WSL2-Linux-Kernel/drivers/ata/sata_uli.c

287 строки
7.4 KiB
C
Исходник Обычный вид История

/*
* sata_uli.c - ULi Electronics SATA
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* Hardware documentation available under NDA.
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "sata_uli"
#define DRV_VERSION "1.2"
enum {
uli_5289 = 0,
uli_5287 = 1,
uli_5281 = 2,
uli_max_ports = 4,
/* PCI configuration registers */
ULI5287_BASE = 0x90, /* sata0 phy SCR registers */
ULI5287_OFFS = 0x10, /* offset from sata0->sata1 phy regs */
ULI5281_BASE = 0x60, /* sata0 phy SCR registers */
ULI5281_OFFS = 0x60, /* offset from sata0->sata1 phy regs */
};
struct uli_priv {
unsigned int scr_cfg_addr[uli_max_ports];
};
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id uli_pci_tbl[] = {
{ PCI_VDEVICE(AL, 0x5289), uli_5289 },
{ PCI_VDEVICE(AL, 0x5287), uli_5287 },
{ PCI_VDEVICE(AL, 0x5281), uli_5281 },
{ } /* terminate list */
};
static struct pci_driver uli_pci_driver = {
.name = DRV_NAME,
.id_table = uli_pci_tbl,
.probe = uli_init_one,
.remove = ata_pci_remove_one,
};
static struct scsi_host_template uli_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static const struct ata_port_operations uli_ops = {
.port_disable = ata_port_disable,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.scr_read = uli_scr_read,
.scr_write = uli_scr_write,
.port_start = ata_port_start,
};
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 14:43:58 +04:00
static const struct ata_port_info uli_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_IGN_SIMPLEX,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &uli_ops,
};
MODULE_AUTHOR("Peer Chen");
MODULE_DESCRIPTION("low-level driver for ULi Electronics SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, uli_pci_tbl);
MODULE_VERSION(DRV_VERSION);
static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
{
struct uli_priv *hpriv = ap->host->private_data;
return hpriv->scr_cfg_addr[ap->port_no] + (4 * sc_reg);
}
static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
u32 val;
pci_read_config_dword(pdev, cfg_addr, &val);
return val;
}
static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned int cfg_addr = get_scr_cfg_addr(ap, scr);
pci_write_config_dword(pdev, cfg_addr, val);
}
static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
return 0xffffffffU;
return uli_scr_cfg_read(ap, sc_reg);
}
static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
if (sc_reg > SCR_CONTROL) //SCR_CONTROL=2, SCR_ERROR=1, SCR_STATUS=0
return;
uli_scr_cfg_write(ap, sc_reg, val);
}
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
const struct ata_port_info *ppi[] = { &uli_port_info, NULL };
unsigned int board_idx = (unsigned int) ent->driver_data;
struct ata_host *host;
struct uli_priv *hpriv;
void __iomem * const *iomap;
struct ata_ioports *ioaddr;
int n_ports, rc;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
rc = pcim_enable_device(pdev);
if (rc)
return rc;
n_ports = 2;
if (board_idx == uli_5287)
n_ports = 4;
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 14:43:58 +04:00
/* allocate the host */
host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
if (!host)
return -ENOMEM;
hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
if (!hpriv)
return -ENOMEM;
host->private_data = hpriv;
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 14:43:58 +04:00
/* the first two ports are standard SFF */
rc = ata_pci_init_sff_host(host);
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 14:43:58 +04:00
if (rc)
return rc;
rc = ata_pci_init_bmdma(host);
if (rc)
return rc;
iomap = host->iomap;
switch (board_idx) {
case uli_5287:
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 14:43:58 +04:00
/* If there are four, the last two live right after
* the standard SFF ports.
*/
hpriv->scr_cfg_addr[0] = ULI5287_BASE;
hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
ioaddr = &host->ports[2]->ioaddr;
ioaddr->cmd_addr = iomap[0] + 8;
ioaddr->altstatus_addr =
ioaddr->ctl_addr = (void __iomem *)
((unsigned long)iomap[1] | ATA_PCI_CTL_OFS) + 4;
ioaddr->bmdma_addr = iomap[4] + 16;
hpriv->scr_cfg_addr[2] = ULI5287_BASE + ULI5287_OFFS*4;
ata_std_ports(ioaddr);
ioaddr = &host->ports[3]->ioaddr;
ioaddr->cmd_addr = iomap[2] + 8;
ioaddr->altstatus_addr =
ioaddr->ctl_addr = (void __iomem *)
((unsigned long)iomap[3] | ATA_PCI_CTL_OFS) + 4;
ioaddr->bmdma_addr = iomap[4] + 24;
hpriv->scr_cfg_addr[3] = ULI5287_BASE + ULI5287_OFFS*5;
ata_std_ports(ioaddr);
break;
case uli_5289:
hpriv->scr_cfg_addr[0] = ULI5287_BASE;
hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
break;
case uli_5281:
hpriv->scr_cfg_addr[0] = ULI5281_BASE;
hpriv->scr_cfg_addr[1] = ULI5281_BASE + ULI5281_OFFS;
break;
default:
BUG();
break;
}
pci_set_master(pdev);
pci_intx(pdev, 1);
return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
&uli_sht);
}
static int __init uli_init(void)
{
return pci_register_driver(&uli_pci_driver);
}
static void __exit uli_exit(void)
{
pci_unregister_driver(&uli_pci_driver);
}
module_init(uli_init);
module_exit(uli_exit);