[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
/* ir-mce_kbd-decoder.c - A decoder for the RC6-ish keyboard/mouse IR protocol
|
|
|
|
* used by the Microsoft Remote Keyboard for Windows Media Center Edition,
|
|
|
|
* referred to by Microsoft's Windows Media Center remote specification docs
|
|
|
|
* as "an internal protocol called MCIR-2".
|
|
|
|
*
|
|
|
|
* Copyright (C) 2011 by Jarod Wilson <jarod@redhat.com>
|
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
* the Free Software Foundation version 2 of the License.
|
|
|
|
*
|
|
|
|
* This program is distributed in the hope that it will be useful,
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
*/
|
2011-07-29 09:41:45 +04:00
|
|
|
#include <linux/module.h>
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
|
|
|
|
#include "rc-core-priv.h"
|
|
|
|
|
|
|
|
/*
|
|
|
|
* This decoder currently supports:
|
|
|
|
* - MCIR-2 29-bit IR signals used for mouse movement and buttons
|
|
|
|
* - MCIR-2 32-bit IR signals used for standard keyboard keys
|
|
|
|
*
|
2017-02-12 01:33:38 +03:00
|
|
|
* The media keys on the keyboard send RC-6 signals that are indistinguishable
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
* from the keys of the same name on the stock MCE remote, and will be handled
|
|
|
|
* by the standard RC-6 decoder, and be made available to the system via the
|
|
|
|
* input device for the remote, rather than the keyboard/mouse one.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#define MCIR2_UNIT 333333 /* ns */
|
|
|
|
#define MCIR2_HEADER_NBITS 5
|
|
|
|
#define MCIR2_MOUSE_NBITS 29
|
|
|
|
#define MCIR2_KEYBOARD_NBITS 32
|
|
|
|
#define MCIR2_PREFIX_PULSE (8 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_PREFIX_SPACE (1 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_MAX_LEN (3 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_BIT_START (1 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_BIT_END (1 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_BIT_0 (1 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_BIT_SET (2 * MCIR2_UNIT)
|
|
|
|
#define MCIR2_MODE_MASK 0xf /* for the header bits */
|
|
|
|
#define MCIR2_KEYBOARD_HEADER 0x4
|
|
|
|
#define MCIR2_MOUSE_HEADER 0x1
|
|
|
|
#define MCIR2_MASK_KEYS_START 0xe0
|
|
|
|
|
|
|
|
enum mce_kbd_mode {
|
|
|
|
MCIR2_MODE_KEYBOARD,
|
|
|
|
MCIR2_MODE_MOUSE,
|
|
|
|
MCIR2_MODE_UNKNOWN,
|
|
|
|
};
|
|
|
|
|
|
|
|
enum mce_kbd_state {
|
|
|
|
STATE_INACTIVE,
|
|
|
|
STATE_HEADER_BIT_START,
|
|
|
|
STATE_HEADER_BIT_END,
|
|
|
|
STATE_BODY_BIT_START,
|
|
|
|
STATE_BODY_BIT_END,
|
|
|
|
STATE_FINISHED,
|
|
|
|
};
|
|
|
|
|
|
|
|
static unsigned char kbd_keycodes[256] = {
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_A,
|
|
|
|
KEY_B, KEY_C, KEY_D, KEY_E, KEY_F,
|
|
|
|
KEY_G, KEY_H, KEY_I, KEY_J, KEY_K,
|
|
|
|
KEY_L, KEY_M, KEY_N, KEY_O, KEY_P,
|
|
|
|
KEY_Q, KEY_R, KEY_S, KEY_T, KEY_U,
|
|
|
|
KEY_V, KEY_W, KEY_X, KEY_Y, KEY_Z,
|
|
|
|
KEY_1, KEY_2, KEY_3, KEY_4, KEY_5,
|
|
|
|
KEY_6, KEY_7, KEY_8, KEY_9, KEY_0,
|
|
|
|
KEY_ENTER, KEY_ESC, KEY_BACKSPACE, KEY_TAB, KEY_SPACE,
|
|
|
|
KEY_MINUS, KEY_EQUAL, KEY_LEFTBRACE, KEY_RIGHTBRACE, KEY_BACKSLASH,
|
2017-02-02 19:20:36 +03:00
|
|
|
KEY_BACKSLASH, KEY_SEMICOLON, KEY_APOSTROPHE, KEY_GRAVE, KEY_COMMA,
