microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность
WSL2-Linux-Kernel/arch/arm/kvm/init.S

155 строки
4.3 KiB
ArmAsm
Исходник Обычный вид История

KVM: ARM: Initial skeleton to compile KVM support Targets KVM support for Cortex A-15 processors. Contains all the framework components, make files, header files, some tracing functionality, and basic user space API. Only supported core is Cortex-A15 for now. Most functionality is in arch/arm/kvm/* or arch/arm/include/asm/kvm_*.h. Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
/*
* Copyright (C) 2012 - Virtual Open Systems and Columbia University
* Author: Christoffer Dall <c.dall@virtualopensystems.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License, version 2, as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
#include <linux/linkage.h>
#include <asm/unified.h>
KVM: ARM: Initial skeleton to compile KVM support Targets KVM support for Cortex A-15 processors. Contains all the framework components, make files, header files, some tracing functionality, and basic user space API. Only supported core is Cortex-A15 for now. Most functionality is in arch/arm/kvm/* or arch/arm/include/asm/kvm_*.h. Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
#include <asm/asm-offsets.h>
#include <asm/kvm_asm.h>
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
#include <asm/kvm_arm.h>
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
#include <asm/kvm_mmu.h>
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
/********************************************************************
* Hypervisor initialization
* - should be called with:
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
* r0 = top of Hyp stack (kernel VA)
* r1 = pointer to hyp vectors
* r2,r3 = Hypervisor pgd pointer
*
* The init scenario is:
* - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd,
* runtime stack, runtime vectors
* - Enable the MMU with the boot pgd
* - Jump to a target into the trampoline page (remember, this is the same
* physical page!)
* - Now switch to the runtime pgd (same VA, and still the same physical
* page!)
* - Invalidate TLBs
* - Set stack and vectors
* - Profit! (or eret, if you only care about the code).
*
* As we only have four registers available to pass parameters (and we
* need six), we split the init in two phases:
* - Phase 1: r0 = 0, r1 = 0, r2,r3 contain the boot PGD.
* Provides the basic HYP init, and enable the MMU.
* - Phase 2: r0 = ToS, r1 = vectors, r2,r3 contain the runtime PGD.
* Switches to the runtime PGD, set stack and vectors.
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
*/
.text
.pushsection .hyp.idmap.text,"ax"
.align 5
__kvm_hyp_init:
.globl __kvm_hyp_init
@ Hyp-mode exception vector
W(b) .
W(b) .
W(b) .
W(b) .
W(b) .
W(b) __do_hyp_init
W(b) .
W(b) .
__do_hyp_init:
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
cmp r0, #0 @ We have a SP?
bne phase2 @ Yes, second stage init
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
@ Set the HTTBR to point to the hypervisor PGD pointer passed
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
mcrr p15, 4, r2, r3, c2
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
@ Set the HTCR and VTCR to the same shareability and cacheability
@ settings as the non-secure TTBCR and with T0SZ == 0.
mrc p15, 4, r0, c2, c0, 2 @ HTCR
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
ldr r2, =HTCR_MASK
bic r0, r0, r2
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
mrc p15, 0, r1, c2, c0, 2 @ TTBCR
and r1, r1, #(HTCR_MASK & ~TTBCR_T0SZ)
orr r0, r0, r1
mcr p15, 4, r0, c2, c0, 2 @ HTCR
mrc p15, 4, r1, c2, c1, 2 @ VTCR
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
ldr r2, =VTCR_MASK
bic r1, r1, r2
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
bic r0, r0, #(~VTCR_HTCR_SH) @ clear non-reusable HTCR bits
orr r1, r0, r1
orr r1, r1, #(KVM_VTCR_SL0 | KVM_VTCR_T0SZ | KVM_VTCR_S)
mcr p15, 4, r1, c2, c1, 2 @ VTCR
@ Use the same memory attributes for hyp. accesses as the kernel
@ (copy MAIRx ro HMAIRx).
