415 строки
18 KiB
ReStructuredText
415 строки
18 KiB
ReStructuredText
|
.. SPDX-License-Identifier: GPL-2.0
|
||
|
|
|
||
|
|
=======================
|
||
|
|
STM32 DMA-MDMA chaining
|
||
|
|
=======================
|
||
|
|
|
||
|
|
|
||
|
|
Introduction
|
||
|
|
------------
|
||
|
|
|
||
|
|
This document describes the STM32 DMA-MDMA chaining feature. But before going
|
||
|
|
further, let's introduce the peripherals involved.
|
||
|
|
|
||
|
|
To offload data transfers from the CPU, STM32 microprocessors (MPUs) embed
|
||
|
|
direct memory access controllers (DMA).
|
||
|
|
|
||
|
|
STM32MP1 SoCs embed both STM32 DMA and STM32 MDMA controllers. STM32 DMA
|
||
|
|
request routing capabilities are enhanced by a DMA request multiplexer
|
||
|
|
(STM32 DMAMUX).
|
||
|
|
|
||
|
|
**STM32 DMAMUX**
|
||
|
|
|
||
|
|
STM32 DMAMUX routes any DMA request from a given peripheral to any STM32 DMA
|
||
|
|
controller (STM32MP1 counts two STM32 DMA controllers) channels.
|
||
|
|
|
||
|
|
**STM32 DMA**
|
||
|
|
|
||
|
|
STM32 DMA is mainly used to implement central data buffer storage (usually in
|
||
|
|
the system SRAM) for different peripheral. It can access external RAMs but
|
||
|
|
without the ability to generate convenient burst transfer ensuring the best
|
||
|
|
load of the AXI.
|
||
|
|
|
||
|
|
**STM32 MDMA**
|
||
|
|
|
||
|
|
STM32 MDMA (Master DMA) is mainly used to manage direct data transfers between
|
||
|
|
RAM data buffers without CPU intervention. It can also be used in a
|
||
|
|
hierarchical structure that uses STM32 DMA as first level data buffer
|
||
|
|
interfaces for AHB peripherals, while the STM32 MDMA acts as a second level
|
||
|
|
DMA with better performance. As a AXI/AHB master, STM32 MDMA can take control
|
||
|
|
of the AXI/AHB bus.
|
||
|
|
|
||
|
|
|
||
|
|
Principles
|
||
|
|
----------
|
||
|
|
|
||
|
|
STM32 DMA-MDMA chaining feature relies on the strengths of STM32 DMA and
|
||
|
|
STM32 MDMA controllers.
|
||
|
|
|
||
|
|
STM32 DMA has a circular Double Buffer Mode (DBM). At each end of transaction
|
||
|
|
(when DMA data counter - DMA_SxNDTR - reaches 0), the memory pointers
|
||
|
|
(configured with DMA_SxSM0AR and DMA_SxM1AR) are swapped and the DMA data
|
||
|
|
counter is automatically reloaded. This allows the SW or the STM32 MDMA to
|
||
|
|
process one memory area while the second memory area is being filled/used by
|
||
|
|
the STM32 DMA transfer.
|
||
|
|
|
||
|
|
With STM32 MDMA linked-list mode, a single request initiates the data array
|
||
|
|
(collection of nodes) to be transferred until the linked-list pointer for the
|
||
|
|
channel is null. The channel transfer complete of the last node is the end of
|
||
|
|
transfer, unless first and last nodes are linked to each other, in such a
|
||
|
|
case, the linked-list loops on to create a circular MDMA transfer.
|
||
|
|
|
||
|
|
STM32 MDMA has direct connections with STM32 DMA. This enables autonomous
|
||
|
|
communication and synchronization between peripherals, thus saving CPU
|
||
|
|
resources and bus congestion. Transfer Complete signal of STM32 DMA channel
|
||
|
|
can triggers STM32 MDMA transfer. STM32 MDMA can clear the request generated
|
||
|
|
by the STM32 DMA by writing to its Interrupt Clear register (whose address is
|
||
|
|
stored in MDMA_CxMAR, and bit mask in MDMA_CxMDR).
