WSL2-Linux-Kernel/drivers/usb/serial/quatech2.c

1037 строки
25 KiB
C
Исходник Обычный вид История

/*
* usb-serial driver for Quatech USB 2 devices
*
* Copyright (C) 2012 Bill Pemberton (wfp5p@virginia.edu)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License version 2
* as published by the Free Software Foundation.
*
*
* These devices all have only 1 bulk in and 1 bulk out that is shared
* for all serial ports.
*
*/
#include <asm/unaligned.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/serial.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#include <linux/serial_reg.h>
#include <linux/uaccess.h>
/* default urb timeout for usb operations */
#define QT2_USB_TIMEOUT USB_CTRL_SET_TIMEOUT
#define QT_OPEN_CLOSE_CHANNEL 0xca
#define QT_SET_GET_DEVICE 0xc2
#define QT_SET_GET_REGISTER 0xc0
#define QT_GET_SET_PREBUF_TRIG_LVL 0xcc
#define QT_SET_ATF 0xcd
#define QT_TRANSFER_IN 0xc0
#define QT_HW_FLOW_CONTROL_MASK 0xc5
#define QT_SW_FLOW_CONTROL_MASK 0xc6
#define QT2_BREAK_CONTROL 0xc8
#define QT2_GET_SET_UART 0xc1
#define QT2_FLUSH_DEVICE 0xc4
#define QT2_GET_SET_QMCR 0xe1
#define QT2_QMCR_RS232 0x40
#define QT2_QMCR_RS422 0x10
#define SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
#define SERIAL_EVEN_PARITY (UART_LCR_PARITY | UART_LCR_EPAR)
/* status bytes for the device */
#define QT2_CONTROL_BYTE 0x1b
#define QT2_LINE_STATUS 0x00 /* following 1 byte is line status */
#define QT2_MODEM_STATUS 0x01 /* following 1 byte is modem status */
#define QT2_XMIT_HOLD 0x02 /* following 2 bytes are ?? */
#define QT2_CHANGE_PORT 0x03 /* following 1 byte is port to change to */
#define QT2_REC_FLUSH 0x04 /* no following info */
#define QT2_XMIT_FLUSH 0x05 /* no following info */
#define QT2_CONTROL_ESCAPE 0xff /* pass through previous 2 control bytes */
#define MAX_BAUD_RATE 921600
#define DEFAULT_BAUD_RATE 9600
#define QT2_READ_BUFFER_SIZE 512 /* size of read buffer */
#define QT2_WRITE_BUFFER_SIZE 512 /* size of write buffer */
#define QT2_WRITE_CONTROL_SIZE 5 /* control bytes used for a write */
#define DRIVER_DESC "Quatech 2nd gen USB to Serial Driver"
#define USB_VENDOR_ID_QUATECH 0x061d
#define QUATECH_SSU2_100 0xC120 /* RS232 single port */
#define QUATECH_DSU2_100 0xC140 /* RS232 dual port */
#define QUATECH_DSU2_400 0xC150 /* RS232/422/485 dual port */
#define QUATECH_QSU2_100 0xC160 /* RS232 four port */
#define QUATECH_QSU2_400 0xC170 /* RS232/422/485 four port */
#define QUATECH_ESU2_100 0xC1A0 /* RS232 eight port */
#define QUATECH_ESU2_400 0xC180 /* RS232/422/485 eight port */
struct qt2_device_detail {
int product_id;
int num_ports;
};
#define QT_DETAILS(prod, ports) \
.product_id = (prod), \
.num_ports = (ports)
static const struct qt2_device_detail qt2_device_details[] = {
{QT_DETAILS(QUATECH_SSU2_100, 1)},
{QT_DETAILS(QUATECH_DSU2_400, 2)},
{QT_DETAILS(QUATECH_DSU2_100, 2)},
{QT_DETAILS(QUATECH_QSU2_400, 4)},
{QT_DETAILS(QUATECH_QSU2_100, 4)},
{QT_DETAILS(QUATECH_ESU2_400, 8)},
{QT_DETAILS(QUATECH_ESU2_100, 8)},
{QT_DETAILS(0, 0)} /* Terminating entry */
};
static const struct usb_device_id id_table[] = {
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU2_100)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_DSU2_100)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_DSU2_400)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_QSU2_100)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_QSU2_400)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_ESU2_100)},