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
KEY_DOT, KEY_SLASH, KEY_CAPSLOCK, KEY_F1, KEY_F2,
|
|
|
|
KEY_F3, KEY_F4, KEY_F5, KEY_F6, KEY_F7,
|
|
|
|
KEY_F8, KEY_F9, KEY_F10, KEY_F11, KEY_F12,
|
|
|
|
KEY_SYSRQ, KEY_SCROLLLOCK, KEY_PAUSE, KEY_INSERT, KEY_HOME,
|
|
|
|
KEY_PAGEUP, KEY_DELETE, KEY_END, KEY_PAGEDOWN, KEY_RIGHT,
|
|
|
|
KEY_LEFT, KEY_DOWN, KEY_UP, KEY_NUMLOCK, KEY_KPSLASH,
|
|
|
|
KEY_KPASTERISK, KEY_KPMINUS, KEY_KPPLUS, KEY_KPENTER, KEY_KP1,
|
|
|
|
KEY_KP2, KEY_KP3, KEY_KP4, KEY_KP5, KEY_KP6,
|
|
|
|
KEY_KP7, KEY_KP8, KEY_KP9, KEY_KP0, KEY_KPDOT,
|
|
|
|
KEY_102ND, KEY_COMPOSE, KEY_POWER, KEY_KPEQUAL, KEY_F13,
|
|
|
|
KEY_F14, KEY_F15, KEY_F16, KEY_F17, KEY_F18,
|
|
|
|
KEY_F19, KEY_F20, KEY_F21, KEY_F22, KEY_F23,
|
|
|
|
KEY_F24, KEY_OPEN, KEY_HELP, KEY_PROPS, KEY_FRONT,
|
|
|
|
KEY_STOP, KEY_AGAIN, KEY_UNDO, KEY_CUT, KEY_COPY,
|
|
|
|
KEY_PASTE, KEY_FIND, KEY_MUTE, KEY_VOLUMEUP, KEY_VOLUMEDOWN,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_KPCOMMA, KEY_RESERVED,
|
|
|
|
KEY_RO, KEY_KATAKANAHIRAGANA, KEY_YEN, KEY_HENKAN, KEY_MUHENKAN,
|
|
|
|
KEY_KPJPCOMMA, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_HANGUEL,
|
|
|
|
KEY_HANJA, KEY_KATAKANA, KEY_HIRAGANA, KEY_ZENKAKUHANKAKU, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_LEFTCTRL,
|
|
|
|
KEY_LEFTSHIFT, KEY_LEFTALT, KEY_LEFTMETA, KEY_RIGHTCTRL, KEY_RIGHTSHIFT,
|
|
|
|
KEY_RIGHTALT, KEY_RIGHTMETA, KEY_PLAYPAUSE, KEY_STOPCD, KEY_PREVIOUSSONG,
|
|
|
|
KEY_NEXTSONG, KEY_EJECTCD, KEY_VOLUMEUP, KEY_VOLUMEDOWN, KEY_MUTE,
|
|
|
|
KEY_WWW, KEY_BACK, KEY_FORWARD, KEY_STOP, KEY_FIND,
|
|
|
|
KEY_SCROLLUP, KEY_SCROLLDOWN, KEY_EDIT, KEY_SLEEP, KEY_COFFEE,
|
|
|
|
KEY_REFRESH, KEY_CALC, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
|
|
|
|
KEY_RESERVED
|
|
|
|
};
|
|
|
|
|
2017-10-24 18:23:14 +03:00
|
|
|
static void mce_kbd_rx_timeout(struct timer_list *t)
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
{
|
2017-10-24 18:23:14 +03:00
|
|
|
struct mce_kbd_dec *mce_kbd = from_timer(mce_kbd, t, rx_timeout);
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
int i;
|
|
|
|
unsigned char maskcode;
|
|
|
|
|
|
|
|
IR_dprintk(2, "timer callback clearing all keys\n");
|
|
|
|
|
|
|
|
for (i = 0; i < 7; i++) {
|
|
|
|
maskcode = kbd_keycodes[MCIR2_MASK_KEYS_START + i];
|
|
|
|
input_report_key(mce_kbd->idev, maskcode, 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
for (i = 0; i < MCIR2_MASK_KEYS_START; i++)
|
|
|
|
input_report_key(mce_kbd->idev, kbd_keycodes[i], 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
static enum mce_kbd_mode mce_kbd_mode(struct mce_kbd_dec *data)
|
|
|
|
{
|
|
|
|
switch (data->header & MCIR2_MODE_MASK) {
|
|
|
|
case MCIR2_KEYBOARD_HEADER:
|
|
|
|
return MCIR2_MODE_KEYBOARD;
|
|
|
|
case MCIR2_MOUSE_HEADER:
|
|
|
|
return MCIR2_MODE_MOUSE;
|
|
|
|
default:
|
|
|
|
return MCIR2_MODE_UNKNOWN;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
static void ir_mce_kbd_process_keyboard_data(struct input_dev *idev,
|
|
|
|
u32 scancode)
|
|
|
|
{
|
|
|
|
u8 keydata = (scancode >> 8) & 0xff;
|
|
|
|
u8 shiftmask = scancode & 0xff;
|
|
|
|
unsigned char keycode, maskcode;
|
|
|
|
int i, keystate;
|
|
|
|
|
|
|
|
