WSL2-Linux-Kernel/kernel/trace/ftrace.c

1402 строки
29 KiB
C
Исходник Обычный вид История

/*
* Infrastructure for profiling code inserted by 'gcc -pg'.
*
* Copyright (C) 2007-2008 Steven Rostedt <srostedt@redhat.com>
* Copyright (C) 2004-2008 Ingo Molnar <mingo@redhat.com>
*
* Originally ported from the -rt patch by:
* Copyright (C) 2007 Arnaldo Carvalho de Melo <acme@redhat.com>
*
* Based on code in the latency_tracer, that is:
*
* Copyright (C) 2004-2006 Ingo Molnar
* Copyright (C) 2004 William Lee Irwin III
*/
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#include <linux/stop_machine.h>
#include <linux/clocksource.h>
#include <linux/kallsyms.h>
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
#include <linux/seq_file.h>
#include <linux/debugfs.h>
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#include <linux/kthread.h>
#include <linux/hardirq.h>
#include <linux/ftrace.h>
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
#include <linux/uaccess.h>
#include <linux/sysctl.h>
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#include <linux/hash.h>
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
#include <linux/ctype.h>
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#include <linux/list.h>
#include "trace.h"
/* ftrace_enabled is a method to turn ftrace on or off */
int ftrace_enabled __read_mostly;
static int last_ftrace_enabled;
/*
* ftrace_disabled is set when an anomaly is discovered.
* ftrace_disabled is much stronger than ftrace_enabled.
*/
static int ftrace_disabled __read_mostly;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
static DEFINE_SPINLOCK(ftrace_lock);
static DEFINE_MUTEX(ftrace_sysctl_lock);
static struct ftrace_ops ftrace_list_end __read_mostly =
{
.func = ftrace_stub,
};
static struct ftrace_ops *ftrace_list __read_mostly = &ftrace_list_end;
ftrace_func_t ftrace_trace_function __read_mostly = ftrace_stub;
/* mcount is defined per arch in assembly */
EXPORT_SYMBOL(mcount);
void ftrace_list_func(unsigned long ip, unsigned long parent_ip)
{
struct ftrace_ops *op = ftrace_list;
/* in case someone actually ports this to alpha! */
read_barrier_depends();
while (op != &ftrace_list_end) {
/* silly alpha */
read_barrier_depends();
op->func(ip, parent_ip);
op = op->next;
};
}
/**
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
* clear_ftrace_function - reset the ftrace function
*
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
* This NULLs the ftrace function and in essence stops
* tracing. There may be lag
*/
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
void clear_ftrace_function(void)
{
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_trace_function = ftrace_stub;
}
static int __register_ftrace_function(struct ftrace_ops *ops)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
/* Should never be called by interrupts */
spin_lock(&ftrace_lock);
ops->next = ftrace_list;
/*
* We are entering ops into the ftrace_list but another
* CPU might be walking that list. We need to make sure
* the ops->next pointer is valid before another CPU sees
* the ops pointer included into the ftrace_list.
*/
smp_wmb();
ftrace_list = ops;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (ftrace_enabled) {
/*
* For one func, simply call it directly.
* For more than one func, call the chain.
*/
if (ops->next == &ftrace_list_end)
ftrace_trace_function = ops->func;
else
ftrace_trace_function = ftrace_list_func;
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
spin_unlock(&ftrace_lock);
return 0;
}
static int __unregister_ftrace_function(struct ftrace_ops *ops)
{
struct ftrace_ops **p;
int ret = 0;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
spin_lock(&ftrace_lock);
/*
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
* If we are removing the last function, then simply point
* to the ftrace_stub.