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_ESU2_400)},
{} /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, id_table);
struct qt2_serial_private {
unsigned char current_port; /* current port for incoming data */
struct urb *read_urb; /* shared among all ports */
char *read_buffer;
};
struct qt2_port_private {
u8 device_port;
spinlock_t urb_lock;
bool urb_in_use;
struct urb *write_urb;
char *write_buffer;
spinlock_t lock;
u8 shadowLSR;
u8 shadowMSR;
struct usb_serial_port *port;
};
static void qt2_update_lsr(struct usb_serial_port *port, unsigned char *ch);
static void qt2_update_msr(struct usb_serial_port *port, unsigned char *ch);
static void qt2_write_bulk_callback(struct urb *urb);
static void qt2_read_bulk_callback(struct urb *urb);
static void qt2_release(struct usb_serial *serial)
{
struct qt2_serial_private *serial_priv;
serial_priv = usb_get_serial_data(serial);
usb_free_urb(serial_priv->read_urb);
kfree(serial_priv->read_buffer);
kfree(serial_priv);
}
static inline int calc_baud_divisor(int baudrate)
{
int divisor, rem;
divisor = MAX_BAUD_RATE / baudrate;
rem = MAX_BAUD_RATE % baudrate;
/* Round to nearest divisor */
if (((rem * 2) >= baudrate) && (baudrate != 110))
divisor++;
return divisor;
}
static inline int qt2_set_port_config(struct usb_device *dev,
unsigned char port_number,
u16 baudrate, u16 lcr)
{
int divisor = calc_baud_divisor(baudrate);
u16 index = ((u16) (lcr << 8) | (u16) (port_number));
return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
QT2_GET_SET_UART, 0x40,
divisor, index, NULL, 0, QT2_USB_TIMEOUT);
}
static inline int qt2_control_msg(struct usb_device *dev,
u8 request, u16 data, u16 index)
{
return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
request, 0x40, data, index,
NULL, 0, QT2_USB_TIMEOUT);
}
static inline int qt2_setdevice(struct usb_device *dev, u8 *data)
{
u16 x = ((u16) (data[1] << 8) | (u16) (data[0]));
return qt2_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
}
static inline int qt2_getdevice(struct usb_device *dev, u8 *data)
{
return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
QT_SET_GET_DEVICE, 0xc0, 0, 0,
data, 3, QT2_USB_TIMEOUT);
}
static inline int qt2_getregister(struct usb_device *dev,
u8 uart,
u8 reg,
u8 *data)
{
return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
QT_SET_GET_REGISTER, 0xc0, reg,
uart, data, sizeof(*data), QT2_USB_TIMEOUT);
}
static inline int qt2_setregister(struct usb_device *dev,
u8 uart, u8 reg, u16 data)
{
u16 value = (data << 8) | reg;
return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
QT_SET_GET_REGISTER, 0x40, value, uart,
NULL, 0, QT2_USB_TIMEOUT);
}
static inline int update_mctrl(struct qt2_port_private *port_priv,
unsigned int set, unsigned int clear)
{
struct usb_serial_port *port = port_priv->port;
struct usb_device *dev = port->serial->dev;
unsigned urb_value;
int status;
if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
dev_dbg(&port->dev,
"update_mctrl - DTR|RTS not being set|cleared\n");
return 0; /* no change */
}
clear &= ~set; /* 'set' takes precedence over 'clear' */
urb_value = 0;
if (set & TIOCM_DTR)
urb_value |= UART_MCR_DTR;
if (set & TIOCM_RTS)
urb_value |= UART_MCR_RTS;
status = qt2_setregister(dev, port_priv->device_port, UART_MCR,
urb_value);
if (status < 0)
dev_err(&port->dev,
"update_mctrl - Error from MODEM_CTRL urb: %i\n",
status);
return status;
}
static int qt2_calc_num_ports(struct usb_serial *serial)
{
struct qt2_device_detail d;
