microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/arch/powerpc/lib/copyuser_power7.S

710 строки
13 KiB
ArmAsm
Исходник Обычный вид История

powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*
* Copyright (C) IBM Corporation, 2011
*
* Author: Anton Blanchard <anton@au.ibm.com>
*/
#include <asm/ppc_asm.h>
powerpc: Fix endian issues in VMX copy loops Fix the permute loops for little endian. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-09-23 06:04:35 +04:00
#ifdef __BIG_ENDIAN__
#define LVS(VRT,RA,RB) lvsl VRT,RA,RB
#define VPERM(VRT,VRA,VRB,VRC) vperm VRT,VRA,VRB,VRC
#else
#define LVS(VRT,RA,RB) lvsr VRT,RA,RB
#define VPERM(VRT,VRA,VRB,VRC) vperm VRT,VRB,VRA,VRC
#endif
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.macro err1
100:
powerpc: EX_TABLE macro for exception tables This macro is taken from s390, and allows more flexibility in changing exception table format. mpe: Put it in ppc_asm.h and only define one version using stringinfy_in_c(). Add some empty definitions and headers to keep the selftests happy. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-10-13 08:42:53 +03:00
EX_TABLE(100b,.Ldo_err1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.endm
.macro err2
200:
powerpc: EX_TABLE macro for exception tables This macro is taken from s390, and allows more flexibility in changing exception table format. mpe: Put it in ppc_asm.h and only define one version using stringinfy_in_c(). Add some empty definitions and headers to keep the selftests happy. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-10-13 08:42:53 +03:00
EX_TABLE(200b,.Ldo_err2)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.endm
#ifdef CONFIG_ALTIVEC
.macro err3
300:
powerpc: EX_TABLE macro for exception tables This macro is taken from s390, and allows more flexibility in changing exception table format. mpe: Put it in ppc_asm.h and only define one version using stringinfy_in_c(). Add some empty definitions and headers to keep the selftests happy. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-10-13 08:42:53 +03:00
EX_TABLE(300b,.Ldo_err3)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.endm
.macro err4
400:
powerpc: EX_TABLE macro for exception tables This macro is taken from s390, and allows more flexibility in changing exception table format. mpe: Put it in ppc_asm.h and only define one version using stringinfy_in_c(). Add some empty definitions and headers to keep the selftests happy. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-10-13 08:42:53 +03:00
EX_TABLE(400b,.Ldo_err4)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.endm
.Ldo_err4:
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
ld r16,STK_REG(R16)(r1)
ld r15,STK_REG(R15)(r1)
ld r14,STK_REG(R14)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.Ldo_err3:
powerpc: No need to use dot symbols when branching to a function binutils is smart enough to know that a branch to a function descriptor is actually a branch to the functions text address. Alan tells me that binutils has been doing this for 9 years. Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-04 09:04:35 +04:00
bl exit_vmx_usercopy
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
ld r0,STACKFRAMESIZE+16(r1)
mtlr r0
b .Lexit
#endif /* CONFIG_ALTIVEC */
.Ldo_err2:
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
ld r22,STK_REG(R22)(r1)
ld r21,STK_REG(R21)(r1)
ld r20,STK_REG(R20)(r1)
ld r19,STK_REG(R19)(r1)
ld r18,STK_REG(R18)(r1)
ld r17,STK_REG(R17)(r1)
ld r16,STK_REG(R16)(r1)
ld r15,STK_REG(R15)(r1)
ld r14,STK_REG(R14)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.Lexit:
addi r1,r1,STACKFRAMESIZE
.Ldo_err1:
