WSL2-Linux-Kernel/fs/xfs/xfs_iomap.c

924 строки
25 KiB
C
Исходник Обычный вид История

/*
* Copyright (c) 2000-2006 Silicon Graphics, Inc.
* All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it would be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write the Free Software Foundation,
* Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include "xfs.h"
#include "xfs_fs.h"
#include "xfs_log.h"
#include "xfs_trans.h"
#include "xfs_sb.h"
#include "xfs_ag.h"
#include "xfs_alloc.h"
#include "xfs_quota.h"
#include "xfs_mount.h"
#include "xfs_bmap_btree.h"
#include "xfs_alloc_btree.h"
#include "xfs_ialloc_btree.h"
#include "xfs_dinode.h"
#include "xfs_inode.h"
#include "xfs_inode_item.h"
#include "xfs_btree.h"
#include "xfs_bmap.h"
#include "xfs_rtalloc.h"
#include "xfs_error.h"
#include "xfs_itable.h"
#include "xfs_attr.h"
#include "xfs_buf_item.h"
#include "xfs_trans_space.h"
#include "xfs_utils.h"
#include "xfs_iomap.h"
xfs: event tracing support Convert the old xfs tracing support that could only be used with the out of tree kdb and xfsidbg patches to use the generic event tracer. To use it make sure CONFIG_EVENT_TRACING is enabled and then enable all xfs trace channels by: echo 1 > /sys/kernel/debug/tracing/events/xfs/enable or alternatively enable single events by just doing the same in one event subdirectory, e.g. echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable or set more complex filters, etc. In Documentation/trace/events.txt all this is desctribed in more detail. To reads the events do a cat /sys/kernel/debug/tracing/trace Compared to the last posting this patch converts the tracing mostly to the one tracepoint per callsite model that other users of the new tracing facility also employ. This allows a very fine-grained control of the tracing, a cleaner output of the traces and also enables the perf tool to use each tracepoint as a virtual performance counter, allowing us to e.g. count how often certain workloads git various spots in XFS. Take a look at http://lwn.net/Articles/346470/ for some examples. Also the btree tracing isn't included at all yet, as it will require additional core tracing features not in mainline yet, I plan to deliver it later. And the really nice thing about this patch is that it actually removes many lines of code while adding this nice functionality: fs/xfs/Makefile | 8 fs/xfs/linux-2.6/xfs_acl.c | 1 fs/xfs/linux-2.6/xfs_aops.c | 52 - fs/xfs/linux-2.6/xfs_aops.h | 2 fs/xfs/linux-2.6/xfs_buf.c | 117 +-- fs/xfs/linux-2.6/xfs_buf.h | 33 fs/xfs/linux-2.6/xfs_fs_subr.c | 3 fs/xfs/linux-2.6/xfs_ioctl.c | 1 fs/xfs/linux-2.6/xfs_ioctl32.c | 1 fs/xfs/linux-2.6/xfs_iops.c | 1 fs/xfs/linux-2.6/xfs_linux.h | 1 fs/xfs/linux-2.6/xfs_lrw.c | 87 -- fs/xfs/linux-2.6/xfs_lrw.h | 45 - fs/xfs/linux-2.6/xfs_super.c | 104 --- fs/xfs/linux-2.6/xfs_super.h | 7 fs/xfs/linux-2.6/xfs_sync.c | 1 fs/xfs/linux-2.6/xfs_trace.c | 75 ++ fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++ fs/xfs/linux-2.6/xfs_vnode.h | 4 fs/xfs/quota/xfs_dquot.c | 110 --- fs/xfs/quota/xfs_dquot.h | 21 fs/xfs/quota/xfs_qm.c | 40 - fs/xfs/quota/xfs_qm_syscalls.c | 4 fs/xfs/support/ktrace.c | 323 --------- fs/xfs/support/ktrace.h | 85 -- fs/xfs/xfs.h | 16 fs/xfs/xfs_ag.h | 14 fs/xfs/xfs_alloc.c | 230 +----- fs/xfs/xfs_alloc.h | 27 fs/xfs/xfs_alloc_btree.c | 1 fs/xfs/xfs_attr.c | 107 --- fs/xfs/xfs_attr.h | 10 fs/xfs/xfs_attr_leaf.c | 14 fs/xfs/xfs_attr_sf.h | 40 - fs/xfs/xfs_bmap.c | 507 +++------------ fs/xfs/xfs_bmap.h | 49 - fs/xfs/xfs_bmap_btree.c | 6 fs/xfs/xfs_btree.c | 5 fs/xfs/xfs_btree_trace.h | 17 fs/xfs/xfs_buf_item.c | 87 -- fs/xfs/xfs_buf_item.h | 20 fs/xfs/xfs_da_btree.c | 3 fs/xfs/xfs_da_btree.h | 7 fs/xfs/xfs_dfrag.c | 2 fs/xfs/xfs_dir2.c | 8 fs/xfs/xfs_dir2_block.c | 20 fs/xfs/xfs_dir2_leaf.c | 21 fs/xfs/xfs_dir2_node.c | 27 fs/xfs/xfs_dir2_sf.c | 26 fs/xfs/xfs_dir2_trace.c | 216 ------ fs/xfs/xfs_dir2_trace.h | 72 -- fs/xfs/xfs_filestream.c | 8 fs/xfs/xfs_fsops.c | 2 fs/xfs/xfs_iget.c | 111 --- fs/xfs/xfs_inode.c | 67 -- fs/xfs/xfs_inode.h | 76 -- fs/xfs/xfs_inode_item.c | 5 fs/xfs/xfs_iomap.c | 85 -- fs/xfs/xfs_iomap.h | 8 fs/xfs/xfs_log.c | 181 +---- fs/xfs/xfs_log_priv.h | 20 fs/xfs/xfs_log_recover.c | 1 fs/xfs/xfs_mount.c | 2 fs/xfs/xfs_quota.h | 8 fs/xfs/xfs_rename.c | 1 fs/xfs/xfs_rtalloc.c | 1 fs/xfs/xfs_rw.c | 3 fs/xfs/xfs_trans.h | 47 + fs/xfs/xfs_trans_buf.c | 62 - fs/xfs/xfs_vnodeops.c | 8 70 files changed, 2151 insertions(+), 2592 deletions(-) Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com>
2009-12-15 02:14:59 +03:00
#include "xfs_trace.h"
#include "xfs_icache.h"
#include "xfs_dquot_item.h"
#include "xfs_dquot.h"
#define XFS_WRITEIO_ALIGN(mp,off) (((off) >> mp->m_writeio_log) \
<< mp->m_writeio_log)
#define XFS_WRITE_IMAPS XFS_BMAP_MAX_NMAP
STATIC int
xfs_iomap_eof_align_last_fsb(
xfs_mount_t *mp,
xfs_inode_t *ip,
xfs_extlen_t extsize,
xfs_fileoff_t *last_fsb)
{
xfs_fileoff_t new_last_fsb = 0;
xfs_extlen_t align = 0;
int eof, error;
if (!XFS_IS_REALTIME_INODE(ip)) {
/*
* Round up the allocation request to a stripe unit
* (m_dalign) boundary if the file size is >= stripe unit
* size, and we are allocating past the allocation eof.