int i;
for (i = 0; d = qt2_device_details[i], d.product_id != 0; i++) {
if (d.product_id == le16_to_cpu(serial->dev->descriptor.idProduct))
return d.num_ports;
}
/* we didn't recognize the device */
dev_err(&serial->dev->dev,
"don't know the number of ports, assuming 1\n");
return 1;
}
static void qt2_set_termios(struct tty_struct *tty,
struct usb_serial_port *port,
struct ktermios *old_termios)
{
struct usb_device *dev = port->serial->dev;
struct qt2_port_private *port_priv;
struct ktermios *termios = &tty->termios;
u16 baud;
unsigned int cflag = termios->c_cflag;
u16 new_lcr = 0;
int status;
port_priv = usb_get_serial_port_data(port);
if (cflag & PARENB) {
if (cflag & PARODD)
new_lcr |= UART_LCR_PARITY;
else
new_lcr |= SERIAL_EVEN_PARITY;
}
switch (cflag & CSIZE) {
case CS5:
new_lcr |= UART_LCR_WLEN5;
break;
case CS6:
new_lcr |= UART_LCR_WLEN6;
break;
case CS7:
new_lcr |= UART_LCR_WLEN7;
break;
default:
case CS8:
new_lcr |= UART_LCR_WLEN8;
break;
}
baud = tty_get_baud_rate(tty);
if (!baud)
baud = 9600;
status = qt2_set_port_config(dev, port_priv->device_port, baud,
new_lcr);
if (status < 0)
dev_err(&port->dev, "%s - qt2_set_port_config failed: %i\n",
__func__, status);
if (cflag & CRTSCTS)
status = qt2_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
SERIAL_CRTSCTS,
port_priv->device_port);
else
status = qt2_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
0, port_priv->device_port);
if (status < 0)
dev_err(&port->dev, "%s - set HW flow control failed: %i\n",
__func__, status);
if (I_IXOFF(tty) || I_IXON(tty)) {
u16 x = ((u16) (START_CHAR(tty) << 8) | (u16) (STOP_CHAR(tty)));
status = qt2_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
x, port_priv->device_port);
} else
status = qt2_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
0, port_priv->device_port);
if (status < 0)
dev_err(&port->dev, "%s - set SW flow control failed: %i\n",
__func__, status);
}
static int qt2_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct usb_serial *serial;
struct qt2_port_private *port_priv;
u8 *data;
u16 device_port;
int status;
unsigned long flags;
USB: serial: ports: add minor and port number The usb_serial_port structure had the number field, which was the minor number for the port, which almost no one really cared about. They really wanted the number of the port within the device, which you had to subtract from the minor of the parent usb_serial_device structure. To clean this up, provide the real minor number of the port, and the number of the port within the serial device separately, as these numbers might not be related in the future. Bonus is that this cleans up a lot of logic in the drivers, and saves lines overall. Tested-by: Tobias Winter <tobias@linuxdingsda.de> Reviewed-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -- drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++-------- drivers/usb/serial/ark3116.c | 2 - drivers/usb/serial/bus.c | 6 +-- drivers/usb/serial/console.c | 2 - drivers/usb/serial/cp210x.c | 2 - drivers/usb/serial/cypress_m8.c | 4 +- drivers/usb/serial/digi_acceleport.c | 6 --- drivers/usb/serial/f81232.c | 5 +- drivers/usb/serial/garmin_gps.c | 6 +-- drivers/usb/serial/io_edgeport.c | 58 ++++++++++++-------------------- drivers/usb/serial/io_ti.c | 21 ++++------- drivers/usb/serial/keyspan.c | 29 +++++++--------- drivers/usb/serial/metro-usb.c | 4 +- drivers/usb/serial/mos7720.c | 37 +++++++++----------- drivers/usb/serial/mos7840.c | 52 +++++++++------------------- drivers/usb/serial/opticon.c | 2 - drivers/usb/serial/pl2303.c | 2 - drivers/usb/serial/quatech2.c | 7 +-- drivers/usb/serial/sierra.c | 2 - drivers/usb/serial/ti_usb_3410_5052.c | 10 ++--- drivers/usb/serial/usb-serial.c | 7 ++- drivers/usb/serial/usb_wwan.c | 2 - drivers/usb/serial/whiteheat.c | 20 +++++------ include/linux/usb/serial.h | 6 ++- 24 files changed, 133 insertions(+), 180 deletions(-)
