WSL2-Linux-Kernel/net/Kconfig

458 строки
13 KiB
Plaintext
Исходник Обычный вид История

# SPDX-License-Identifier: GPL-2.0-only
#
# Network configuration
#
menuconfig NET
bool "Networking support"
select NLATTR
select GENERIC_NET_UTILS
select BPF
help
Unless you really know what you are doing, you should say Y here.
The reason is that some programs need kernel networking support even
when running on a stand-alone machine that isn't connected to any
other computer.
If you are upgrading from an older kernel, you
should consider updating your networking tools too because changes
in the kernel and the tools often go hand in hand. The tools are
contained in the package net-tools, the location and version number
of which are given in <file:Documentation/Changes>.
For a general introduction to Linux networking, it is highly
recommended to read the NET-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
if NET
net/compat/wext: send different messages to compat tasks Wireless extensions have the unfortunate problem that events are multicast netlink messages, and are not independent of pointer size. Thus, currently 32-bit tasks on 64-bit platforms cannot properly receive events and fail with all kinds of strange problems, for instance wpa_supplicant never notices disassociations, due to the way the 64-bit event looks (to a 32-bit process), the fact that the address is all zeroes is lost, it thinks instead it is 00:00:00:00:01:00. The same problem existed with the ioctls, until David Miller fixed those some time ago in an heroic effort. A different problem caused by this is that we cannot send the ASSOCREQIE/ASSOCRESPIE events because sending them causes a 32-bit wpa_supplicant on a 64-bit system to overwrite its internal information, which is worse than it not getting the information at all -- so we currently resort to sending a custom string event that it then parses. This, however, has a severe size limitation we are frequently hitting with modern access points; this limitation would can be lifted after this patch by sending the correct binary, not custom, event. A similar problem apparently happens for some other netlink users on x86_64 with 32-bit tasks due to the alignment for 64-bit quantities. In order to fix these problems, I have implemented a way to send compat messages to tasks. When sending an event, we send the non-compat event data together with a compat event data in skb_shinfo(main_skb)->frag_list. Then, when the event is read from the socket, the netlink code makes sure to pass out only the skb that is compatible with the task. This approach was suggested by David Miller, my original approach required always sending two skbs but that had various small problems. To determine whether compat is needed or not, I have used the MSG_CMSG_COMPAT flag, and adjusted the call path for recv and recvfrom to include it, even if those calls do not have a cmsg parameter. I have not solved one small part of the problem, and I don't think it is necessary to: if a 32-bit application uses read() rather than any form of recvmsg() it will still get the wrong (64-bit) event. However, neither do applications actually do this, nor would it be a regression. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-01 15:26:02 +04:00
config WANT_COMPAT_NETLINK_MESSAGES
bool
help
This option can be selected by other options that need compat
netlink messages.
config COMPAT_NETLINK_MESSAGES
def_bool y
depends on COMPAT
depends on WEXT_CORE || WANT_COMPAT_NETLINK_MESSAGES
net/compat/wext: send different messages to compat tasks Wireless extensions have the unfortunate problem that events are multicast netlink messages, and are not independent of pointer size. Thus, currently 32-bit tasks on 64-bit platforms cannot properly receive events and fail with all kinds of strange problems, for instance wpa_supplicant never notices disassociations, due to the way the 64-bit event looks (to a 32-bit process), the fact that the address is all zeroes is lost, it thinks instead it is 00:00:00:00:01:00. The same problem existed with the ioctls, until David Miller fixed those some time ago in an heroic effort. A different problem caused by this is that we cannot send the ASSOCREQIE/ASSOCRESPIE events because sending them causes a 32-bit wpa_supplicant on a 64-bit system to overwrite its internal information, which is worse than it not getting the information at all -- so we currently resort to sending a custom string event that it then parses. This, however, has a severe size limitation we are frequently hitting with modern access points; this limitation would can be lifted after this patch by sending the correct binary, not custom, event. A similar problem apparently happens for some other netlink users on x86_64 with 32-bit tasks due to the alignment for 64-bit quantities. In order to fix these problems, I have implemented a way to send compat messages to tasks. When sending an event, we send the non-compat event data together with a compat event data in skb_shinfo(main_skb)->frag_list. Then, when the event is read from the socket, the netlink code makes sure to pass out only the skb that is compatible with the task. This approach was suggested by David Miller, my original approach required always sending two skbs but that had various small problems. To determine whether compat is needed or not, I have used the MSG_CMSG_COMPAT flag, and adjusted the call path for recv and recvfrom to include it, even if those calls do not have a cmsg parameter. I have not solved one small part of the problem, and I don't think it is necessary to: if a 32-bit application uses read() rather than any form of recvmsg() it will still get the wrong (64-bit) event. However, neither do applications actually do this, nor would it be a regression. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-01 15:26:02 +04:00
help
This option makes it possible to send different netlink messages
to tasks depending on whether the task is a compat task or not. To
achieve this, you need to set skb_shinfo(skb)->frag_list to the
compat skb before sending the skb, the netlink code will sort out
which message to actually pass to the task.