powerpc: Fix unsafe accesses to parameter area in ELFv2 Some of the assembler files in lib/ make use of the fact that in the ELFv1 ABI, the caller guarantees to provide stack space to save the parameter registers r3 ... r10. This guarantee is no longer present in ELFv2 for functions that have no variable argument list and no more than 8 arguments. Change the affected routines to temporarily store registers in the red zone and/or the top of their own stack frame (in the space provided to save r31 .. r29, which is actually not used in these routines). In opal_query_takeover, simply always allocate a stack frame; the routine is not performance critical. Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-14 22:21:03 +04:00
ld r3,-STACKFRAMESIZE+STK_REG(R31)(r1)
ld r4,-STACKFRAMESIZE+STK_REG(R30)(r1)
ld r5,-STACKFRAMESIZE+STK_REG(R29)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
b __copy_tofrom_user_base
_GLOBAL(__copy_tofrom_user_power7)
#ifdef CONFIG_ALTIVEC
cmpldi r5,16
powerpc: Tweak copy selection parameter in __copy_tofrom_user_power7() Experiments with the netperf benchmark indicated that the size selecting VMX-based copies in __copy_tofrom_user_power7() was suboptimal on POWER8. Measurements showed that parity was in the neighbourhood of 3328 bytes, rather than greater than 4096. The change gives a 1.5-2.0% improvement in performance for 4096-byte buffers, reducing the relative time spent in __copy_tofrom_user_power7() from approximately 7% to approximately 5% in the TCP_RR benchmark. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-05-12 06:58:10 +03:00
cmpldi cr1,r5,3328
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
powerpc: Fix unsafe accesses to parameter area in ELFv2 Some of the assembler files in lib/ make use of the fact that in the ELFv1 ABI, the caller guarantees to provide stack space to save the parameter registers r3 ... r10. This guarantee is no longer present in ELFv2 for functions that have no variable argument list and no more than 8 arguments. Change the affected routines to temporarily store registers in the red zone and/or the top of their own stack frame (in the space provided to save r31 .. r29, which is actually not used in these routines). In opal_query_takeover, simply always allocate a stack frame; the routine is not performance critical. Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-14 22:21:03 +04:00
std r3,-STACKFRAMESIZE+STK_REG(R31)(r1)
std r4,-STACKFRAMESIZE+STK_REG(R30)(r1)
std r5,-STACKFRAMESIZE+STK_REG(R29)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
blt .Lshort_copy
powerpc: Tweak copy selection parameter in __copy_tofrom_user_power7() Experiments with the netperf benchmark indicated that the size selecting VMX-based copies in __copy_tofrom_user_power7() was suboptimal on POWER8. Measurements showed that parity was in the neighbourhood of 3328 bytes, rather than greater than 4096. The change gives a 1.5-2.0% improvement in performance for 4096-byte buffers, reducing the relative time spent in __copy_tofrom_user_power7() from approximately 7% to approximately 5% in the TCP_RR benchmark. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-05-12 06:58:10 +03:00
bge cr1,.Lvmx_copy
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
#else
cmpldi r5,16
powerpc: Fix unsafe accesses to parameter area in ELFv2 Some of the assembler files in lib/ make use of the fact that in the ELFv1 ABI, the caller guarantees to provide stack space to save the parameter registers r3 ... r10. This guarantee is no longer present in ELFv2 for functions that have no variable argument list and no more than 8 arguments. Change the affected routines to temporarily store registers in the red zone and/or the top of their own stack frame (in the space provided to save r31 .. r29, which is actually not used in these routines). In opal_query_takeover, simply always allocate a stack frame; the routine is not performance critical. Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-14 22:21:03 +04:00
std r3,-STACKFRAMESIZE+STK_REG(R31)(r1)
std r4,-STACKFRAMESIZE+STK_REG(R30)(r1)
std r5,-STACKFRAMESIZE+STK_REG(R29)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
blt .Lshort_copy
#endif
.Lnonvmx_copy:
/* Get the source 8B aligned */
neg r6,r4
mtocrf 0x01,r6
clrldi r6,r6,(64-3)
bf cr7*4+3,1f
