|
|
|
#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
|
|
|
|
#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N)
|
|
|
|
#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
|
|
|
|
#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N)
|
|
|
|
#define MFPR_LPM_MASK (0xe080)
|
|
|
|
|
|
|
|
/*
|
|
|
|
* The pullup and pulldown state of the MFP pin at run mode is by default
|
|
|
|
* determined by the selected alternate function. In case that some buggy
|
|
|
|
* devices need to override this default behavior, the definitions below
|
|
|
|
* indicates the setting of corresponding MFPR bits
|
|
|
|
*
|
|
|
|
* Definition pull_sel pullup_en pulldown_en
|
|
|
|
* MFPR_PULL_NONE 0 0 0
|
|
|
|
* MFPR_PULL_LOW 1 0 1
|
|
|
|
* MFPR_PULL_HIGH 1 1 0
|
|
|
|
* MFPR_PULL_BOTH 1 1 1
|
2009-08-11 16:39:09 +04:00
|
|
|
* MFPR_PULL_FLOAT 1 0 0
|
2009-01-15 11:42:56 +03:00
|
|
|
*/
|
|
|
|
#define MFPR_PULL_NONE (0)
|
|
|
|
#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
|
|
|
|
#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
|
|
|
|
#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
|
2009-08-11 16:39:09 +04:00
|
|
|
#define MFPR_PULL_FLOAT (MFPR_PULL_SEL)
|
2009-01-15 11:42:56 +03:00
|
|
|
|
|
|
|
/* mfp_spin_lock is used to ensure that MFP register configuration
|
|
|
|
* (most likely a read-modify-write operation) is atomic, and that
|
|
|
|
* mfp_table[] is consistent
|
|
|
|
*/
|
|
|
|
static DEFINE_SPINLOCK(mfp_spin_lock);
|
|
|
|
|
|
|
|
static void __iomem *mfpr_mmio_base;
|
|
|
|
|
|
|
|
struct mfp_pin {
|
|
|
|
unsigned long config; /* -1 for not configured */
|
|
|
|
unsigned long mfpr_off; /* MFPRxx Register offset */
|
|
|
|
unsigned long mfpr_run; /* Run-Mode Register Value */
|
|
|
|
unsigned long mfpr_lpm; /* Low Power Mode Register Value */
|
|
|
|
};
|
|
|
|
|
|
|
|
static struct mfp_pin mfp_table[MFP_PIN_MAX];
|
|
|
|
|
|
|
|
/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
|
|
|
|
static const unsigned long mfpr_lpm[] = {
|
|
|
|
MFPR_LPM_INPUT,
|
|
|
|
MFPR_LPM_DRIVE_LOW,
|
|
|
|
MFPR_LPM_DRIVE_HIGH,
|
|
|
|
MFPR_LPM_PULL_LOW,
|
|
|
|
MFPR_LPM_PULL_HIGH,
|
|
|
|
MFPR_LPM_FLOAT,
|
2010-04-27 07:14:24 +04:00
|
|
|
MFPR_LPM_INPUT,
|
2009-01-15 11:42:56 +03:00
|
|
|
};
|
|
|
|
|
|
|
|
/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
|
|
|
|
static const unsigned long mfpr_pull[] = {
|
|
|
|
MFPR_PULL_NONE,
|
|
|
|
MFPR_PULL_LOW,
|
|
|
|
MFPR_PULL_HIGH,
|
|
|
|
MFPR_PULL_BOTH,
|
2009-08-11 16:39:09 +04:00
|
|
|
MFPR_PULL_FLOAT,
|
2009-01-15 11:42:56 +03:00
|
|
|
};
|
|
|
|
|
|
|
|