Newly written code should NEVER need this option but do
compat-independent messages instead!
config NET_INGRESS
bool
net, sched: add clsact qdisc This work adds a generalization of the ingress qdisc as a qdisc holding only classifiers. The clsact qdisc works on ingress, but also on egress. In both cases, it's execution happens without taking the qdisc lock, and the main difference for the egress part compared to prior version of [1] is that this can be applied with _any_ underlying real egress qdisc (also classless ones). Besides solving the use-case of [1], that is, allowing for more programmability on assigning skb->priority for the mqprio case that is supported by most popular 10G+ NICs, it also opens up a lot more flexibility for other tc applications. The main work on classification can already be done at clsact egress time if the use-case allows and state stored for later retrieval f.e. again in skb->priority with major/minors (which is checked by most classful qdiscs before consulting tc_classify()) and/or in other skb fields like skb->tc_index for some light-weight post-processing to get to the eventual classid in case of a classful qdisc. Another use case is that the clsact egress part allows to have a central egress counterpart to the ingress classifiers, so that classifiers can easily share state (e.g. in cls_bpf via eBPF maps) for ingress and egress. Currently, default setups like mq + pfifo_fast would require for this to use, for example, prio qdisc instead (to get a tc_classify() run) and to duplicate the egress classifier for each queue. With clsact, it allows for leaving the setup as is, it can additionally assign skb->priority to put the skb in one of pfifo_fast's bands and it can share state with maps. Moreover, we can access the skb's dst entry (f.e. to retrieve tclassid) w/o the need to perform a skb_dst_force() to hold on to it any longer. In lwt case, we can also use this facility to setup dst metadata via cls_bpf (bpf_skb_set_tunnel_key()) without needing a real egress qdisc just for that (case of IFF_NO_QUEUE devices, for example). The realization can be done without any changes to the scheduler core framework. All it takes is that we have two a-priori defined minors/child classes, where we can mux between ingress and egress classifier list (dev->ingress_cl_list and dev->egress_cl_list, latter stored close to dev->_tx to avoid extra cacheline miss for moderate loads). The egress part is a bit similar modelled to handle_ing() and patched to a noop in case the functionality is not used. Both handlers are now called sch_handle_ingress() and sch_handle_egress(), code sharing among the two doesn't seem practical as there are various minor differences in both paths, so that making them conditional in a single handler would rather slow things down. Full compatibility to ingress qdisc is provided as well. Since both piggyback on TC_H_CLSACT, only one of them (ingress/clsact) can exist per netdevice, and thus ingress qdisc specific behaviour can be retained for user space. This means, either a user does 'tc qdisc add dev foo ingress' and configures ingress qdisc as usual, or the 'tc qdisc add dev foo clsact' alternative, where both, ingress and egress classifier can be configured as in the below example. ingress qdisc supports attaching classifier to any minor number whereas clsact has two fixed minors for muxing between the lists, therefore to not break user space setups, they are better done as two separate qdiscs. I decided to extend the sch_ingress module with clsact functionality so that commonly used code can be reused, the module is being aliased with sch_clsact so that it can be auto-loaded properly. Alternative would have been to add a flag when initializing ingress to alter its behaviour plus aliasing to a different name (as it's more than just ingress). However, the first would end up, based on the flag, choosing the new/old behaviour by calling different function implementations to handle each anyway, the latter would require to register ingress qdisc once again under different alias. So, this really begs to provide a minimal, cleaner approach to have Qdisc_ops and Qdisc_class_ops by its own that share callbacks used by both. Example, adding qdisc: # tc qdisc add dev foo clsact # tc qdisc show dev foo qdisc mq 0: root qdisc pfifo_fast 0: parent :1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :4 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc clsact ffff: parent ffff:fff1 Adding filters (deleting, etc works analogous by specifying ingress/egress): # tc filter add dev foo ingress bpf da obj bar.o sec ingress # tc filter add dev foo egress bpf da obj bar.o sec egress # tc filter show dev foo ingress filter protocol all pref 49152 bpf filter protocol all pref 49152 bpf handle 0x1 bar.o:[ingress] direct-action # tc filter show dev foo egress filter protocol all pref 49152 bpf filter protocol all pref 49152 bpf handle 0x1 bar.o:[egress] direct-action A 'tc filter show dev foo' or 'tc filter show dev foo parent ffff:' will show an empty list for clsact. Either using the parent names (ingress/egress) or specifying the full major/minor will then show the related filter lists. Prior work on a mqprio prequeue() facility [1] was done mainly by John Fastabend. [1] http://patchwork.ozlabs.org/patch/512949/ Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-08 00:29:47 +03:00
config NET_EGRESS
bool
config NET_REDIRECT
bool
sk_buff: add skb extension infrastructure This adds an optional extension infrastructure, with ispec (xfrm) and bridge netfilter as first users. objdiff shows no changes if kernel is built without xfrm and br_netfilter support. The third (planned future) user is Multipath TCP which is still out-of-tree. MPTCP needs to map logical mptcp sequence numbers to the tcp sequence numbers used by individual subflows. This DSS mapping is read/written from tcp option space on receive and written to tcp option space on transmitted tcp packets that are part of and MPTCP connection. Extending skb_shared_info or adding a private data field to skb fclones doesn't work for incoming skb, so a different DSS propagation method would be required for the receive side. mptcp has same requirements as secpath/bridge netfilter: 1. extension memory is released when the sk_buff is free'd. 2. data is shared after cloning an skb (clone inherits extension) 3. adding extension to an skb will COW the extension buffer if needed. The "MPTCP upstreaming" effort adds SKB_EXT_MPTCP extension to store the mapping for tx and rx processing. Two new members are added to sk_buff: 1. 