WSL2-Linux-Kernel/arch/arm/mach-omap2/board-am3517crane.c

/*
 * Support for AM3517/05 Craneboard
 * http://www.mistralsolutions.com/products/craneboard.php
 *
 * Copyright (C) 2010 Mistral Solutions Pvt Ltd. <www.mistralsolutions.com>
 * Author: R.Srinath <srinath@mistralsolutions.com>
 *
 * Based on mach-omap2/board-am3517evm.c
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as  published by the
 * Free Software Foundation version 2.
 *
 * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
 * whether express or implied; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/gpio.h>

#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>

#include <plat/board.h>
#include <plat/common.h>
#include <plat/usb.h>

#include "mux.h"
#include "control.h"

#define GPIO_USB_POWER		35
#define GPIO_USB_NRESET		38


/* Board initialization */
static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif

static void __init am3517_crane_init_early(void)
{
	omap2_init_common_infrastructure();
}

static struct usbhs_omap_board_data usbhs_bdata __initdata = {
	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,

	.phy_reset  = true,
	.reset_gpio_port[0]  = GPIO_USB_NRESET,
	.reset_gpio_port[1]  = -EINVAL,
	.reset_gpio_port[2]  = -EINVAL
};

static void __init am3517_crane_init(void)
{
	int ret;

	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
	omap_serial_init();
	omap_sdrc_init(NULL, NULL);

	omap_board_config = am3517_crane_config;
	omap_board_config_size = ARRAY_SIZE(am3517_crane_config);

	/* Configure GPIO for EHCI port */
	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
		pr_err("Can not configure mux for GPIO_USB_NRESET %d\n",
			GPIO_USB_NRESET);
		return;
	}

	if (omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT)) {
		pr_err("Can not configure mux for GPIO_USB_POWER %d\n",
			GPIO_USB_POWER);
		return;
	}

	ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
			       "usb_ehci_enable");
	if (ret < 0) {
		pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
		return;
	}

	usbhs_init(&usbhs_bdata);
}

MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
	.boot_params	= 0x80000100,
	.reserve	= omap_reserve,
	.map_io		= omap3_map_io,
	.init_early	= am3517_crane_init_early,
	.init_irq	= omap3_init_irq,
	.init_machine	= am3517_crane_init,
	.timer		= &omap3_timer,
MACHINE_END