*/
if (ftrace_list == ops && ops->next == &ftrace_list_end) {
ftrace_trace_function = ftrace_stub;
ftrace_list = &ftrace_list_end;
goto out;
}
for (p = &ftrace_list; *p != &ftrace_list_end; p = &(*p)->next)
if (*p == ops)
break;
if (*p != ops) {
ret = -1;
goto out;
}
*p = (*p)->next;
if (ftrace_enabled) {
/* If we only have one func left, then call that directly */
if (ftrace_list == &ftrace_list_end ||
ftrace_list->next == &ftrace_list_end)
ftrace_trace_function = ftrace_list->func;
}
out:
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
spin_unlock(&ftrace_lock);
return ret;
}
#ifdef CONFIG_DYNAMIC_FTRACE
static struct task_struct *ftraced_task;
static DECLARE_WAIT_QUEUE_HEAD(ftraced_waiters);
static unsigned long ftraced_iteration_counter;
enum {
FTRACE_ENABLE_CALLS = (1 << 0),
FTRACE_DISABLE_CALLS = (1 << 1),
FTRACE_UPDATE_TRACE_FUNC = (1 << 2),
FTRACE_ENABLE_MCOUNT = (1 << 3),
FTRACE_DISABLE_MCOUNT = (1 << 4),
};
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
static int ftrace_filtered;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
static struct hlist_head ftrace_hash[FTRACE_HASHSIZE];
static DEFINE_PER_CPU(int, ftrace_shutdown_disable_cpu);
static DEFINE_SPINLOCK(ftrace_shutdown_lock);
static DEFINE_MUTEX(ftraced_lock);
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
static DEFINE_MUTEX(ftrace_filter_lock);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
struct ftrace_page {
struct ftrace_page *next;
int index;
struct dyn_ftrace records[];
} __attribute__((packed));
#define ENTRIES_PER_PAGE \
((PAGE_SIZE - sizeof(struct ftrace_page)) / sizeof(struct dyn_ftrace))
/* estimate from running different kernels */
#define NR_TO_INIT 10000
static struct ftrace_page *ftrace_pages_start;
static struct ftrace_page *ftrace_pages;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
static int ftraced_trigger;
static int ftraced_suspend;
static int ftrace_record_suspend;
static struct dyn_ftrace *ftrace_free_records;
static inline int
ftrace_ip_in_hash(unsigned long ip, unsigned long key)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
struct dyn_ftrace *p;
struct hlist_node *t;
int found = 0;
hlist_for_each_entry(p, t, &ftrace_hash[key], node) {
if (p->ip == ip) {
found = 1;
break;
}
}
return found;
}
static inline void
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_add_hash(struct dyn_ftrace *node, unsigned long key)
{
hlist_add_head(&node->node, &ftrace_hash[key]);
}
static void ftrace_free_rec(struct dyn_ftrace *rec)
{
/* no locking, only called from kstop_machine */
rec->ip = (unsigned long)ftrace_free_records;
ftrace_free_records = rec;
rec->flags |= FTRACE_FL_FREE;
}
static struct dyn_ftrace *ftrace_alloc_dyn_node(unsigned long ip)
{
struct dyn_ftrace *rec;
/* First check for freed records */
if (ftrace_free_records) {
rec = ftrace_free_records;
if (unlikely(!(rec->flags & FTRACE_FL_FREE))) {
WARN_ON_ONCE(1);
ftrace_free_records = NULL;
ftrace_disabled = 1;
ftrace_enabled = 0;
return NULL;
}
ftrace_free_records = (void *)rec->ip;
memset(rec, 0, sizeof(*rec));
return rec;
}
if (ftrace_pages->index == ENTRIES_PER_PAGE) {
if (!ftrace_pages->next)
return NULL;
ftrace_pages = ftrace_pages->next;
}
return &ftrace_pages->records[ftrace_pages->index++];
}
static void
ftrace_record_ip(unsigned long ip)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
struct dyn_ftrace *node;
unsigned long flags;
unsigned long key;
int resched;
int atomic;
int cpu;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (!ftrace_enabled || ftrace_disabled)
return;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
resched = need_resched();
preempt_disable_notrace();
/*
* We simply need to protect against recursion.
* Use the the raw version of smp_processor_id and not
* __get_cpu_var which can call debug hooks that can
* cause a recursive crash here.
*/
cpu = raw_smp_processor_id();
per_cpu(ftrace_shutdown_disable_cpu, cpu)++;
if (per_cpu(ftrace_shutdown_disable_cpu, cpu) != 1)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
goto out;
if (unlikely(ftrace_record_suspend))
goto out;
key = hash_long(ip, FTRACE_HASHBITS);
WARN_ON_ONCE(key >= FTRACE_HASHSIZE);
if (ftrace_ip_in_hash(ip, key))
goto out;
atomic = irqs_disabled();
spin_lock_irqsave(&ftrace_shutdown_lock, flags);
/* This ip may have hit the hash before the lock */
if (ftrace_ip_in_hash(ip, key))
goto out_unlock;
/*
* There's a slight race that the ftraced will update the
* hash and reset here. If it is already converted, skip it.
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
*/
if (ftrace_ip_converted(ip))
goto out_unlock;
node = ftrace_alloc_dyn_node(ip);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (!node)
goto out_unlock;
node->ip = ip;
ftrace_add_hash(node, key);
ftraced_trigger = 1;
out_unlock:
spin_unlock_irqrestore(&ftrace_shutdown_lock, flags);
out:
per_cpu(ftrace_shutdown_disable_cpu, cpu)--;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
/* prevent recursion with scheduler */
if (resched)
preempt_enable_no_resched_notrace();
else
preempt_enable_notrace();
}
#define FTRACE_ADDR ((long)(ftrace_caller))
#define MCOUNT_ADDR ((long)(mcount))
static void
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
__ftrace_replace_code(struct dyn_ftrace *rec,
unsigned char *old, unsigned char *new, int enable)
{
unsigned long ip;
int failed;
ip = rec->ip;
if (ftrace_filtered && enable) {
unsigned long fl;
/*
* If filtering is on:
*
* If this record is set to be filtered and
* is enabled then do nothing.