'active_extensions' byte (filling a hole), telling which extensions are available for this skb. This has two purposes. a) avoids the need to initialize the pointer. b) allows to "delete" an extension by clearing its bit value in ->active_extensions. While it would be possible to store the active_extensions byte in the extension struct instead of sk_buff, there is one problem with this: When an extension has to be disabled, we can always clear the bit in skb->active_extensions. But in case it would be stored in the extension buffer itself, we might have to COW it first, if we are dealing with a cloned skb. On kmalloc failure we would be unable to turn an extension off. 2. extension pointer, located at the end of the sk_buff. If the active_extensions byte is 0, the pointer is undefined, it is not initialized on skb allocation. This adds extra code to skb clone and free paths (to deal with refcount/free of extension area) but this replaces similar code that manages skb->nf_bridge and skb->sp structs in the followup patches of the series. It is possible to add support for extensions that are not preseved on clones/copies. To do this, it would be needed to define a bitmask of all extensions that need copy/cow semantics, and change __skb_ext_copy() to check ->active_extensions & SKB_EXT_PRESERVE_ON_CLONE, then just set ->active_extensions to 0 on the new clone. This isn't done here because all extensions that get added here need the copy/cow semantics. v2: Allocate entire extension space using kmem_cache. Upside is that this allows better tracking of used memory, downside is that we will allocate more space than strictly needed in most cases (its unlikely that all extensions are active/needed at same time for same skb). The allocated memory (except the small extension header) is not cleared, so no additonal overhead aside from memory usage. Avoid atomic_dec_and_test operation on skb_ext_put() by using similar trick as kfree_skbmem() does with fclone_ref: If recount is 1, there is no concurrent user and we can free right away. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18 19:15:16 +03:00
config SKB_EXTENSIONS
bool
menu "Networking options"
source "net/packet/Kconfig"
source "net/unix/Kconfig"
source "net/tls/Kconfig"
source "net/xfrm/Kconfig"
source "net/iucv/Kconfig"
source "net/smc/Kconfig"
source "net/xdp/Kconfig"
config INET
bool "TCP/IP networking"
help
These are the protocols used on the Internet and on most local
Ethernets. It is highly recommended to say Y here (this will enlarge
your kernel by about 400 KB), since some programs (e.g. the X window
system) use TCP/IP even if your machine is not connected to any
other computer. You will get the so-called loopback device which
allows you to ping yourself (great fun, that!).
For an excellent introduction to Linux networking, please read the
Linux Networking HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
If you say Y here and also to "/proc file system support" and
"Sysctl support" below, you can change various aspects of the
behavior of the TCP/IP code by writing to the (virtual) files in
/proc/sys/net/ipv4/*; the options are explained in the file
<file:Documentation/networking/ip-sysctl.rst>.
Short answer: say Y.
if INET
source "net/ipv4/Kconfig"
source "net/ipv6/Kconfig"
source "net/netlabel/Kconfig"
source "net/mptcp/Kconfig"
endif # if INET
config NETWORK_SECMARK
bool "Security Marking"
help
This enables security marking of network packets, similar
to nfmark, but designated for security purposes.
If you are unsure how to answer this question, answer N.
net: ptp: move PTP classifier in its own file This commit fixes a build error reported by Fengguang, that is triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set: ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined! The fix is to introduce its own file for the PTP BPF classifier, so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select it independently from each other. IXP4xx driver on ARM needs to select it as well since it does not seem to select PTP_1588_CLOCK or similar that would pull it in automatically. This also allows for hiding all of the internals of the BPF PTP program inside that file, and only exporting relevant API bits to drivers. This patch also adds a kdoc documentation of ptp_classify_raw() API to make it clear that it can return PTP_CLASS_* defines. Also, the BPF program has been translated into bpf_asm code, so that it can be more easily read and altered (extensively documented in [1]). In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg tools, so the commented program can simply be translated via `./bpf_asm -c prog` where prog is a file that contains the commented code. This makes it easily readable/verifiable and when there's a need to change something, jump offsets etc do not need to be replaced manually which can be very error prone. Instead, a newly translated version via bpf_asm can simply replace the old code. I have checked opcode diffs before/after and it's the very same filter. [1] Documentation/networking/filter.txt Fixes: 164d8c666521 ("net: ptp: do not reimplement PTP/BPF classifier") Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Jiri Benc <jbenc@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-01 18:20:23 +04:00
config NET_PTP_CLASSIFY
def_bool n
config NETWORK_PHY_TIMESTAMPING
bool "Timestamping in PHY devices"
net: ptp: move PTP classifier in its own file This commit fixes a build error reported by Fengguang, that is triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set: ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined! The fix is to introduce its own file for the PTP BPF classifier, so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select it independently from each other. IXP4xx driver on ARM needs to select it as well since it does not seem to select PTP_1588_CLOCK or similar that would pull it in automatically. This also allows for hiding all of the internals of the BPF PTP program inside that file, and only exporting relevant API bits to drivers. This patch also adds a kdoc documentation of ptp_classify_raw() API to make it clear that it can return PTP_CLASS_* defines. Also, the BPF program has been translated into bpf_asm code, so that it can be more easily read and altered (extensively documented in [1]). In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg tools, so the commented program can simply be translated via `./bpf_asm -c prog` where prog is a file that contains the commented code. This makes it easily readable/verifiable and when there's a need to change something, jump offsets etc do not need to be replaced manually which can be very error prone. Instead, a newly translated version via bpf_asm can simply replace the old code. I have checked opcode diffs before/after and it's the very same filter. [1] Documentation/networking/filter.txt Fixes: 164d8c666521 ("net: ptp: do not reimplement PTP/BPF classifier") Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Jiri Benc <jbenc@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-01 18:20:23 +04:00
select NET_PTP_CLASSIFY
help
This allows timestamping of network packets by PHYs (or
other MII bus snooping devices) with hardware timestamping
capabilities. This option adds some overhead in the transmit
and receive paths.
If you are unsure how to answer this question, answer N.
menuconfig NETFILTER
bool "Network packet filtering framework (Netfilter)"
help
Netfilter is a framework for filtering and mangling network packets
that pass through your Linux box.
