License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 17:07:57 +03:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
/*
|
|
|
|
* This file is included twice from vdso2c.c. It generates code for 32-bit
|
|
|
|
* and 64-bit vDSOs. We need both for 64-bit builds, since 32-bit vDSOs
|
|
|
|
* are built for 32-bit userspace.
|
|
|
|
*/
|
|
|
|
|
2014-07-11 05:13:16 +04:00
|
|
|
static void BITSFUNC(go)(void *raw_addr, size_t raw_len,
|
|
|
|
void *stripped_addr, size_t stripped_len,
|
2014-06-19 02:59:47 +04:00
|
|
|
FILE *outfile, const char *name)
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
{
|
|
|
|
int found_load = 0;
|
|
|
|
unsigned long load_size = -1; /* Work around bogus warning */
|
2014-07-11 05:13:16 +04:00
|
|
|
unsigned long mapping_size;
|
|
|
|
ELF(Ehdr) *hdr = (ELF(Ehdr) *)raw_addr;
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
int i;
|
|
|
|
unsigned long j;
|
2014-06-19 02:59:47 +04:00
|
|
|
ELF(Shdr) *symtab_hdr = NULL, *strtab_hdr, *secstrings_hdr,
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
*alt_sec = NULL;
|
2014-06-19 02:59:47 +04:00
|
|
|
ELF(Dyn) *dyn = 0, *dyn_end = 0;
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
const char *secstrings;
|
2014-07-11 05:13:15 +04:00
|
|
|
INT_BITS syms[NSYMS] = {};
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
|
2014-07-11 05:13:16 +04:00
|
|
|
ELF(Phdr) *pt = (ELF(Phdr) *)(raw_addr + GET_LE(&hdr->e_phoff));
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
|
2016-09-29 14:51:00 +03:00
|
|
|
if (GET_LE(&hdr->e_type) != ET_DYN)
|
2016-07-19 00:46:35 +03:00
|
|
|
fail("input is not a shared object\n");
|
|
|
|
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
/* Walk the segment table. */
|
2014-06-07 01:30:37 +04:00
|
|
|
for (i = 0; i < GET_LE(&hdr->e_phnum); i++) {
|
|
|
|
if (GET_LE(&pt[i].p_type) == PT_LOAD) {
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
if (found_load)
|
|
|
|
fail("multiple PT_LOAD segs\n");
|
|
|
|
|
2014-06-07 01:30:37 +04:00
|
|
|
if (GET_LE(&pt[i].p_offset) != 0 ||
|
|
|
|
GET_LE(&pt[i].p_vaddr) != 0)
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fail("PT_LOAD in wrong place\n");
|
|
|
|
|
2014-06-07 01:30:37 +04:00
|
|
|
if (GET_LE(&pt[i].p_memsz) != GET_LE(&pt[i].p_filesz))
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fail("cannot handle memsz != filesz\n");
|
|
|
|
|
2014-06-07 01:30:37 +04:00
|
|
|
load_size = GET_LE(&pt[i].p_memsz);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
found_load = 1;
|
2014-06-07 01:30:37 +04:00
|
|
|
} else if (GET_LE(&pt[i].p_type) == PT_DYNAMIC) {
|
2014-07-11 05:13:16 +04:00
|
|
|
dyn = raw_addr + GET_LE(&pt[i].p_offset);
|
|
|
|
dyn_end = raw_addr + GET_LE(&pt[i].p_offset) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&pt[i].p_memsz);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
}
|
|
|
|
if (!found_load)
|
|
|
|
fail("no PT_LOAD seg\n");
|
2014-07-11 05:13:16 +04:00
|
|
|
|
|
|
|
if (stripped_len < load_size)
|
|
|
|
fail("stripped input is too short\n");
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
|
2016-07-19 00:46:35 +03:00
|
|
|
if (!dyn)
|
|
|
|
fail("input has no PT_DYNAMIC section -- your toolchain is buggy\n");
|
|
|
|
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
/* Walk the dynamic table */
|
2014-05-31 04:03:22 +04:00
|
|
|
for (i = 0; dyn + i < dyn_end &&
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&dyn[i].d_tag) != DT_NULL; i++) {
|
|
|
|
typeof(dyn[i].d_tag) tag = GET_LE(&dyn[i].d_tag);
|
2014-06-25 00:46:53 +04:00
|
|
|
if (tag == DT_REL || tag == DT_RELSZ || tag == DT_RELA ||
|
2014-05-30 19:48:49 +04:00
|
|
|
tag == DT_RELENT || tag == DT_TEXTREL)
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fail("vdso image contains dynamic relocations\n");
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Walk the section table */
|
2014-07-11 05:13:16 +04:00
|
|
|
secstrings_hdr = raw_addr + GET_LE(&hdr->e_shoff) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&hdr->e_shentsize)*GET_LE(&hdr->e_shstrndx);