/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
|
|
|
|
static const unsigned long mfpr_edge[] = {
|
|
|
|
MFPR_EDGE_NONE,
|
|
|
|
MFPR_EDGE_RISE,
|
|
|
|
MFPR_EDGE_FALL,
|
|
|
|
MFPR_EDGE_BOTH,
|
|
|
|
};
|
|
|
|
|
|
|
|
#define mfpr_readl(off) \
|
|
|
|
__raw_readl(mfpr_mmio_base + (off))
|
|
|
|
|
|
|
|
#define mfpr_writel(off, val) \
|
|
|
|
__raw_writel(val, mfpr_mmio_base + (off))
|
|
|
|
|
|
|
|
#define mfp_configured(p) ((p)->config != -1)
|
|
|
|
|
|
|
|
/*
|
2011-01-19 17:18:54 +03:00
|
|
|
* perform a read-back of any valid MFPR register to make sure the
|
2009-01-15 11:42:56 +03:00
|
|
|
* previous writings are finished
|
|
|
|
*/
|
2011-01-19 17:18:54 +03:00
|
|
|
static unsigned long mfpr_off_readback;
|
|
|
|
#define mfpr_sync() (void)__raw_readl(mfpr_mmio_base + mfpr_off_readback)
|
2009-01-15 11:42:56 +03:00
|
|
|
|
|
|
|
static inline void __mfp_config_run(struct mfp_pin *p)
|
|
|
|
{
|
|
|
|
if (mfp_configured(p))
|
|
|
|
mfpr_writel(p->mfpr_off, p->mfpr_run);
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline void __mfp_config_lpm(struct mfp_pin *p)
|
|
|
|
{
|
|
|
|
if (mfp_configured(p)) {
|
|
|
|
unsigned long mfpr_clr = (p->mfpr_run & ~MFPR_EDGE_BOTH) | MFPR_EDGE_CLEAR;
|
|
|
|
if (mfpr_clr != p->mfpr_run)
|
|
|
|
mfpr_writel(p->mfpr_off, mfpr_clr);
|
|
|
|
if (p->mfpr_lpm != mfpr_clr)
|
|
|
|
mfpr_writel(p->mfpr_off, p->mfpr_lpm);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
void mfp_config(unsigned long *mfp_cfgs, int num)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
int i;
|
|
|
|
|
|
|
|
spin_lock_irqsave(&mfp_spin_lock, flags);
|
|
|
|
|
|
|
|
for (i = 0; i < num; i++, mfp_cfgs++) {
|
|
|
|
unsigned long tmp, c = *mfp_cfgs;
|
|
|
|
struct mfp_pin *p;
|
|
|
|
int pin, af, drv, lpm, edge, pull;
|
|
|
|
|
|
|
|
pin = MFP_PIN(c);
|
|
|
|
BUG_ON(pin >= MFP_PIN_MAX);
|
|
|
|
p = &mfp_table[pin];
|
|
|
|
|
|
|
|
af = MFP_AF(c);
|
|
|
|
drv = MFP_DS(c);
|
|
|
|
lpm = MFP_LPM_STATE(c);
|
|
|
|
edge = MFP_LPM_EDGE(c);
|
|
|
|
pull = MFP_PULL(c);
|
|
|
|
|
|
|
|
/* run-mode pull settings will conflict with MFPR bits of
|
|
|
|
* low power mode state, calculate mfpr_run and mfpr_lpm
|
|
|
|
* individually if pull != MFP_PULL_NONE
|
|
|
|
*/
|
|
|
|
tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
|
|
|
|
|
|
|
|
if (likely(pull == MFP_PULL_NONE)) {
|
|
|
|
p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
|
|
|
|
p->mfpr_lpm = p->mfpr_run;
|
|
|
|
} else {
|
|
|
|
p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
|
|
|
|
p->mfpr_run = tmp | mfpr_pull[pull];
|
|
|
|
}
|
|
|
|
|
|
|
|
p->config = c; __mfp_config_run(p);