IR_dprintk(1, "keyboard: keydata = 0x%02x, shiftmask = 0x%02x\n",
|
|
|
|
keydata, shiftmask);
|
|
|
|
|
|
|
|
for (i = 0; i < 7; i++) {
|
|
|
|
maskcode = kbd_keycodes[MCIR2_MASK_KEYS_START + i];
|
|
|
|
if (shiftmask & (1 << i))
|
|
|
|
keystate = 1;
|
|
|
|
else
|
|
|
|
keystate = 0;
|
|
|
|
input_report_key(idev, maskcode, keystate);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (keydata) {
|
|
|
|
keycode = kbd_keycodes[keydata];
|
|
|
|
input_report_key(idev, keycode, 1);
|
|
|
|
} else {
|
|
|
|
for (i = 0; i < MCIR2_MASK_KEYS_START; i++)
|
|
|
|
input_report_key(idev, kbd_keycodes[i], 0);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
static void ir_mce_kbd_process_mouse_data(struct input_dev *idev, u32 scancode)
|
|
|
|
{
|
|
|
|
/* raw mouse coordinates */
|
|
|
|
u8 xdata = (scancode >> 7) & 0x7f;
|
|
|
|
u8 ydata = (scancode >> 14) & 0x7f;
|
|
|
|
int x, y;
|
|
|
|
/* mouse buttons */
|
|
|
|
bool right = scancode & 0x40;
|
|
|
|
bool left = scancode & 0x20;
|
|
|
|
|
|
|
|
if (xdata & 0x40)
|
|
|
|
x = -((~xdata & 0x7f) + 1);
|
|
|
|
else
|
|
|
|
x = xdata;
|
|
|
|
|
|
|
|
if (ydata & 0x40)
|
|
|
|
y = -((~ydata & 0x7f) + 1);
|
|
|
|
else
|
|
|
|
y = ydata;
|
|
|
|
|
|
|
|
IR_dprintk(1, "mouse: x = %d, y = %d, btns = %s%s\n",
|
|
|
|
x, y, left ? "L" : "", right ? "R" : "");
|
|
|
|
|
|
|
|
input_report_rel(idev, REL_X, x);
|
|
|
|
input_report_rel(idev, REL_Y, y);
|
|
|
|
|
|
|
|
input_report_key(idev, BTN_LEFT, left);
|
|
|
|
input_report_key(idev, BTN_RIGHT, right);
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* ir_mce_kbd_decode() - Decode one mce_kbd pulse or space
|
|
|
|
* @dev: the struct rc_dev descriptor of the device
|
|
|
|
* @ev: the struct ir_raw_event descriptor of the pulse/space
|
|
|
|
*
|
|
|
|
* This function returns -EINVAL if the pulse violates the state machine
|
|
|
|
*/
|
|
|
|
static int ir_mce_kbd_decode(struct rc_dev *dev, struct ir_raw_event ev)
|
|
|
|
{
|
|
|
|
struct mce_kbd_dec *data = &dev->raw->mce_kbd;
|
|
|
|
u32 scancode;
|
|
|
|
unsigned long delay;
|
media: lirc: implement reading scancode
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-02-25 14:51:32 +03:00
|
|
|
struct lirc_scancode lsc = {};
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
|
|
|
|
if (!is_timing_event(ev)) {
|
|
|
|
if (ev.reset)
|
|
|
|
data->state = STATE_INACTIVE;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (!geq_margin(ev.duration, MCIR2_UNIT, MCIR2_UNIT / 2))
|
|
|
|
goto out;
|
|
|
|
|
|
|
|
again:
|
|
|
|
IR_dprintk(2, "started at state %i (%uus %s)\n",
|
|
|
|
data->state, TO_US(ev.duration), TO_STR(ev.pulse));
|
|
|
|
|
|
|
|
if (!geq_margin(ev.duration, MCIR2_UNIT, MCIR2_UNIT / 2))
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
switch (data->state) {
|
|
|
|
|
|
|
|
case STATE_INACTIVE:
|
|
|
|
if (!ev.pulse)
|
|
|
|
break;
|
|
|
|
|
|
|
|
/* Note: larger margin on first pulse since each MCIR2_UNIT
|
|
|
|
is quite short and some hardware takes some time to
|
|
|
|
adjust to the signal */
|
|
|
|
if (!eq_margin(ev.duration, MCIR2_PREFIX_PULSE, MCIR2_UNIT))
|
|
|
|
break;
|
|
|
|
|
|
|
|
data->state = STATE_HEADER_BIT_START;
|
|
|
|
data->count = 0;
|
|
|
|
data->header = 0;
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
case STATE_HEADER_BIT_START:
|
|
|
|
if (geq_margin(ev.duration, MCIR2_MAX_LEN, MCIR2_UNIT / 2))
|
|
|
|
break;
|
|
|
|
|
|
|
|
data->header <<= 1;
|
|
|
|
if (ev.pulse)
|
|
|
|
data->header |= 1;
|
|
|
|
data->count++;
|
|
|
|
data->state = STATE_HEADER_BIT_END;
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
case STATE_HEADER_BIT_END:
|
|
|
|
if (!is_transition(&ev, &dev->raw->prev_ev))
|
|
|
|
break;
|
|
|
|
|
|
|
|
decrease_duration(&ev, MCIR2_BIT_END);
|
|
|
|
|
|
|
|
if (data->count != MCIR2_HEADER_NBITS) {
|
|
|
|
data->state = STATE_HEADER_BIT_START;
|
|
|
|
goto again;
|
|
|
|
}
|
|
|
|
|
|
|
|
switch (mce_kbd_mode(data)) {
|
|
|
|
case MCIR2_MODE_KEYBOARD:
|
|
|
|
data->wanted_bits = MCIR2_KEYBOARD_NBITS;
|
|
|
|
break;
|
|
|
|
case MCIR2_MODE_MOUSE:
|
|
|
|
data->wanted_bits = MCIR2_MOUSE_NBITS;
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
IR_dprintk(1, "not keyboard or mouse data\n");
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
data->count = 0;
|
|
|
|
data->body = 0;
|
|
|
|
data->state = STATE_BODY_BIT_START;
|
|
|
|
goto again;
|
|
|
|
|
|
|
|
case STATE_BODY_BIT_START:
|
|
|
|
if (geq_margin(ev.duration, MCIR2_MAX_LEN, MCIR2_UNIT / 2))
|
|
|
|
break;
|
|
|
|
|
|
|
|
data->body <<= 1;
|
|
|
|
if (ev.pulse)
|
|
|
|
data->body |= 1;
|
|
|
|
data->count++;
|
|
|
|
data->state = STATE_BODY_BIT_END;
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
case STATE_BODY_BIT_END:
|
|
|
|
if (!is_transition(&ev, &dev->raw->prev_ev))
|
|
|
|
break;
|
|
|
|
|
|
|
|
if (data->count == data->wanted_bits)
|
|
|
|
data->state = STATE_FINISHED;
|
|
|
|
else
|
|
|
|
data->state = STATE_BODY_BIT_START;
|
|
|
|
|
|
|
|
decrease_duration(&ev, MCIR2_BIT_END);
|
|
|
|
goto again;
|
|
|
|
|
|
|
|
case STATE_FINISHED:
|
|
|
|
if (ev.pulse)
|
|
|
|
break;
|
|
|
|
|
|
|
|
switch (data->wanted_bits) {
|
|
|
|
case MCIR2_KEYBOARD_NBITS:
|
|
|
|
scancode = data->body & 0xffff;
|
|
|
|
IR_dprintk(1, "keyboard data 0x%08x\n", data->body);
|
|
|
|
if (dev->timeout)
|
|
|
|
delay = usecs_to_jiffies(dev->timeout / 1000);
|
|
|
|
else
|
|
|
|
delay = msecs_to_jiffies(100);
|
|
|
|
mod_timer(&data->rx_timeout, jiffies + delay);
|
|
|
|
/* Pass data to keyboard buffer parser */
|
|
|
|
ir_mce_kbd_process_keyboard_data(data->idev, scancode);
|
media: lirc: implement reading scancode
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-02-25 14:51:32 +03:00
|
|
|
lsc.rc_proto = RC_PROTO_MCIR2_KBD;
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
break;
|
|
|
|
case MCIR2_MOUSE_NBITS:
|
|
|
|
scancode = data->body & 0x1fffff;
|
|
|
|
IR_dprintk(1, "mouse data 0x%06x\n", scancode);
|
|
|
|
/* Pass data to mouse buffer parser */
|
|
|
|
ir_mce_kbd_process_mouse_data(data->idev, scancode);
|
media: lirc: implement reading scancode
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-02-25 14:51:32 +03:00
|
|
|
lsc.rc_proto = RC_PROTO_MCIR2_MSE;
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
break;
|
|
|
|
default:
|
|
|
|
IR_dprintk(1, "not keyboard or mouse data\n");
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
media: lirc: implement reading scancode
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-02-25 14:51:32 +03:00
|
|
|
lsc.scancode = scancode;
|
|
|
|
ir_lirc_scancode_event(dev, &lsc);