The most common use of packet filtering is to run your Linux box as
a firewall protecting a local network from the Internet. The type of
firewall provided by this kernel support is called a "packet
filter", which means that it can reject individual network packets
based on type, source, destination etc. The other kind of firewall,
a "proxy-based" one, is more secure but more intrusive and more
bothersome to set up; it inspects the network traffic much more
closely, modifies it and has knowledge about the higher level
protocols, which a packet filter lacks. Moreover, proxy-based
firewalls often require changes to the programs running on the local
clients. Proxy-based firewalls don't need support by the kernel, but
they are often combined with a packet filter, which only works if
you say Y here.
You should also say Y here if you intend to use your Linux box as
the gateway to the Internet for a local network of machines without
globally valid IP addresses. This is called "masquerading": if one
of the computers on your local network wants to send something to
the outside, your box can "masquerade" as that computer, i.e. it
forwards the traffic to the intended outside destination, but
modifies the packets to make it look like they came from the
firewall box itself. It works both ways: if the outside host
replies, the Linux box will silently forward the traffic to the
correct local computer. This way, the computers on your local net
are completely invisible to the outside world, even though they can
reach the outside and can receive replies. It is even possible to
run globally visible servers from within a masqueraded local network
using a mechanism called portforwarding. Masquerading is also often
called NAT (Network Address Translation).
Another use of Netfilter is in transparent proxying: if a machine on
the local network tries to connect to an outside host, your Linux
box can transparently forward the traffic to a local server,
typically a caching proxy server.
Yet another use of Netfilter is building a bridging firewall. Using
a bridge with Network packet filtering enabled makes iptables "see"
the bridged traffic. For filtering on the lower network and Ethernet
protocols over the bridge, use ebtables (under bridge netfilter
configuration).
Various modules exist for netfilter which replace the previous
masquerading (ipmasqadm), packet filtering (ipchains), transparent
proxying, and portforwarding mechanisms. Please see
<file:Documentation/Changes> under "iptables" for the location of
these packages.
if NETFILTER
config NETFILTER_ADVANCED
bool "Advanced netfilter configuration"
depends on NETFILTER
default y
help
If you say Y here you can select between all the netfilter modules.
If you say N the more unusual ones will not be shown and the
basic ones needed by most people will default to 'M'.
If unsure, say Y.
config BRIDGE_NETFILTER
tristate "Bridged IP/ARP packets filtering"
depends on BRIDGE
depends on NETFILTER && INET
depends on NETFILTER_ADVANCED
select NETFILTER_FAMILY_BRIDGE
select SKB_EXTENSIONS
help
Enabling this option will let arptables resp. iptables see bridged
ARP resp. IP traffic. If you want a bridging firewall, you probably
want this option enabled.
Enabling or disabling this option doesn't enable or disable
ebtables.
If unsure, say N.
source "net/netfilter/Kconfig"
source "net/ipv4/netfilter/Kconfig"
source "net/ipv6/netfilter/Kconfig"
source "net/decnet/netfilter/Kconfig"
source "net/bridge/netfilter/Kconfig"
endif
net: add skeleton of bpfilter kernel module bpfilter.ko consists of bpfilter_kern.c (normal kernel module code) and user mode helper code that is embedded into bpfilter.ko The steps to build bpfilter.ko are the following: - main.c is compiled by HOSTCC into the bpfilter_umh elf executable file - with quite a bit of objcopy and Makefile magic the bpfilter_umh elf file is converted into bpfilter_umh.o object file with _binary_net_bpfilter_bpfilter_umh_start and _end symbols Example: $ nm ./bld_x64/net/bpfilter/bpfilter_umh.o 0000000000004cf8 T _binary_net_bpfilter_bpfilter_umh_end 0000000000004cf8 A _binary_net_bpfilter_bpfilter_umh_size 0000000000000000 T _binary_net_bpfilter_bpfilter_umh_start - bpfilter_umh.o and bpfilter_kern.o are linked together into bpfilter.ko bpfilter_kern.c is a normal kernel module code that calls the fork_usermode_blob() helper to execute part of its own data as a user mode process. Notice that _binary_net_bpfilter_bpfilter_umh_start - end is placed into .init.rodata section, so it's freed as soon as __init function of bpfilter.ko is finished. As part of __init the bpfilter.ko does first request/reply action via two unix pipe provided by fork_usermode_blob() helper to make sure that umh is healthy. If not it will kill it via pid. Later bpfilter_process_sockopt() will be called from bpfilter hooks in get/setsockopt() to pass iptable commands into umh via bpfilter.ko If admin does 'rmmod bpfilter' the __exit code bpfilter.ko will kill umh as well. Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-22 05:22:30 +03:00
source "net/bpfilter/Kconfig"
source "net/dccp/Kconfig"
source "net/sctp/Kconfig"
source "net/rds/Kconfig"
source "net/tipc/Kconfig"
source "net/atm/Kconfig"
source "net/l2tp/Kconfig"
source "net/802/Kconfig"
source "net/bridge/Kconfig"
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 17:44:02 +04:00
source "net/dsa/Kconfig"
source "net/8021q/Kconfig"
source "net/decnet/Kconfig"
source "net/llc/Kconfig"
source "drivers/net/appletalk/Kconfig"
source "net/x25/Kconfig"
source "net/lapb/Kconfig"
source "net/phonet/Kconfig"
source "net/6lowpan/Kconfig"
source "net/ieee802154/Kconfig"
source "net/mac802154/Kconfig"
source "net/sched/Kconfig"
source "net/dcb/Kconfig"