err1; lbz r0,0(r4)
addi r4,r4,1
err1; stb r0,0(r3)
addi r3,r3,1
1: bf cr7*4+2,2f
err1; lhz r0,0(r4)
addi r4,r4,2
err1; sth r0,0(r3)
addi r3,r3,2
2: bf cr7*4+1,3f
err1; lwz r0,0(r4)
addi r4,r4,4
err1; stw r0,0(r3)
addi r3,r3,4
3: sub r5,r5,r6
cmpldi r5,128
blt 5f
mflr r0
stdu r1,-STACKFRAMESIZE(r1)
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
std r14,STK_REG(R14)(r1)
std r15,STK_REG(R15)(r1)
std r16,STK_REG(R16)(r1)
std r17,STK_REG(R17)(r1)
std r18,STK_REG(R18)(r1)
std r19,STK_REG(R19)(r1)
std r20,STK_REG(R20)(r1)
std r21,STK_REG(R21)(r1)
std r22,STK_REG(R22)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
std r0,STACKFRAMESIZE+16(r1)
srdi r6,r5,7
mtctr r6
/* Now do cacheline (128B) sized loads and stores. */
.align 5
4:
err2; ld r0,0(r4)
err2; ld r6,8(r4)
err2; ld r7,16(r4)
err2; ld r8,24(r4)
err2; ld r9,32(r4)
err2; ld r10,40(r4)
err2; ld r11,48(r4)
err2; ld r12,56(r4)
err2; ld r14,64(r4)
err2; ld r15,72(r4)
err2; ld r16,80(r4)
err2; ld r17,88(r4)
err2; ld r18,96(r4)
err2; ld r19,104(r4)
err2; ld r20,112(r4)
err2; ld r21,120(r4)
addi r4,r4,128
err2; std r0,0(r3)
err2; std r6,8(r3)
err2; std r7,16(r3)
err2; std r8,24(r3)
err2; std r9,32(r3)
err2; std r10,40(r3)
err2; std r11,48(r3)
err2; std r12,56(r3)
err2; std r14,64(r3)
err2; std r15,72(r3)
err2; std r16,80(r3)
err2; std r17,88(r3)
err2; std r18,96(r3)
err2; std r19,104(r3)
err2; std r20,112(r3)
err2; std r21,120(r3)
addi r3,r3,128
bdnz 4b
clrldi r5,r5,(64-7)
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
ld r14,STK_REG(R14)(r1)
ld r15,STK_REG(R15)(r1)
ld r16,STK_REG(R16)(r1)
ld r17,STK_REG(R17)(r1)
ld r18,STK_REG(R18)(r1)
ld r19,STK_REG(R19)(r1)
ld r20,STK_REG(R20)(r1)
ld r21,STK_REG(R21)(r1)
ld r22,STK_REG(R22)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r1,r1,STACKFRAMESIZE
/* Up to 127B to go */
5: srdi r6,r5,4
mtocrf 0x01,r6
6: bf cr7*4+1,7f
err1; ld r0,0(r4)
err1; ld r6,8(r4)
err1; ld r7,16(r4)
err1; ld r8,24(r4)
err1; ld r9,32(r4)
err1; ld r10,40(r4)
err1; ld r11,48(r4)
err1; ld r12,56(r4)
addi r4,r4,64
err1; std r0,0(r3)
err1; std r6,8(r3)
err1; std r7,16(r3)
err1; std r8,24(r3)
err1; std r9,32(r3)
err1; std r10,40(r3)
err1; std r11,48(r3)
err1; std r12,56(r3)
addi r3,r3,64
/* Up to 63B to go */
7: bf cr7*4+2,8f
err1; ld r0,0(r4)
err1; ld r6,8(r4)
err1; ld r7,16(r4)
err1; ld r8,24(r4)
addi r4,r4,32
err1; std r0,0(r3)
err1; std r6,8(r3)
err1; std r7,16(r3)
err1; std r8,24(r3)
addi r3,r3,32
/* Up to 31B to go */
8: bf cr7*4+3,9f
err1; ld r0,0(r4)
err1; ld r6,8(r4)
addi r4,r4,16
err1; std r0,0(r3)
err1; std r6,8(r3)
addi r3,r3,16
9: clrldi r5,r5,(64-4)
/* Up to 15B to go */
.Lshort_copy:
mtocrf 0x01,r5
bf cr7*4+0,12f
err1; lwz r0,0(r4) /* Less chance of a reject with word ops */
err1; lwz r6,4(r4)
addi r4,r4,8
err1; stw r0,0(r3)
err1; stw r6,4(r3)
addi r3,r3,8
12: bf cr7*4+1,13f
err1; lwz r0,0(r4)
addi r4,r4,4
err1; stw r0,0(r3)
addi r3,r3,4
13: bf cr7*4+2,14f
err1; lhz r0,0(r4)
addi r4,r4,2
err1; sth r0,0(r3)
addi r3,r3,2
14: bf cr7*4+3,15f
err1; lbz r0,0(r4)
err1; stb r0,0(r3)
15: li r3,0
blr
.Lunwind_stack_nonvmx_copy:
addi r1,r1,STACKFRAMESIZE
b .Lnonvmx_copy
#ifdef CONFIG_ALTIVEC
.Lvmx_copy:
mflr r0
std r0,16(r1)
stdu r1,-STACKFRAMESIZE(r1)
powerpc: No need to use dot symbols when branching to a function binutils is smart enough to know that a branch to a function descriptor is actually a branch to the functions text address. Alan tells me that binutils has been doing this for 9 years. Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-04 09:04:35 +04:00
bl enter_vmx_usercopy
powerpc: Fix VMX in interrupt check in POWER7 copy loops The enhanced prefetch hint patches corrupt the condition register that was used to check if we are in interrupt. Fix this by using cr1. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-08-07 21:51:41 +04:00
cmpwi cr1,r3,0
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
ld r0,STACKFRAMESIZE+16(r1)