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
data->state = STATE_INACTIVE;
|
2017-02-12 01:33:38 +03:00
|
|
|
input_event(data->idev, EV_MSC, MSC_SCAN, scancode);
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
input_sync(data->idev);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
out:
|
|
|
|
IR_dprintk(1, "failed at state %i (%uus %s)\n",
|
|
|
|
data->state, TO_US(ev.duration), TO_STR(ev.pulse));
|
|
|
|
data->state = STATE_INACTIVE;
|
|
|
|
input_sync(data->idev);
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ir_mce_kbd_register(struct rc_dev *dev)
|
|
|
|
{
|
|
|
|
struct mce_kbd_dec *mce_kbd = &dev->raw->mce_kbd;
|
|
|
|
struct input_dev *idev;
|
|
|
|
int i, ret;
|
|
|
|
|
|
|
|
idev = input_allocate_device();
|
|
|
|
if (!idev)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
snprintf(mce_kbd->name, sizeof(mce_kbd->name),
|
|
|
|
"MCE IR Keyboard/Mouse (%s)", dev->driver_name);
|
|
|
|
strlcat(mce_kbd->phys, "/input0", sizeof(mce_kbd->phys));
|
|
|
|
|
|
|
|
idev->name = mce_kbd->name;
|
|
|
|
idev->phys = mce_kbd->phys;
|
|
|
|
|
|
|
|
/* Keyboard bits */
|
|
|
|
set_bit(EV_KEY, idev->evbit);
|
|
|
|
set_bit(EV_REP, idev->evbit);
|
|
|
|
for (i = 0; i < sizeof(kbd_keycodes); i++)
|
|
|
|
set_bit(kbd_keycodes[i], idev->keybit);
|
|
|
|
|
|
|
|
/* Mouse bits */
|
|
|
|
set_bit(EV_REL, idev->evbit);
|
|
|
|
set_bit(REL_X, idev->relbit);
|
|
|
|
set_bit(REL_Y, idev->relbit);
|
|
|
|
set_bit(BTN_LEFT, idev->keybit);
|
|
|
|
set_bit(BTN_RIGHT, idev->keybit);
|
|
|
|
|
|
|
|
/* Report scancodes too */
|
|
|
|
set_bit(EV_MSC, idev->evbit);
|
|
|
|
set_bit(MSC_SCAN, idev->mscbit);
|
|
|
|
|
2017-10-24 18:23:14 +03:00
|
|
|
timer_setup(&mce_kbd->rx_timeout, mce_kbd_rx_timeout, 0);
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
|
|
|
|
input_set_drvdata(idev, mce_kbd);
|
|
|
|
|
|
|
|
#if 0
|
|
|
|
/* Adding this reference means two input devices are associated with
|
|
|
|
* this rc-core device, which ir-keytable doesn't cope with yet */
|
|
|
|
idev->dev.parent = &dev->dev;
|
|
|
|
#endif
|
|
|
|
|
|
|
|
ret = input_register_device(idev);
|
|
|
|
if (ret < 0) {
|
|
|
|
input_free_device(idev);
|
|
|
|
return -EIO;
|
|
|
|
}
|
|
|
|
|
|
|
|
mce_kbd->idev = idev;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int ir_mce_kbd_unregister(struct rc_dev *dev)
|
|
|
|
{
|
|
|
|
struct mce_kbd_dec *mce_kbd = &dev->raw->mce_kbd;
|
|
|
|
struct input_dev *idev = mce_kbd->idev;
|
|
|
|
|
|
|
|
del_timer_sync(&mce_kbd->rx_timeout);
|
|
|
|
input_unregister_device(idev);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2017-02-12 01:33:38 +03:00
|
|
|
static const struct ir_raw_timings_manchester ir_mce_kbd_timings = {
|
2018-01-05 16:26:51 +03:00
|
|
|
.leader_pulse = MCIR2_PREFIX_PULSE,
|
2017-02-12 01:33:38 +03:00
|
|
|
.invert = 1,
|
|
|
|
.clock = MCIR2_UNIT,
|
|
|
|
.trailer_space = MCIR2_UNIT * 10,
|
|
|
|
};
|
|
|
|
|
|
|
|
/**
|
|
|
|
* ir_mce_kbd_encode() - Encode a scancode as a stream of raw events
|
|
|
|
*
|
|
|
|
* @protocol: protocol to encode
|
|
|
|
* @scancode: scancode to encode
|
|
|
|
* @events: array of raw ir events to write into
|
|
|
|
* @max: maximum size of @events
|
|
|
|
*
|
|
|
|
* Returns: The number of events written.