|
|
|
|
}
|
|
|
|
|
|
|
|
mfpr_sync();
|
|
|
|
spin_unlock_irqrestore(&mfp_spin_lock, flags);
|
|
|
|
}
|
|
|
|
|
|
|
|
unsigned long mfp_read(int mfp)
|
|
|
|
{
|
|
|
|
unsigned long val, flags;
|
|
|
|
|
2009-11-13 13:37:34 +03:00
|
|
|
BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
|
2009-01-15 11:42:56 +03:00
|
|
|
|
|
|
|
spin_lock_irqsave(&mfp_spin_lock, flags);
|
|
|
|
val = mfpr_readl(mfp_table[mfp].mfpr_off);
|
|
|
|
spin_unlock_irqrestore(&mfp_spin_lock, flags);
|
|
|
|
|
|
|
|
return val;
|
|
|
|
}
|
|
|
|
|
|
|
|
void mfp_write(int mfp, unsigned long val)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
2009-11-13 13:37:34 +03:00
|
|
|
BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
|
2009-01-15 11:42:56 +03:00
|
|
|
|
|
|
|
spin_lock_irqsave(&mfp_spin_lock, flags);
|
|
|
|
mfpr_writel(mfp_table[mfp].mfpr_off, val);
|
|
|
|
mfpr_sync();
|
|
|
|
spin_unlock_irqrestore(&mfp_spin_lock, flags);
|
|
|
|
}
|
|
|
|
|
2011-10-02 00:03:45 +04:00
|
|
|
void __init mfp_init_base(void __iomem *mfpr_base)
|
2009-01-15 11:42:56 +03:00
|
|
|
{
|
|
|
|
int i;
|
|
|
|
|
|
|
|
/* initialize the table with default - unconfigured */
|
|
|
|
for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
|
|
|
|
mfp_table[i].config = -1;
|
|
|
|
|
2011-10-02 00:03:45 +04:00
|
|
|
mfpr_mmio_base = mfpr_base;
|
2009-01-15 11:42:56 +03:00
|
|
|
}
|
|
|
|
|
|
|
|
void __init mfp_init_addr(struct mfp_addr_map *map)
|
|
|
|
{
|
|
|
|
struct mfp_addr_map *p;
|
|
|
|
unsigned long offset, flags;
|
|
|
|
int i;
|
|
|
|
|
|
|
|
spin_lock_irqsave(&mfp_spin_lock, flags);
|
|
|
|
|
2011-01-19 17:18:54 +03:00
|
|
|
/* mfp offset for readback */
|
|
|
|
mfpr_off_readback = map[0].offset;
|
|
|
|
|
2009-01-15 11:42:56 +03:00
|
|
|
for (p = map; p->start != MFP_PIN_INVALID; p++) {
|
|
|
|
offset = p->offset;
|
|
|
|
i = p->start;
|
|
|
|
|
|
|
|
do {
|
|
|
|
mfp_table[i].mfpr_off = offset;
|
|
|
|
mfp_table[i].mfpr_run = 0;
|
|
|
|
mfp_table[i].mfpr_lpm = 0;
|
|
|
|
offset += 4; i++;
|
|
|
|
} while ((i <= p->end) && (p->end != -1));
|
|
|
|
}
|
|
|
|
|
|
|
|
spin_unlock_irqrestore(&mfp_spin_lock, flags);
|
|
|
|
}
|
|
|
|
|
|
|
|
void mfp_config_lpm(void)
|
|
|
|
{
|
|
|
|
struct mfp_pin *p = &mfp_table[0];
|
|
|
|
int pin;
|
|
|
|
|
|
|
|
for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
|
|
|
|
__mfp_config_lpm(p);
|
|
|
|
}
|
|
|
|
|
|
|
|
void mfp_config_run(void)
|
|
|
|
{
|
|
|
|
struct mfp_pin *p = &mfp_table[0];
|
|
|
|
int pin;
|
|
|
|
|
|
|
|
for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
|
|
|
|
__mfp_config_run(p);
|
|
|
|
}
|