WSL2-Linux-Kernel/drivers/net/dsa/realtek-smi-core.h

148 строки
4.3 KiB
C
Исходник Обычный вид История

net: dsa: realtek-smi: Add Realtek SMI driver This adds a driver core for the Realtek SMI chips and a subdriver for the RTL8366RB. I just added this chip simply because it is all I can test. The code is a massaged variant of the code that has been sitting out-of-tree in OpenWRT for years in the absence of a proper switch subsystem. This creates a DSA driver for it. I have tried to credit the original authors wherever possible. The main changes I've done from the OpenWRT code: - Added an IRQ chip inside the RTL8366RB switch to demux and handle the line state IRQs. - Distributed the phy handling out to the PHY driver. - Added some RTL8366RB code that was missing in the driver at the time, such as setting up "green ethernet" with a funny jam table and forcing MAC5 (the CPU port) into 1 GBit. - Select jam table and add the default jam table from the vendor driver, also for ASIC "version 0" if need be. - Do not store jam tables in the device tree, store them in the driver. - Pick in the "initvals" jam tables from OpenWRT's driver and make those get selected per compatible for the whole system. It's apparently about electrical settings for this system and whatnot, not really configuration from device tree. - Implemented LED control: beware of bugs because there are no LEDs on the device I am using! We do not implement custom DSA tags. This is explained in a comment in the driver as well: this "tagging protocol" is not simply a few extra bytes tagged on to the ethernet frame as DSA is used to. Instead, enabling the CPU tags will make the switch start talking Realtek RRCP internally. For example a simple ping will make this kind of packets appear inside the switch: 0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00 0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d 0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00 0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 As you can see a custom "8899" tagged packet using the protocol 0xa2. Norm RRCP appears to always have this protocol set to 0x01 according to OpenRRCP. You can also see that this is not a ping packet at all, instead the switch is starting to talk network management issues with the CPU port. So for now custom "tagging" is disabled. This was tested on the D-Link DIR-685 with initramfs and OpenWRT userspaces and works fine on all the LAN ports (lan0 .. lan3). The WAN port is yet not working. Cc: Antti Seppälä <a.seppala@gmail.com> Cc: Roman Yeryomin <roman@advem.lv> Cc: Colin Leitner <colin.leitner@googlemail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14 12:45:55 +03:00
/* SPDX-License-Identifier: GPL-2.0+ */
/* Realtek SMI interface driver defines
*
* Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
* Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
*/
#ifndef _REALTEK_SMI_H
#define _REALTEK_SMI_H
#include <linux/phy.h>
#include <linux/platform_device.h>
#include <linux/gpio/consumer.h>
#include <net/dsa.h>
struct realtek_smi_ops;
struct dentry;
struct inode;
struct file;
struct rtl8366_mib_counter {
unsigned int base;
unsigned int offset;
unsigned int length;
const char *name;
};
/**
* struct rtl8366_vlan_mc - Virtual LAN member configuration
*/
net: dsa: realtek-smi: Add Realtek SMI driver This adds a driver core for the Realtek SMI chips and a subdriver for the RTL8366RB. I just added this chip simply because it is all I can test. The code is a massaged variant of the code that has been sitting out-of-tree in OpenWRT for years in the absence of a proper switch subsystem. This creates a DSA driver for it. I have tried to credit the original authors wherever possible. The main changes I've done from the OpenWRT code: - Added an IRQ chip inside the RTL8366RB switch to demux and handle the line state IRQs. - Distributed the phy handling out to the PHY driver. - Added some RTL8366RB code that was missing in the driver at the time, such as setting up "green ethernet" with a funny jam table and forcing MAC5 (the CPU port) into 1 GBit. - Select jam table and add the default jam table from the vendor driver, also for ASIC "version 0" if need be. - Do not store jam tables in the device tree, store them in the driver. - Pick in the "initvals" jam tables from OpenWRT's driver and make those get selected per compatible for the whole system. It's apparently about electrical settings for this system and whatnot, not really configuration from device tree. - Implemented LED control: beware of bugs because there are no LEDs on the device I am using! We do not implement custom DSA tags. This is explained in a comment in the driver as