|
2014-07-11 05:13:16 +04:00
|
|
|
secstrings = raw_addr + GET_LE(&secstrings_hdr->sh_offset);
|
2014-06-07 01:30:37 +04:00
|
|
|
for (i = 0; i < GET_LE(&hdr->e_shnum); i++) {
|
2014-07-11 05:13:16 +04:00
|
|
|
ELF(Shdr) *sh = raw_addr + GET_LE(&hdr->e_shoff) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&hdr->e_shentsize) * i;
|
|
|
|
if (GET_LE(&sh->sh_type) == SHT_SYMTAB)
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
symtab_hdr = sh;
|
|
|
|
|
2014-06-07 01:30:37 +04:00
|
|
|
if (!strcmp(secstrings + GET_LE(&sh->sh_name),
|
2014-05-31 04:03:22 +04:00
|
|
|
".altinstructions"))
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
alt_sec = sh;
|
|
|
|
}
|
|
|
|
|
2014-05-30 19:48:48 +04:00
|
|
|
if (!symtab_hdr)
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fail("no symbol table\n");
|
|
|
|
|
2014-07-11 05:13:16 +04:00
|
|
|
strtab_hdr = raw_addr + GET_LE(&hdr->e_shoff) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&hdr->e_shentsize) * GET_LE(&symtab_hdr->sh_link);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
|
|
|
|
/* Walk the symbol table */
|
2014-05-31 04:03:22 +04:00
|
|
|
for (i = 0;
|
2014-06-07 01:30:37 +04:00
|
|
|
i < GET_LE(&symtab_hdr->sh_size) / GET_LE(&symtab_hdr->sh_entsize);
|
2014-05-30 19:48:49 +04:00
|
|
|
i++) {
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
int k;
|
2014-07-11 05:13:16 +04:00
|
|
|
ELF(Sym) *sym = raw_addr + GET_LE(&symtab_hdr->sh_offset) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&symtab_hdr->sh_entsize) * i;
|
2014-07-11 05:13:16 +04:00
|
|
|
const char *name = raw_addr + GET_LE(&strtab_hdr->sh_offset) +
|
2014-06-07 01:30:37 +04:00
|
|
|
GET_LE(&sym->st_name);
|
2014-06-13 04:53:12 +04:00
|
|
|
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
for (k = 0; k < NSYMS; k++) {
|
2014-06-19 02:59:48 +04:00
|
|
|
if (!strcmp(name, required_syms[k].name)) {
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
if (syms[k]) {
|
|
|
|
fail("duplicate symbol %s\n",
|
2014-06-19 02:59:48 +04:00
|
|
|
required_syms[k].name);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
2014-07-11 05:13:15 +04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Careful: we use negative addresses, but
|
|
|
|
* st_value is unsigned, so we rely
|
|
|
|
* on syms[k] being a signed type of the
|
|
|
|
* correct width.
|
|
|
|
*/
|
2014-06-07 01:30:37 +04:00
|
|
|
syms[k] = GET_LE(&sym->st_value);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
}
|
2014-06-19 02:59:48 +04:00
|
|
|
}
|
|
|
|
|
2014-05-05 23:19:35 +04:00
|
|
|
/* Validate mapping addresses. */
|
|
|
|
for (i = 0; i < sizeof(special_pages) / sizeof(special_pages[0]); i++) {
|
2014-07-31 01:59:49 +04:00
|
|
|
INT_BITS symval = syms[special_pages[i]];
|
|
|
|
|
|
|
|
if (!symval)
|
2014-05-05 23:19:35 +04:00
|
|
|
continue; /* The mapping isn't used; ignore it. */
|
|
|
|
|
2014-07-31 01:59:49 +04:00
|
|
|
if (symval % 4096)
|
2014-05-05 23:19:35 +04:00
|
|
|
fail("%s must be a multiple of 4096\n",
|
2014-06-19 02:59:48 +04:00
|
|
|
required_syms[i].name);
|
2014-07-31 01:59:49 +04:00
|
|
|
if (symval + 4096 < syms[sym_vvar_start])
|
|
|
|
fail("%s underruns vvar_start\n",
|
2014-06-19 02:59:48 +04:00
|
|
|
required_syms[i].name);
|
2014-07-31 01:59:49 +04:00
|
|
|
if (symval + 4096 > 0)
|
2014-07-11 05:13:15 +04:00
|
|
|
fail("%s is on the wrong side of the vdso text\n",
|
2014-06-19 02:59:48 +04:00
|
|
|
required_syms[i].name);
|
2014-05-05 23:19:35 +04:00
|
|
|
}
|
2014-07-11 05:13:15 +04:00
|
|
|
if (syms[sym_vvar_start] % 4096)
|
|
|
|
fail("vvar_begin must be a multiple of 4096\n");
|
2014-05-05 23:19:35 +04:00
|
|
|
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
if (!name) {
|
2014-07-11 05:13:16 +04:00
|
|
|
fwrite(stripped_addr, stripped_len, 1, outfile);
|
2014-05-30 19:48:48 +04:00
|
|
|
return;
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
|
2014-07-11 05:13:16 +04:00
|
|
|
mapping_size = (stripped_len + 4095) / 4096 * 4096;