2013-06-06 21:32:00 +04:00
device_port = port->port_number;
serial = port->serial;
port_priv = usb_get_serial_port_data(port);
/* set the port to RS232 mode */
status = qt2_control_msg(serial->dev, QT2_GET_SET_QMCR,
QT2_QMCR_RS232, device_port);
if (status < 0) {
dev_err(&port->dev,
"%s failed to set RS232 mode for port %i error %i\n",
__func__, device_port, status);
return status;
}
data = kzalloc(2, GFP_KERNEL);
if (!data)
return -ENOMEM;
/* open the port */
status = usb_control_msg(serial->dev,
usb_rcvctrlpipe(serial->dev, 0),
QT_OPEN_CLOSE_CHANNEL,
0xc0, 0,
device_port, data, 2, QT2_USB_TIMEOUT);
if (status < 0) {
dev_err(&port->dev, "%s - open port failed %i\n", __func__,
status);
kfree(data);
return status;
}
spin_lock_irqsave(&port_priv->lock, flags);
port_priv->shadowLSR = data[0];
port_priv->shadowMSR = data[1];
spin_unlock_irqrestore(&port_priv->lock, flags);
kfree(data);
/* set to default speed and 8bit word size */
status = qt2_set_port_config(serial->dev, device_port,
DEFAULT_BAUD_RATE, UART_LCR_WLEN8);
if (status < 0) {
USB: serial: ports: add minor and port number The usb_serial_port structure had the number field, which was the minor number for the port, which almost no one really cared about. They really wanted the number of the port within the device, which you had to subtract from the minor of the parent usb_serial_device structure. To clean this up, provide the real minor number of the port, and the number of the port within the serial device separately, as these numbers might not be related in the future. Bonus is that this cleans up a lot of logic in the drivers, and saves lines overall. Tested-by: Tobias Winter <tobias@linuxdingsda.de> Reviewed-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -- drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++-------- drivers/usb/serial/ark3116.c | 2 - drivers/usb/serial/bus.c | 6 +-- drivers/usb/serial/console.c | 2 - drivers/usb/serial/cp210x.c | 2 - drivers/usb/serial/cypress_m8.c | 4 +- drivers/usb/serial/digi_acceleport.c | 6 --- drivers/usb/serial/f81232.c | 5 +- drivers/usb/serial/garmin_gps.c | 6 +-- drivers/usb/serial/io_edgeport.c | 58 ++++++++++++-------------------- drivers/usb/serial/io_ti.c | 21 ++++------- drivers/usb/serial/keyspan.c | 29 +++++++--------- drivers/usb/serial/metro-usb.c | 4 +- drivers/usb/serial/mos7720.c | 37 +++++++++----------- drivers/usb/serial/mos7840.c | 52 +++++++++------------------- drivers/usb/serial/opticon.c | 2 - drivers/usb/serial/pl2303.c | 2 - drivers/usb/serial/quatech2.c | 7 +-- drivers/usb/serial/sierra.c | 2 - drivers/usb/serial/ti_usb_3410_5052.c | 10 ++--- drivers/usb/serial/usb-serial.c | 7 ++- drivers/usb/serial/usb_wwan.c | 2 - drivers/usb/serial/whiteheat.c | 20 +++++------ include/linux/usb/serial.h | 6 ++- 24 files changed, 133 insertions(+), 180 deletions(-)
2013-06-06 21:32:00 +04:00
dev_err(&port->dev, "%s - initial setup failed (%i)\n",
__func__, device_port);
return status;
}
port_priv->device_port = (u8) device_port;
if (tty)