mrc p15, 0, r0, c10, c2, 0
mcr p15, 4, r0, c10, c2, 0
mrc p15, 0, r0, c10, c2, 1
mcr p15, 4, r0, c10, c2, 1
@ Set the HSCTLR to:
@ - ARM/THUMB exceptions: Kernel config (Thumb-2 kernel)
@ - Endianness: Kernel config
@ - Fast Interrupt Features: Kernel config
@ - Write permission implies XN: disabled
@ - Instruction cache: enabled
@ - Data/Unified cache: enabled
@ - Memory alignment checks: enabled
@ - MMU: enabled (this code must be run from an identity mapping)
mrc p15, 4, r0, c1, c0, 0 @ HSCR
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
ldr r2, =HSCTLR_MASK
bic r0, r0, r2
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
mrc p15, 0, r1, c1, c0, 0 @ SCTLR
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
ldr r2, =(HSCTLR_EE | HSCTLR_FI | HSCTLR_I | HSCTLR_C)
and r1, r1, r2
ARM( ldr r2, =(HSCTLR_M | HSCTLR_A) )
THUMB( ldr r2, =(HSCTLR_M | HSCTLR_A | HSCTLR_TE) )
orr r1, r1, r2
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
orr r0, r0, r1
isb
mcr p15, 4, r0, c1, c0, 0 @ HSCR
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
@ End of init phase-1
eret
phase2:
@ Set stack pointer
mov sp, r0
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
@ Set HVBAR to point to the HYP vectors
ARM: KVM: switch to a dual-step HYP init code Our HYP init code suffers from two major design issues: - it cannot support CPU hotplug, as we tear down the idmap very early - it cannot perform a TLB invalidation when switching from init to runtime mappings, as pages are manipulated from PL1 exclusively The hotplug problem mandates that we keep two sets of page tables (boot and runtime). The TLB problem mandates that we're able to transition from one PGD to another while in HYP, invalidating the TLBs in the process. To be able to do this, we need to share a page between the two page tables. A page that will have the same VA in both configurations. All we need is a VA that has the following properties: - This VA can't be used to represent a kernel mapping. - This VA will not conflict with the physical address of the kernel text The vectors page seems to satisfy this requirement: - The kernel never maps anything else there - The kernel text being copied at the beginning of the physical memory, it is unlikely to use the last 64kB (I doubt we'll ever support KVM on a system with something like 4MB of RAM, but patches are very welcome). Let's call this VA the trampoline VA. Now, we map our init page at 3 locations: - idmap in the boot pgd - trampoline VA in the boot pgd - trampoline VA in the runtime pgd The init scenario is now the following: - We jump in HYP with four parameters: boot HYP pgd, runtime HYP pgd, runtime stack, runtime vectors - Enable the MMU with the boot pgd - Jump to a target into the trampoline page (remember, this is the same physical page!) - Now switch to the runtime pgd (same VA, and still the same physical page!) - Invalidate TLBs - Set stack and vectors - Profit! (or eret, if you only care about the code). Note that we keep the boot mapping permanently (it is not strictly an idmap anymore) to allow for CPU hotplug in later patches. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
2013-04-12 22:12:06 +04:00
mcr p15, 4, r1, c12, c0, 0 @ HVBAR
@ Jump to the trampoline page
ldr r0, =TRAMPOLINE_VA
adr r1, target
bfi r0, r1, #0, #PAGE_SHIFT
mov pc, r0
target: @ We're now in the trampoline code, switch page tables
mcrr p15, 4, r2, r3, c2
isb
@ Invalidate the old TLBs
mcr p15, 4, r0, c8, c7, 0 @ TLBIALLH
ARM: kvm: use inner-shareable barriers after TLB flushing When flushing the TLB at PL2 in response to remapping at stage-2 or VMID rollover, we have a dsb instruction to ensure completion of the command before continuing. Since we only care about other processors for TLB invalidation, use the inner-shareable variant of the dsb instruction instead. Acked-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2013-05-13 15:08:06 +04:00
dsb ish
KVM: ARM: Hypervisor initialization Sets up KVM code to handle all exceptions taken to Hyp mode. When the kernel is booted in Hyp mode, calling an hvc instruction with r0 pointing to the new vectors, the HVBAR is changed to the the vector pointers. This allows subsystems (like KVM here) to execute code in Hyp-mode with the MMU disabled. We initialize other Hyp-mode registers and enables the MMU for Hyp-mode from the id-mapped hyp initialization code. Afterwards, the HVBAR is changed to point to KVM Hyp vectors used to catch guest faults and to switch to Hyp mode to perform a world-switch into a KVM guest. Also provides memory mapping code to map required code pages, data structures, and I/O regions accessed in Hyp mode at the same virtual address as the host kernel virtual addresses, but which conforms to the architectural requirements for translations in Hyp mode. This interface is added in arch/arm/kvm/arm_mmu.c and comprises: - create_hyp_mappings(from, to); - create_hyp_io_mappings(from, to, phys_addr); - free_hyp_pmds(); Reviewed-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
2013-01-21 03:28:06 +04:00
eret
.ltorg
.globl __kvm_hyp_init_end
__kvm_hyp_init_end:
.popsection