*
* If mounted with the "-o swalloc" option the alignment is
* increased from the strip unit size to the stripe width.
*/
if (mp->m_swidth && (mp->m_flags & XFS_MOUNT_SWALLOC))
align = mp->m_swidth;
else if (mp->m_dalign)
align = mp->m_dalign;
if (align && XFS_ISIZE(ip) >= XFS_FSB_TO_B(mp, align))
new_last_fsb = roundup_64(*last_fsb, align);
}
/*
* Always round up the allocation request to an extent boundary
* (when file on a real-time subvolume or has di_extsize hint).
*/
if (extsize) {
if (new_last_fsb)
align = roundup_64(new_last_fsb, extsize);
else
align = extsize;
new_last_fsb = roundup_64(*last_fsb, align);
}
if (new_last_fsb) {
error = xfs_bmap_eof(ip, new_last_fsb, XFS_DATA_FORK, &eof);
if (error)
return error;
if (eof)
*last_fsb = new_last_fsb;
}
return 0;
}
STATIC int
xfs_alert_fsblock_zero(
xfs_inode_t *ip,
xfs_bmbt_irec_t *imap)
{
xfs_alert_tag(ip->i_mount, XFS_PTAG_FSBLOCK_ZERO,
"Access to block zero in inode %llu "
"start_block: %llx start_off: %llx "
"blkcnt: %llx extent-state: %x\n",
(unsigned long long)ip->i_ino,
(unsigned long long)imap->br_startblock,
(unsigned long long)imap->br_startoff,
(unsigned long long)imap->br_blockcount,
imap->br_state);
return EFSCORRUPTED;
}
int
xfs_iomap_write_direct(
xfs_inode_t *ip,
xfs_off_t offset,
size_t count,
xfs_bmbt_irec_t *imap,
int nmaps)
{
xfs_mount_t *mp = ip->i_mount;
xfs_fileoff_t offset_fsb;
xfs_fileoff_t last_fsb;
xfs_filblks_t count_fsb, resaligned;
xfs_fsblock_t firstfsb;
xfs_extlen_t extsz, temp;
int nimaps;
int bmapi_flag;
int quota_flag;
int rt;
xfs_trans_t *tp;
xfs_bmap_free_t free_list;
uint qblocks, resblks, resrtextents;
int committed;
int error;
error = xfs_qm_dqattach(ip, 0);
if (error)
return XFS_ERROR(error);
rt = XFS_IS_REALTIME_INODE(ip);
extsz = xfs_get_extsz_hint(ip);
offset_fsb = XFS_B_TO_FSBT(mp, offset);
last_fsb = XFS_B_TO_FSB(mp, ((xfs_ufsize_t)(offset + count)));
if ((offset + count) > XFS_ISIZE(ip)) {
error = xfs_iomap_eof_align_last_fsb(mp, ip, extsz, &last_fsb);
if (error)
return XFS_ERROR(error);
} else {
if (nmaps && (imap->br_startblock == HOLESTARTBLOCK))
last_fsb = MIN(last_fsb, (xfs_fileoff_t)
imap->br_blockcount +
imap->br_startoff);
}
count_fsb = last_fsb - offset_fsb;
ASSERT(count_fsb > 0);
resaligned = count_fsb;
if (unlikely(extsz)) {
if ((temp = do_mod(offset_fsb, extsz)))
resaligned += temp;
if ((temp = do_mod(resaligned, extsz)))
resaligned += extsz - temp;
}
if (unlikely(rt)) {
resrtextents = qblocks = resaligned;
resrtextents /= mp->m_sb.sb_rextsize;
resblks = XFS_DIOSTRAT_SPACE_RES(mp, 0);
quota_flag = XFS_QMOPT_RES_RTBLKS;
} else {
resrtextents = 0;
resblks = qblocks = XFS_DIOSTRAT_SPACE_RES(mp, resaligned);
quota_flag = XFS_QMOPT_RES_REGBLKS;
}
/*
* Allocate and setup the transaction
*/
tp = xfs_trans_alloc(mp, XFS_TRANS_DIOSTRAT);
error = xfs_trans_reserve(tp, resblks,
XFS_WRITE_LOG_RES(mp), resrtextents,
XFS_TRANS_PERM_LOG_RES,
XFS_WRITE_LOG_COUNT);
/*
* Check for running out of space, note: need lock to return
*/
if (error) {
xfs_trans_cancel(tp, 0);
return XFS_ERROR(error);
}
xfs_ilock(ip, XFS_ILOCK_EXCL);
error = xfs_trans_reserve_quota_nblks(tp, ip, qblocks, 0, quota_flag);
if (error)
goto out_trans_cancel;
xfs_trans_ijoin(tp, ip, 0);
bmapi_flag = 0;
if (offset < XFS_ISIZE(ip) || extsz)
bmapi_flag |= XFS_BMAPI_PREALLOC;
/*
* From this point onwards we overwrite the imap pointer that the
* caller gave to us.
*/
xfs_bmap_init(&free_list, &firstfsb);
nimaps = 1;
error = xfs_bmapi_write(tp, ip, offset_fsb, count_fsb, bmapi_flag,
&firstfsb, 0, imap, &nimaps, &free_list);
if (error)
goto out_bmap_cancel;
/*
* Complete the transaction
*/
error = xfs_bmap_finish(&tp, &free_list, &committed);
if (error)
goto out_bmap_cancel;
error = xfs_trans_commit(tp, XFS_TRANS_RELEASE_LOG_RES);
if (error)
goto out_unlock;
/*
* Copy any maps to caller's array and return any error.
*/
if (nimaps == 0) {
error = XFS_ERROR(ENOSPC);
goto out_unlock;
}
if (!(imap->br_startblock || XFS_IS_REALTIME_INODE(ip)))
error = xfs_alert_fsblock_zero(ip, imap);
out_unlock:
xfs_iunlock(ip, XFS_ILOCK_EXCL);
return error;
out_bmap_cancel:
xfs_bmap_cancel(&free_list);
xfs_trans_unreserve_quota_nblks(tp, ip, (long)qblocks, 0, quota_flag);
out_trans_cancel:
xfs_trans_cancel(tp, XFS_TRANS_RELEASE_LOG_RES | XFS_TRANS_ABORT);
goto out_unlock;
}
/*
* If the caller is doing a write at the end of the file, then extend the
* allocation out to the file system's write iosize. We clean up any extra
* space left over when the file is closed in xfs_inactive().
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
*
* If we find we already have delalloc preallocation beyond EOF, don't do more
* preallocation as it it not needed.
*/
STATIC int
xfs_iomap_eof_want_preallocate(
xfs_mount_t *mp,
xfs_inode_t *ip,
xfs_off_t offset,
size_t count,
xfs_bmbt_irec_t *imap,
int nimaps,
int *prealloc)
{
xfs_fileoff_t start_fsb;
xfs_filblks_t count_fsb;
xfs_fsblock_t firstblock;
int n, error, imaps;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
int found_delalloc = 0;
*prealloc = 0;
if (offset + count <= XFS_ISIZE(ip))
return 0;
/*
* If there are any real blocks past eof, then don't
* do any speculative allocation.