*
* If this record is set to be filtered and
* it is not enabled, enable it.
*
* If this record is not set to be filtered
* and it is not enabled do nothing.
*
* If this record is not set to be filtered and
* it is enabled, disable it.
*/
fl = rec->flags & (FTRACE_FL_FILTER | FTRACE_FL_ENABLED);
if ((fl == (FTRACE_FL_FILTER | FTRACE_FL_ENABLED)) ||
(fl == 0))
return;
/*
* If it is enabled disable it,
* otherwise enable it!
*/
if (fl == FTRACE_FL_ENABLED) {
/* swap new and old */
new = old;
old = ftrace_call_replace(ip, FTRACE_ADDR);
rec->flags &= ~FTRACE_FL_ENABLED;
} else {
new = ftrace_call_replace(ip, FTRACE_ADDR);
rec->flags |= FTRACE_FL_ENABLED;
}
} else {
if (enable)
new = ftrace_call_replace(ip, FTRACE_ADDR);
else
old = ftrace_call_replace(ip, FTRACE_ADDR);
if (enable) {
if (rec->flags & FTRACE_FL_ENABLED)
return;
rec->flags |= FTRACE_FL_ENABLED;
} else {
if (!(rec->flags & FTRACE_FL_ENABLED))
return;
rec->flags &= ~FTRACE_FL_ENABLED;
}
}
failed = ftrace_modify_code(ip, old, new);
if (failed) {
unsigned long key;
/* It is possible that the function hasn't been converted yet */
key = hash_long(ip, FTRACE_HASHBITS);
if (!ftrace_ip_in_hash(ip, key)) {
rec->flags |= FTRACE_FL_FAILED;
ftrace_free_rec(rec);
}
}
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
}
static void ftrace_replace_code(int enable)
{
unsigned char *new = NULL, *old = NULL;
struct dyn_ftrace *rec;
struct ftrace_page *pg;
int i;
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
if (enable)
old = ftrace_nop_replace();
else
new = ftrace_nop_replace();
for (pg = ftrace_pages_start; pg; pg = pg->next) {
for (i = 0; i < pg->index; i++) {
rec = &pg->records[i];
/* don't modify code that has already faulted */
if (rec->flags & FTRACE_FL_FAILED)
continue;
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
__ftrace_replace_code(rec, old, new, enable);
}
}
}
static void ftrace_shutdown_replenish(void)
{
if (ftrace_pages->next)
return;
/* allocate another page */
ftrace_pages->next = (void *)get_zeroed_page(GFP_KERNEL);
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
static void
ftrace_code_disable(struct dyn_ftrace *rec)
{
unsigned long ip;
unsigned char *nop, *call;
int failed;
ip = rec->ip;
nop = ftrace_nop_replace();
call = ftrace_call_replace(ip, MCOUNT_ADDR);
failed = ftrace_modify_code(ip, call, nop);
if (failed) {
rec->flags |= FTRACE_FL_FAILED;
ftrace_free_rec(rec);
}
}
static int __ftrace_modify_code(void *data)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
unsigned long addr;
int *command = data;
if (*command & FTRACE_ENABLE_CALLS)
ftrace_replace_code(1);
else if (*command & FTRACE_DISABLE_CALLS)
ftrace_replace_code(0);
if (*command & FTRACE_UPDATE_TRACE_FUNC)
ftrace_update_ftrace_func(ftrace_trace_function);
if (*command & FTRACE_ENABLE_MCOUNT) {
addr = (unsigned long)ftrace_record_ip;
ftrace_mcount_set(&addr);
} else if (*command & FTRACE_DISABLE_MCOUNT) {
addr = (unsigned long)ftrace_stub;
ftrace_mcount_set(&addr);
}
return 0;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
}
static void ftrace_run_update_code(int command)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
stop_machine_run(__ftrace_modify_code, &command, NR_CPUS);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
}
static ftrace_func_t saved_ftrace_func;
static void ftrace_startup(void)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
int command = 0;
if (unlikely(ftrace_disabled))
return;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
mutex_lock(&ftraced_lock);
ftraced_suspend++;
if (ftraced_suspend == 1)
command |= FTRACE_ENABLE_CALLS;
if (saved_ftrace_func != ftrace_trace_function) {
saved_ftrace_func = ftrace_trace_function;
command |= FTRACE_UPDATE_TRACE_FUNC;
}
if (!command || !ftrace_enabled)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
goto out;
ftrace_run_update_code(command);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
out:
mutex_unlock(&ftraced_lock);
}
static void ftrace_shutdown(void)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
int command = 0;
if (unlikely(ftrace_disabled))
return;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
mutex_lock(&ftraced_lock);
ftraced_suspend--;
if (!ftraced_suspend)