qt2_set_termios(tty, port, &tty->termios);
return 0;
}
static void qt2_close(struct usb_serial_port *port)
{
struct usb_serial *serial;
struct qt2_port_private *port_priv;
unsigned long flags;
int i;
serial = port->serial;
port_priv = usb_get_serial_port_data(port);
spin_lock_irqsave(&port_priv->urb_lock, flags);
usb_kill_urb(port_priv->write_urb);
port_priv->urb_in_use = false;
spin_unlock_irqrestore(&port_priv->urb_lock, flags);
/* flush the port transmit buffer */
i = usb_control_msg(serial->dev,
usb_rcvctrlpipe(serial->dev, 0),
QT2_FLUSH_DEVICE, 0x40, 1,
port_priv->device_port, NULL, 0, QT2_USB_TIMEOUT);
if (i < 0)
dev_err(&port->dev, "%s - transmit buffer flush failed: %i\n",
__func__, i);
/* flush the port receive buffer */
i = usb_control_msg(serial->dev,
usb_rcvctrlpipe(serial->dev, 0),
QT2_FLUSH_DEVICE, 0x40, 0,
port_priv->device_port, NULL, 0, QT2_USB_TIMEOUT);
if (i < 0)
dev_err(&port->dev, "%s - receive buffer flush failed: %i\n",
__func__, i);
/* close the port */
i = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0),
QT_OPEN_CLOSE_CHANNEL,
0x40, 0,
port_priv->device_port, NULL, 0, QT2_USB_TIMEOUT);
if (i < 0)
dev_err(&port->dev, "%s - close port failed %i\n",
__func__, i);
}
static void qt2_disconnect(struct usb_serial *serial)
{
struct qt2_serial_private *serial_priv = usb_get_serial_data(serial);
usb_kill_urb(serial_priv->read_urb);
}
static int get_serial_info(struct usb_serial_port *port,
struct serial_struct __user *retinfo)
{
struct serial_struct tmp;
if (!retinfo)
return -EFAULT;
memset(&tmp, 0, sizeof(tmp));
tmp.line = port->minor;
tmp.port = 0;
tmp.irq = 0;
tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
tmp.xmit_fifo_size = port->bulk_out_size;
tmp.baud_base = 9600;
tmp.close_delay = 5*HZ;
tmp.closing_wait = 30*HZ;
if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
return -EFAULT;
return 0;
}
static int qt2_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg)
{
struct usb_serial_port *port = tty->driver_data;
switch (cmd) {
case TIOCGSERIAL:
return get_serial_info(port,
(struct serial_struct __user *)arg);
default:
break;
}
return -ENOIOCTLCMD;
}
static void qt2_process_status(struct usb_serial_port *port, unsigned char *ch)
{
switch (*ch) {
case QT2_LINE_STATUS:
qt2_update_lsr(port, ch + 1);
break;
case QT2_MODEM_STATUS:
qt2_update_msr(port, ch + 1);
break;
}
}
/* not needed, kept to document functionality */
static void qt2_process_xmit_empty(struct usb_serial_port *port,
unsigned char *ch)
{
int bytes_written;
bytes_written = (int)(*ch) + (int)(*(ch + 1) << 4);
}
/* not needed, kept to document functionality */
static void qt2_process_flush(struct usb_serial_port *port, unsigned char *ch)
{
return;
}
static void qt2_process_read_urb(struct urb *urb)
{
struct usb_serial *serial;
struct qt2_serial_private *serial_priv;
struct usb_serial_port *port;
struct qt2_port_private *port_priv;
bool escapeflag;
unsigned char *ch;
int i;
unsigned char newport;
int len = urb->actual_length;
if (!len)
return;
ch = urb->transfer_buffer;
serial = urb->context;
serial_priv = usb_get_serial_data(serial);
port = serial->port[serial_priv->current_port];
port_priv = usb_get_serial_port_data(port);
for (i = 0; i < urb->actual_length; i++) {
ch = (unsigned char *)urb->transfer_buffer + i;
if ((i <= (len - 3)) &&
(*ch == QT2_CONTROL_BYTE) &&
(*(ch + 1) == QT2_CONTROL_BYTE)) {
escapeflag = false;
switch (*(ch + 2)) {
case QT2_LINE_STATUS:
case QT2_MODEM_STATUS:
if (i > (len - 4)) {