*/
start_fsb = XFS_B_TO_FSBT(mp, ((xfs_ufsize_t)(offset + count - 1)));
count_fsb = XFS_B_TO_FSB(mp, mp->m_super->s_maxbytes);
while (count_fsb > 0) {
imaps = nimaps;
firstblock = NULLFSBLOCK;
error = xfs_bmapi_read(ip, start_fsb, count_fsb, imap, &imaps,
0);
if (error)
return error;
for (n = 0; n < imaps; n++) {
if ((imap[n].br_startblock != HOLESTARTBLOCK) &&
(imap[n].br_startblock != DELAYSTARTBLOCK))
return 0;
start_fsb += imap[n].br_blockcount;
count_fsb -= imap[n].br_blockcount;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
if (imap[n].br_startblock == DELAYSTARTBLOCK)
found_delalloc = 1;
}
}
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
if (!found_delalloc)
*prealloc = 1;
return 0;
}
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
/*
* Determine the initial size of the preallocation. We are beyond the current
* EOF here, but we need to take into account whether this is a sparse write or
* an extending write when determining the preallocation size. Hence we need to
* look up the extent that ends at the current write offset and use the result
* to determine the preallocation size.
*
* If the extent is a hole, then preallocation is essentially disabled.
* Otherwise we take the size of the preceeding data extent as the basis for the
* preallocation size. If the size of the extent is greater than half the
* maximum extent length, then use the current offset as the basis. This ensures
* that for large files the preallocation size always extends to MAXEXTLEN
* rather than falling short due to things like stripe unit/width alignment of
* real extents.
*/
STATIC xfs_fsblock_t
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
xfs_iomap_eof_prealloc_initial_size(
struct xfs_mount *mp,
struct xfs_inode *ip,
xfs_off_t offset,
xfs_bmbt_irec_t *imap,
int nimaps)
{
xfs_fileoff_t start_fsb;
int imaps = 1;
int error;
ASSERT(nimaps >= imaps);
/* if we are using a specific prealloc size, return now */
if (mp->m_flags & XFS_MOUNT_DFLT_IOSIZE)
return 0;
/*
* As we write multiple pages, the offset will always align to the
* start of a page and hence point to a hole at EOF. i.e. if the size is
* 4096 bytes, we only have one block at FSB 0, but XFS_B_TO_FSB(4096)
* will return FSB 1. Hence if there are blocks in the file, we want to
* point to the block prior to the EOF block and not the hole that maps
* directly at @offset.
*/
start_fsb = XFS_B_TO_FSB(mp, offset);
if (start_fsb)
start_fsb--;
error = xfs_bmapi_read(ip, start_fsb, 1, imap, &imaps, XFS_BMAPI_ENTIRE);
if (error)
return 0;
ASSERT(imaps == 1);
if (imap[0].br_startblock == HOLESTARTBLOCK)
return 0;
if (imap[0].br_blockcount <= (MAXEXTLEN >> 1))
return imap[0].br_blockcount << 1;
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
return XFS_B_TO_FSB(mp, offset);
}
STATIC bool
xfs_quota_need_throttle(
struct xfs_inode *ip,
int type,
xfs_fsblock_t alloc_blocks)
{
struct xfs_dquot *dq = xfs_inode_dquot(ip, type);
if (!dq || !xfs_this_quota_on(ip->i_mount, type))
return false;
/* no hi watermark, no throttle */
if (!dq->q_prealloc_hi_wmark)
return false;
/* under the lo watermark, no throttle */
if (dq->q_res_bcount + alloc_blocks < dq->q_prealloc_lo_wmark)
return false;
return true;
}
STATIC void
xfs_quota_calc_throttle(
struct xfs_inode *ip,
int type,
xfs_fsblock_t *qblocks,
int *qshift)
{
int64_t freesp;
int shift = 0;
struct xfs_dquot *dq = xfs_inode_dquot(ip, type);
/* over hi wmark, squash the prealloc completely */
if (dq->q_res_bcount >= dq->q_prealloc_hi_wmark) {
*qblocks = 0;
return;
}
freesp = dq->q_prealloc_hi_wmark - dq->q_res_bcount;
if (freesp < dq->q_low_space[XFS_QLOWSP_5_PCNT]) {
shift = 2;
if (freesp < dq->q_low_space[XFS_QLOWSP_3_PCNT])
shift += 2;
if (freesp < dq->q_low_space[XFS_QLOWSP_1_PCNT])
shift += 2;
}
/* only overwrite the throttle values if we are more aggressive */
if ((freesp >> shift) < (*qblocks >> *qshift)) {
*qblocks = freesp;
*qshift = shift;
}
}
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
/*
* If we don't have a user specified preallocation size, dynamically increase
* the preallocation size as the size of the file grows. Cap the maximum size
* at a single extent or less if the filesystem is near full. The closer the
* filesystem is to full, the smaller the maximum prealocation.
*/
STATIC xfs_fsblock_t
xfs_iomap_prealloc_size(
struct xfs_mount *mp,
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
struct xfs_inode *ip,
xfs_off_t offset,
struct xfs_bmbt_irec *imap,
int nimaps)
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
{
xfs_fsblock_t alloc_blocks = 0;
int shift = 0;
int64_t freesp;
xfs_fsblock_t qblocks;
int qshift = 0;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
alloc_blocks = xfs_iomap_eof_prealloc_initial_size(mp, ip, offset,
imap, nimaps);
if (!alloc_blocks)
goto check_writeio;
qblocks = alloc_blocks;
/*
* MAXEXTLEN is not a power of two value but we round the prealloc down
* to the nearest power of two value after throttling. To prevent the
* round down from unconditionally reducing the maximum supported prealloc
* size, we round up first, apply appropriate throttling, round down and
* cap the value to MAXEXTLEN.
*/
alloc_blocks = XFS_FILEOFF_MIN(roundup_pow_of_two(MAXEXTLEN),
alloc_blocks);
xfs_icsb_sync_counters(mp, XFS_ICSB_LAZY_COUNT);
freesp = mp->m_sb.sb_fdblocks;
if (freesp < mp->m_low_space[XFS_LOWSP_5_PCNT]) {
shift = 2;
if (freesp < mp->m_low_space[XFS_LOWSP_4_PCNT])
shift++;
if (freesp < mp->m_low_space[XFS_LOWSP_3_PCNT])
shift++;
if (freesp < mp->m_low_space[XFS_LOWSP_2_PCNT])
shift++;
if (freesp < mp->m_low_space[XFS_LOWSP_1_PCNT])
shift++;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
}
/*
* Check each quota to cap the prealloc size and provide a shift
* value to throttle with.