command |= FTRACE_DISABLE_CALLS;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (saved_ftrace_func != ftrace_trace_function) {
saved_ftrace_func = ftrace_trace_function;
command |= FTRACE_UPDATE_TRACE_FUNC;
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (!command || !ftrace_enabled)
goto out;
ftrace_run_update_code(command);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
out:
mutex_unlock(&ftraced_lock);
}
static void ftrace_startup_sysctl(void)
{
int command = FTRACE_ENABLE_MCOUNT;
if (unlikely(ftrace_disabled))
return;
mutex_lock(&ftraced_lock);
/* Force update next time */
saved_ftrace_func = NULL;
/* ftraced_suspend is true if we want ftrace running */
if (ftraced_suspend)
command |= FTRACE_ENABLE_CALLS;
ftrace_run_update_code(command);
mutex_unlock(&ftraced_lock);
}
static void ftrace_shutdown_sysctl(void)
{
int command = FTRACE_DISABLE_MCOUNT;
if (unlikely(ftrace_disabled))
return;
mutex_lock(&ftraced_lock);
/* ftraced_suspend is true if ftrace is running */
if (ftraced_suspend)
command |= FTRACE_DISABLE_CALLS;
ftrace_run_update_code(command);
mutex_unlock(&ftraced_lock);
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
static cycle_t ftrace_update_time;
static unsigned long ftrace_update_cnt;
unsigned long ftrace_update_tot_cnt;
static int __ftrace_update_code(void *ignore)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
struct dyn_ftrace *p;
struct hlist_head head;
struct hlist_node *t;
int save_ftrace_enabled;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
cycle_t start, stop;
int i;
/* Don't be recording funcs now */
save_ftrace_enabled = ftrace_enabled;
ftrace_enabled = 0;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
start = ftrace_now(raw_smp_processor_id());
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_update_cnt = 0;
/* No locks needed, the machine is stopped! */
for (i = 0; i < FTRACE_HASHSIZE; i++) {
if (hlist_empty(&ftrace_hash[i]))
continue;
head = ftrace_hash[i];
INIT_HLIST_HEAD(&ftrace_hash[i]);
/* all CPUS are stopped, we are safe to modify code */
hlist_for_each_entry(p, t, &head, node) {
ftrace_code_disable(p);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_update_cnt++;
}
}
stop = ftrace_now(raw_smp_processor_id());
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_update_time = stop - start;
ftrace_update_tot_cnt += ftrace_update_cnt;
ftrace_enabled = save_ftrace_enabled;
return 0;
}
static void ftrace_update_code(void)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
if (unlikely(ftrace_disabled))
return;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
stop_machine_run(__ftrace_update_code, NULL, NR_CPUS);
}
static int ftraced(void *ignore)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
unsigned long usecs;
while (!kthread_should_stop()) {
set_current_state(TASK_INTERRUPTIBLE);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
/* check once a second */
schedule_timeout(HZ);
if (unlikely(ftrace_disabled))
continue;
mutex_lock(&ftrace_sysctl_lock);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
mutex_lock(&ftraced_lock);
if (ftrace_enabled && ftraced_trigger && !ftraced_suspend) {
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_record_suspend++;
ftrace_update_code();
usecs = nsecs_to_usecs(ftrace_update_time);
if (ftrace_update_tot_cnt > 100000) {
ftrace_update_tot_cnt = 0;
pr_info("hm, dftrace overflow: %lu change%s"
" (%lu total) in %lu usec%s\n",
ftrace_update_cnt,
ftrace_update_cnt != 1 ? "s" : "",
ftrace_update_tot_cnt,
usecs, usecs != 1 ? "s" : "");
ftrace_disabled = 1;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
WARN_ON_ONCE(1);
}
ftraced_trigger = 0;
ftrace_record_suspend--;
}
ftraced_iteration_counter++;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
mutex_unlock(&ftraced_lock);
mutex_unlock(&ftrace_sysctl_lock);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
wake_up_interruptible(&ftraced_waiters);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ftrace_shutdown_replenish();
}
__set_current_state(TASK_RUNNING);
return 0;
}
static int __init ftrace_dyn_table_alloc(void)
{
struct ftrace_page *pg;
int cnt;
int i;
/* allocate a few pages */
ftrace_pages_start = (void *)get_zeroed_page(GFP_KERNEL);
if (!ftrace_pages_start)
return -1;
/*
* Allocate a few more pages.