well: this "tagging protocol" is not simply a few extra bytes tagged on to the ethernet frame as DSA is used to. Instead, enabling the CPU tags will make the switch start talking Realtek RRCP internally. For example a simple ping will make this kind of packets appear inside the switch: 0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00 0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d 0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00 0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 As you can see a custom "8899" tagged packet using the protocol 0xa2. Norm RRCP appears to always have this protocol set to 0x01 according to OpenRRCP. You can also see that this is not a ping packet at all, instead the switch is starting to talk network management issues with the CPU port. So for now custom "tagging" is disabled. This was tested on the D-Link DIR-685 with initramfs and OpenWRT userspaces and works fine on all the LAN ports (lan0 .. lan3). The WAN port is yet not working. Cc: Antti Seppälä <a.seppala@gmail.com> Cc: Roman Yeryomin <roman@advem.lv> Cc: Colin Leitner <colin.leitner@googlemail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14 12:45:55 +03:00
struct rtl8366_vlan_mc {
u16 vid;
u16 untag;
u16 member;
u8 fid;
u8 priority;
};
struct rtl8366_vlan_4k {
u16 vid;
u16 untag;
u16 member;
u8 fid;
};
struct realtek_smi {
struct device *dev;
struct gpio_desc *reset;
struct gpio_desc *mdc;
struct gpio_desc *mdio;
struct regmap *map;
struct mii_bus *slave_mii_bus;
unsigned int clk_delay;
u8 cmd_read;
u8 cmd_write;
spinlock_t lock; /* Locks around command writes */
struct dsa_switch *ds;
struct irq_domain *irqdomain;
bool leds_disabled;
unsigned int cpu_port;
unsigned int num_ports;
unsigned int num_vlan_mc;
unsigned int num_mib_counters;
struct rtl8366_mib_counter *mib_counters;
const struct realtek_smi_ops *ops;
int vlan_enabled;
int vlan4k_enabled;
char buf[4096];
void *chip_data; /* Per-chip extra variant data */
net: dsa: realtek-smi: Add Realtek SMI driver This adds a driver core for the Realtek SMI chips and a subdriver for the RTL8366RB. I just added this chip simply because it is all I can test. The code is a massaged variant of the code that has been sitting out-of-tree in OpenWRT for years in the absence of a proper switch subsystem. This creates a DSA driver for it. I have tried to credit the original authors wherever possible. The main changes I've done from the OpenWRT code: - Added an IRQ chip inside the RTL8366RB switch to demux and handle the line state IRQs. - Distributed the phy handling out to the PHY driver. - Added some RTL8366RB code that was missing in the driver at the time, such as setting up "green ethernet" with a funny jam table and forcing MAC5 (the CPU port) into 1 GBit. - Select jam table and add the default jam table from the vendor driver, also for ASIC "version 0" if need be. - Do not store jam tables in the device tree, store them in the driver. - Pick in the "initvals" jam tables from OpenWRT's driver and make those get selected per compatible for the whole system. It's apparently about electrical settings for this system and whatnot, not really configuration from device tree. - Implemented LED control: beware of bugs because there are no LEDs on the device I am using! We do not implement custom DSA tags. This is explained in a comment in the driver as well: this "tagging protocol" is not simply a few extra bytes tagged on to the ethernet frame as DSA is used to. Instead, enabling the CPU tags will make the switch start talking Realtek RRCP internally. For example a simple ping will make this kind of packets appear inside the switch: 0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00 0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d 0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00 0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 As you can see a custom "8899" tagged packet using the protocol 0xa2. Norm RRCP appears to always have this protocol set to 0x01 according to OpenRRCP. You can also see that this is not a ping packet at all, instead the switch is starting to talk network management issues with the CPU port. So for now custom "tagging" is disabled. This was tested on the D-Link DIR-685 with initramfs and OpenWRT userspaces and works fine on all the LAN ports (lan0 .. lan3). The WAN port is yet not working. Cc: Antti Seppälä <a.seppala@gmail.com> Cc: Roman Yeryomin <roman@advem.lv> Cc: Colin Leitner <colin.leitner@googlemail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14 12:45:55 +03:00
};
/**
* struct realtek_smi_ops - vtable for the per-SMI-chiptype operations
* @detect: detects the chiptype
*/
struct realtek_smi_ops {