DNS: Separate out CIFS DNS Resolver code Separate out the DNS resolver key type from the CIFS filesystem into its own module so that it can be made available for general use, including the AFS filesystem module. This facility makes it possible for the kernel to upcall to userspace to have it issue DNS requests, package up the replies and present them to the kernel in a useful form. The kernel is then able to cache the DNS replies as keys can be retained in keyrings. Resolver keys are of type "dns_resolver" and have a case-insensitive description that is of the form "[<type>:]<domain_name>". The optional <type> indicates the particular DNS lookup and packaging that's required. The <domain_name> is the query to be made. If <type> isn't given, a basic hostname to IP address lookup is made, and the result is stored in the key in the form of a printable string consisting of a comma-separated list of IPv4 and IPv6 addresses. This key type is supported by userspace helpers driven from /sbin/request-key and configured through /etc/request-key.conf. The cifs.upcall utility is invoked for UNC path server name to IP address resolution. The CIFS functionality is encapsulated by the dns_resolve_unc_to_ip() function, which is used to resolve a UNC path to an IP address for CIFS filesystem. This part remains in the CIFS module for now. See the added Documentation/networking/dns_resolver.txt for more information. Signed-off-by: Wang Lei <wang840925@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2010-08-04 18:16:33 +04:00
source "net/dns_resolver/Kconfig"
source "net/batman-adv/Kconfig"
source "net/openvswitch/Kconfig"
VSOCK: Introduce VM Sockets VM Sockets allows communication between virtual machines and the hypervisor. User level applications both in a virtual machine and on the host can use the VM Sockets API, which facilitates fast and efficient communication between guest virtual machines and their host. A socket address family, designed to be compatible with UDP and TCP at the interface level, is provided. Today, VM Sockets is used by various VMware Tools components inside the guest for zero-config, network-less access to VMware host services. In addition to this, VMware's users are using VM Sockets for various applications, where network access of the virtual machine is restricted or non-existent. Examples of this are VMs communicating with device proxies for proprietary hardware running as host applications and automated testing of applications running within virtual machines. The VMware VM Sockets are similar to other socket types, like Berkeley UNIX socket interface. The VM Sockets module supports both connection-oriented stream sockets like TCP, and connectionless datagram sockets like UDP. The VM Sockets protocol family is defined as "AF_VSOCK" and the socket operations split for SOCK_DGRAM and SOCK_STREAM. For additional information about the use of VM Sockets, please refer to the VM Sockets Programming Guide available at: https://www.vmware.com/support/developer/vmci-sdk/ Signed-off-by: George Zhang <georgezhang@vmware.com> Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Andy king <acking@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-06 18:23:56 +04:00
source "net/vmw_vsock/Kconfig"
source "net/netlink/Kconfig"
MPLS: Add limited GSO support In the case where a non-MPLS packet is received and an MPLS stack is added it may well be the case that the original skb is GSO but the NIC used for transmit does not support GSO of MPLS packets. The aim of this code is to provide GSO in software for MPLS packets whose skbs are GSO. SKB Usage: When an implementation adds an MPLS stack to a non-MPLS packet it should do the following to skb metadata: * Set skb->inner_protocol to the old non-MPLS ethertype of the packet. skb->inner_protocol is added by this patch. * Set skb->protocol to the new MPLS ethertype of the packet. * Set skb->network_header to correspond to the end of the L3 header, including the MPLS label stack. I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to kernel" which adds MPLS support to the kernel datapath of Open vSwtich. That patch sets the above requirements in datapath/actions.c:push_mpls() and was used to exercise this code. The datapath patch is against the Open vSwtich tree but it is intended that it be added to the Open vSwtich code present in the mainline Linux kernel at some point. Features: I believe that the approach that I have taken is at least partially consistent with the handling of other protocols. Jesse, I understand that you have some ideas here. I am more than happy to change my implementation. This patch adds dev->mpls_features which may be used by devices to advertise features supported for MPLS packets. A new NETIF_F_MPLS_GSO feature is added for devices which support hardware MPLS GSO offload. Currently no devices support this and MPLS GSO always falls back to software. Alternate Implementation: One possible alternate implementation is to teach netif_skb_features() and skb_network_protocol() about MPLS, in a similar way to their understanding of VLANs. I believe this would avoid the need for net/mpls/mpls_gso.c and in particular the calls to __skb_push() and __skb_push() in mpls_gso_segment(). I have decided on the implementation in this patch as it should not introduce any overhead in the case where mpls_gso is not compiled into the kernel or inserted as a module. MPLS GSO suggested by Jesse Gross. Based in part on "v4 GRE: Add TCP segmentation offload for GRE" by Pravin B Shelar. Cc: Jesse Gross <jesse@nicira.com> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-24 01:02:52 +04:00
source "net/mpls/Kconfig"
source "net/nsh/Kconfig"
source "net/hsr/Kconfig"
source "net/switchdev/Kconfig"
source "net/l3mdev/Kconfig"
source "net/qrtr/Kconfig"
source "net/ncsi/Kconfig"
config PCPU_DEV_REFCNT
bool "Use percpu variables to maintain network device refcount"
depends on SMP
default y
help
network device refcount are using per cpu variables if this option is set.