*
* TODO: have some parser search vmlinux before
* final linking to find all calls to ftrace.
* Then we can:
* a) know how many pages to allocate.
* and/or
* b) set up the table then.
*
* The dynamic code is still necessary for
* modules.
*/
pg = ftrace_pages = ftrace_pages_start;
cnt = NR_TO_INIT / ENTRIES_PER_PAGE;
for (i = 0; i < cnt; i++) {
pg->next = (void *)get_zeroed_page(GFP_KERNEL);
/* If we fail, we'll try later anyway */
if (!pg->next)
break;
pg = pg->next;
}
return 0;
}
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
enum {
FTRACE_ITER_FILTER = (1 << 0),
FTRACE_ITER_CONT = (1 << 1),
};
#define FTRACE_BUFF_MAX (KSYM_SYMBOL_LEN+4) /* room for wildcards */
struct ftrace_iterator {
loff_t pos;
struct ftrace_page *pg;
unsigned idx;
unsigned flags;
unsigned char buffer[FTRACE_BUFF_MAX+1];
unsigned buffer_idx;
unsigned filtered;
};
static void *
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
t_next(struct seq_file *m, void *v, loff_t *pos)
{
struct ftrace_iterator *iter = m->private;
struct dyn_ftrace *rec = NULL;
(*pos)++;
retry:
if (iter->idx >= iter->pg->index) {
if (iter->pg->next) {
iter->pg = iter->pg->next;
iter->idx = 0;
goto retry;
}
} else {
rec = &iter->pg->records[iter->idx++];
if ((rec->flags & FTRACE_FL_FAILED) ||
((iter->flags & FTRACE_ITER_FILTER) &&
!(rec->flags & FTRACE_FL_FILTER))) {
rec = NULL;
goto retry;
}
}
iter->pos = *pos;
return rec;
}
static void *t_start(struct seq_file *m, loff_t *pos)
{
struct ftrace_iterator *iter = m->private;
void *p = NULL;
loff_t l = -1;
if (*pos != iter->pos) {
for (p = t_next(m, p, &l); p && l < *pos; p = t_next(m, p, &l))
;
} else {
l = *pos;
p = t_next(m, p, &l);
}
return p;
}
static void t_stop(struct seq_file *m, void *p)
{
}
static int t_show(struct seq_file *m, void *v)
{
struct dyn_ftrace *rec = v;
char str[KSYM_SYMBOL_LEN];
if (!rec)
return 0;
kallsyms_lookup(rec->ip, NULL, NULL, NULL, str);
seq_printf(m, "%s\n", str);
return 0;
}
static struct seq_operations show_ftrace_seq_ops = {
.start = t_start,
.next = t_next,
.stop = t_stop,
.show = t_show,
};
static int
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_avail_open(struct inode *inode, struct file *file)
{
struct ftrace_iterator *iter;
int ret;
if (unlikely(ftrace_disabled))
return -ENODEV;
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
iter = kzalloc(sizeof(*iter), GFP_KERNEL);
if (!iter)
return -ENOMEM;
iter->pg = ftrace_pages_start;
iter->pos = -1;
ret = seq_open(file, &show_ftrace_seq_ops);
if (!ret) {
struct seq_file *m = file->private_data;
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
m->private = iter;
} else {
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
kfree(iter);
}
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
return ret;
}
int ftrace_avail_release(struct inode *inode, struct file *file)
{
struct seq_file *m = (struct seq_file *)file->private_data;
struct ftrace_iterator *iter = m->private;
seq_release(inode, file);
kfree(iter);
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
return 0;
}
static void ftrace_filter_reset(void)
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
{
struct ftrace_page *pg;
struct dyn_ftrace *rec;
unsigned i;
/* keep kstop machine from running */
preempt_disable();
ftrace_filtered = 0;
pg = ftrace_pages_start;
while (pg) {
for (i = 0; i < pg->index; i++) {
rec = &pg->records[i];
if (rec->flags & FTRACE_FL_FAILED)
continue;
rec->flags &= ~FTRACE_FL_FILTER;
}
pg = pg->next;
}
preempt_enable();
}
static int
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_filter_open(struct inode *inode, struct file *file)
{
struct ftrace_iterator *iter;
int ret = 0;
if (unlikely(ftrace_disabled))
return -ENODEV;
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
iter = kzalloc(sizeof(*iter), GFP_KERNEL);
if (!iter)
return -ENOMEM;
