WSL2-Linux-Kernel/arch/powerpc/kernel/Makefile

91 строка
2.8 KiB
Makefile
Исходник Обычный вид История

#
# Makefile for the linux kernel.
#
ifeq ($(CONFIG_PPC64),y)
EXTRA_CFLAGS += -mno-minimal-toc
endif
ifeq ($(CONFIG_PPC32),y)
CFLAGS_prom_init.o += -fPIC
CFLAGS_btext.o += -fPIC
endif
obj-y := semaphore.o cputable.o ptrace.o syscalls.o \
irq.o align.o signal_32.o pmc.o vdso.o \
init_task.o process.o systbl.o idle.o \
signal.o
obj-y += vdso32/
obj-$(CONFIG_PPC64) += setup_64.o binfmt_elf32.o sys_ppc32.o \
signal_64.o ptrace32.o \
paca.o cpu_setup_ppc970.o \
cpu_setup_pa6t.o \
firmware.o sysfs.o nvram_64.o
obj-$(CONFIG_PPC64) += vdso64/
obj-$(CONFIG_ALTIVEC) += vecemu.o vector.o
obj-$(CONFIG_PPC_970_NAP) += idle_power4.o
obj-$(CONFIG_PPC_OF) += of_device.o of_platform.o prom_parse.o
obj-$(CONFIG_PPC_CLOCK) += clock.o
procfs-$(CONFIG_PPC64) := proc_ppc64.o
obj-$(CONFIG_PROC_FS) += $(procfs-y)
rtaspci-$(CONFIG_PPC64)-$(CONFIG_PCI) := rtas_pci.o
obj-$(CONFIG_PPC_RTAS) += rtas.o rtas-rtc.o $(rtaspci-y-y)
obj-$(CONFIG_RTAS_FLASH) += rtas_flash.o
obj-$(CONFIG_RTAS_PROC) += rtas-proc.o
obj-$(CONFIG_LPARCFG) += lparcfg.o
obj-$(CONFIG_IBMVIO) += vio.o
obj-$(CONFIG_IBMEBUS) += ibmebus.o
obj-$(CONFIG_GENERIC_TBSYNC) += smp-tbsync.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
obj-$(CONFIG_6xx) += idle_6xx.o l2cr_6xx.o cpu_setup_6xx.o
obj-$(CONFIG_TAU) += tau_6xx.o
obj-$(CONFIG_HIBERNATION) += swsusp.o suspend.o \
swsusp_$(CONFIG_WORD_SIZE).o
obj64-$(CONFIG_HIBERNATION) += swsusp_asm64.o
obj-$(CONFIG_MODULES) += module_$(CONFIG_WORD_SIZE).o
ifeq ($(CONFIG_PPC_MERGE),y)
extra-$(CONFIG_PPC_STD_MMU) := head_32.o
extra-$(CONFIG_PPC64) := head_64.o
extra-$(CONFIG_40x) := head_40x.o
extra-$(CONFIG_44x) := head_44x.o
extra-$(CONFIG_FSL_BOOKE) := head_fsl_booke.o
extra-$(CONFIG_8xx) := head_8xx.o
extra-y += vmlinux.lds
obj-y += time.o prom.o traps.o setup-common.o \
udbg.o misc.o io.o \
misc_$(CONFIG_WORD_SIZE).o
obj-$(CONFIG_PPC32) += entry_32.o setup_32.o
obj-$(CONFIG_PPC64) += dma_64.o iommu.o
obj-$(CONFIG_PPC_MULTIPLATFORM) += prom_init.o
obj-$(CONFIG_MODULES) += ppc_ksyms.o
obj-$(CONFIG_BOOTX_TEXT) += btext.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_KPROBES) += kprobes.o
obj-$(CONFIG_PPC_UDBG_16550) += legacy_serial.o udbg_16550.o
pci64-$(CONFIG_PPC64) += pci_dn.o isa-bridge.o
obj-$(CONFIG_PCI) += pci_$(CONFIG_WORD_SIZE).o $(pci64-y) \
pci-common.o
obj-$(CONFIG_PCI_MSI) += msi.o
obj-$(CONFIG_KEXEC) += machine_kexec.o crash.o \
machine_kexec_$(CONFIG_WORD_SIZE).o
obj-$(CONFIG_AUDIT) += audit.o
obj64-$(CONFIG_AUDIT) += compat_audit.o
[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits This patch reworks the way iSeries hooks on PCI IO operations (both MMIO and PIO) and provides a generic way for other platforms to do so (we have need to do that for various other platforms). While reworking the IO ops, I ended up doing some spring cleaning in io.h and eeh.h which I might want to split into 2 or 3 patches (among others, eeh.h had a lot of useless stuff in it). A side effect is that EEH for PIO should work now (it used to pass IO ports down to the eeh address check functions which is bogus). Also, new are MMIO "repeat" ops, which other archs like ARM already had, and that we have too now: readsb, readsw, readsl, writesb, writesw, writesl. In the long run, I might also make EEH use the hooks instead of wrapping at the toplevel, which would make things even cleaner and relegate EEH completely in platforms/iseries, but we have to measure the performance impact there (though it's really only on MMIO reads) Since I also need to hook on ioremap, I shuffled the functions a bit there. I introduced ioremap_flags() to use by drivers who want to pass explicit flags to ioremap (and it can be hooked). The old __ioremap() is still there as a low level and cannot be hooked, thus drivers who use it should migrate unless they know they want the low level version. The patch "arch provides generic iomap missing accessors" (should be number 4 in this series) is a pre-requisite to provide full iomap API support with this patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-11 09:25:10 +03:00
ifneq ($(CONFIG_PPC_INDIRECT_IO),y)
obj-y += iomap.o