This can be forced to N to detect underflows (with a performance drop).
config RPS
bool
depends on SMP && SYSFS
default y
config RFS_ACCEL
bool
depends on RPS
select CPU_RMAP
default y
config SOCK_RX_QUEUE_MAPPING
bool
config XPS
bool
depends on SMP
select SOCK_RX_QUEUE_MAPPING
default y
config HWBM
bool
config CGROUP_NET_PRIO
bool "Network priority cgroup"
depends on CGROUPS
select SOCK_CGROUP_DATA
help
Cgroup subsystem for use in assigning processes to network priorities on
a per-interface basis.
config CGROUP_NET_CLASSID
bool "Network classid cgroup"
depends on CGROUPS
select SOCK_CGROUP_DATA
help
Cgroup subsystem for use as general purpose socket classid marker that is
being used in cls_cgroup and for netfilter matching.
config NET_RX_BUSY_POLL
bool
default y
config BQL
bool
depends on SYSFS
select DQL
default y
config BPF_STREAM_PARSER
bool "enable BPF STREAM_PARSER"
bpf, sockmap: convert to generic sk_msg interface Add a generic sk_msg layer, and convert current sockmap and later kTLS over to make use of it. While sk_buff handles network packet representation from netdevice up to socket, sk_msg handles data representation from application to socket layer. This means that sk_msg framework spans across ULP users in the kernel, and enables features such as introspection or filtering of data with the help of BPF programs that operate on this data structure. Latter becomes in particular useful for kTLS where data encryption is deferred into the kernel, and as such enabling the kernel to perform L7 introspection and policy based on BPF for TLS connections where the record is being encrypted after BPF has run and came to a verdict. In order to get there, first step is to transform open coding of scatter-gather list handling into a common core framework that subsystems can use. The code itself has been split and refactored into three bigger pieces: i) the generic sk_msg API which deals with managing the scatter gather ring, providing helpers for walking and mangling, transferring application data from user space into it, and preparing it for BPF pre/post-processing, ii) the plain sock map itself where sockets can be attached to or detached from; these bits are independent of i) which can now be used also without sock map, and iii) the integration with plain TCP as one protocol to be used for processing L7 application data (later this could e.g. also be extended to other protocols like UDP). The semantics are the same with the old sock map code and therefore no change of user facing behavior or APIs. While pursuing this work it also helped finding a number of bugs in the old sockmap code that we've fixed already in earlier commits. The test_sockmap kselftest suite passes through fine as well. Joint work with John. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-13 03:45:58 +03:00
depends on INET
depends on BPF_SYSCALL
bpf, sockmap: convert to generic sk_msg interface Add a generic sk_msg layer, and convert current sockmap and later kTLS over to make use of it. While sk_buff handles network packet representation from netdevice up to socket, sk_msg handles data representation from application to socket layer. This means that sk_msg framework spans across ULP users in the kernel, and enables features such as introspection or filtering of data with the help of BPF programs that operate on this data structure. Latter becomes in particular useful for kTLS where data encryption is deferred into the kernel, and as such enabling the kernel to perform L7 introspection and policy based on BPF for TLS connections where the record is being encrypted after BPF has run and came to a verdict. In order to get there, first step is to transform open coding of scatter-gather list handling into a common core framework that subsystems can use. The code itself has been split and refactored into three bigger pieces: i) the generic sk_msg API which deals with managing the scatter gather ring, providing helpers for walking and mangling, transferring application data from user space into it, and preparing it for BPF pre/post-processing, ii) the plain sock map itself where sockets can be attached to or detached from; these bits are independent of i) which can now be used also without sock map, and iii) the integration with plain TCP as one protocol to be used for processing L7 application data (later this could e.g. also be extended to other protocols like UDP). The semantics are the same with the old sock map code and therefore no change of user facing behavior or APIs. While pursuing this work it also helped finding a number of bugs in the old sockmap code that we've fixed already in earlier commits. The test_sockmap kselftest suite passes through fine as well. Joint work with John. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-13 03:45:58 +03:00
depends on CGROUP_BPF
select STREAM_PARSER
bpf, sockmap: convert to generic sk_msg interface Add a generic sk_msg layer, and convert current sockmap and later kTLS over to make use of it. While sk_buff handles network packet representation from netdevice up to socket, sk_msg handles data representation from application to socket layer. This means that sk_msg framework spans across ULP users in the kernel, and enables features such as introspection or filtering of data with the help of BPF programs that operate on this data structure. Latter becomes in particular useful for kTLS where data encryption is deferred into the kernel, and as such enabling the kernel to perform L7 introspection and policy based on BPF for TLS connections where the record is being encrypted after BPF has run and came to a verdict. In order to get there, first step is to transform open coding of scatter-gather list handling into a common core framework that subsystems can use. The code itself has been split and refactored into three bigger pieces: i) the generic sk_msg API which deals with managing the scatter gather ring, providing helpers for walking and mangling, transferring application data from user space into it, and preparing it for BPF pre/post-processing, ii) the plain sock map itself where sockets can be attached to or detached from; these bits are independent of i) which can now be used also without sock map, and iii) the integration with plain TCP as one protocol to be used for processing L7 application data (later this could e.g. also be extended to other protocols like UDP). The semantics are the same with the old sock map code and therefore no change of user facing behavior or APIs. While pursuing this work it also helped finding a number of bugs in the old sockmap code that we've fixed already in earlier commits. The test_sockmap kselftest suite passes through fine as well. Joint work with John. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-13 03:45:58 +03:00
select NET_SOCK_MSG
help
Enabling this allows a TCP stream parser to be used with
BPF_MAP_TYPE_SOCKMAP.
config NET_FLOW_LIMIT
bool
depends on RPS
default y
help
The network stack has to drop packets when a receive processing CPU's
backlog reaches netdev_max_backlog. If a few out of many active flows
generate the vast majority of load, drop their traffic earlier to
maintain capacity for the other flows. This feature provides servers
with many clients some protection against DoS by a single (spoofed)
flow that greatly exceeds average workload.
menu "Network testing"
config NET_PKTGEN
tristate "Packet Generator (USE WITH CAUTION)"
depends on INET && PROC_FS
help
This module will inject preconfigured packets, at a configurable
rate, out of a given interface. It is used for network interface
stress testing and performance analysis. If you don't understand
what was just said, you don't need it: say N.