|
||
|
|
|
||
|
|
.. table:: STM32 MDMA interconnect table with STM32 DMA
|
||
|
|
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| STM32 DMAMUX | STM32 DMA | STM32 DMA | STM32 MDMA |
|
||
|
|
| channels | channels | Transfer | request |
|
||
|
|
| | | complete | |
|
||
|
|
| | | signal | |
|
||
|
|
+==============+================+===========+============+
|
||
|
|
| Channel *0* | DMA1 channel 0 | dma1_tcf0 | *0x00* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *1* | DMA1 channel 1 | dma1_tcf1 | *0x01* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *2* | DMA1 channel 2 | dma1_tcf2 | *0x02* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *3* | DMA1 channel 3 | dma1_tcf3 | *0x03* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *4* | DMA1 channel 4 | dma1_tcf4 | *0x04* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *5* | DMA1 channel 5 | dma1_tcf5 | *0x05* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *6* | DMA1 channel 6 | dma1_tcf6 | *0x06* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *7* | DMA1 channel 7 | dma1_tcf7 | *0x07* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *8* | DMA2 channel 0 | dma2_tcf0 | *0x08* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *9* | DMA2 channel 1 | dma2_tcf1 | *0x09* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *10* | DMA2 channel 2 | dma2_tcf2 | *0x0A* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *11* | DMA2 channel 3 | dma2_tcf3 | *0x0B* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *12* | DMA2 channel 4 | dma2_tcf4 | *0x0C* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *13* | DMA2 channel 5 | dma2_tcf5 | *0x0D* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *14* | DMA2 channel 6 | dma2_tcf6 | *0x0E* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
| Channel *15* | DMA2 channel 7 | dma2_tcf7 | *0x0F* |
|
||
|
|
+--------------+----------------+-----------+------------+
|
||
|
|
|
||
|
|
STM32 DMA-MDMA chaining feature then uses a SRAM buffer. STM32MP1 SoCs embed
|
||
|
|
three fast access static internal RAMs of various size, used for data storage.
|
||
|
|
Due to STM32 DMA legacy (within microcontrollers), STM32 DMA performances are
|
||
|
|
bad with DDR, while they are optimal with SRAM. Hence the SRAM buffer used
|
||
|
|
between STM32 DMA and STM32 MDMA. This buffer is split in two equal periods
|
||
|
|
and STM32 DMA uses one period while STM32 MDMA uses the other period
|
||
|
|
simultaneously.
|
||
|
|
::
|
||
|
|
|
||
|
|
dma[1:2]-tcf[0:7]
|
||
|
|
.----------------.
|
||
|
|
____________ ' _________ V____________
|
||
|
|
| STM32 DMA | / __|>_ \ | STM32 MDMA |
|
||
|
|
|------------| | / \ | |------------|
|
||
|
|
| DMA_SxM0AR |<=>| | SRAM | |<=>| []-[]...[] |
|
||
|
|
| DMA_SxM1AR | | \_____/ | | |
|
||
|
|
|____________| \___<|____/ |____________|
|
||
|
|
|
||
|
|
STM32 DMA-MDMA chaining uses (struct dma_slave_config).peripheral_config to
|
||
|
|
exchange the parameters needed to configure MDMA. These parameters are
|
||
|
|
gathered into a u32 array with three values:
|
||
|
|
|
||
|
|
* the STM32 MDMA request (which is actually the DMAMUX channel ID),
|
||
|
|
* the address of the STM32 DMA register to clear the Transfer Complete
|
||
|
|
interrupt flag,
|
||
|
|
* the mask of the Transfer Complete interrupt flag of the STM32 DMA channel.
|
||
|
|
|
||
|
|
Device Tree updates for STM32 DMA-MDMA chaining support
|
||
|
|
-------------------------------------------------------
|
||
|
|
|
||
|
|
**1. Allocate a SRAM buffer**
|
||
|
|
|
||
|
|
SRAM device tree node is defined in SoC device tree. You can refer to it in
|
||
|
|
your board device tree to define your SRAM pool.
