WSL2-Linux-Kernel/drivers/regulator/mc13xxx-regulator-core.c

225 строки
6.2 KiB
C
Исходник Обычный вид История

/*
* Regulator Driver for Freescale MC13xxx PMIC
*
* Copyright 2010 Yong Shen <yong.shen@linaro.org>
*
* Based on mc13783 regulator driver :
* Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
* Copyright 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Regs infos taken from mc13xxx drivers from freescale and mc13xxx.pdf file
* from freescale
*/
#include <linux/mfd/mc13xxx.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/of_regulator.h>
#include <linux/platform_device.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/err.h>
#include <linux/module.h>
#include <linux/of.h>
#include "mc13xxx.h"
static int mc13xxx_regulator_enable(struct regulator_dev *rdev)
{
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
struct mc13xxx_regulator *mc13xxx_regulators = priv->mc13xxx_regulators;
int id = rdev_get_id(rdev);
dev_dbg(rdev_get_dev(rdev), "%s id: %d\n", __func__, id);
return mc13xxx_reg_rmw(priv->mc13xxx, mc13xxx_regulators[id].reg,
mc13xxx_regulators[id].enable_bit,
mc13xxx_regulators[id].enable_bit);
}
static int mc13xxx_regulator_disable(struct regulator_dev *rdev)
{
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
struct mc13xxx_regulator *mc13xxx_regulators = priv->mc13xxx_regulators;
int id = rdev_get_id(rdev);
dev_dbg(rdev_get_dev(rdev), "%s id: %d\n", __func__, id);
return mc13xxx_reg_rmw(priv->mc13xxx, mc13xxx_regulators[id].reg,
mc13xxx_regulators[id].enable_bit, 0);
}
static int mc13xxx_regulator_is_enabled(struct regulator_dev *rdev)
{
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
struct mc13xxx_regulator *mc13xxx_regulators = priv->mc13xxx_regulators;
int ret, id = rdev_get_id(rdev);
unsigned int val;
ret = mc13xxx_reg_read(priv->mc13xxx, mc13xxx_regulators[id].reg, &val);
if (ret)
return ret;
return (val & mc13xxx_regulators[id].enable_bit) != 0;
}
static int mc13xxx_regulator_set_voltage_sel(struct regulator_dev *rdev,
unsigned selector)
{
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
struct mc13xxx_regulator *mc13xxx_regulators = priv->mc13xxx_regulators;
int id = rdev_get_id(rdev);
return mc13xxx_reg_rmw(priv->mc13xxx, mc13xxx_regulators[id].vsel_reg,
mc13xxx_regulators[id].vsel_mask,
selector << mc13xxx_regulators[id].vsel_shift);
}
static int mc13xxx_regulator_get_voltage(struct regulator_dev *rdev)
{
struct mc13xxx_regulator_priv *priv = rdev_get_drvdata(rdev);
struct mc13xxx_regulator *mc13xxx_regulators = priv->mc13xxx_regulators;
int ret, id = rdev_get_id(rdev);
unsigned int val;
dev_dbg(rdev_get_dev(rdev), "%s id: %d\n", __func__, id);
ret = mc13xxx_reg_read(priv->mc13xxx,
mc13xxx_regulators[id].vsel_reg, &val);
if (ret)
return ret;
val = (val & mc13xxx_regulators[id].vsel_mask)
>> mc13xxx_regulators[id].vsel_shift;
dev_dbg(rdev_get_dev(rdev), "%s id: %d val: %d\n", __func__, id, val);
BUG_ON(val >= mc13xxx_regulators[id].desc.n_voltages);
return rdev->desc->volt_table[val];
}
struct regulator_ops mc13xxx_regulator_ops = {
.enable = mc13xxx_regulator_enable,
.disable = mc13xxx_regulator_disable,
.is_enabled = mc13xxx_regulator_is_enabled,
.list_voltage = regulator_list_voltage_table,
.set_voltage_sel = mc13xxx_regulator_set_voltage_sel,
.get_voltage = mc13xxx_regulator_get_voltage,
};
EXPORT_SYMBOL_GPL(mc13xxx_regulator_ops);
int mc13xxx_fixed_regulator_set_voltage(struct regulator_dev *rdev, int min_uV,
int max_uV, unsigned *selector)
{
int id = rdev_get_id(rdev);
dev_dbg(rdev_get_dev(rdev), "%s id: %d min_uV: %d max_uV: %d\n",
__func__, id, min_uV, max_uV);
if (min_uV <= rdev->desc->volt_table[0] &&
rdev->desc->volt_table[0] <= max_uV) {
*selector = 0;
return 0;
} else {
return -EINVAL;
}
}
EXPORT_SYMBOL_GPL(mc13xxx_fixed_regulator_set_voltage);
struct regulator_ops mc13xxx_fixed_regulator_ops = {
.enable = mc13xxx_regulator_enable,
.disable = mc13xxx_regulator_disable,
.is_enabled = mc13xxx_regulator_is_enabled,
.list_voltage = regulator_list_voltage_table,
.set_voltage = mc13xxx_fixed_regulator_set_voltage,
};
EXPORT_SYMBOL_GPL(mc13xxx_fixed_regulator_ops);
#ifdef CONFIG_OF
int mc13xxx_get_num_regulators_dt(struct platform_device *pdev)
{
struct device_node *parent;
int num;
if (!pdev->dev.parent->of_node)
return -ENODEV;
parent = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
if (!parent)
return -ENODEV;
num = of_get_child_count(parent);
of_node_put(parent);
return num;
}
EXPORT_SYMBOL_GPL(mc13xxx_get_num_regulators_dt);
struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
struct platform_device *pdev, struct mc13xxx_regulator *regulators,
int num_regulators)
{
struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