powerpc: Fix unsafe accesses to parameter area in ELFv2 Some of the assembler files in lib/ make use of the fact that in the ELFv1 ABI, the caller guarantees to provide stack space to save the parameter registers r3 ... r10. This guarantee is no longer present in ELFv2 for functions that have no variable argument list and no more than 8 arguments. Change the affected routines to temporarily store registers in the red zone and/or the top of their own stack frame (in the space provided to save r31 .. r29, which is actually not used in these routines). In opal_query_takeover, simply always allocate a stack frame; the routine is not performance critical. Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-14 22:21:03 +04:00
ld r3,STK_REG(R31)(r1)
ld r4,STK_REG(R30)(r1)
ld r5,STK_REG(R29)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
mtlr r0
powerpc: Use enhanced touch instructions in POWER7 copy_to_user/copy_from_user Version 2.06 of the POWER ISA introduced enhanced touch instructions, allowing us to specify a number of attributes including the length of a stream. This patch adds a software stream for both loads and stores in the POWER7 copy_tofrom_user loop. Since the setup is quite complicated and we have to use an eieio to ensure correct ordering of the "GO" command we only do this for copies above 4kB. To quantify any performance improvements we need a working set bigger than the caches so we operate on a 1GB file: # dd if=/dev/zero of=/tmp/foo bs=1M count=1024 And we compare how fast we can read the file: # dd if=/tmp/foo of=/dev/null bs=1M before: 7.7 GB/s after: 9.6 GB/s A 25% improvement. The worst case for this patch will be a completely L1 cache contained copy of just over 4kB. We can test this with the copy_to_user testcase we used to tune copy_tofrom_user originally: http://ozlabs.org/~anton/junkcode/copy_to_user.c # time ./copy_to_user2 -l 4224 -i 10000000 before: 6.807 s after: 6.946 s A 2% slowdown, which seems reasonable considering our data is unlikely to be completely L1 contained. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-05-29 02:14:32 +04:00
/*
* We prefetch both the source and destination using enhanced touch
* instructions. We use a stream ID of 0 for the load side and
* 1 for the store side.
*/
clrrdi r6,r4,7
clrrdi r9,r3,7
ori r9,r9,1 /* stream=1 */
srdi r7,r5,7 /* length in cachelines, capped at 0x3FF */
cmpldi r7,0x3FF
ble 1f
li r7,0x3FF
1: lis r0,0x0E00 /* depth=7 */
sldi r7,r7,7
or r7,r7,r0
ori r10,r7,1 /* stream=1 */
lis r8,0x8000 /* GO=1 */
clrldi r8,r8,32
.machine push
.machine "power4"
powerpc/pseries: Improve stream generation comments in copypage/user No code changes, just documenting what's happening a little better. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-05-29 23:34:29 +04:00
/* setup read stream 0 */
dcbt r0,r6,0b01000 /* addr from */
dcbt r0,r7,0b01010 /* length and depth from */
/* setup write stream 1 */
dcbtst r0,r9,0b01000 /* addr to */
dcbtst r0,r10,0b01010 /* length and depth to */
powerpc: Use enhanced touch instructions in POWER7 copy_to_user/copy_from_user Version 2.06 of the POWER ISA introduced enhanced touch instructions, allowing us to specify a number of attributes including the length of a stream. This patch adds a software stream for both loads and stores in the POWER7 copy_tofrom_user loop. Since the setup is quite complicated and we have to use an eieio to ensure correct ordering of the "GO" command we only do this for copies above 4kB. To quantify any performance improvements we need a working set bigger than the caches so we operate on a 1GB file: # dd if=/dev/zero of=/tmp/foo bs=1M count=1024 And we compare how fast we can read the file: # dd if=/tmp/foo of=/dev/null bs=1M before: 7.7 GB/s after: 9.6 GB/s A 25% improvement. The worst case for this patch will be a completely L1 cache contained copy of just over 4kB. We can test this with the copy_to_user testcase we used to tune copy_tofrom_user originally: http://ozlabs.org/~anton/junkcode/copy_to_user.c # time ./copy_to_user2 -l 4224 -i 10000000 before: 6.807 s after: 6.946 s A 2% slowdown, which seems reasonable considering our data is unlikely to be completely L1 contained. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-05-29 02:14:32 +04:00