|
||
|
|
::
|
||
|
|
|
||
|
|
&sram {
|
||
|
|
my_foo_device_dma_pool: dma-sram@0 {
|
||
|
|
reg = <0x0 0x1000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
Be careful of the start index, in case there are other SRAM consumers.
|
||
|
|
Define your pool size strategically: to optimise chaining, the idea is that
|
||
|
|
STM32 DMA and STM32 MDMA can work simultaneously, on each buffer of the
|
||
|
|
SRAM.
|
||
|
|
If the SRAM period is greater than the expected DMA transfer, then STM32 DMA
|
||
|
|
and STM32 MDMA will work sequentially instead of simultaneously. It is not a
|
||
|
|
functional issue but it is not optimal.
|
||
|
|
|
||
|
|
Don't forget to refer to your SRAM pool in your device node. You need to
|
||
|
|
define a new property.
|
||
|
|
::
|
||
|
|
|
||
|
|
&my_foo_device {
|
||
|
|
...
|
||
|
|
my_dma_pool = &my_foo_device_dma_pool;
|
||
|
|
};
|
||
|
|
|
||
|
|
Then get this SRAM pool in your foo driver and allocate your SRAM buffer.
|
||
|
|
|
||
|
|
**2. Allocate a STM32 DMA channel and a STM32 MDMA channel**
|
||
|
|
|
||
|
|
You need to define an extra channel in your device tree node, in addition to
|
||
|
|
the one you should already have for "classic" DMA operation.
|
||
|
|
|
||
|
|
This new channel must be taken from STM32 MDMA channels, so, the phandle of
|
||
|
|
the DMA controller to use is the MDMA controller's one.
|
||
|
|
::
|
||
|
|
|
||
|
|
&my_foo_device {
|
||
|
|
[...]
|
||
|
|
my_dma_pool = &my_foo_device_dma_pool;
|
||
|
|
dmas = <&dmamux1 ...>, // STM32 DMA channel
|
||
|
|
<&mdma1 0 0x3 0x1200000a 0 0>; // + STM32 MDMA channel
|
||
|
|
};
|
||
|
|
|
||
|
|
Concerning STM32 MDMA bindings:
|
||
|
|
|
||
|
|
1. The request line number : whatever the value here, it will be overwritten
|
||
|
|
by MDMA driver with the STM32 DMAMUX channel ID passed through
|
||
|
|
(struct dma_slave_config).peripheral_config
|
||
|
|
|
||
|
|
2. The priority level : choose Very High (0x3) so that your channel will
|
||
|
|
take priority other the other during request arbitration
|
||
|
|
|
||
|
|
3. A 32bit mask specifying the DMA channel configuration : source and
|
||
|
|
destination address increment, block transfer with 128 bytes per single
|
||
|
|
transfer
|
||
|
|
|
||
|
|
4. The 32bit value specifying the register to be used to acknowledge the
|
||
|
|
request: it will be overwritten by MDMA driver, with the DMA channel
|
||
|
|
interrupt flag clear register address passed through
|
||
|
|
(struct dma_slave_config).peripheral_config
|
||
|
|
|
||
|
|
5. The 32bit mask specifying the value to be written to acknowledge the
|
||
|
|
request: it will be overwritten by MDMA driver, with the DMA channel
|
||
|
|
Transfer Complete flag passed through
|
||
|
|
(struct dma_slave_config).peripheral_config
|
||
|
|
|
||
|
|
Driver updates for STM32 DMA-MDMA chaining support in foo driver
|
||
|
|
----------------------------------------------------------------
|
||
|
|
|
||
|
|
**0. (optional) Refactor the original sg_table if dmaengine_prep_slave_sg()**
|
||
|
|
|
||
|
|
In case of dmaengine_prep_slave_sg(), the original sg_table can't be used as
|
||
|
|
is. Two new sg_tables must be created from the original one. One for
|
||
|
|
STM32 DMA transfer (where memory address targets now the SRAM buffer instead
|
||
|
|
of DDR buffer) and one for STM32 MDMA transfer (where memory address targets
|
||
|
|
the DDR buffer).