dev_warn(&port->dev,
"%s - status message too short\n",
__func__);
break;
}
qt2_process_status(port, ch + 2);
i += 3;
escapeflag = true;
break;
case QT2_XMIT_HOLD:
if (i > (len - 5)) {
dev_warn(&port->dev,
"%s - xmit_empty message too short\n",
__func__);
break;
}
qt2_process_xmit_empty(port, ch + 3);
i += 4;
escapeflag = true;
break;
case QT2_CHANGE_PORT:
if (i > (len - 4)) {
dev_warn(&port->dev,
"%s - change_port message too short\n",
__func__);
break;
}
tty_flip_buffer_push(&port->port);
newport = *(ch + 3);
if (newport > serial->num_ports) {
dev_err(&port->dev,
"%s - port change to invalid port: %i\n",
__func__, newport);
break;
}
serial_priv->current_port = newport;
port = serial->port[serial_priv->current_port];
port_priv = usb_get_serial_port_data(port);
i += 3;
escapeflag = true;
break;
case QT2_REC_FLUSH:
case QT2_XMIT_FLUSH:
qt2_process_flush(port, ch + 2);
i += 2;
escapeflag = true;
break;
case QT2_CONTROL_ESCAPE:
tty_buffer_request_room(&port->port, 2);
tty_insert_flip_string(&port->port, ch, 2);
i += 2;
escapeflag = true;
break;
default:
dev_warn(&port->dev,
"%s - unsupported command %i\n",
__func__, *(ch + 2));
break;
}
if (escapeflag)
continue;
}
tty_buffer_request_room(&port->port, 1);
tty_insert_flip_string(&port->port, ch, 1);
}
tty_flip_buffer_push(&port->port);
}
static void qt2_write_bulk_callback(struct urb *urb)
{
struct usb_serial_port *port;
struct qt2_port_private *port_priv;
port = urb->context;
port_priv = usb_get_serial_port_data(port);
spin_lock(&port_priv->urb_lock);
port_priv->urb_in_use = false;
usb_serial_port_softint(port);
spin_unlock(&port_priv->urb_lock);
}
static void qt2_read_bulk_callback(struct urb *urb)
{
struct usb_serial *serial = urb->context;
int status;
if (urb->status) {
dev_warn(&serial->dev->dev,
"%s - non-zero urb status: %i\n", __func__,
urb->status);
return;
}
qt2_process_read_urb(urb);
status = usb_submit_urb(urb, GFP_ATOMIC);
if (status != 0)
dev_err(&serial->dev->dev,
"%s - resubmit read urb failed: %i\n",
__func__, status);
}
static int qt2_setup_urbs(struct usb_serial *serial)
{
struct usb_serial_port *port0;
struct qt2_serial_private *serial_priv;
int status;
port0 = serial->port[0];
serial_priv = usb_get_serial_data(serial);
serial_priv->read_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!serial_priv->read_urb)
return -ENOMEM;
usb_fill_bulk_urb(serial_priv->read_urb, serial->dev,
usb_rcvbulkpipe(serial->dev,
port0->bulk_in_endpointAddress),
serial_priv->read_buffer,
QT2_READ_BUFFER_SIZE,
qt2_read_bulk_callback, serial);
status = usb_submit_urb(serial_priv->read_urb, GFP_KERNEL);
if (status != 0) {
dev_err(&serial->dev->dev,
"%s - submit read urb failed %i\n", __func__, status);
usb_free_urb(serial_priv->read_urb);
return status;
}
return 0;
}
static int qt2_attach(struct usb_serial *serial)
{
struct qt2_serial_private *serial_priv;
int status;
/* power on unit */
status = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
0xc2, 0x40, 0x8000, 0, NULL, 0,
QT2_USB_TIMEOUT);
if (status < 0) {
dev_err(&serial->dev->dev,
"%s - failed to power on unit: %i\n", __func__, status);
return status;
}
serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL);
if (!serial_priv)
return -ENOMEM;
serial_priv->read_buffer = kmalloc(QT2_READ_BUFFER_SIZE, GFP_KERNEL);
if (!serial_priv->read_buffer) {
status = -ENOMEM;
goto err_buf;
}
usb_set_serial_data(serial, serial_priv);
status = qt2_setup_urbs(serial);
if (status != 0)
goto attach_failed;