eieio
powerpc/pseries: Improve stream generation comments in copypage/user No code changes, just documenting what's happening a little better. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-05-29 23:34:29 +04:00
dcbt r0,r8,0b01010 /* all streams GO */
powerpc: Use enhanced touch instructions in POWER7 copy_to_user/copy_from_user Version 2.06 of the POWER ISA introduced enhanced touch instructions, allowing us to specify a number of attributes including the length of a stream. This patch adds a software stream for both loads and stores in the POWER7 copy_tofrom_user loop. Since the setup is quite complicated and we have to use an eieio to ensure correct ordering of the "GO" command we only do this for copies above 4kB. To quantify any performance improvements we need a working set bigger than the caches so we operate on a 1GB file: # dd if=/dev/zero of=/tmp/foo bs=1M count=1024 And we compare how fast we can read the file: # dd if=/tmp/foo of=/dev/null bs=1M before: 7.7 GB/s after: 9.6 GB/s A 25% improvement. The worst case for this patch will be a completely L1 cache contained copy of just over 4kB. We can test this with the copy_to_user testcase we used to tune copy_tofrom_user originally: http://ozlabs.org/~anton/junkcode/copy_to_user.c # time ./copy_to_user2 -l 4224 -i 10000000 before: 6.807 s after: 6.946 s A 2% slowdown, which seems reasonable considering our data is unlikely to be completely L1 contained. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-05-29 02:14:32 +04:00
.machine pop
powerpc: Fix VMX in interrupt check in POWER7 copy loops The enhanced prefetch hint patches corrupt the condition register that was used to check if we are in interrupt. Fix this by using cr1. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-08-07 21:51:41 +04:00
beq cr1,.Lunwind_stack_nonvmx_copy
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
/*
* If source and destination are not relatively aligned we use a
* slower permute loop.
*/
xor r6,r4,r3
rldicl. r6,r6,0,(64-4)
bne .Lvmx_unaligned_copy
/* Get the destination 16B aligned */
neg r6,r3
mtocrf 0x01,r6
clrldi r6,r6,(64-4)
bf cr7*4+3,1f
err3; lbz r0,0(r4)
addi r4,r4,1
err3; stb r0,0(r3)
addi r3,r3,1
1: bf cr7*4+2,2f
err3; lhz r0,0(r4)
addi r4,r4,2
err3; sth r0,0(r3)
addi r3,r3,2
2: bf cr7*4+1,3f
err3; lwz r0,0(r4)
addi r4,r4,4
err3; stw r0,0(r3)
addi r3,r3,4
3: bf cr7*4+0,4f
err3; ld r0,0(r4)
addi r4,r4,8
err3; std r0,0(r3)
addi r3,r3,8
4: sub r5,r5,r6
/* Get the desination 128B aligned */
neg r6,r3
srdi r7,r6,4
mtocrf 0x01,r7
clrldi r6,r6,(64-7)
li r9,16
li r10,32
li r11,48
bf cr7*4+3,5f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,16
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v1,r0,r3
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,16
5: bf cr7*4+2,6f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
err3; lvx v0,r4,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,32
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v1,r0,r3
err3; stvx v0,r3,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,32
6: bf cr7*4+1,7f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v3,r0,r4
err3; lvx v2,r4,r9
err3; lvx v1,r4,r10
err3; lvx v0,r4,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,64
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v3,r0,r3
err3; stvx v2,r3,r9
err3; stvx v1,r3,r10
err3; stvx v0,r3,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,64
7: sub r5,r5,r6
srdi r6,r5,7
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
std r14,STK_REG(R14)(r1)
std r15,STK_REG(R15)(r1)
std r16,STK_REG(R16)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
li r12,64
li r14,80
li r15,96
li r16,112
mtctr r6
/*
* Now do cacheline sized loads and stores. By this stage the
* cacheline stores are also cacheline aligned.