int (*detect)(struct realtek_smi *smi);
int (*reset_chip)(struct realtek_smi *smi);
int (*setup)(struct realtek_smi *smi);
void (*cleanup)(struct realtek_smi *smi);
int (*get_mib_counter)(struct realtek_smi *smi,
int port,
struct rtl8366_mib_counter *mib,
u64 *mibvalue);
int (*get_vlan_mc)(struct realtek_smi *smi, u32 index,
struct rtl8366_vlan_mc *vlanmc);
int (*set_vlan_mc)(struct realtek_smi *smi, u32 index,
const struct rtl8366_vlan_mc *vlanmc);
int (*get_vlan_4k)(struct realtek_smi *smi, u32 vid,
struct rtl8366_vlan_4k *vlan4k);
int (*set_vlan_4k)(struct realtek_smi *smi,
const struct rtl8366_vlan_4k *vlan4k);
int (*get_mc_index)(struct realtek_smi *smi, int port, int *val);
int (*set_mc_index)(struct realtek_smi *smi, int port, int index);
bool (*is_vlan_valid)(struct realtek_smi *smi, unsigned int vlan);
int (*enable_vlan)(struct realtek_smi *smi, bool enable);
int (*enable_vlan4k)(struct realtek_smi *smi, bool enable);
int (*enable_port)(struct realtek_smi *smi, int port, bool enable);
int (*phy_read)(struct realtek_smi *smi, int phy, int regnum);
int (*phy_write)(struct realtek_smi *smi, int phy, int regnum,
u16 val);
};
struct realtek_smi_variant {
const struct dsa_switch_ops *ds_ops;
const struct realtek_smi_ops *ops;
unsigned int clk_delay;
u8 cmd_read;
u8 cmd_write;
size_t chip_data_sz;
net: dsa: realtek-smi: Add Realtek SMI driver This adds a driver core for the Realtek SMI chips and a subdriver for the RTL8366RB. I just added this chip simply because it is all I can test. The code is a massaged variant of the code that has been sitting out-of-tree in OpenWRT for years in the absence of a proper switch subsystem. This creates a DSA driver for it. I have tried to credit the original authors wherever possible. The main changes I've done from the OpenWRT code: - Added an IRQ chip inside the RTL8366RB switch to demux and handle the line state IRQs. - Distributed the phy handling out to the PHY driver. - Added some RTL8366RB code that was missing in the driver at the time, such as setting up "green ethernet" with a funny jam table and forcing MAC5 (the CPU port) into 1 GBit. - Select jam table and add the default jam table from the vendor driver, also for ASIC "version 0" if need be. - Do not store jam tables in the device tree, store them in the driver. - Pick in the "initvals" jam tables from OpenWRT's driver and make those get selected per compatible for the whole system. It's apparently about electrical settings for this system and whatnot, not really configuration from device tree. - Implemented LED control: beware of bugs because there are no LEDs on the device I am using! We do not implement custom DSA tags. This is explained in a comment in the driver as well: this "tagging protocol" is not simply a few extra bytes tagged on to the ethernet frame as DSA is used to. Instead, enabling the CPU tags will make the switch start talking Realtek RRCP internally. For example a simple ping will make this kind of packets appear inside the switch: 0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00 0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d 0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00 0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 As you can see a custom "8899" tagged packet using the protocol 0xa2. Norm RRCP appears to always have this protocol set to 0x01 according to OpenRRCP. You can also see that this is not a ping packet at all, instead the switch is starting to talk network management issues with the CPU port. So for now custom "tagging" is disabled. This was tested on the D-Link DIR-685 with initramfs and OpenWRT userspaces and works fine on all the LAN ports (lan0 .. lan3). The WAN port is yet not working. Cc: Antti Seppälä <a.seppala@gmail.com> Cc: Roman Yeryomin <roman@advem.lv> Cc: Colin Leitner <colin.leitner@googlemail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14 12:45:55 +03:00
};
/* SMI core calls */
int realtek_smi_write_reg_noack(struct realtek_smi *smi, u32 addr,
u32 data);
int realtek_smi_setup_mdio(struct realtek_smi *smi);
/* RTL8366 library helpers */
int rtl8366_mc_is_used(struct realtek_smi *smi, int mc_index, int *used);
int rtl8366_set_vlan(struct realtek_smi *smi, int vid, u32 member,
u32 untag, u32 fid);
int rtl8366_set_pvid(struct realtek_smi *smi, unsigned int port,
unsigned int vid);
int rtl8366_enable_vlan4k(struct realtek_smi *smi, bool enable);
int rtl8366_enable_vlan(struct realtek_smi *smi, bool enable);
int rtl8366_reset_vlan(struct realtek_smi *smi);
int rtl8366_init_vlan(struct realtek_smi *smi);
int rtl8366_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
struct netlink_ext_ack *extack);
