54 строки
2.0 KiB
Plaintext
54 строки
2.0 KiB
Plaintext
|
modprobe sound
|
||
|
|
insmod uart401
|
||
|
|
insmod sb ...
|
||
|
|
|
||
|
|
This loads the driver for the Sound Blaster and assorted clones. Cards that
|
||
|
|
are covered by other drivers should not be using this driver.
|
||
|
|
|
||
|
|
The Sound Blaster module takes the following arguments
|
||
|
|
|
||
|
|
io I/O address of the Sound Blaster chip (0x220,0x240,0x260,0x280)
|
||
|
|
irq IRQ of the Sound Blaster chip (5,7,9,10)
|
||
|
|
dma 8-bit DMA channel for the Sound Blaster (0,1,3)
|
||
|
|
dma16 16-bit DMA channel for SB16 and equivalent cards (5,6,7)
|
||
|
|
mpu_io I/O for MPU chip if present (0x300,0x330)
|
||
|
|
|
||
|
|
sm_games=1 Set if you have a Logitech soundman games
|
||
|
|
acer=1 Set this to detect cards in some ACER notebooks
|
||
|
|
mwave_bug=1 Set if you are trying to use this driver with mwave (see on)
|
||
|
|
type Use this to specify a specific card type
|
||
|
|
|
||
|
|
The following arguments are taken if ISAPnP support is compiled in
|
||
|
|
|
||
|
|
isapnp=0 Set this to disable ISAPnP detection (use io=0xXXX etc. above)
|
||
|
|
multiple=0 Set to disable detection of multiple Soundblaster cards.
|
||
|
|
Consider it a bug if this option is needed, and send in a
|
||
|
|
report.
|
||
|
|
pnplegacy=1 Set this to be able to use a PnP card(s) along with a single
|
||
|
|
non-PnP (legacy) card. Above options for io, irq, etc. are
|
||
|
|
needed, and will apply only to the legacy card.
|
||
|
|
reverse=1 Reverses the order of the search in the PnP table.
|
||
|
|
uart401=1 Set to enable detection of mpu devices on some clones.
|
||
|
|
isapnpjump=n Jumps to slot n in the driver's PnP table. Use the source,
|
||
|
|
Luke.
|
||
|
|
|
||
|
|
You may well want to load the opl3 driver for synth music on most SB and
|
||
|
|
clone SB devices
|
||
|
|
|
||
|
|
insmod opl3 io=0x388
|
||
|
|
|
||
|
|
Using Mwave
|
||
|
|
|
||
|
|
To make this driver work with Mwave you must set mwave_bug. You also need
|
||
|
|
to warm boot from DOS/Windows with the required firmware loaded under this
|
||
|
|
OS. IBM are being difficult about documenting how to load this firmware.
|
||
|
|
|
||
|
|
Avance Logic ALS007
|
||
|
|
|
||
|
|
This card is supported; see the separate file ALS007 for full details.
|
||
|
|
|
||
|
|
Avance Logic ALS100
|
||
|
|
|
||
|
|
This card is supported; setup should be as for a standard Sound Blaster 16.
|
||
|
|
The driver will identify the audio device as a "Sound Blaster 16 (ALS-100)".
|