|
||
|
|
|
||
|
|
The new sg_list items must fit SRAM period length. Here is an example for
|
||
|
|
DMA_DEV_TO_MEM:
|
||
|
|
::
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Assuming sgl and nents, respectively the initial scatterlist and its
|
||
|
|
* length.
|
||
|
|
* Assuming sram_dma_buf and sram_period, respectively the memory
|
||
|
|
* allocated from the pool for DMA usage, and the length of the period,
|
||
|
|
* which is half of the sram_buf size.
|
||
|
|
*/
|
||
|
|
struct sg_table new_dma_sgt, new_mdma_sgt;
|
||
|
|
struct scatterlist *s, *_sgl;
|
||
|
|
dma_addr_t ddr_dma_buf;
|
||
|
|
u32 new_nents = 0, len;
|
||
|
|
int i;
|
||
|
|
|
||
|
|
/* Count the number of entries needed */
|
||
|
|
for_each_sg(sgl, s, nents, i)
|
||
|
|
if (sg_dma_len(s) > sram_period)
|
||
|
|
new_nents += DIV_ROUND_UP(sg_dma_len(s), sram_period);
|
||
|
|
else
|
||
|
|
new_nents++;
|
||
|
|
|
||
|
|
/* Create sg table for STM32 DMA channel */
|
||
|
|
ret = sg_alloc_table(&new_dma_sgt, new_nents, GFP_ATOMIC);
|
||
|
|
if (ret)
|
||
|
|
dev_err(dev, "DMA sg table alloc failed\n");
|
||
|
|
|
||
|
|
for_each_sg(new_dma_sgt.sgl, s, new_dma_sgt.nents, i) {
|
||
|
|
_sgl = sgl;
|
||
|
|
sg_dma_len(s) = min(sg_dma_len(_sgl), sram_period);
|
||
|
|
/* Targets the beginning = first half of the sram_buf */
|
||
|
|
s->dma_address = sram_buf;
|
||
|
|
/*
|
||
|
|
* Targets the second half of the sram_buf
|
||
|
|
* for odd indexes of the item of the sg_list
|
||
|
|
*/
|
||
|
|
if (i & 1)
|
||
|
|
s->dma_address += sram_period;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* Create sg table for STM32 MDMA channel */
|
||
|
|
ret = sg_alloc_table(&new_mdma_sgt, new_nents, GFP_ATOMIC);
|
||
|
|
if (ret)
|
||
|
|
dev_err(dev, "MDMA sg_table alloc failed\n");
|
||
|
|
|
||
|
|
_sgl = sgl;
|
||
|
|
len = sg_dma_len(sgl);
|
||
|
|
ddr_dma_buf = sg_dma_address(sgl);
|
||
|
|
for_each_sg(mdma_sgt.sgl, s, mdma_sgt.nents, i) {
|
||
|
|
size_t bytes = min_t(size_t, len, sram_period);
|
||
|
|
|
||
|
|
sg_dma_len(s) = bytes;
|
||
|
|
sg_dma_address(s) = ddr_dma_buf;
|
||
|
|
len -= bytes;
|
||
|
|
|
||
|
|
if (!len && sg_next(_sgl)) {
|
||
|
|
_sgl = sg_next(_sgl);
|
||
|
|
len = sg_dma_len(_sgl);
|
||
|
|
ddr_dma_buf = sg_dma_address(_sgl);
|
||
|
|
} else {
|
||
|
|
ddr_dma_buf += bytes;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
Don't forget to release these new sg_tables after getting the descriptors
|
||
|
|
with dmaengine_prep_slave_sg().
|
||
|
|
|
||
|
|
**1. Set controller specific parameters**
|
||
|
|
|
||
|
|
First, use dmaengine_slave_config() with a struct dma_slave_config to
|
||
|
|
configure STM32 DMA channel. You just have to take care of DMA addresses,
|
||
|
|
the memory address (depending on the transfer direction) must point on your
|
||
|
|
SRAM buffer, and set (struct dma_slave_config).peripheral_size != 0.