*/
if (xfs_quota_need_throttle(ip, XFS_DQ_USER, alloc_blocks))
xfs_quota_calc_throttle(ip, XFS_DQ_USER, &qblocks, &qshift);
if (xfs_quota_need_throttle(ip, XFS_DQ_GROUP, alloc_blocks))
xfs_quota_calc_throttle(ip, XFS_DQ_GROUP, &qblocks, &qshift);
if (xfs_quota_need_throttle(ip, XFS_DQ_PROJ, alloc_blocks))
xfs_quota_calc_throttle(ip, XFS_DQ_PROJ, &qblocks, &qshift);
/*
* The final prealloc size is set to the minimum of free space available
* in each of the quotas and the overall filesystem.
*
* The shift throttle value is set to the maximum value as determined by
* the global low free space values and per-quota low free space values.
*/
alloc_blocks = MIN(alloc_blocks, qblocks);
shift = MAX(shift, qshift);
if (shift)
alloc_blocks >>= shift;
/*
* rounddown_pow_of_two() returns an undefined result if we pass in
* alloc_blocks = 0.
*/
if (alloc_blocks)
alloc_blocks = rounddown_pow_of_two(alloc_blocks);
if (alloc_blocks > MAXEXTLEN)
alloc_blocks = MAXEXTLEN;
/*
* If we are still trying to allocate more space than is
* available, squash the prealloc hard. This can happen if we
* have a large file on a small filesystem and the above
* lowspace thresholds are smaller than MAXEXTLEN.
*/
while (alloc_blocks && alloc_blocks >= freesp)
alloc_blocks >>= 4;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
check_writeio:
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
if (alloc_blocks < mp->m_writeio_blocks)
alloc_blocks = mp->m_writeio_blocks;
trace_xfs_iomap_prealloc_size(ip, alloc_blocks, shift,
mp->m_writeio_blocks);
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
return alloc_blocks;
}
int
xfs_iomap_write_delay(
xfs_inode_t *ip,
xfs_off_t offset,
size_t count,
xfs_bmbt_irec_t *ret_imap)
{
xfs_mount_t *mp = ip->i_mount;
xfs_fileoff_t offset_fsb;
xfs_fileoff_t last_fsb;
xfs_off_t aligned_offset;
xfs_fileoff_t ioalign;
xfs_extlen_t extsz;
int nimaps;
xfs_bmbt_irec_t imap[XFS_WRITE_IMAPS];
xfs: xfs_sync_data is redundant. We don't do any data writeback from XFS any more - the VFS is completely responsible for that, including for freeze. We can replace the remaining caller with a VFS level function that achieves the same thing, but without conflicting with current writeback work. This means we can remove the flush_work and xfs_flush_inodes() - the VFS functionality completely replaces the internal flush queue for doing this writeback work in a separate context to avoid stack overruns. This does have one complication - it cannot be called with page locks held. Hence move the flushing of delalloc space when ENOSPC occurs back up into xfs_file_aio_buffered_write when we don't hold any locks that will stall writeback. Unfortunately, writeback_inodes_sb_if_idle() is not sufficient to trigger delalloc conversion fast enough to prevent spurious ENOSPC whent here are hundreds of writers, thousands of small files and GBs of free RAM. Hence we need to use sync_sb_inodes() to block callers while we wait for writeback like the previous xfs_flush_inodes implementation did. That means we have to hold the s_umount lock here, but because this call can nest inside i_mutex (the parent directory in the create case, held by the VFS), we have to use down_read_trylock() to avoid potential deadlocks. In practice, this trylock will succeed on almost every attempt as unmount/remount type operations are exceedingly rare. Note: we always need to pass a count of zero to generic_file_buffered_write() as the previously written byte count. We only do this by accident before this patch by the virtue of ret always being zero when there are no errors. Make this explicit rather than needing to specifically zero ret in the ENOSPC retry case. Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
2012-10-08 14:56:04 +04:00
int prealloc;
int error;
ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL));
/*
* Make sure that the dquots are there. This doesn't hold
* the ilock across a disk read.
*/
error = xfs_qm_dqattach_locked(ip, 0);
if (error)
return XFS_ERROR(error);
extsz = xfs_get_extsz_hint(ip);
offset_fsb = XFS_B_TO_FSBT(mp, offset);
error = xfs_iomap_eof_want_preallocate(mp, ip, offset, count,
imap, XFS_WRITE_IMAPS, &prealloc);
if (error)
return error;
retry:
if (prealloc) {
xfs: limit speculative prealloc size on sparse files Speculative preallocation based on the current file size works well for contiguous files, but is sub-optimal for sparse files where the EOF preallocation can fill holes and result in large amounts of zeros being written when it is not necessary. The algorithm is modified to prevent EOF speculative preallocation from triggering larger allocations on IO patterns of truncate--to-zero-seek-write-seek-write-.... which results in non-sparse files for large files. This, unfortunately, is the way cp now behaves when copying sparse files and so needs to be fixed. What this code does is that it looks at the existing extent adjacent to the current EOF and if it determines that it is a hole we disable speculative preallocation altogether. To avoid the next write from doing a large prealloc, it takes the size of subsequent preallocations from the current size of the existing EOF extent. IOWs, if you leave a hole in the file, it resets preallocation behaviour to the same as if it was a zero size file. Example new behaviour: $ xfs_io -f -c "pwrite 0 31m" \ -c "pwrite 33m 1m" \ -c "pwrite 128m 1m" \ -c "fiemap -v" /mnt/scratch/blah wrote 32505856/32505856 bytes at offset 0 31 MiB, 7936 ops; 0.0000 sec (1.608 GiB/sec and 421432.7439 ops/sec) wrote 1048576/1048576 bytes at offset 34603008 1 MiB, 256 ops; 0.0000 sec (1.462 GiB/sec and 383233.5329 ops/sec) wrote 1048576/1048576 bytes at offset 134217728 1 MiB, 256 ops; 0.0000 sec (1.719 GiB/sec and 450704.2254 ops/sec) /mnt/scratch/blah: EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS 0: [0..65535]: 96..65631 65536 0x0 1: [65536..67583]: hole 2048 2: [67584..69631]: 67680..69727 2048 0x0 3: [69632..262143]: hole 192512 4: [262144..264191]: 262240..264287 2048 0x1 Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
2013-02-11 09:05:01 +04:00
xfs_fsblock_t alloc_blocks;
alloc_blocks = xfs_iomap_prealloc_size(mp, ip, offset, imap,
XFS_WRITE_IMAPS);
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
aligned_offset = XFS_WRITEIO_ALIGN(mp, (offset + count - 1));
ioalign = XFS_B_TO_FSBT(mp, aligned_offset);
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
last_fsb = ioalign + alloc_blocks;
} else {
last_fsb = XFS_B_TO_FSB(mp, ((xfs_ufsize_t)(offset + count)));
}
if (prealloc || extsz) {
error = xfs_iomap_eof_align_last_fsb(mp, ip, extsz, &last_fsb);
if (error)
return error;
}
/*
* Make sure preallocation does not create extents beyond the range we
* actually support in this filesystem.