return 0;
attach_failed:
kfree(serial_priv->read_buffer);
err_buf:
kfree(serial_priv);
return status;
}
static int qt2_port_probe(struct usb_serial_port *port)
{
struct usb_serial *serial = port->serial;
struct qt2_port_private *port_priv;
u8 bEndpointAddress;
port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
if (!port_priv)
return -ENOMEM;
spin_lock_init(&port_priv->lock);
spin_lock_init(&port_priv->urb_lock);
port_priv->port = port;
port_priv->write_buffer = kmalloc(QT2_WRITE_BUFFER_SIZE, GFP_KERNEL);
if (!port_priv->write_buffer)
goto err_buf;
port_priv->write_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!port_priv->write_urb)
goto err_urb;
bEndpointAddress = serial->port[0]->bulk_out_endpointAddress;
usb_fill_bulk_urb(port_priv->write_urb, serial->dev,
usb_sndbulkpipe(serial->dev, bEndpointAddress),
port_priv->write_buffer,
QT2_WRITE_BUFFER_SIZE,
qt2_write_bulk_callback, port);
usb_set_serial_port_data(port, port_priv);
return 0;
err_urb:
kfree(port_priv->write_buffer);
err_buf:
kfree(port_priv);
return -ENOMEM;
}
static int qt2_port_remove(struct usb_serial_port *port)
{
struct qt2_port_private *port_priv;
port_priv = usb_get_serial_port_data(port);
usb_free_urb(port_priv->write_urb);
kfree(port_priv->write_buffer);
kfree(port_priv);
return 0;
}
static int qt2_tiocmget(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct usb_device *dev = port->serial->dev;
struct qt2_port_private *port_priv = usb_get_serial_port_data(port);
u8 *d;
int r;
d = kzalloc(2, GFP_KERNEL);
if (!d)
return -ENOMEM;
r = qt2_getregister(dev, port_priv->device_port, UART_MCR, d);
if (r < 0)
goto mget_out;
r = qt2_getregister(dev, port_priv->device_port, UART_MSR, d + 1);
if (r < 0)
goto mget_out;
r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
(d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
(d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
(d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
(d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
(d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
mget_out:
kfree(d);
return r;
}
static int qt2_tiocmset(struct tty_struct *tty,
unsigned int set, unsigned int clear)
{
struct qt2_port_private *port_priv;
port_priv = usb_get_serial_port_data(tty->driver_data);
return update_mctrl(port_priv, set, clear);
}
static void qt2_break_ctl(struct tty_struct *tty, int break_state)
{
struct usb_serial_port *port = tty->driver_data;
struct qt2_port_private *port_priv;
int status;
u16 val;
port_priv = usb_get_serial_port_data(port);
val = (break_state == -1) ? 1 : 0;
status = qt2_control_msg(port->serial->dev, QT2_BREAK_CONTROL,
val, port_priv->device_port);
if (status < 0)
dev_warn(&port->dev,
"%s - failed to send control message: %i\n", __func__,
status);
}
static void qt2_dtr_rts(struct usb_serial_port *port, int on)
{
struct usb_device *dev = port->serial->dev;
struct qt2_port_private *port_priv = usb_get_serial_port_data(port);
/* Disable flow control */
if (!on) {
if (qt2_setregister(dev, port_priv->device_port,
UART_MCR, 0) < 0)
dev_warn(&port->dev, "error from flowcontrol urb\n");
}
/* drop RTS and DTR */
if (on)
update_mctrl(port_priv, TIOCM_DTR | TIOCM_RTS, 0);
else
update_mctrl(port_priv, 0, TIOCM_DTR | TIOCM_RTS);
}
static void qt2_update_msr(struct usb_serial_port *port, unsigned char *ch)
{
struct qt2_port_private *port_priv;
u8 newMSR = (u8) *ch;
unsigned long flags;
port_priv = usb_get_serial_port_data(port);