[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits This patch reworks the way iSeries hooks on PCI IO operations (both MMIO and PIO) and provides a generic way for other platforms to do so (we have need to do that for various other platforms). While reworking the IO ops, I ended up doing some spring cleaning in io.h and eeh.h which I might want to split into 2 or 3 patches (among others, eeh.h had a lot of useless stuff in it). A side effect is that EEH for PIO should work now (it used to pass IO ports down to the eeh address check functions which is bogus). Also, new are MMIO "repeat" ops, which other archs like ARM already had, and that we have too now: readsb, readsw, readsl, writesb, writesw, writesl. In the long run, I might also make EEH use the hooks instead of wrapping at the toplevel, which would make things even cleaner and relegate EEH completely in platforms/iseries, but we have to measure the performance impact there (though it's really only on MMIO reads) Since I also need to hook on ioremap, I shuffled the functions a bit there. I introduced ioremap_flags() to use by drivers who want to pass explicit flags to ioremap (and it can be hooked). The old __ioremap() is still there as a low level and cannot be hooked, thus drivers who use it should migrate unless they know they want the low level version. The patch "arch provides generic iomap missing accessors" (should be number 4 in this series) is a pre-requisite to provide full iomap API support with this patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-11 09:25:10 +03:00
endif
else
# stuff used from here for ARCH=ppc
smpobj-$(CONFIG_SMP) += smp.o
endif
[PATCH] powerpc: Fix handling of fpscr on 64-bit The recent merge of fpu.S broken the handling of fpscr for ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted, leading to strange random application crashes. The confusion arises, because the thread_struct has (and requires) a 64-bit area to save the fpscr, because we use load/store double instructions to get it in to/out of the FPU. However, only the low 32-bits are actually used, so we want to treat it as a 32-bit quantity when manipulating its bits to avoid extra load/stores on 32-bit. This patch replaces the current definition with a structure of two 32-bit quantities (pad and val), to clarify things as much as is possible. The 'val' field is used when manipulating bits, the structure itself is used when obtaining the address for loading/unloading the value from the FPU. While we're at it, consolidate the 4 (!) almost identical versions of cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S, arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S, arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The new version takes a pointer to thread_struct and applies the correct offset itself, rather than a pointer to the fpscr field itself, again to avoid confusion as to which is the correct field to use. Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S code, which it previously did not. Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y). Booted on G5 (ARCH=powerpc) and things which previously fell over no longer do. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-27 10:27:25 +04:00
obj-$(CONFIG_PPC64) += $(obj64-y)
[PATCH] powerpc: Fix handling of fpscr on 64-bit The recent merge of fpu.S broken the handling of fpscr for ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted, leading to strange random application crashes. The confusion arises, because the thread_struct has (and requires) a 64-bit area to save the fpscr, because we use load/store double instructions to get it in to/out of the FPU. However, only the low 32-bits are actually used, so we want to treat it as a 32-bit quantity when manipulating its bits to avoid extra load/stores on 32-bit. This patch replaces the current definition with a structure of two 32-bit quantities (pad and val), to clarify things as much as is possible. The 'val' field is used when manipulating bits, the structure itself is used when obtaining the address for loading/unloading the value from the FPU. While we're at it, consolidate the 4 (!) almost identical versions of cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S, arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S, arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The new version takes a pointer to thread_struct and applies the correct offset itself, rather than a pointer to the fpscr field itself, again to avoid confusion as to which is the correct field to use. Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S code, which it previously did not. Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y). Booted on G5 (ARCH=powerpc) and things which previously fell over no longer do. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-27 10:27:25 +04:00
extra-$(CONFIG_PPC_FPU) += fpu.o
extra-$(CONFIG_PPC64) += entry_64.o