|
|
|
|
* -ENOBUFS if there isn't enough space in the array to fit the
|
|
|
|
* encoding. In this case all @max events will have been written.
|
|
|
|
*/
|
2017-08-07 23:20:58 +03:00
|
|
|
static int ir_mce_kbd_encode(enum rc_proto protocol, u32 scancode,
|
2017-02-12 01:33:38 +03:00
|
|
|
struct ir_raw_event *events, unsigned int max)
|
|
|
|
{
|
|
|
|
struct ir_raw_event *e = events;
|
|
|
|
int len, ret;
|
|
|
|
u64 raw;
|
|
|
|
|
2017-08-07 23:20:58 +03:00
|
|
|
if (protocol == RC_PROTO_MCIR2_KBD) {
|
2017-02-12 01:33:38 +03:00
|
|
|
raw = scancode |
|
|
|
|
((u64)MCIR2_KEYBOARD_HEADER << MCIR2_KEYBOARD_NBITS);
|
|
|
|
len = MCIR2_KEYBOARD_NBITS + MCIR2_HEADER_NBITS + 1;
|
|
|
|
} else {
|
|
|
|
raw = scancode |
|
|
|
|
((u64)MCIR2_MOUSE_HEADER << MCIR2_MOUSE_NBITS);
|
|
|
|
len = MCIR2_MOUSE_NBITS + MCIR2_HEADER_NBITS + 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
ret = ir_raw_gen_manchester(&e, max, &ir_mce_kbd_timings, len, raw);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return e - events;
|
|
|
|
}
|
|
|
|
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
static struct ir_raw_handler mce_kbd_handler = {
|
2017-08-07 23:20:58 +03:00
|
|
|
.protocols = RC_PROTO_BIT_MCIR2_KBD | RC_PROTO_BIT_MCIR2_MSE,
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
.decode = ir_mce_kbd_decode,
|
2017-02-12 01:33:38 +03:00
|
|
|
.encode = ir_mce_kbd_encode,
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
.raw_register = ir_mce_kbd_register,
|
|
|
|
.raw_unregister = ir_mce_kbd_unregister,
|
2017-02-25 14:51:30 +03:00
|
|
|
.carrier = 36000,
|
[media] rc-core support for Microsoft IR keyboard/mouse
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-07-14 01:09:48 +04:00
|
|
|
};
|
|
|
|
|
|
|
|
static int __init ir_mce_kbd_decode_init(void)
|
|
|
|
{
|
|
|
|
ir_raw_handler_register(&mce_kbd_handler);
|
|
|
|
|
|
|
|
printk(KERN_INFO "IR MCE Keyboard/mouse protocol handler initialized\n");
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void __exit ir_mce_kbd_decode_exit(void)
|
|
|
|
{
|
|
|
|
ir_raw_handler_unregister(&mce_kbd_handler);
|
|
|
|
}
|
|
|
|
|
|
|
|
module_init(ir_mce_kbd_decode_init);
|
|
|
|
module_exit(ir_mce_kbd_decode_exit);
|
|
|
|
|
|
|
|
MODULE_LICENSE("GPL");
|
|
|
|
MODULE_AUTHOR("Jarod Wilson <jarod@redhat.com>");
|
|
|
|
MODULE_DESCRIPTION("MCE Keyboard/mouse IR protocol decoder");
|