|
||
|
|
|
||
|
|
STM32 DMA driver will check (struct dma_slave_config).peripheral_size to
|
||
|
|
determine if chaining is being used or not. If it is used, then STM32 DMA
|
||
|
|
driver fills (struct dma_slave_config).peripheral_config with an array of
|
||
|
|
three u32 : the first one containing STM32 DMAMUX channel ID, the second one
|
||
|
|
the channel interrupt flag clear register address, and the third one the
|
||
|
|
channel Transfer Complete flag mask.
|
||
|
|
|
||
|
|
Then, use dmaengine_slave_config with another struct dma_slave_config to
|
||
|
|
configure STM32 MDMA channel. Take care of DMA addresses, the device address
|
||
|
|
(depending on the transfer direction) must point on your SRAM buffer, and
|
||
|
|
the memory address must point to the buffer originally used for "classic"
|
||
|
|
DMA operation. Use the previous (struct dma_slave_config).peripheral_size
|
||
|
|
and .peripheral_config that have been updated by STM32 DMA driver, to set
|
||
|
|
(struct dma_slave_config).peripheral_size and .peripheral_config of the
|
||
|
|
struct dma_slave_config to configure STM32 MDMA channel.
|
||
|
|
::
|
||
|
|
|
||
|
|
struct dma_slave_config dma_conf;
|
||
|
|
struct dma_slave_config mdma_conf;
|
||
|
|
|
||
|
|
memset(&dma_conf, 0, sizeof(dma_conf));
|
||
|
|
[...]
|
||
|
|
config.direction = DMA_DEV_TO_MEM;
|
||
|
|
config.dst_addr = sram_dma_buf; // SRAM buffer
|
||
|
|
config.peripheral_size = 1; // peripheral_size != 0 => chaining
|
||
|
|
|
||
|
|
dmaengine_slave_config(dma_chan, &dma_config);
|
||
|
|
|
||
|
|
memset(&mdma_conf, 0, sizeof(mdma_conf));
|
||
|
|
config.direction = DMA_DEV_TO_MEM;
|
||
|
|
mdma_conf.src_addr = sram_dma_buf; // SRAM buffer
|
||
|
|
mdma_conf.dst_addr = rx_dma_buf; // original memory buffer
|
||
|
|
mdma_conf.peripheral_size = dma_conf.peripheral_size; // <- dma_conf
|
||
|
|
mdma_conf.peripheral_config = dma_config.peripheral_config; // <- dma_conf
|
||
|
|
|
||
|
|
dmaengine_slave_config(mdma_chan, &mdma_conf);
|
||
|
|
|
||
|
|
**2. Get a descriptor for STM32 DMA channel transaction**
|
||
|
|
|
||
|
|
In the same way you get your descriptor for your "classic" DMA operation,
|
||
|
|
you just have to replace the original sg_list (in case of
|
||
|
|
dmaengine_prep_slave_sg()) with the new sg_list using SRAM buffer, or to
|
||
|
|
replace the original buffer address, length and period (in case of
|
||
|
|
dmaengine_prep_dma_cyclic()) with the new SRAM buffer.
|
||
|
|
|
||
|
|
**3. Get a descriptor for STM32 MDMA channel transaction**
|
||
|
|
|
||
|
|
If you previously get descriptor (for STM32 DMA) with
|
||
|
|
|
||
|
|
* dmaengine_prep_slave_sg(), then use dmaengine_prep_slave_sg() for
|
||
|
|
STM32 MDMA;
|
||
|
|
* dmaengine_prep_dma_cyclic(), then use dmaengine_prep_dma_cyclic() for
|
||
|
|
STM32 MDMA.
|
||
|
|
|
||
|
|
Use the new sg_list using SRAM buffer (in case of dmaengine_prep_slave_sg())
|
||
|
|
or, depending on the transfer direction, either the original DDR buffer (in
|
||
|
|
case of DMA_DEV_TO_MEM) or the SRAM buffer (in case of DMA_MEM_TO_DEV), the
|
||
|
|
source address being previously set with dmaengine_slave_config().