spin_lock_irqsave(&port_priv->lock, flags);
port_priv->shadowMSR = newMSR;
spin_unlock_irqrestore(&port_priv->lock, flags);
if (newMSR & UART_MSR_ANY_DELTA) {
/* update input line counters */
if (newMSR & UART_MSR_DCTS)
port->icount.cts++;
if (newMSR & UART_MSR_DDSR)
port->icount.dsr++;
if (newMSR & UART_MSR_DDCD)
port->icount.dcd++;
if (newMSR & UART_MSR_TERI)
port->icount.rng++;
wake_up_interruptible(&port->port.delta_msr_wait);
}
}
static void qt2_update_lsr(struct usb_serial_port *port, unsigned char *ch)
{
struct qt2_port_private *port_priv;
struct async_icount *icount;
unsigned long flags;
u8 newLSR = (u8) *ch;
port_priv = usb_get_serial_port_data(port);
if (newLSR & UART_LSR_BI)
newLSR &= (u8) (UART_LSR_OE | UART_LSR_BI);
spin_lock_irqsave(&port_priv->lock, flags);
port_priv->shadowLSR = newLSR;
spin_unlock_irqrestore(&port_priv->lock, flags);
icount = &port->icount;
if (newLSR & UART_LSR_BRK_ERROR_BITS) {
if (newLSR & UART_LSR_BI)
icount->brk++;
if (newLSR & UART_LSR_OE)
icount->overrun++;
if (newLSR & UART_LSR_PE)
icount->parity++;
if (newLSR & UART_LSR_FE)
icount->frame++;
}
}
static int qt2_write_room(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct qt2_port_private *port_priv;
unsigned long flags = 0;
int r;
port_priv = usb_get_serial_port_data(port);
spin_lock_irqsave(&port_priv->urb_lock, flags);
if (port_priv->urb_in_use)
r = 0;
else
r = QT2_WRITE_BUFFER_SIZE - QT2_WRITE_CONTROL_SIZE;
spin_unlock_irqrestore(&port_priv->urb_lock, flags);
return r;
}
static int qt2_write(struct tty_struct *tty,
struct usb_serial_port *port,
const unsigned char *buf, int count)
{
struct qt2_port_private *port_priv;
struct urb *write_urb;
unsigned char *data;
unsigned long flags;
int status;
int bytes_out = 0;
port_priv = usb_get_serial_port_data(port);
if (port_priv->write_urb == NULL) {
dev_err(&port->dev, "%s - no output urb\n", __func__);
return 0;
}
write_urb = port_priv->write_urb;
count = min(count, QT2_WRITE_BUFFER_SIZE - QT2_WRITE_CONTROL_SIZE);
data = write_urb->transfer_buffer;
spin_lock_irqsave(&port_priv->urb_lock, flags);
if (port_priv->urb_in_use == true) {
dev_err(&port->dev, "qt2_write - urb is in use\n");
goto write_out;
}
*data++ = QT2_CONTROL_BYTE;
*data++ = QT2_CONTROL_BYTE;
*data++ = port_priv->device_port;
put_unaligned_le16(count, data);
data += 2;
memcpy(data, buf, count);
write_urb->transfer_buffer_length = count + QT2_WRITE_CONTROL_SIZE;
status = usb_submit_urb(write_urb, GFP_ATOMIC);
if (status == 0) {
port_priv->urb_in_use = true;
bytes_out += count;
}
write_out:
spin_unlock_irqrestore(&port_priv->urb_lock, flags);
return bytes_out;
}
static struct usb_serial_driver qt2_device = {
.driver = {
.owner = THIS_MODULE,
.name = "quatech-serial",
},
.description = DRIVER_DESC,
.id_table = id_table,
.open = qt2_open,
.close = qt2_close,
.write = qt2_write,
.write_room = qt2_write_room,
.calc_num_ports = qt2_calc_num_ports,
.attach = qt2_attach,
.release = qt2_release,
.disconnect = qt2_disconnect,
.port_probe = qt2_port_probe,
.port_remove = qt2_port_remove,
.dtr_rts = qt2_dtr_rts,
.break_ctl = qt2_break_ctl,
.tiocmget = qt2_tiocmget,
.tiocmset = qt2_tiocmset,
.tiocmiwait = usb_serial_generic_tiocmiwait,
.get_icount = usb_serial_generic_get_icount,
.ioctl = qt2_ioctl,
.set_termios = qt2_set_termios,
};
static struct usb_serial_driver *const serial_drivers[] = {
&qt2_device, NULL
};
module_usb_serial_driver(serial_drivers, id_table);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");