mutex_lock(&ftrace_filter_lock);
if ((file->f_mode & FMODE_WRITE) &&
!(file->f_flags & O_APPEND))
ftrace_filter_reset();
if (file->f_mode & FMODE_READ) {
iter->pg = ftrace_pages_start;
iter->pos = -1;
iter->flags = FTRACE_ITER_FILTER;
ret = seq_open(file, &show_ftrace_seq_ops);
if (!ret) {
struct seq_file *m = file->private_data;
m->private = iter;
} else
kfree(iter);
} else
file->private_data = iter;
mutex_unlock(&ftrace_filter_lock);
return ret;
}
static ssize_t
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_filter_read(struct file *file, char __user *ubuf,
size_t cnt, loff_t *ppos)
{
if (file->f_mode & FMODE_READ)
return seq_read(file, ubuf, cnt, ppos);
else
return -EPERM;
}
static loff_t
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_filter_lseek(struct file *file, loff_t offset, int origin)
{
loff_t ret;
if (file->f_mode & FMODE_READ)
ret = seq_lseek(file, offset, origin);
else
file->f_pos = ret = 1;
return ret;
}
enum {
MATCH_FULL,
MATCH_FRONT_ONLY,
MATCH_MIDDLE_ONLY,
MATCH_END_ONLY,
};
static void
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_match(unsigned char *buff, int len)
{
char str[KSYM_SYMBOL_LEN];
char *search = NULL;
struct ftrace_page *pg;
struct dyn_ftrace *rec;
int type = MATCH_FULL;
unsigned i, match = 0, search_len = 0;
for (i = 0; i < len; i++) {
if (buff[i] == '*') {
if (!i) {
search = buff + i + 1;
type = MATCH_END_ONLY;
search_len = len - (i + 1);
} else {
if (type == MATCH_END_ONLY) {
type = MATCH_MIDDLE_ONLY;
} else {
match = i;
type = MATCH_FRONT_ONLY;
}
buff[i] = 0;
break;
}
}
}
/* keep kstop machine from running */
preempt_disable();
ftrace_filtered = 1;
pg = ftrace_pages_start;
while (pg) {
for (i = 0; i < pg->index; i++) {
int matched = 0;
char *ptr;
rec = &pg->records[i];
if (rec->flags & FTRACE_FL_FAILED)
continue;
kallsyms_lookup(rec->ip, NULL, NULL, NULL, str);
switch (type) {
case MATCH_FULL:
if (strcmp(str, buff) == 0)
matched = 1;
break;
case MATCH_FRONT_ONLY:
if (memcmp(str, buff, match) == 0)
matched = 1;
break;
case MATCH_MIDDLE_ONLY:
if (strstr(str, search))
matched = 1;
break;
case MATCH_END_ONLY:
ptr = strstr(str, search);
if (ptr && (ptr[search_len] == 0))
matched = 1;
break;
}
if (matched)
rec->flags |= FTRACE_FL_FILTER;
}
pg = pg->next;
}
preempt_enable();
}
static ssize_t
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_filter_write(struct file *file, const char __user *ubuf,
size_t cnt, loff_t *ppos)
{
struct ftrace_iterator *iter;
char ch;
size_t read = 0;
ssize_t ret;
if (!cnt || cnt < 0)
return 0;
mutex_lock(&ftrace_filter_lock);
if (file->f_mode & FMODE_READ) {
struct seq_file *m = file->private_data;
iter = m->private;
} else
iter = file->private_data;
if (!*ppos) {
iter->flags &= ~FTRACE_ITER_CONT;
iter->buffer_idx = 0;
}
ret = get_user(ch, ubuf++);
if (ret)
goto out;
read++;
cnt--;
if (!(iter->flags & ~FTRACE_ITER_CONT)) {
/* skip white space */
while (cnt && isspace(ch)) {
ret = get_user(ch, ubuf++);
if (ret)
goto out;
read++;
cnt--;
}
if (isspace(ch)) {
file->f_pos += read;
ret = read;
goto out;
}
iter->buffer_idx = 0;
}
while (cnt && !isspace(ch)) {
if (iter->buffer_idx < FTRACE_BUFF_MAX)
iter->buffer[iter->buffer_idx++] = ch;
else {
ret = -EINVAL;
goto out;
}
ret = get_user(ch, ubuf++);
if (ret)
goto out;
read++;
cnt--;
}
if (isspace(ch)) {
iter->filtered++;
iter->buffer[iter->buffer_idx] = 0;
ftrace_match(iter->buffer, iter->buffer_idx);
iter->buffer_idx = 0;
} else
iter->flags |= FTRACE_ITER_CONT;
file->f_pos += read;
ret = read;
out:
mutex_unlock(&ftrace_filter_lock);
return ret;
}
/**
* ftrace_set_filter - set a function to filter on in ftrace
* @buf - the string that holds the function filter text.
* @len - the length of the string.
* @reset - non zero to reset all filters before applying this filter.
*
* Filters denote which functions should be enabled when tracing is enabled.