Documentation on how to use the packet generator can be found
at <file:Documentation/networking/pktgen.rst>.
To compile this code as a module, choose M here: the
module will be called pktgen.
config NET_DROP_MONITOR
tristate "Network packet drop alerting service"
depends on INET && TRACEPOINTS
help
This feature provides an alerting service to userspace in the
event that packets are discarded in the network stack. Alerts
are broadcast via netlink socket to any listening user space
process. If you don't need network drop alerts, or if you are ok
just checking the various proc files and other utilities for
drop statistics, say N here.
endmenu
endmenu
source "net/ax25/Kconfig"
source "net/can/Kconfig"
source "net/bluetooth/Kconfig"
source "net/rxrpc/Kconfig"
source "net/kcm/Kconfig"
strparser: Stream parser for messages This patch introduces a utility for parsing application layer protocol messages in a TCP stream. This is a generalization of the mechanism implemented of Kernel Connection Multiplexor. The API includes a context structure, a set of callbacks, utility functions, and a data ready function. A stream parser instance is defined by a strparse structure that is bound to a TCP socket. The function to initialize the structure is: int strp_init(struct strparser *strp, struct sock *csk, struct strp_callbacks *cb); csk is the TCP socket being bound to and cb are the parser callbacks. The upper layer calls strp_tcp_data_ready when data is ready on the lower socket for strparser to process. This should be called from a data_ready callback that is set on the socket: void strp_tcp_data_ready(struct strparser *strp); A parser is bound to a TCP socket by setting data_ready function to strp_tcp_data_ready so that all receive indications on the socket go through the parser. This is assumes that sk_user_data is set to the strparser structure. There are four callbacks. - parse_msg is called to parse the message (returns length or error). - rcv_msg is called when a complete message has been received - read_sock_done is called when data_ready function exits - abort_parser is called to abort the parser The input to parse_msg is an skbuff which contains next message under construction. The backend processing of parse_msg will parse the application layer protocol headers to determine the length of the message in the stream. The possible return values are: >0 : indicates length of successfully parsed message 0 : indicates more data must be received to parse the message -ESTRPIPE : current message should not be processed by the kernel, return control of the socket to userspace which can proceed to read the messages itself other < 0 : Error is parsing, give control back to userspace assuming that synchronzation is lost and the stream is unrecoverable (application expected to close TCP socket) In the case of error return (< 0) strparse will stop the parser and report and error to userspace. The application must deal with the error. To handle the error the strparser is unbound from the TCP socket. If the error indicates that the stream TCP socket is at recoverable point (ESTRPIPE) then the application can read the TCP socket to process the stream. Once the application has dealt with the exceptions in the stream, it may again bind the socket to a strparser to continue data operations. Note that ENODATA may be returned to the application. In this case parse_msg returned -ESTRPIPE, however strparser was unable to maintain synchronization of the stream (i.e. some of the message in question was already read by the parser). strp_pause and strp_unpause are used to provide flow control. For instance, if rcv_msg is called but the upper layer can't immediately consume the message it can hold the message and pause strparser. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-16 00:51:01 +03:00
source "net/strparser/Kconfig"
config FIB_RULES
bool
menuconfig WIRELESS
bool "Wireless"
depends on !S390
default y
if WIRELESS
source "net/wireless/Kconfig"
source "net/mac80211/Kconfig"
endif # WIRELESS
source "net/rfkill/Kconfig"
source "net/9p/Kconfig"
source "net/caif/Kconfig"
source "net/ceph/Kconfig"
source "net/nfc/Kconfig"
net: Introduce psample, a new genetlink channel for packet sampling Add a general way for kernel modules to sample packets, without being tied to any specific subsystem. This netlink channel can be used by tc, iptables, etc. and allow to standardize packet sampling in the kernel. For every sampled packet, the psample module adds the following metadata fields: PSAMPLE_ATTR_IIFINDEX - the packets input ifindex, if applicable PSAMPLE_ATTR_OIFINDEX - the packet output ifindex, if applicable PSAMPLE_ATTR_ORIGSIZE - the packet's original size, in case it has been truncated during sampling PSAMPLE_ATTR_SAMPLE_GROUP - the packet's sample group, which is set by the user who initiated the sampling. This field allows the user to differentiate between several samplers working simultaneously and filter packets relevant to him PSAMPLE_ATTR_GROUP_SEQ - sequence counter of last sent packet. The sequence is kept for each group PSAMPLE_ATTR_SAMPLE_RATE - the sampling rate used for sampling the packets PSAMPLE_ATTR_DATA - the actual packet bits The sampled packets are sent to the PSAMPLE_NL_MCGRP_SAMPLE multicast group. In addition, add the GET_GROUPS netlink command which allows the user to see the current sample groups, their refcount and sequence number. This command currently supports only netlink dump mode. Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-23 13:07:08 +03:00
source "net/psample/Kconfig"
source "net/ife/Kconfig"
config LWTUNNEL
bool "Network light weight tunnels"
help
This feature provides an infrastructure to support light weight
tunnels like mpls. There is no netdevice associated with a light
weight tunnel endpoint. Tunnel encapsulation parameters are stored
with light weight tunnel state associated with fib routes.
config LWTUNNEL_BPF
bool "Execute BPF program as route nexthop action"
depends on LWTUNNEL && INET
default y if LWTUNNEL=y
help
Allows to run BPF programs as a nexthop action following a route
lookup for incoming and outgoing packets.
