2008-11-24 22:53:35 +03:00
|
|
|
#
|
|
|
|
|
# USB OTG infrastructure may be needed for peripheral-only, host-only,
|
|
|
|
|
# or OTG-capable configurations when OTG transceivers or controllers
|
|
|
|
|
# are used.
|
|
|
|
|
#
|
|
|
|
|
|
|
|
|
|
comment "OTG and related infrastructure"
|
|
|
|
|
|
|
|
|
|
config USB_OTG_UTILS
|
|
|
|
|
bool
|
|
|
|
|
help
|
|
|
|
|
Select this to make sure the build includes objects from
|
|
|
|
|
the OTG infrastructure directory.
|
|
|
|
|
|
2009-01-25 04:55:57 +03:00
|
|
|
if USB || USB_GADGET
|
|
|
|
|
|
2008-11-24 23:00:01 +03:00
|
|
|
#
|
|
|
|
|
# USB Transceiver Drivers
|
|
|
|
|
#
|
|
|
|
|
config USB_GPIO_VBUS
|
|
|
|
|
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
|
|
|
|
depends on GENERIC_GPIO
|
|
|
|
|
select USB_OTG_UTILS
|
|
|
|
|
help
|
|
|
|
|
Provides simple GPIO VBUS sensing for controllers with an
|
|
|
|
|
internal transceiver via the otg_transceiver interface, and
|
|
|
|
|
optionally control of a D+ pullup GPIO as well as a VBUS
|
|
|
|
|
current limit regulator.
|
|
|
|
|
|
2008-11-24 22:53:35 +03:00
|
|
|
config ISP1301_OMAP
|
|
|
|
|
tristate "Philips ISP1301 with OMAP OTG"
|
|
|
|
|
depends on I2C && ARCH_OMAP_OTG
|
|
|
|
|
select USB_OTG_UTILS
|
|
|
|
|
help
|
|
|
|
|
If you say yes here you get support for the Philips ISP1301
|
|
|
|
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
|
|
|
|
The ISP1301 is a full speed USB transceiver which is used in
|
|
|
|
|
products including H2, H3, and H4 development boards for Texas
|
|
|
|
|
Instruments OMAP processors.
|
|
|
|
|
|
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
|
|
|
will be called isp1301_omap.
|
|
|
|
|
|
2009-10-15 18:09:35 +04:00
|
|
|
config USB_ULPI
|
|
|
|
|
bool "Generic ULPI Transceiver Driver"
|
|
|
|
|
depends on ARM
|
2010-01-20 22:06:31 +03:00
|
|
|
select USB_OTG_UTILS
|
2009-10-15 18:09:35 +04:00
|
|
|
help
|
|
|
|
|
Enable this to support ULPI connected USB OTG transceivers which
|
|
|
|
|
are likely found on embedded boards.
|
|
|
|
|
|
|
|
|
|
The only chip currently supported is NXP's ISP1504
|
|
|
|
|
|
2008-12-18 23:25:44 +03:00
|
|
|
config TWL4030_USB
|
|
|
|
|
tristate "TWL4030 USB Transceiver Driver"
|
2009-02-20 15:02:31 +03:00
|
|
|
depends on TWL4030_CORE && REGULATOR_TWL4030
|
2008-12-18 23:25:44 +03:00
|
|
|
select USB_OTG_UTILS
|
|
|
|
|
help
|
|
|
|
|
Enable this to support the USB OTG transceiver on TWL4030
|
|
|
|
|
family chips (including the TWL5030 and TPS659x0 devices).
|
|
|
|
|
This transceiver supports high and full speed devices plus,
|
|
|
|
|
in host mode, low speed.
|
|
|
|
|
|
2009-02-06 15:02:35 +03:00
|
|
|
config NOP_USB_XCEIV
|
|
|
|
|
tristate "NOP USB Transceiver Driver"
|
|
|
|
|
select USB_OTG_UTILS
|
|
|
|
|
help
|
|
|
|
|
this driver is to be used by all the usb transceiver which are either
|
|
|
|
|
built-in with usb ip or which are autonomous and doesn't require any
|
|
|
|
|
phy programming such as ISP1x04 etc.
|
|
|
|
|
|
2008-11-24 22:53:35 +03:00
|
|
|
endif # USB || OTG
|