* If @buf is NULL and reset is set, all functions will be enabled for tracing.
*/
void ftrace_set_filter(unsigned char *buf, int len, int reset)
{
if (unlikely(ftrace_disabled))
return;
mutex_lock(&ftrace_filter_lock);
if (reset)
ftrace_filter_reset();
if (buf)
ftrace_match(buf, len);
mutex_unlock(&ftrace_filter_lock);
}
static int
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ftrace_filter_release(struct inode *inode, struct file *file)
{
struct seq_file *m = (struct seq_file *)file->private_data;
struct ftrace_iterator *iter;
mutex_lock(&ftrace_filter_lock);
if (file->f_mode & FMODE_READ) {
iter = m->private;
seq_release(inode, file);
} else
iter = file->private_data;
if (iter->buffer_idx) {
iter->filtered++;
iter->buffer[iter->buffer_idx] = 0;
ftrace_match(iter->buffer, iter->buffer_idx);
}
mutex_lock(&ftrace_sysctl_lock);
mutex_lock(&ftraced_lock);
if (iter->filtered && ftraced_suspend && ftrace_enabled)
ftrace_run_update_code(FTRACE_ENABLE_CALLS);
mutex_unlock(&ftraced_lock);
mutex_unlock(&ftrace_sysctl_lock);
kfree(iter);
mutex_unlock(&ftrace_filter_lock);
return 0;
}
static struct file_operations ftrace_avail_fops = {
.open = ftrace_avail_open,
.read = seq_read,
.llseek = seq_lseek,
.release = ftrace_avail_release,
};
static struct file_operations ftrace_filter_fops = {
.open = ftrace_filter_open,
.read = ftrace_filter_read,
.write = ftrace_filter_write,
.llseek = ftrace_filter_lseek,
.release = ftrace_filter_release,
};
/**
* ftrace_force_update - force an update to all recording ftrace functions
*
* The ftrace dynamic update daemon only wakes up once a second.
* There may be cases where an update needs to be done immediately
* for tests or internal kernel tracing to begin. This function
* wakes the daemon to do an update and will not return until the
* update is complete.
*/
int ftrace_force_update(void)
{
unsigned long last_counter;
DECLARE_WAITQUEUE(wait, current);
int ret = 0;
if (unlikely(ftrace_disabled))
return -ENODEV;
mutex_lock(&ftraced_lock);
last_counter = ftraced_iteration_counter;
set_current_state(TASK_INTERRUPTIBLE);
add_wait_queue(&ftraced_waiters, &wait);
if (unlikely(!ftraced_task)) {
ret = -ENODEV;
goto out;
}
do {
mutex_unlock(&ftraced_lock);
wake_up_process(ftraced_task);
schedule();
mutex_lock(&ftraced_lock);
if (signal_pending(current)) {
ret = -EINTR;
break;
}
set_current_state(TASK_INTERRUPTIBLE);
} while (last_counter == ftraced_iteration_counter);
out:
mutex_unlock(&ftraced_lock);
remove_wait_queue(&ftraced_waiters, &wait);
set_current_state(TASK_RUNNING);
return ret;
}
static void ftrace_force_shutdown(void)
{
struct task_struct *task;
int command = FTRACE_DISABLE_CALLS | FTRACE_UPDATE_TRACE_FUNC;
mutex_lock(&ftraced_lock);
task = ftraced_task;
ftraced_task = NULL;
ftraced_suspend = -1;
ftrace_run_update_code(command);
mutex_unlock(&ftraced_lock);
if (task)
kthread_stop(task);
}
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
static __init int ftrace_init_debugfs(void)
{
struct dentry *d_tracer;
struct dentry *entry;
d_tracer = tracing_init_dentry();
entry = debugfs_create_file("available_filter_functions", 0444,
d_tracer, NULL, &ftrace_avail_fops);
if (!entry)
pr_warning("Could not create debugfs "
"'available_filter_functions' entry\n");
entry = debugfs_create_file("set_ftrace_filter", 0644, d_tracer,
NULL, &ftrace_filter_fops);
if (!entry)
pr_warning("Could not create debugfs "
"'set_ftrace_filter' entry\n");
return 0;
}
fs_initcall(ftrace_init_debugfs);
static int __init ftrace_dynamic_init(void)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
{
struct task_struct *p;
unsigned long addr;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
int ret;
addr = (unsigned long)ftrace_record_ip;
stop_machine_run(ftrace_dyn_arch_init, &addr, NR_CPUS);
/* ftrace_dyn_arch_init places the return code in addr */
if (addr) {
ret = (int)addr;
goto failed;
}
ret = ftrace_dyn_table_alloc();
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
if (ret)
goto failed;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
p = kthread_run(ftraced, NULL, "ftraced");
if (IS_ERR(p)) {
ret = -1;
goto failed;
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
last_ftrace_enabled = ftrace_enabled = 1;
ftraced_task = p;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
return 0;
failed:
ftrace_disabled = 1;
return ret;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
}
core_initcall(ftrace_dynamic_init);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#else
# define ftrace_startup() do { } while (0)
# define ftrace_shutdown() do { } while (0)
# define ftrace_startup_sysctl() do { } while (0)
# define ftrace_shutdown_sysctl() do { } while (0)
# define ftrace_force_shutdown() do { } while (0)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
#endif /* CONFIG_DYNAMIC_FTRACE */
/**
* ftrace_kill - totally shutdown ftrace
*
* This is a safety measure. If something was detected that seems
* wrong, calling this function will keep ftrace from doing
* any more modifications, and updates.