*/
.align 5
8:
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err4; lvx v7,r0,r4
err4; lvx v6,r4,r9
err4; lvx v5,r4,r10
err4; lvx v4,r4,r11
err4; lvx v3,r4,r12
err4; lvx v2,r4,r14
err4; lvx v1,r4,r15
err4; lvx v0,r4,r16
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,128
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err4; stvx v7,r0,r3
err4; stvx v6,r3,r9
err4; stvx v5,r3,r10
err4; stvx v4,r3,r11
err4; stvx v3,r3,r12
err4; stvx v2,r3,r14
err4; stvx v1,r3,r15
err4; stvx v0,r3,r16
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,128
bdnz 8b
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
ld r14,STK_REG(R14)(r1)
ld r15,STK_REG(R15)(r1)
ld r16,STK_REG(R16)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
/* Up to 127B to go */
clrldi r5,r5,(64-7)
srdi r6,r5,4
mtocrf 0x01,r6
bf cr7*4+1,9f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v3,r0,r4
err3; lvx v2,r4,r9
err3; lvx v1,r4,r10
err3; lvx v0,r4,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,64
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v3,r0,r3
err3; stvx v2,r3,r9
err3; stvx v1,r3,r10
err3; stvx v0,r3,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,64
9: bf cr7*4+2,10f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
err3; lvx v0,r4,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,32
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v1,r0,r3
err3; stvx v0,r3,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,32
10: bf cr7*4+3,11f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,16
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v1,r0,r3
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,16
/* Up to 15B to go */
11: clrldi r5,r5,(64-4)
mtocrf 0x01,r5
bf cr7*4+0,12f
err3; ld r0,0(r4)
addi r4,r4,8
err3; std r0,0(r3)
addi r3,r3,8
12: bf cr7*4+1,13f
err3; lwz r0,0(r4)
addi r4,r4,4
err3; stw r0,0(r3)
addi r3,r3,4
13: bf cr7*4+2,14f
err3; lhz r0,0(r4)
addi r4,r4,2
err3; sth r0,0(r3)
addi r3,r3,2
14: bf cr7*4+3,15f
err3; lbz r0,0(r4)
err3; stb r0,0(r3)
15: addi r1,r1,STACKFRAMESIZE
powerpc: No need to use dot symbols when branching to a function binutils is smart enough to know that a branch to a function descriptor is actually a branch to the functions text address. Alan tells me that binutils has been doing this for 9 years. Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-04 09:04:35 +04:00
b exit_vmx_usercopy /* tail call optimise */
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
.Lvmx_unaligned_copy:
/* Get the destination 16B aligned */
neg r6,r3
mtocrf 0x01,r6
clrldi r6,r6,(64-4)
bf cr7*4+3,1f
err3; lbz r0,0(r4)
addi r4,r4,1
err3; stb r0,0(r3)
addi r3,r3,1
1: bf cr7*4+2,2f
err3; lhz r0,0(r4)
addi r4,r4,2
err3; sth r0,0(r3)
addi r3,r3,2
2: bf cr7*4+1,3f
err3; lwz r0,0(r4)
addi r4,r4,4
err3; stw r0,0(r3)
addi r3,r3,4
3: bf cr7*4+0,4f
err3; lwz r0,0(r4) /* Less chance of a reject with word ops */
err3; lwz r7,4(r4)
addi r4,r4,8
err3; stw r0,0(r3)
err3; stw r7,4(r3)
addi r3,r3,8
4: sub r5,r5,r6
/* Get the desination 128B aligned */
neg r6,r3
srdi r7,r6,4
mtocrf 0x01,r7
clrldi r6,r6,(64-7)
li r9,16
li r10,32
li r11,48
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
LVS(v16,0,r4) /* Setup permute control vector */
err3; lvx v0,0,r4
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,16
bf cr7*4+3,5f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
VPERM(v8,v0,v1,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,16
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,16
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
vor v0,v1,v1
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
5: bf cr7*4+2,6f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
VPERM(v8,v0,v1,v16)
err3; lvx v0,r4,r9
VPERM(v9,v1,v0,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,32
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
err3; stvx v9,r3,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,32
6: bf cr7*4+1,7f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v3,r0,r4
VPERM(v8,v0,v3,v16)
err3; lvx v2,r4,r9
VPERM(v9,v3,v2,v16)
err3; lvx v1,r4,r10
VPERM(v10,v2,v1,v16)
err3; lvx v0,r4,r11
VPERM(v11,v1,v0,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,64
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
err3; stvx v9,r3,r9
err3; stvx v10,r3,r10
err3; stvx v11,r3,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,64
7: sub r5,r5,r6
srdi r6,r5,7
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
std r14,STK_REG(R14)(r1)
std r15,STK_REG(R15)(r1)
std r16,STK_REG(R16)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
li r12,64
li r14,80
li r15,96
li r16,112
mtctr r6
/*
* Now do cacheline sized loads and stores. By this stage the
* cacheline stores are also cacheline aligned.