*/
if (last_fsb > XFS_B_TO_FSB(mp, mp->m_super->s_maxbytes))
last_fsb = XFS_B_TO_FSB(mp, mp->m_super->s_maxbytes);
ASSERT(last_fsb > offset_fsb);
nimaps = XFS_WRITE_IMAPS;
error = xfs_bmapi_delay(ip, offset_fsb, last_fsb - offset_fsb,
imap, &nimaps, XFS_BMAPI_ENTIRE);
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
switch (error) {
case 0:
case ENOSPC:
case EDQUOT:
break;
default:
return XFS_ERROR(error);
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
}
/*
xfs: xfs_sync_data is redundant. We don't do any data writeback from XFS any more - the VFS is completely responsible for that, including for freeze. We can replace the remaining caller with a VFS level function that achieves the same thing, but without conflicting with current writeback work. This means we can remove the flush_work and xfs_flush_inodes() - the VFS functionality completely replaces the internal flush queue for doing this writeback work in a separate context to avoid stack overruns. This does have one complication - it cannot be called with page locks held. Hence move the flushing of delalloc space when ENOSPC occurs back up into xfs_file_aio_buffered_write when we don't hold any locks that will stall writeback. Unfortunately, writeback_inodes_sb_if_idle() is not sufficient to trigger delalloc conversion fast enough to prevent spurious ENOSPC whent here are hundreds of writers, thousands of small files and GBs of free RAM. Hence we need to use sync_sb_inodes() to block callers while we wait for writeback like the previous xfs_flush_inodes implementation did. That means we have to hold the s_umount lock here, but because this call can nest inside i_mutex (the parent directory in the create case, held by the VFS), we have to use down_read_trylock() to avoid potential deadlocks. In practice, this trylock will succeed on almost every attempt as unmount/remount type operations are exceedingly rare. Note: we always need to pass a count of zero to generic_file_buffered_write() as the previously written byte count. We only do this by accident before this patch by the virtue of ret always being zero when there are no errors. Make this explicit rather than needing to specifically zero ret in the ENOSPC retry case. Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
2012-10-08 14:56:04 +04:00
* If bmapi returned us nothing, we got either ENOSPC or EDQUOT. Retry
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
* without EOF preallocation.
*/
if (nimaps == 0) {
xfs: event tracing support Convert the old xfs tracing support that could only be used with the out of tree kdb and xfsidbg patches to use the generic event tracer. To use it make sure CONFIG_EVENT_TRACING is enabled and then enable all xfs trace channels by: echo 1 > /sys/kernel/debug/tracing/events/xfs/enable or alternatively enable single events by just doing the same in one event subdirectory, e.g. echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable or set more complex filters, etc. In Documentation/trace/events.txt all this is desctribed in more detail. To reads the events do a cat /sys/kernel/debug/tracing/trace Compared to the last posting this patch converts the tracing mostly to the one tracepoint per callsite model that other users of the new tracing facility also employ. This allows a very fine-grained control of the tracing, a cleaner output of the traces and also enables the perf tool to use each tracepoint as a virtual performance counter, allowing us to e.g. count how often certain workloads git various spots in XFS. Take a look at http://lwn.net/Articles/346470/ for some examples. Also the btree tracing isn't included at all yet, as it will require additional core tracing features not in mainline yet, I plan to deliver it later. And the really nice thing about this patch is that it actually removes many lines of code while adding this nice functionality: fs/xfs/Makefile | 8 fs/xfs/linux-2.6/xfs_acl.c | 1 fs/xfs/linux-2.6/xfs_aops.c | 52 - fs/xfs/linux-2.6/xfs_aops.h | 2 fs/xfs/linux-2.6/xfs_buf.c | 117 +-- fs/xfs/linux-2.6/xfs_buf.h | 33 fs/xfs/linux-2.6/xfs_fs_subr.c | 3 fs/xfs/linux-2.6/xfs_ioctl.c | 1 fs/xfs/linux-2.6/xfs_ioctl32.c | 1 fs/xfs/linux-2.6/xfs_iops.c | 1 fs/xfs/linux-2.6/xfs_linux.h | 1 fs/xfs/linux-2.6/xfs_lrw.c | 87 -- fs/xfs/linux-2.6/xfs_lrw.h | 45 - fs/xfs/linux-2.6/xfs_super.c | 104 --- fs/xfs/linux-2.6/xfs_super.h | 7 fs/xfs/linux-2.6/xfs_sync.c | 1 fs/xfs/linux-2.6/xfs_trace.c | 75 ++ fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++ fs/xfs/linux-2.6/xfs_vnode.h | 4 fs/xfs/quota/xfs_dquot.c | 110 --- fs/xfs/quota/xfs_dquot.h | 21 fs/xfs/quota/xfs_qm.c | 40 - fs/xfs/quota/xfs_qm_syscalls.c | 4 fs/xfs/support/ktrace.c | 323 --------- fs/xfs/support/ktrace.h | 85 -- fs/xfs/xfs.h | 16 fs/xfs/xfs_ag.h | 14 fs/xfs/xfs_alloc.c | 230 +----- fs/xfs/xfs_alloc.h | 27 fs/xfs/xfs_alloc_btree.c | 1 fs/xfs/xfs_attr.c | 107 --- fs/xfs/xfs_attr.h | 10 fs/xfs/xfs_attr_leaf.c | 14 fs/xfs/xfs_attr_sf.h | 40 - fs/xfs/xfs_bmap.c | 507 +++------------ fs/xfs/xfs_bmap.h | 49 - fs/xfs/xfs_bmap_btree.c | 6 fs/xfs/xfs_btree.c | 5 fs/xfs/xfs_btree_trace.h | 17 fs/xfs/xfs_buf_item.c | 87 -- fs/xfs/xfs_buf_item.h | 20 fs/xfs/xfs_da_btree.c | 3 fs/xfs/xfs_da_btree.h | 7 fs/xfs/xfs_dfrag.c | 2 fs/xfs/xfs_dir2.c | 8 fs/xfs/xfs_dir2_block.c | 20 fs/xfs/xfs_dir2_leaf.c | 21 fs/xfs/xfs_dir2_node.c | 27 fs/xfs/xfs_dir2_sf.c | 26 fs/xfs/xfs_dir2_trace.c | 216 ------ fs/xfs/xfs_dir2_trace.h | 72 -- fs/xfs/xfs_filestream.c | 8 fs/xfs/xfs_fsops.c | 2 fs/xfs/xfs_iget.c | 111 --- fs/xfs/xfs_inode.c | 67 -- fs/xfs/xfs_inode.h | 76 -- fs/xfs/xfs_inode_item.c | 5 fs/xfs/xfs_iomap.c | 85 -- fs/xfs/xfs_iomap.h | 8 fs/xfs/xfs_log.c | 181 +---- fs/xfs/xfs_log_priv.h | 20 fs/xfs/xfs_log_recover.c | 1 fs/xfs/xfs_mount.c | 2 fs/xfs/xfs_quota.h | 8 fs/xfs/xfs_rename.c | 1 fs/xfs/xfs_rtalloc.c | 1 fs/xfs/xfs_rw.c | 3 fs/xfs/xfs_trans.h | 47 + fs/xfs/xfs_trans_buf.c | 62 - fs/xfs/xfs_vnodeops.c | 8 70 files changed, 2151 insertions(+), 2592 deletions(-) Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com>
2009-12-15 02:14:59 +03:00
trace_xfs_delalloc_enospc(ip, offset, count);