|
||
|
|
|
||
|
|
**4. Submit both transactions**
|
||
|
|
|
||
|
|
Before submitting your transactions, you may need to define on which
|
||
|
|
descriptor you want a callback to be called at the end of the transfer
|
||
|
|
(dmaengine_prep_slave_sg()) or the period (dmaengine_prep_dma_cyclic()).
|
||
|
|
Depending on the direction, set the callback on the descriptor that finishes
|
||
|
|
the overal transfer:
|
||
|
|
|
||
|
|
* DMA_DEV_TO_MEM: set the callback on the "MDMA" descriptor
|
||
|
|
* DMA_MEM_TO_DEV: set the callback on the "DMA" descriptor
|
||
|
|
|
||
|
|
Then, submit the descriptors whatever the order, with dmaengine_tx_submit().
|
||
|
|
|
||
|
|
**5. Issue pending requests (and wait for callback notification)**
|
||
|
|
|
||
|
|
As STM32 MDMA channel transfer is triggered by STM32 DMA, you must issue
|
||
|
|
STM32 MDMA channel before STM32 DMA channel.
|
||
|
|
|
||
|
|
If any, your callback will be called to warn you about the end of the overal
|
||
|
|
transfer or the period completion.
|
||
|
|
|
||
|
|
Don't forget to terminate both channels. STM32 DMA channel is configured in
|
||
|
|
cyclic Double-Buffer mode so it won't be disabled by HW, you need to terminate
|
||
|
|
it. STM32 MDMA channel will be stopped by HW in case of sg transfer, but not
|
||
|
|
in case of cyclic transfer. You can terminate it whatever the kind of transfer.
|
||
|
|
|
||
|
|
**STM32 DMA-MDMA chaining DMA_MEM_TO_DEV special case**
|
||
|
|
|
||
|
|
STM32 DMA-MDMA chaining in DMA_MEM_TO_DEV is a special case. Indeed, the
|
||
|
|
STM32 MDMA feeds the SRAM buffer with the DDR data, and the STM32 DMA reads
|
||
|
|
data from SRAM buffer. So some data (the first period) have to be copied in
|
||
|
|
SRAM buffer when the STM32 DMA starts to read.
|
||
|
|
|
||
|
|
A trick could be pausing the STM32 DMA channel (that will raise a Transfer
|
||
|
|
Complete signal, triggering the STM32 MDMA channel), but the first data read
|
||
|
|
by the STM32 DMA could be "wrong". The proper way is to prepare the first SRAM
|
||
|
|
period with dmaengine_prep_dma_memcpy(). Then this first period should be
|
||
|
|
"removed" from the sg or the cyclic transfer.
|
||
|
|
|
||
|
|
Due to this complexity, rather use the STM32 DMA-MDMA chaining for
|
||
|
|
DMA_DEV_TO_MEM and keep the "classic" DMA usage for DMA_MEM_TO_DEV, unless
|
||
|
|
you're not afraid.
|
||
|
|
|
||
|
|
Resources
|
||
|
|
---------
|
||
|
|
|
||
|
|
Application note, datasheet and reference manual are available on ST website
|
||
|
|
(STM32MP1_).
|
||
|
|
|
||
|
|
Dedicated focus on three application notes (AN5224_, AN4031_ & AN5001_)
|
||
|
|
dealing with STM32 DMAMUX, STM32 DMA and STM32 MDMA.
|
||
|
|
|
||
|
|
.. _STM32MP1: https://www.st.com/en/microcontrollers-microprocessors/stm32mp1-series.html
|
||
|
|
.. _AN5224: https://www.st.com/resource/en/application_note/an5224-stm32-dmamux-the-dma-request-router-stmicroelectronics.pdf
|
||
|
|
.. _AN4031: https://www.st.com/resource/en/application_note/dm00046011-using-the-stm32f2-stm32f4-and-stm32f7-series-dma-controller-stmicroelectronics.pdf
|
||
|
|
.. _AN5001: https://www.st.com/resource/en/application_note/an5001-stm32cube-expansion-package-for-stm32h7-series-mdma-stmicroelectronics.pdf
|
||
|
|
|
||
|
|
:Authors:
|
||
|
|
|
||
|
|
- Amelie Delaunay <amelie.delaunay@foss.st.com>
|