WSL2-Linux-Kernel/drivers/nfc/st-nci/Makefile

#
# Makefile for ST_NCI NCI based NFC driver
#

st-nci-objs = ndlc.o core.o se.o vendor_cmds.o
obj-$(CONFIG_NFC_ST_NCI)     += st-nci.o

st-nci_i2c-objs = i2c.o
obj-$(CONFIG_NFC_ST_NCI_I2C) += st-nci_i2c.o

st-nci_spi-objs = spi.o
obj-$(CONFIG_NFC_ST_NCI_SPI) += st-nci_spi.o
nfc: st-nci: Rename st21nfcb to st-nci STMicroelectronics NFC NCI chips family is extending with the new ST21NFCC using the AMS AS39230 RF booster. The st21nfcb driver is relevant for this solution and might be with future products. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-06-09 23:26:05 +03:00			`#`
NFC: st-nci: Replace st21nfcb by st_nci in makefile Replace 1 missing st21nfcb by st_nci Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-10-26 00:54:50 +03:00			`# Makefile for ST_NCI NCI based NFC driver`
nfc: st-nci: Rename st21nfcb to st-nci STMicroelectronics NFC NCI chips family is extending with the new ST21NFCC using the AMS AS39230 RF booster. The st21nfcb driver is relevant for this solution and might be with future products. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-06-09 23:26:05 +03:00			`#`

NFC: st-nci: Add support for proprietary commands Add support for proprietary commands useful mainly for factory testings. Here is a list: - FACTORY_MODE: Allow to set the driver into a mode where no secure element are activated. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes command. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_DM_PUT_DATA: Allow to configure specific CLF registry like for example RF trimmings or low level drivers configurations (I2C, SPI, SWP). - HCI_DM_UPDATE_AID: Allow to configure an AID routing into the CLF routing table following RF technology, CLF mode or protocol. - HCI_DM_GET_INFO: Allow to retrieve CLF information. - HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as low level drivers configurations or RF trimmings. - HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF. A complete packet can be more than 8KB. - HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF configuration changes without CLF power off. - HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example the white list). - HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF technology. When using this command to anti-collision is done. - HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF connectivity. - HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied on the CLF antenna. A value between 0 and 0x0f is returned. 0 is maximum. - HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode. It is a specific CLF command as there is no GPIO for this. - HCI_DM_FWUPD_END: Allow to complete firmware update. - HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied on the CLF antenna to a reference value. - MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data received during a NCI_CORE_INIT_CMD. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-10-26 00:54:36 +03:00			`st-nci-objs = ndlc.o core.o se.o vendor_cmds.o`
nfc: st-nci: Rename st21nfcb to st-nci STMicroelectronics NFC NCI chips family is extending with the new ST21NFCC using the AMS AS39230 RF booster. The st21nfcb driver is relevant for this solution and might be with future products. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-06-09 23:26:05 +03:00			`obj-$(CONFIG_NFC_ST_NCI) += st-nci.o`

			`st-nci_i2c-objs = i2c.o`
			`obj-$(CONFIG_NFC_ST_NCI_I2C) += st-nci_i2c.o`
nfc: st-nci: Add spi phy support for st21nfcb st21nfcb does support another phy than i2c: spi. st21nfcc does not support spi as the spi ios are used by the AMS RF booster. st21nfcb is not following NCI NFC Forum recommendations for spi but rely on ST prioritary protocol ndlc as for i2c. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> 2015-08-14 23:33:37 +03:00
			`st-nci_spi-objs = spi.o`
			`obj-$(CONFIG_NFC_ST_NCI_SPI) += st-nci_spi.o`