xfs: xfs_sync_data is redundant. We don't do any data writeback from XFS any more - the VFS is completely responsible for that, including for freeze. We can replace the remaining caller with a VFS level function that achieves the same thing, but without conflicting with current writeback work. This means we can remove the flush_work and xfs_flush_inodes() - the VFS functionality completely replaces the internal flush queue for doing this writeback work in a separate context to avoid stack overruns. This does have one complication - it cannot be called with page locks held. Hence move the flushing of delalloc space when ENOSPC occurs back up into xfs_file_aio_buffered_write when we don't hold any locks that will stall writeback. Unfortunately, writeback_inodes_sb_if_idle() is not sufficient to trigger delalloc conversion fast enough to prevent spurious ENOSPC whent here are hundreds of writers, thousands of small files and GBs of free RAM. Hence we need to use sync_sb_inodes() to block callers while we wait for writeback like the previous xfs_flush_inodes implementation did. That means we have to hold the s_umount lock here, but because this call can nest inside i_mutex (the parent directory in the create case, held by the VFS), we have to use down_read_trylock() to avoid potential deadlocks. In practice, this trylock will succeed on almost every attempt as unmount/remount type operations are exceedingly rare. Note: we always need to pass a count of zero to generic_file_buffered_write() as the previously written byte count. We only do this by accident before this patch by the virtue of ret always being zero when there are no errors. Make this explicit rather than needing to specifically zero ret in the ENOSPC retry case. Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
2012-10-08 14:56:04 +04:00
if (prealloc) {
prealloc = 0;
error = 0;
goto retry;
xfs: dynamic speculative EOF preallocation Currently the size of the speculative preallocation during delayed allocation is fixed by either the allocsize mount option of a default size. We are seeing a lot of cases where we need to recommend using the allocsize mount option to prevent fragmentation when buffered writes land in the same AG. Rather than using a fixed preallocation size by default (up to 64k), make it dynamic by basing it on the current inode size. That way the EOF preallocation will increase as the file size increases. Hence for streaming writes we are much more likely to get large preallocations exactly when we need it to reduce fragementation. For default settings, the size of the initial extents is determined by the number of parallel writers and the amount of memory in the machine. For 4GB RAM and 4 concurrent 32GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..1048575]: 1048672..2097247 0 (1048672..2097247) 1048576 1: [1048576..2097151]: 5242976..6291551 0 (5242976..6291551) 1048576 2: [2097152..4194303]: 12583008..14680159 0 (12583008..14680159) 2097152 3: [4194304..8388607]: 25165920..29360223 0 (25165920..29360223) 4194304 4: [8388608..16777215]: 58720352..67108959 0 (58720352..67108959) 8388608 5: [16777216..33554423]: 117440584..134217791 0 (117440584..134217791) 16777208 6: [33554424..50331511]: 184549056..201326143 0 (184549056..201326143) 16777088 7: [50331512..67108599]: 251657408..268434495 0 (251657408..268434495) 16777088 and for 16 concurrent 16GB file writes: EXT: FILE-OFFSET BLOCK-RANGE AG AG-OFFSET TOTAL 0: [0..262143]: 2490472..2752615 0 (2490472..2752615) 262144 1: [262144..524287]: 6291560..6553703 0 (6291560..6553703) 262144 2: [524288..1048575]: 13631592..14155879 0 (13631592..14155879) 524288 3: [1048576..2097151]: 30408808..31457383 0 (30408808..31457383) 1048576 4: [2097152..4194303]: 52428904..54526055 0 (52428904..54526055) 2097152 5: [4194304..8388607]: 104857704..109052007 0 (104857704..109052007) 4194304 6: [8388608..16777215]: 209715304..218103911 0 (209715304..218103911) 8388608 7: [16777216..33554423]: 452984848..469762055 0 (452984848..469762055) 16777208 Because it is hard to take back specualtive preallocation, cases where there are large slow growing log files on a nearly full filesystem may cause premature ENOSPC. Hence as the filesystem nears full, the maximum dynamic prealloc size іs reduced according to this table (based on 4k block size): freespace max prealloc size >5% full extent (8GB) 4-5% 2GB (8GB >> 2) 3-4% 1GB (8GB >> 3) 2-3% 512MB (8GB >> 4) 1-2% 256MB (8GB >> 5) <1% 128MB (8GB >> 6) This should reduce the amount of space held in speculative preallocation for such cases. The allocsize mount option turns off the dynamic behaviour and fixes the prealloc size to whatever the mount option specifies. i.e. the behaviour is unchanged. Signed-off-by: Dave Chinner <dchinner@redhat.com>
2011-01-04 03:35:03 +03:00
}
xfs: xfs_sync_data is redundant. We don't do any data writeback from XFS any more - the VFS is completely responsible for that, including for freeze. We can replace the remaining caller with a VFS level function that achieves the same thing, but without conflicting with current writeback work. This means we can remove the flush_work and xfs_flush_inodes() - the VFS functionality completely replaces the internal flush queue for doing this writeback work in a separate context to avoid stack overruns. This does have one complication - it cannot be called with page locks held. Hence move the flushing of delalloc space when ENOSPC occurs back up into xfs_file_aio_buffered_write when we don't hold any locks that will stall writeback. Unfortunately, writeback_inodes_sb_if_idle() is not sufficient to trigger delalloc conversion fast enough to prevent spurious ENOSPC whent here are hundreds of writers, thousands of small files and GBs of free RAM. Hence we need to use sync_sb_inodes() to block callers while we wait for writeback like the previous xfs_flush_inodes implementation did. That means we have to hold the s_umount lock here, but because this call can nest inside i_mutex (the parent directory in the create case, held by the VFS), we have to use down_read_trylock() to avoid potential deadlocks. In practice, this trylock will succeed on almost every attempt as unmount/remount type operations are exceedingly rare. Note: we always need to pass a count of zero to generic_file_buffered_write() as the previously written byte count. We only do this by accident before this patch by the virtue of ret always being zero when there are no errors. Make this explicit rather than needing to specifically zero ret in the ENOSPC retry case. Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
2012-10-08 14:56:04 +04:00
return XFS_ERROR(error ? error : ENOSPC);
}
if (!(imap[0].br_startblock || XFS_IS_REALTIME_INODE(ip)))
return xfs_alert_fsblock_zero(ip, &imap[0]);
/*
* Tag the inode as speculatively preallocated so we can reclaim this
* space on demand, if necessary.
*/
if (prealloc)
xfs_inode_set_eofblocks_tag(ip);
*ret_imap = imap[0];
return 0;
}
/*
* Pass in a delayed allocate extent, convert it to real extents;
* return to the caller the extent we create which maps on top of
* the originating callers request.
*
* Called without a lock on the inode.
*
* We no longer bother to look at the incoming map - all we have to
* guarantee is that whatever we allocate fills the required range.