|
|
|
|
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fprintf(outfile, "/* AUTOMATICALLY GENERATED -- DO NOT EDIT */\n\n");
|
|
|
|
fprintf(outfile, "#include <linux/linkage.h>\n");
|
|
|
|
fprintf(outfile, "#include <asm/page_types.h>\n");
|
|
|
|
fprintf(outfile, "#include <asm/vdso.h>\n");
|
|
|
|
fprintf(outfile, "\n");
|
|
|
|
fprintf(outfile,
|
2016-02-18 01:41:17 +03:00
|
|
|
"static unsigned char raw_data[%lu] __ro_after_init __aligned(PAGE_SIZE) = {",
|
2014-07-11 05:13:16 +04:00
|
|
|
mapping_size);
|
|
|
|
for (j = 0; j < stripped_len; j++) {
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
if (j % 10 == 0)
|
|
|
|
fprintf(outfile, "\n\t");
|
2014-07-11 05:13:16 +04:00
|
|
|
fprintf(outfile, "0x%02X, ",
|
|
|
|
(int)((unsigned char *)stripped_addr)[j]);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
fprintf(outfile, "\n};\n\n");
|
|
|
|
|
|
|
|
fprintf(outfile, "const struct vdso_image %s = {\n", name);
|
|
|
|
fprintf(outfile, "\t.data = raw_data,\n");
|
2014-07-11 05:13:16 +04:00
|
|
|
fprintf(outfile, "\t.size = %lu,\n", mapping_size);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
if (alt_sec) {
|
|
|
|
fprintf(outfile, "\t.alt = %lu,\n",
|
2014-06-07 01:30:37 +04:00
|
|
|
(unsigned long)GET_LE(&alt_sec->sh_offset));
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
fprintf(outfile, "\t.alt_len = %lu,\n",
|
2014-06-07 01:30:37 +04:00
|
|
|
(unsigned long)GET_LE(&alt_sec->sh_size));
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
for (i = 0; i < NSYMS; i++) {
|
2014-06-19 02:59:48 +04:00
|
|
|
if (required_syms[i].export && syms[i])
|
2014-07-11 05:13:15 +04:00
|
|
|
fprintf(outfile, "\t.sym_%s = %" PRIi64 ",\n",
|
|
|
|
required_syms[i].name, (int64_t)syms[i]);
|
x86, vdso: Reimplement vdso.so preparation in build-time C
Currently, vdso.so files are prepared and analyzed by a combination
of objcopy, nm, some linker script tricks, and some simple ELF
parsers in the kernel. Replace all of that with plain C code that
runs at build time.
All five vdso images now generate .c files that are compiled and
linked in to the kernel image.
This should cause only one userspace-visible change: the loaded vDSO
images are stripped more heavily than they used to be. Everything
outside the loadable segment is dropped. In particular, this causes
the section table and section name strings to be missing. This
should be fine: real dynamic loaders don't load or inspect these
tables anyway. The result is roughly equivalent to eu-strip's
--strip-sections option.
The purpose of this change is to enable the vvar and hpet mappings
to be moved to the page following the vDSO load segment. Currently,
it is possible for the section table to extend into the page after
the load segment, so, if we map it, it risks overlapping the vvar or
hpet page. This happens whenever the load segment is just under a
multiple of PAGE_SIZE.
The only real subtlety here is that the old code had a C file with
inline assembler that did 'call VDSO32_vsyscall' and a linker script
that defined 'VDSO32_vsyscall = __kernel_vsyscall'. This most
likely worked by accident: the linker script entry defines a symbol
associated with an address as opposed to an alias for the real
dynamic symbol __kernel_vsyscall. That caused ld to relocate the
reference at link time instead of leaving an interposable dynamic
relocation. Since the VDSO32_vsyscall hack is no longer needed, I
now use 'call __kernel_vsyscall', and I added -Bsymbolic to make it
work. vdso2c will generate an error and abort the build if the
resulting image contains any dynamic relocations, so we won't
silently generate bad vdso images.
(Dynamic relocations are a problem because nothing will even attempt
to relocate the vdso.)
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/2c4fcf45524162a34d87fdda1eb046b2a5cecee7.1399317206.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2014-05-05 23:19:34 +04:00
|
|
|
}
|
|
|
|
fprintf(outfile, "};\n");
|
|
|
|
}
|