config DST_CACHE
bool
default n
config GRO_CELLS
bool
default n
config SOCK_VALIDATE_XMIT
bool
config NET_SELFTESTS
def_tristate PHYLIB
depends on PHYLIB && INET
bpf, sockmap: convert to generic sk_msg interface Add a generic sk_msg layer, and convert current sockmap and later kTLS over to make use of it. While sk_buff handles network packet representation from netdevice up to socket, sk_msg handles data representation from application to socket layer. This means that sk_msg framework spans across ULP users in the kernel, and enables features such as introspection or filtering of data with the help of BPF programs that operate on this data structure. Latter becomes in particular useful for kTLS where data encryption is deferred into the kernel, and as such enabling the kernel to perform L7 introspection and policy based on BPF for TLS connections where the record is being encrypted after BPF has run and came to a verdict. In order to get there, first step is to transform open coding of scatter-gather list handling into a common core framework that subsystems can use. The code itself has been split and refactored into three bigger pieces: i) the generic sk_msg API which deals with managing the scatter gather ring, providing helpers for walking and mangling, transferring application data from user space into it, and preparing it for BPF pre/post-processing, ii) the plain sock map itself where sockets can be attached to or detached from; these bits are independent of i) which can now be used also without sock map, and iii) the integration with plain TCP as one protocol to be used for processing L7 application data (later this could e.g. also be extended to other protocols like UDP). The semantics are the same with the old sock map code and therefore no change of user facing behavior or APIs. While pursuing this work it also helped finding a number of bugs in the old sockmap code that we've fixed already in earlier commits. The test_sockmap kselftest suite passes through fine as well. Joint work with John. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-10-13 03:45:58 +03:00
config NET_SOCK_MSG
bool
default n
help
The NET_SOCK_MSG provides a framework for plain sockets (e.g. TCP) or
ULPs (upper layer modules, e.g. TLS) to process L7 application data
with the help of BPF programs.
config NET_DEVLINK
bool
default n
page_pool: refurbish version of page_pool code Need a fast page recycle mechanism for ndo_xdp_xmit API for returning pages on DMA-TX completion time, which have good cross CPU performance, given DMA-TX completion time can happen on a remote CPU. Refurbish my page_pool code, that was presented[1] at MM-summit 2016. Adapted page_pool code to not depend the page allocator and integration into struct page. The DMA mapping feature is kept, even-though it will not be activated/used in this patchset. [1] http://people.netfilter.org/hawk/presentations/MM-summit2016/generic_page_pool_mm_summit2016.pdf V2: Adjustments requested by Tariq - Changed page_pool_create return codes, don't return NULL, only ERR_PTR, as this simplifies err handling in drivers. V4: many small improvements and cleanups - Add DOC comment section, that can be used by kernel-doc - Improve fallback mode, to work better with refcnt based recycling e.g. remove a WARN as pointed out by Tariq e.g. quicker fallback if ptr_ring is empty. V5: Fixed SPDX license as pointed out by Alexei V6: Adjustments requested by Eric Dumazet - Adjust ____cacheline_aligned_in_smp usage/placement - Move rcu_head in struct page_pool - Free pages quicker on destroy, minimize resources delayed an RCU period - Remove code for forward/backward compat ABI interface V8: Issues found by kbuild test robot - Address sparse should be static warnings - Only compile+link when a driver use/select page_pool, mlx5 selects CONFIG_PAGE_POOL, although its first used in two patches Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-17 17:46:17 +03:00
config PAGE_POOL
bool
page_pool: refurbish version of page_pool code Need a fast page recycle mechanism for ndo_xdp_xmit API for returning pages on DMA-TX completion time, which have good cross CPU performance, given DMA-TX completion time can happen on a remote CPU. Refurbish my page_pool code, that was presented[1] at MM-summit 2016. Adapted page_pool code to not depend the page allocator and integration into struct page. The DMA mapping feature is kept, even-though it will not be activated/used in this patchset. [1] http://people.netfilter.org/hawk/presentations/MM-summit2016/generic_page_pool_mm_summit2016.pdf V2: Adjustments requested by Tariq - Changed page_pool_create return codes, don't return NULL, only ERR_PTR, as this simplifies err handling in drivers. V4: many small improvements and cleanups - Add DOC comment section, that can be used by kernel-doc - Improve fallback mode, to work better with refcnt based recycling e.g. remove a WARN as pointed out by Tariq e.g. quicker fallback if ptr_ring is empty. V5: Fixed SPDX license as pointed out by Alexei V6: Adjustments requested by Eric Dumazet - Adjust ____cacheline_aligned_in_smp usage/placement - Move rcu_head in struct page_pool - Free pages quicker on destroy, minimize resources delayed an RCU period - Remove code for forward/backward compat ABI interface V8: Issues found by kbuild test robot - Address sparse should be static warnings - Only compile+link when a driver use/select page_pool, mlx5 selects CONFIG_PAGE_POOL, although its first used in two patches Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-17 17:46:17 +03:00
config FAILOVER
tristate "Generic failover module"
help
The failover module provides a generic interface for paravirtual
drivers to register a netdev and a set of ops with a failover
instance. The ops are used as event handlers that get called to
handle netdev register/unregister/link change/name change events
on slave pci ethernet devices with the same mac address as the
failover netdev. This enables paravirtual drivers to use a
VF as an accelerated low latency datapath. It also allows live
migration of VMs with direct attached VFs by failing over to the
paravirtual datapath when the VF is unplugged.
config ETHTOOL_NETLINK
bool "Netlink interface for ethtool"
default y
help
An alternative userspace interface for ethtool based on generic
netlink. It provides better extensibility and some new features,
e.g. notification messages.
endif # if NET