*/
.align 5
8:
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err4; lvx v7,r0,r4
VPERM(v8,v0,v7,v16)
err4; lvx v6,r4,r9
VPERM(v9,v7,v6,v16)
err4; lvx v5,r4,r10
VPERM(v10,v6,v5,v16)
err4; lvx v4,r4,r11
VPERM(v11,v5,v4,v16)
err4; lvx v3,r4,r12
VPERM(v12,v4,v3,v16)
err4; lvx v2,r4,r14
VPERM(v13,v3,v2,v16)
err4; lvx v1,r4,r15
VPERM(v14,v2,v1,v16)
err4; lvx v0,r4,r16
VPERM(v15,v1,v0,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,128
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err4; stvx v8,r0,r3
err4; stvx v9,r3,r9
err4; stvx v10,r3,r10
err4; stvx v11,r3,r11
err4; stvx v12,r3,r12
err4; stvx v13,r3,r14
err4; stvx v14,r3,r15
err4; stvx v15,r3,r16
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,128
bdnz 8b
powerpc: Fix usage of register macros getting ready for %r0 change Anything that uses a constructed instruction (ie. from ppc-opcode.h), need to use the new R0 macro, as %r0 is not going to work. Also convert usages of macros where we are just determining an offset (usually for a load/store), like: std r14,STK_REG(r14)(r1) Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since it's just calculating an offset. Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2012-06-25 17:33:10 +04:00
ld r14,STK_REG(R14)(r1)
ld r15,STK_REG(R15)(r1)
ld r16,STK_REG(R16)(r1)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
/* Up to 127B to go */
clrldi r5,r5,(64-7)
srdi r6,r5,4
mtocrf 0x01,r6
bf cr7*4+1,9f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v3,r0,r4
VPERM(v8,v0,v3,v16)
err3; lvx v2,r4,r9
VPERM(v9,v3,v2,v16)
err3; lvx v1,r4,r10
VPERM(v10,v2,v1,v16)
err3; lvx v0,r4,r11
VPERM(v11,v1,v0,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,64
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
err3; stvx v9,r3,r9
err3; stvx v10,r3,r10
err3; stvx v11,r3,r11
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,64
9: bf cr7*4+2,10f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
VPERM(v8,v0,v1,v16)
err3; lvx v0,r4,r9
VPERM(v9,v1,v0,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,32
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
err3; stvx v9,r3,r9
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,32
10: bf cr7*4+3,11f
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; lvx v1,r0,r4
VPERM(v8,v0,v1,v16)
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r4,r4,16
powerpc: Change vrX register defines to vX to match gcc and glibc As our various loops (copy, string, crypto etc) get more complicated, we want to share implementations between userspace (eg glibc) and the kernel. We also want to write userspace test harnesses to put in tools/testing/selftest. One gratuitous difference between userspace and the kernel is the VMX register definitions - the kernel uses vrX whereas both gcc and glibc use vX. Change the kernel to match userspace. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-02-10 01:51:22 +03:00
err3; stvx v8,r0,r3
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX Implement a POWER7 optimised copy_to_user/copy_from_user using VMX. For large aligned copies this new loop is over 10% faster, and for large unaligned copies it is over 200% faster. If we take a fault we fall back to the old version, this keeps things relatively simple and easy to verify. On POWER7 unaligned stores rarely slow down - they only flush when a store crosses a 4KB page boundary. Furthermore this flush is handled completely in hardware and should be 20-30 cycles. Unaligned loads on the other hand flush much more often - whenever crossing a 128 byte cache line, or a 32 byte sector if either sector is an L1 miss. Considering this information we really want to get the loads aligned and not worry about the alignment of the stores. Microbenchmarks confirm that this approach is much faster than the current unaligned copy loop that uses shifts and rotates to ensure both loads and stores are aligned. We also want to try and do the stores in cacheline aligned, cacheline sized chunks. If the store queue is unable to merge an entire cacheline of stores then the L2 cache will have to do a read/modify/write. Even worse, we will serialise this with the stores in the next iteration of the copy loop since both iterations hit the same cacheline. Based on this, the new loop does the following things: 1 - 127 bytes Get the source 8 byte aligned and use 8 byte loads and stores. Pretty boring and similar to how the current loop works. 