microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/sound/soc/codecs/wm_hubs.h

42 строки
1.0 KiB
C
Исходник Обычный вид История

ASoC: Factor out shared code from WM8993 The WM8993 analogue control is shared with other devices in the same product line. Since this is a very substantial proportion of the driver move the definitions of these controls into a new wm_hubs module which allows them to be shared between the two. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-07-30 00:21:49 +04:00
/*
* wm_hubs.h -- WM899x common code
*
* Copyright 2009 Wolfson Microelectronics plc
*
* Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef _WM_HUBS_H
#define _WM_HUBS_H
struct snd_soc_codec;
extern const unsigned int wm_hubs_spkmix_tlv[];
ASoC: Improved wm_hubs headphone handling Perform DC servo offset calibration using a series update sequence rather than startup update sequence, tuning the configuration of the WM8993 DC servo to make best use of this. Also introduce currently unused data allowing us to correct for any systematic errors in the DC servo calibration results and an alternative startup path for the headphone output which performs better with some chip revisions. The alternative setup sequence is enabled for WM8993. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-01-20 20:39:45 +03:00
/* This *must* be the first element of the codec->private_data struct */
struct wm_hubs_data {
int dcs_codes;
ASoC: Support second DC servo readback method for wm_hubs More recent Wolfson hubs devices add the ability to read back the DC servo calibration information from the register used to write offsets, and later still ones remove the old readback registers. Add support for the new scheme, and use it for WM8994 device revisions that support it. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-29 20:09:45 +04:00
int dcs_readback_mode;
ASoC: Improved wm_hubs headphone handling Perform DC servo offset calibration using a series update sequence rather than startup update sequence, tuning the configuration of the WM8993 DC servo to make best use of this. Also introduce currently unused data allowing us to correct for any systematic errors in the DC servo calibration results and an alternative startup path for the headphone output which performs better with some chip revisions. The alternative setup sequence is enabled for WM8993. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-01-20 20:39:45 +03:00
int hp_startup_mode;
ASoC: Trigger wm_hubs series update startup off a separate flag Allowing the two to be used independently. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
2011-06-08 02:23:52 +04:00
int series_startup;
ASoC: Allow suppression of series updates on wm_hubs devices Some devices do not support manual updates of the DC servo. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
2011-06-08 02:32:46 +04:00
int no_series_update;
ASoC: Store DC offset correction for wm_hubs devices in class W mode Providing the analogue configuration of the output path remains the same the DC offset corrected by the DC servo will remain identical so we can skip the callibration, reducing the startup time for the headphone output. Implement this for the wm_hubs devices as has been done for several other CODECs. Don't do this if we have any analogue paths enabled since offsets may be being introduced by the analogue paths which could vary outside the control of the driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-10-28 00:48:36 +04:00
bool class_w;
u16 class_w_dcs;
ASoC: Improved wm_hubs headphone handling Perform DC servo offset calibration using a series update sequence rather than startup update sequence, tuning the configuration of the WM8993 DC servo to make best use of this. Also introduce currently unused data allowing us to correct for any systematic errors in the DC servo calibration results and an alternative startup path for the headphone output which performs better with some chip revisions. The alternative setup sequence is enabled for WM8993. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-01-20 20:39:45 +03:00
};
ASoC: Factor out shared code from WM8993 The WM8993 analogue control is shared with other devices in the same product line. Since this is a very substantial proportion of the driver move the definitions of these controls into a new wm_hubs module which allows them to be shared between the two. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-07-30 00:21:49 +04:00
extern int wm_hubs_add_analogue_controls(struct snd_soc_codec *);
extern int wm_hubs_add_analogue_routes(struct snd_soc_codec *, int, int);
ASoC: Factor out analogue platform data from WM8993 This is also shared with newer CODECs. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-30 17:16:11 +04:00
extern int wm_hubs_handle_analogue_pdata(struct snd_soc_codec *,
int lineout1_diff, int lineout2_diff,
int lineout1fb, int lineout2fb,
int jd_scthr, int jd_thr,
int micbias1_lvl, int micbias2_lvl);
ASoC: Factor out shared code from WM8993 The WM8993 analogue control is shared with other devices in the same product line. Since this is a very substantial proportion of the driver move the definitions of these controls into a new wm_hubs module which allows them to be shared between the two. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-07-30 00:21:49 +04:00
#endif