*/
int
xfs_iomap_write_allocate(
xfs_inode_t *ip,
xfs_off_t offset,
size_t count,
xfs_bmbt_irec_t *imap)
{
xfs_mount_t *mp = ip->i_mount;
xfs_fileoff_t offset_fsb, last_block;
xfs_fileoff_t end_fsb, map_start_fsb;
xfs_fsblock_t first_block;
xfs_bmap_free_t free_list;
xfs_filblks_t count_fsb;
xfs_trans_t *tp;
int nimaps, committed;
int error = 0;
int nres;
/*
* Make sure that the dquots are there.
*/
error = xfs_qm_dqattach(ip, 0);
if (error)
return XFS_ERROR(error);
offset_fsb = XFS_B_TO_FSBT(mp, offset);
count_fsb = imap->br_blockcount;
map_start_fsb = imap->br_startoff;
XFS_STATS_ADD(xs_xstrat_bytes, XFS_FSB_TO_B(mp, count_fsb));
while (count_fsb != 0) {
/*
* Set up a transaction with which to allocate the
* backing store for the file. Do allocations in a
* loop until we get some space in the range we are
* interested in. The other space that might be allocated
* is in the delayed allocation extent on which we sit
* but before our buffer starts.
*/
nimaps = 0;
while (nimaps == 0) {
tp = xfs_trans_alloc(mp, XFS_TRANS_STRAT_WRITE);
tp->t_flags |= XFS_TRANS_RESERVE;
nres = XFS_EXTENTADD_SPACE_RES(mp, XFS_DATA_FORK);
error = xfs_trans_reserve(tp, nres,
XFS_WRITE_LOG_RES(mp),
0, XFS_TRANS_PERM_LOG_RES,
XFS_WRITE_LOG_COUNT);
if (error) {
xfs_trans_cancel(tp, 0);
return XFS_ERROR(error);
}
xfs_ilock(ip, XFS_ILOCK_EXCL);
xfs_trans_ijoin(tp, ip, 0);
xfs_bmap_init(&free_list, &first_block);
/*
* it is possible that the extents have changed since
* we did the read call as we dropped the ilock for a
* while. We have to be careful about truncates or hole
* punchs here - we are not allowed to allocate
* non-delalloc blocks here.
*
* The only protection against truncation is the pages
* for the range we are being asked to convert are
* locked and hence a truncate will block on them
* first.
*
* As a result, if we go beyond the range we really
* need and hit an delalloc extent boundary followed by
* a hole while we have excess blocks in the map, we
* will fill the hole incorrectly and overrun the
* transaction reservation.
*
* Using a single map prevents this as we are forced to
* check each map we look for overlap with the desired
* range and abort as soon as we find it. Also, given
* that we only return a single map, having one beyond
* what we can return is probably a bit silly.
*
* We also need to check that we don't go beyond EOF;
* this is a truncate optimisation as a truncate sets
* the new file size before block on the pages we
* currently have locked under writeback. Because they
* are about to be tossed, we don't need to write them
* back....
*/
nimaps = 1;
end_fsb = XFS_B_TO_FSB(mp, XFS_ISIZE(ip));
error = xfs_bmap_last_offset(NULL, ip, &last_block,
XFS_DATA_FORK);
if (error)
goto trans_cancel;
last_block = XFS_FILEOFF_MAX(last_block, end_fsb);
if ((map_start_fsb + count_fsb) > last_block) {
count_fsb = last_block - map_start_fsb;
if (count_fsb == 0) {
error = EAGAIN;
goto trans_cancel;
}
}
/*
* From this point onwards we overwrite the imap
* pointer that the caller gave to us.
*/
error = xfs_bmapi_write(tp, ip, map_start_fsb,
count_fsb,
XFS_BMAPI_STACK_SWITCH,
&first_block, 1,
imap, &nimaps, &free_list);
if (error)
goto trans_cancel;
error = xfs_bmap_finish(&tp, &free_list, &committed);
if (error)
goto trans_cancel;
error = xfs_trans_commit(tp, XFS_TRANS_RELEASE_LOG_RES);
if (error)
goto error0;
xfs_iunlock(ip, XFS_ILOCK_EXCL);
}
/*
* See if we were able to allocate an extent that
* covers at least part of the callers request
*/
if (!(imap->br_startblock || XFS_IS_REALTIME_INODE(ip)))
return xfs_alert_fsblock_zero(ip, imap);
if ((offset_fsb >= imap->br_startoff) &&
(offset_fsb < (imap->br_startoff +
imap->br_blockcount))) {
XFS_STATS_INC(xs_xstrat_quick);
return 0;
}
/*
* So far we have not mapped the requested part of the
* file, just surrounding data, try again.
*/
count_fsb -= imap->br_blockcount;
map_start_fsb = imap->br_startoff + imap->br_blockcount;
}
trans_cancel:
xfs_bmap_cancel(&free_list);
xfs_trans_cancel(tp, XFS_TRANS_RELEASE_LOG_RES | XFS_TRANS_ABORT);
error0:
xfs_iunlock(ip, XFS_ILOCK_EXCL);
return XFS_ERROR(error);
}
int
xfs_iomap_write_unwritten(
xfs_inode_t *ip,
xfs_off_t offset,
size_t count)
{
xfs_mount_t *mp = ip->i_mount;
xfs_fileoff_t offset_fsb;
xfs_filblks_t count_fsb;
xfs_filblks_t numblks_fsb;
xfs_fsblock_t firstfsb;
int nimaps;
xfs_trans_t *tp;
xfs_bmbt_irec_t imap;
xfs_bmap_free_t free_list;
xfs_fsize_t i_size;
uint resblks;
int committed;
int error;
xfs: event tracing support Convert the old xfs tracing support that could only be used with the out of tree kdb and xfsidbg patches to use the generic event tracer. To use it make sure CONFIG_EVENT_TRACING is enabled and then enable all xfs trace channels by: echo 1 > /sys/kernel/debug/tracing/events/xfs/enable or alternatively enable single events by just doing the same in one event subdirectory, e.g. echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable or set more complex filters, etc. In Documentation/trace/events.txt all this is desctribed in more detail. To reads the events do a cat /sys/kernel/debug/tracing/trace Compared to the last posting this patch converts the tracing mostly to the one tracepoint per callsite model that other users of the new tracing facility also employ. This allows a very fine-grained control of the tracing, a cleaner output of the traces and also enables the perf tool to use each tracepoint as a virtual performance counter, allowing us to e.g. count