struct mc13xxx_regulator_init_data *data, *p;
struct device_node *parent, *child;
regulator: mc13892: sanity check num_regulators parsed vs. registered Imagine a situation where a device tree has a few regulators in an appropriate node: regulators { sw1 { .. }; vvideo { .. }; : vfake { .. }; vtypo { .. }; }; In the above example, the node name "vfake" is an attempt to match a regulator name inside the driver which just so happens to not exist. The node name "vtypo" represents an accidental typographical error in a regulator name which may have been introduced to a device tree. In these cases, the number of regulators the mc13892 driver thinks it has does not match the number of regulators it parsed and registered. Since it will go over this array based on this number, it will actually re-register regulator "0" (which happens to be SW1) over and over again until it reaches the number, resulting in messages on the kernel log such as these: SW1: at 1100 mV VVIDEO: at 2775mV : SW1: at 1100 mV SW1: at 1100 mV .. up to that number of "mismatched" regulators. Nobody using DT can/will consume these regulators, so it should not be possible for it to cause any real regulator problems or driver breakages, but it is an easy thing to miss in a kernel log and is an immediate indication of a problem with the device tree authoring. This patch effectively sanity checks the number of counted children of the regulators node vs. the number that actually matched driver names, and sets the appropriate num_regulators value. It also gives a little warning for device tree authors that they MAY have screwed something up, such that this patch does not hide the device tree authoring problem. Signed-off-by: Matt Sealey <matt@genesi-usa.com> Tested-by: Steev Klimaszewski <steev@genesi-usa.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21 22:25:45 +04:00
int i, parsed = 0;
if (!pdev->dev.parent->of_node)
return NULL;
parent = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
if (!parent)
return NULL;
data = devm_kzalloc(&pdev->dev, sizeof(*data) * priv->num_regulators,
GFP_KERNEL);
if (!data) {
of_node_put(parent);
return NULL;
}
p = data;
for_each_child_of_node(parent, child) {
int found = 0;
for (i = 0; i < num_regulators; i++) {
if (!regulators[i].desc.name)
continue;
if (!of_node_cmp(child->name,
regulators[i].desc.name)) {
p->id = i;
p->init_data = of_get_regulator_init_data(
&pdev->dev, child,
&regulators[i].desc);
p->node = child;
p++;
regulator: mc13892: sanity check num_regulators parsed vs. registered Imagine a situation where a device tree has a few regulators in an appropriate node: regulators { sw1 { .. }; vvideo { .. }; : vfake { .. }; vtypo { .. }; }; In the above example, the node name "vfake" is an attempt to match a regulator name inside the driver which just so happens to not exist. The node name "vtypo" represents an accidental typographical error in a regulator name which may have been introduced to a device tree. In these cases, the number of regulators the mc13892 driver thinks it has does not match the number of regulators it parsed and registered. Since it will go over this array based on this number, it will actually re-register regulator "0" (which happens to be SW1) over and over again until it reaches the number, resulting in messages on the kernel log such as these: SW1: at 1100 mV VVIDEO: at 2775mV : SW1: at 1100 mV SW1: at 1100 mV .. up to that number of "mismatched" regulators. Nobody using DT can/will consume these regulators, so it should not be possible for it to cause any real regulator problems or driver breakages, but it is an easy thing to miss in a kernel log and is an immediate indication of a problem with the device tree authoring. This patch effectively sanity checks the number of counted children of the regulators node vs. the number that actually matched driver names, and sets the appropriate num_regulators value. It also gives a little warning for device tree authors that they MAY have screwed something up, such that this patch does not hide the device tree authoring problem. Signed-off-by: Matt Sealey <matt@genesi-usa.com> Tested-by: Steev Klimaszewski <steev@genesi-usa.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21 22:25:45 +04:00
parsed++;
found = 1;
break;
}
}
if (!found)
dev_warn(&pdev->dev,
"Unknown regulator: %s\n", child->name);
}
of_node_put(parent);
priv->num_regulators = parsed;
return data;
}
EXPORT_SYMBOL_GPL(mc13xxx_parse_regulators_dt);
#endif
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Yong Shen <yong.shen@linaro.org>");
MODULE_DESCRIPTION("Regulator Driver for Freescale MC13xxx PMIC");
MODULE_ALIAS("mc13xxx-regulator-core");