net: dsa: remove the transactional logic from VLAN objects It should be the driver's business to logically separate its VLAN offloading into a preparation and a commit phase, and some drivers don't need / can't do this. So remove the transactional shim from DSA and let drivers propagate errors directly from the .port_vlan_add callback. It would appear that the code has worse error handling now than it had before. DSA is the only in-kernel user of switchdev that offloads one switchdev object to more than one port: for every VLAN object offloaded to a user port, that VLAN is also offloaded to the CPU port. So the "prepare for user port -> check for errors -> prepare for CPU port -> check for errors -> commit for user port -> commit for CPU port" sequence appears to make more sense than the one we are using now: "offload to user port -> check for errors -> offload to CPU port -> check for errors", but it is really a compromise. In the new way, we can catch errors from the commit phase that we previously had to ignore. But we have our hands tied and cannot do any rollback now: if we add a VLAN on the CPU port and it fails, we can't do the rollback by simply deleting it from the user port, because the switchdev API is not so nice with us: it could have simply been there already, even with the same flags. So we don't even attempt to rollback anything on addition error, just leave whatever VLANs managed to get offloaded right where they are. This should not be a problem at all in practice. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-09 03:01:53 +03:00
int rtl8366_vlan_add(struct dsa_switch *ds, int port,
const struct switchdev_obj_port_vlan *vlan,
struct netlink_ext_ack *extack);
net: dsa: realtek-smi: Add Realtek SMI driver This adds a driver core for the Realtek SMI chips and a subdriver for the RTL8366RB. I just added this chip simply because it is all I can test. The code is a massaged variant of the code that has been sitting out-of-tree in OpenWRT for years in the absence of a proper switch subsystem. This creates a DSA driver for it. I have tried to credit the original authors wherever possible. The main changes I've done from the OpenWRT code: - Added an IRQ chip inside the RTL8366RB switch to demux and handle the line state IRQs. - Distributed the phy handling out to the PHY driver. - Added some RTL8366RB code that was missing in the driver at the time, such as setting up "green ethernet" with a funny jam table and forcing MAC5 (the CPU port) into 1 GBit. - Select jam table and add the default jam table from the vendor driver, also for ASIC "version 0" if need be. - Do not store jam tables in the device tree, store them in the driver. - Pick in the "initvals" jam tables from OpenWRT's driver and make those get selected per compatible for the whole system. It's apparently about electrical settings for this system and whatnot, not really configuration from device tree. - Implemented LED control: beware of bugs because there are no LEDs on the device I am using! We do not implement custom DSA tags. This is explained in a comment in the driver as well: this "tagging protocol" is not simply a few extra bytes tagged on to the ethernet frame as DSA is used to. Instead, enabling the CPU tags will make the switch start talking Realtek RRCP internally. For example a simple ping will make this kind of packets appear inside the switch: 0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00 0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d 0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00 0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 As you can see a custom "8899" tagged packet using the protocol 0xa2. Norm RRCP appears to always have this protocol set to 0x01 according to OpenRRCP. You can also see that this is not a ping packet at all, instead the switch is starting to talk network management issues with the CPU port. So for now custom "tagging" is disabled. This was tested on the D-Link DIR-685 with initramfs and OpenWRT userspaces and works fine on all the LAN ports (lan0 .. lan3). The WAN port is yet not working. Cc: Antti Seppälä <a.seppala@gmail.com> Cc: Roman Yeryomin <roman@advem.lv> Cc: Colin Leitner <colin.leitner@googlemail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-14 12:45:55 +03:00
int rtl8366_vlan_del(struct dsa_switch *ds, int port,
const struct switchdev_obj_port_vlan *vlan);
void rtl8366_get_strings(struct dsa_switch *ds, int port, u32 stringset,
uint8_t *data);
int rtl8366_get_sset_count(struct dsa_switch *ds, int port, int sset);
void rtl8366_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *data);
extern const struct realtek_smi_variant rtl8366rb_variant;
#endif /* _REALTEK_SMI_H */