128 - 4095 bytes Get the source 8 byte aligned and use 8 byte loads and stores, 1 cacheline at a time. We aren't doing the stores in cacheline aligned chunks so we will potentially serialise once per cacheline. Even so it is much better than the loop we have today. 4096 - bytes If both source and destination have the same alignment get them both 16 byte aligned, then get the destination cacheline aligned. Do cacheline sized loads and stores using VMX. If source and destination do not have the same alignment, we get the destination cacheline aligned, and use permute to do aligned loads. In both cases the VMX loop should be optimal - we always do aligned loads and stores and are always doing stores in cacheline aligned, cacheline sized chunks. To be able to use VMX we must be careful about interrupts and sleeping. We don't use the VMX loop when in an interrupt (which should be rare anyway) and we wrap the VMX loop in disable/enable_pagefault and fall back to the existing copy_tofrom_user loop if we do need to sleep. The VMX breakpoint of 4096 bytes was chosen using this microbenchmark: http://ozlabs.org/~anton/junkcode/copy_to_user.c Since we are using VMX and there is a cost to saving and restoring the user VMX state there are two broad cases we need to benchmark: - Best case - userspace never uses VMX - Worst case - userspace always uses VMX In reality a userspace process will sit somewhere between these two extremes. Since we need to test both aligned and unaligned copies we end up with 4 combinations. The point at which the VMX loop begins to win is: 0% VMX aligned 2048 bytes unaligned 2048 bytes 100% VMX aligned 16384 bytes unaligned 8192 bytes Considering this is a microbenchmark, the data is hot in cache and the VMX loop has better store queue merging properties we set the breakpoint to 4096 bytes, a little below the unaligned breakpoints. Some future optimisations we can look at: - Looking at the perf data, a significant part of the cost when a task is always using VMX is the extra exception we take to restore the VMX state. As such we should do something similar to the x86 optimisation that restores FPU state for heavy users. ie: /* * If the task has used fpu the last 5 timeslices, just do a full * restore of the math state immediately to avoid the trap; the * chances of needing FPU soon are obviously high now */ preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5; and /* * fpu_counter contains the number of consecutive context switches * that the FPU is used. If this is over a threshold, the lazy fpu * saving becomes unlazy to save the trap. This is an unsigned char * so that after 256 times the counter wraps and the behavior turns * lazy again; this to deal with bursty apps that only use FPU for * a short time */ - We could create a paca bit to mirror the VMX enabled MSR bit and check that first, avoiding multiple calls to calling enable_kernel_altivec. That should help with iovec based system calls like readv. - We could have two VMX breakpoints, one for when we know the user VMX state is loaded into the registers and one when it isn't. This could be a second bit in the paca so we can calculate the break points quickly. - One suggestion from Ben was to save and restore the VSX registers we use inline instead of using enable_kernel_altivec. [BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 00:11:45 +04:00
addi r3,r3,16
/* Up to 15B to go */
11: clrldi r5,r5,(64-4)
addi r4,r4,-16 /* Unwind the +16 load offset */
mtocrf 0x01,r5
bf cr7*4+0,12f
err3; lwz r0,0(r4) /* Less chance of a reject with word ops */
err3; lwz r6,4(r4)
addi r4,r4,8
err3; stw r0,0(r3)
err3; stw r6,4(r3)
addi r3,r3,8
12: bf cr7*4+1,13f
err3; lwz r0,0(r4)
addi r4,r4,4
err3; stw r0,0(r3)
addi r3,r3,4
13: bf cr7*4+2,14f
err3; lhz r0,0(r4)
addi r4,r4,2
err3; sth r0,0(r3)
addi r3,r3,2
14: bf cr7*4+3,15f
err3; lbz r0,0(r4)
err3; stb r0,0(r3)
15: addi r1,r1,STACKFRAMESIZE
powerpc: No need to use dot symbols when branching to a function binutils is smart enough to know that a branch to a function descriptor is actually a branch to the functions text address. Alan tells me that binutils has been doing this for 9 years. Signed-off-by: Anton Blanchard <anton@samba.org>
2014-02-04 09:04:35 +04:00
b exit_vmx_usercopy /* tail call optimise */
powerpc: Fix comment typos 'CONFiG_ALTIVEC' Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-09-26 21:45:34 +04:00
#endif /* CONFIG_ALTIVEC */