how often certain workloads git various spots in XFS. Take a look at http://lwn.net/Articles/346470/ for some examples. Also the btree tracing isn't included at all yet, as it will require additional core tracing features not in mainline yet, I plan to deliver it later. And the really nice thing about this patch is that it actually removes many lines of code while adding this nice functionality: fs/xfs/Makefile | 8 fs/xfs/linux-2.6/xfs_acl.c | 1 fs/xfs/linux-2.6/xfs_aops.c | 52 - fs/xfs/linux-2.6/xfs_aops.h | 2 fs/xfs/linux-2.6/xfs_buf.c | 117 +-- fs/xfs/linux-2.6/xfs_buf.h | 33 fs/xfs/linux-2.6/xfs_fs_subr.c | 3 fs/xfs/linux-2.6/xfs_ioctl.c | 1 fs/xfs/linux-2.6/xfs_ioctl32.c | 1 fs/xfs/linux-2.6/xfs_iops.c | 1 fs/xfs/linux-2.6/xfs_linux.h | 1 fs/xfs/linux-2.6/xfs_lrw.c | 87 -- fs/xfs/linux-2.6/xfs_lrw.h | 45 - fs/xfs/linux-2.6/xfs_super.c | 104 --- fs/xfs/linux-2.6/xfs_super.h | 7 fs/xfs/linux-2.6/xfs_sync.c | 1 fs/xfs/linux-2.6/xfs_trace.c | 75 ++ fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++ fs/xfs/linux-2.6/xfs_vnode.h | 4 fs/xfs/quota/xfs_dquot.c | 110 --- fs/xfs/quota/xfs_dquot.h | 21 fs/xfs/quota/xfs_qm.c | 40 - fs/xfs/quota/xfs_qm_syscalls.c | 4 fs/xfs/support/ktrace.c | 323 --------- fs/xfs/support/ktrace.h | 85 -- fs/xfs/xfs.h | 16 fs/xfs/xfs_ag.h | 14 fs/xfs/xfs_alloc.c | 230 +----- fs/xfs/xfs_alloc.h | 27 fs/xfs/xfs_alloc_btree.c | 1 fs/xfs/xfs_attr.c | 107 --- fs/xfs/xfs_attr.h | 10 fs/xfs/xfs_attr_leaf.c | 14 fs/xfs/xfs_attr_sf.h | 40 - fs/xfs/xfs_bmap.c | 507 +++------------ fs/xfs/xfs_bmap.h | 49 - fs/xfs/xfs_bmap_btree.c | 6 fs/xfs/xfs_btree.c | 5 fs/xfs/xfs_btree_trace.h | 17 fs/xfs/xfs_buf_item.c | 87 -- fs/xfs/xfs_buf_item.h | 20 fs/xfs/xfs_da_btree.c | 3 fs/xfs/xfs_da_btree.h | 7 fs/xfs/xfs_dfrag.c | 2 fs/xfs/xfs_dir2.c | 8 fs/xfs/xfs_dir2_block.c | 20 fs/xfs/xfs_dir2_leaf.c | 21 fs/xfs/xfs_dir2_node.c | 27 fs/xfs/xfs_dir2_sf.c | 26 fs/xfs/xfs_dir2_trace.c | 216 ------ fs/xfs/xfs_dir2_trace.h | 72 -- fs/xfs/xfs_filestream.c | 8 fs/xfs/xfs_fsops.c | 2 fs/xfs/xfs_iget.c | 111 --- fs/xfs/xfs_inode.c | 67 -- fs/xfs/xfs_inode.h | 76 -- fs/xfs/xfs_inode_item.c | 5 fs/xfs/xfs_iomap.c | 85 -- fs/xfs/xfs_iomap.h | 8 fs/xfs/xfs_log.c | 181 +---- fs/xfs/xfs_log_priv.h | 20 fs/xfs/xfs_log_recover.c | 1 fs/xfs/xfs_mount.c | 2 fs/xfs/xfs_quota.h | 8 fs/xfs/xfs_rename.c | 1 fs/xfs/xfs_rtalloc.c | 1 fs/xfs/xfs_rw.c | 3 fs/xfs/xfs_trans.h | 47 + fs/xfs/xfs_trans_buf.c | 62 - fs/xfs/xfs_vnodeops.c | 8 70 files changed, 2151 insertions(+), 2592 deletions(-) Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com>
2009-12-15 02:14:59 +03:00
trace_xfs_unwritten_convert(ip, offset, count);
offset_fsb = XFS_B_TO_FSBT(mp, offset);
count_fsb = XFS_B_TO_FSB(mp, (xfs_ufsize_t)offset + count);
count_fsb = (xfs_filblks_t)(count_fsb - offset_fsb);
/*
* Reserve enough blocks in this transaction for two complete extent
* btree splits. We may be converting the middle part of an unwritten
* extent and in this case we will insert two new extents in the btree
* each of which could cause a full split.
*
* This reservation amount will be used in the first call to
* xfs_bmbt_split() to select an AG with enough space to satisfy the
* rest of the operation.
*/
resblks = XFS_DIOSTRAT_SPACE_RES(mp, 0) << 1;
do {
/*
* set up a transaction to convert the range of extents
* from unwritten to real. Do allocations in a loop until
* we have covered the range passed in.
*
* Note that we open code the transaction allocation here
* to pass KM_NOFS--we can't risk to recursing back into
* the filesystem here as we might be asked to write out
* the same inode that we complete here and might deadlock
* on the iolock.
*/
sb_start_intwrite(mp->m_super);
tp = _xfs_trans_alloc(mp, XFS_TRANS_STRAT_WRITE, KM_NOFS);
tp->t_flags |= XFS_TRANS_RESERVE | XFS_TRANS_FREEZE_PROT;
error = xfs_trans_reserve(tp, resblks,
XFS_WRITE_LOG_RES(mp), 0,
XFS_TRANS_PERM_LOG_RES,
XFS_WRITE_LOG_COUNT);
if (error) {
xfs_trans_cancel(tp, 0);
return XFS_ERROR(error);
}
xfs_ilock(ip, XFS_ILOCK_EXCL);
xfs_trans_ijoin(tp, ip, 0);
/*
* Modify the unwritten extent state of the buffer.
*/
xfs_bmap_init(&free_list, &firstfsb);
nimaps = 1;
error = xfs_bmapi_write(tp, ip, offset_fsb, count_fsb,
XFS_BMAPI_CONVERT, &firstfsb,
1, &imap, &nimaps, &free_list);
if (error)
goto error_on_bmapi_transaction;
/*
* Log the updated inode size as we go. We have to be careful
* to only log it up to the actual write offset if it is
* halfway into a block.
*/
i_size = XFS_FSB_TO_B(mp, offset_fsb + count_fsb);
if (i_size > offset + count)
i_size = offset + count;
i_size = xfs_new_eof(ip, i_size);
if (i_size) {
ip->i_d.di_size = i_size;
xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
}
error = xfs_bmap_finish(&tp, &free_list, &committed);
if (error)
goto error_on_bmapi_transaction;
error = xfs_trans_commit(tp, XFS_TRANS_RELEASE_LOG_RES);
xfs_iunlock(ip, XFS_ILOCK_EXCL);
if (error)
return XFS_ERROR(error);
if (!(imap.br_startblock || XFS_IS_REALTIME_INODE(ip)))
return xfs_alert_fsblock_zero(ip, &imap);
if ((numblks_fsb = imap.br_blockcount) == 0) {
/*
* The numblks_fsb value should always get
* smaller, otherwise the loop is stuck.
*/
ASSERT(imap.br_blockcount);
break;
}
offset_fsb += numblks_fsb;
count_fsb -= numblks_fsb;
} while (count_fsb > 0);
return 0;
error_on_bmapi_transaction:
xfs_bmap_cancel(&free_list);
xfs_trans_cancel(tp, (XFS_TRANS_RELEASE_LOG_RES | XFS_TRANS_ABORT));
xfs_iunlock(ip, XFS_ILOCK_EXCL);
return XFS_ERROR(error);
}