* used when something went wrong.
*/
void ftrace_kill(void)
{
mutex_lock(&ftrace_sysctl_lock);
ftrace_disabled = 1;
ftrace_enabled = 0;
clear_ftrace_function();
mutex_unlock(&ftrace_sysctl_lock);
/* Try to totally disable ftrace */
ftrace_force_shutdown();
}
/**
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
* register_ftrace_function - register a function for profiling
* @ops - ops structure that holds the function for profiling.
*
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
* Register a function to be called by all functions in the
* kernel.
*
* Note: @ops->func and all the functions it calls must be labeled
* with "notrace", otherwise it will go into a
* recursive loop.
*/
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
int register_ftrace_function(struct ftrace_ops *ops)
{
int ret;
if (unlikely(ftrace_disabled))
return -1;
mutex_lock(&ftrace_sysctl_lock);
ret = __register_ftrace_function(ops);
ftrace_startup();
mutex_unlock(&ftrace_sysctl_lock);
return ret;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
}
/**
* unregister_ftrace_function - unresgister a function for profiling.
* @ops - ops structure that holds the function to unregister
*
* Unregister a function that was added to be called by ftrace profiling.
*/
int unregister_ftrace_function(struct ftrace_ops *ops)
{
int ret;
mutex_lock(&ftrace_sysctl_lock);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
ret = __unregister_ftrace_function(ops);
ftrace_shutdown();
mutex_unlock(&ftrace_sysctl_lock);
return ret;
}
int
ftrace_enable_sysctl(struct ctl_table *table, int write,
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
struct file *file, void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
if (unlikely(ftrace_disabled))
return -ENODEV;
mutex_lock(&ftrace_sysctl_lock);
ftrace: add filter select functions to trace This patch adds two files to the debugfs system: /debugfs/tracing/available_filter_functions and /debugfs/tracing/set_ftrace_filter The available_filter_functions lists all functions that has been recorded by the ftraced that has called the ftrace_record_ip function. This is to allow users to see what functions have been converted to nops and can be enabled for tracing. To enable functions, simply echo the names (whitespace delimited) into set_ftrace_filter. Simple wildcards are also allowed. echo 'scheduler' > /debugfs/tracing/set_ftrace_filter Will have only the scheduler be activated when tracing is enabled. echo 'sched_*' > /debugfs/tracing/set_ftrace_filter Will have only the functions starting with 'sched_' be activated. echo '*lock' > /debugfs/tracing/set_ftrace_filter Will have only functions ending with 'lock' be activated. echo '*lock*' > /debugfs/tracing/set_ftrace_filter Will have only functions with 'lock' in its name be activated. Note: 'sched*lock' will not work. The only wildcards that are allowed is an asterisk and the beginning and or end of the string passed in. Multiple names can be passed in with whitespace delimited: echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter is also the same as: echo 'scheduler' > /debugfs/tracing/set_ftrace_filter echo '*lock' >> /debugfs/tracing/set_ftrace_filter echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter Appending does just that. It appends to the list. To disable all filters simply echo an empty line in: echo > /debugfs/tracing/set_ftrace_filter Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:43 +04:00
ret = proc_dointvec(table, write, file, buffer, lenp, ppos);
if (ret || !write || (last_ftrace_enabled == ftrace_enabled))
goto out;
last_ftrace_enabled = ftrace_enabled;
if (ftrace_enabled) {
ftrace_startup_sysctl();
/* we are starting ftrace again */
if (ftrace_list != &ftrace_list_end) {
if (ftrace_list->next == &ftrace_list_end)
ftrace_trace_function = ftrace_list->func;
else
ftrace_trace_function = ftrace_list_func;
}
} else {
/* stopping ftrace calls (just send to ftrace_stub) */
ftrace_trace_function = ftrace_stub;
ftrace_shutdown_sysctl();
}
out:
mutex_unlock(&ftrace_sysctl_lock);
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 23:20:42 +04:00
return ret;
}