WSL2-Linux-Kernel/net/8021q/vlan_core.c

154 строки
3.7 KiB
C
Исходник Обычный вид История

#include <linux/skbuff.h>
#include <linux/netdevice.h>
#include <linux/if_vlan.h>
#include <linux/netpoll.h>
#include "vlan.h"
/* VLAN rx hw acceleration helper. This acts like netif_{rx,receive_skb}(). */
int __vlan_hwaccel_rx(struct sk_buff *skb, struct vlan_group *grp,
u16 vlan_tci, int polling)
{
struct net_device *vlan_dev;
u16 vlan_id;
if (netpoll_rx(skb))
return NET_RX_DROP;
if (skb_bond_should_drop(skb, ACCESS_ONCE(skb->dev->master)))
net: deliver skbs on inactive slaves to exact matches Currently, the accelerated receive path for VLAN's will drop packets if the real device is an inactive slave and is not one of the special pkts tested for in skb_bond_should_drop(). This behavior is different then the non-accelerated path and for pkts over a bonded vlan. For example, vlanx -> bond0 -> ethx will be dropped in the vlan path and not delivered to any packet handlers at all. However, bond0 -> vlanx -> ethx and bond0 -> ethx will be delivered to handlers that match the exact dev, because the VLAN path checks the real_dev which is not a slave and netif_recv_skb() doesn't drop frames but only delivers them to exact matches. This patch adds a sk_buff flag which is used for tagging skbs that would previously been dropped and allows the skb to continue to skb_netif_recv(). Here we add logic to check for the deliver_no_wcard flag and if it is set only deliver to handlers that match exactly. This makes both paths above consistent and gives pkt handlers a way to identify skbs that come from inactive slaves. Without this patch in some configurations skbs will be delivered to handlers with exact matches and in others be dropped out right in the vlan path. I have tested the following 4 configurations in failover modes and load balancing modes. # bond0 -> ethx # vlanx -> bond0 -> ethx # bond0 -> vlanx -> ethx # bond0 -> ethx | vlanx -> -- Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 13:30:11 +04:00
skb->deliver_no_wcard = 1;
bonding: allow arp_ip_targets on separate vlans to use arp validation This allows a bond device to specify an arp_ip_target as a host that is not on the same vlan as the base bond device and still use arp validation. A configuration like this, now works: BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3" 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever 9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100 inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 ARP Polling Interval (ms): 1000 ARP IP target/s (n.n.n.n form): 10.0.100.1 Slave Interface: eth1 MII Status: up Link Failure Count: 1 Permanent HW addr: 00:40:05:30:ff:30 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:13:21:be:33:e9 Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-14 13:48:58 +03:00
skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
vlan_id = vlan_tci & VLAN_VID_MASK;
vlan_dev = vlan_group_get_device(grp, vlan_id);
if (vlan_dev)
skb->dev = vlan_dev;
else if (vlan_id)
goto drop;
return (polling ? netif_receive_skb(skb) : netif_rx(skb));
drop:
dev_kfree_skb_any(skb);
return NET_RX_DROP;
}
EXPORT_SYMBOL(__vlan_hwaccel_rx);
void vlan_hwaccel_do_receive(struct sk_buff *skb)
{
struct net_device *dev = skb->dev;
struct vlan_rx_stats *rx_stats;
skb->dev = vlan_dev_real_dev(dev);
netif_nit_deliver(skb);
skb->dev = dev;
skb->priority = vlan_get_ingress_priority(dev, skb->vlan_tci);
skb->vlan_tci = 0;
rx_stats = this_cpu_ptr(vlan_dev_info(dev)->vlan_rx_stats);
u64_stats_update_begin(&rx_stats->syncp);
rx_stats->rx_packets++;
rx_stats->rx_bytes += skb->len;
switch (skb->pkt_type) {
case PACKET_BROADCAST:
break;
case PACKET_MULTICAST:
rx_stats->rx_multicast++;
break;
case PACKET_OTHERHOST:
/* Our lower layer thinks this is not local, let's make sure.
* This allows the VLAN to have a different MAC than the
* underlying device, and still route correctly. */
if (!compare_ether_addr(eth_hdr(skb)->h_dest,
dev->dev_addr))
skb->pkt_type = PACKET_HOST;
break;
}
u64_stats_update_end(&rx_stats->syncp);
}
struct net_device *vlan_dev_real_dev(const struct net_device *dev)
{
return vlan_dev_info(dev)->real_dev;
}
EXPORT_SYMBOL(vlan_dev_real_dev);
u16 vlan_dev_vlan_id(const struct net_device *dev)
{
return vlan_dev_info(dev)->vlan_id;
}
EXPORT_SYMBOL(vlan_dev_vlan_id);
static gro_result_t
vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp,
unsigned int vlan_tci, struct sk_buff *skb)
{
struct sk_buff *p;
struct net_device *vlan_dev;
u16 vlan_id;
if (skb_bond_should_drop(skb, ACCESS_ONCE(skb->dev->master)))
net: deliver skbs on inactive slaves to exact matches Currently, the accelerated receive path for VLAN's will drop packets if the real device is an inactive slave and is not one of the special pkts tested for in skb_bond_should_drop(). This behavior is different then the non-accelerated path and for pkts over a bonded vlan. For example, vlanx -> bond0 -> ethx will be dropped in the vlan path and not delivered to any packet handlers at all. However, bond0 -> vlanx -> ethx and bond0 -> ethx will be delivered to handlers that match the exact dev, because the VLAN path checks the real_dev which is not a slave and netif_recv_skb() doesn't drop frames but only delivers them to exact matches. This patch adds a sk_buff flag which is used for tagging skbs that would previously been dropped and allows the skb to continue to skb_netif_recv(). Here we add logic to check for the deliver_no_wcard flag and if it is set only deliver to handlers that match exactly. This makes both paths above consistent and gives pkt handlers a way to identify skbs that come from inactive slaves. Without this patch in some configurations skbs will be delivered to handlers with exact matches and in others be dropped out right in the vlan path. I have tested the following 4 configurations in failover modes and load balancing modes. # bond0 -> ethx # vlanx -> bond0 -> ethx # bond0 -> vlanx -> ethx # bond0 -> ethx | vlanx -> -- Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03 13:30:11 +04:00
skb->deliver_no_wcard = 1;
bonding: allow arp_ip_targets on separate vlans to use arp validation This allows a bond device to specify an arp_ip_target as a host that is not on the same vlan as the base bond device and still use arp validation. A configuration like this, now works: BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3" 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever 9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100 inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 ARP Polling Interval (ms): 1000 ARP IP target/s (n.n.n.n form): 10.0.100.1 Slave Interface: eth1 MII Status: up Link Failure Count: 1 Permanent HW addr: 00:40:05:30:ff:30 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:13:21:be:33:e9 Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-14 13:48:58 +03:00
skb->skb_iif = skb->dev->ifindex;
__vlan_hwaccel_put_tag(skb, vlan_tci);
vlan_id = vlan_tci & VLAN_VID_MASK;
vlan_dev = vlan_group_get_device(grp, vlan_id);
if (vlan_dev)
skb->dev = vlan_dev;
else if (vlan_id)
goto drop;
for (p = napi->gro_list; p; p = p->next) {
unsigned long diffs;
diffs = (unsigned long)p->dev ^ (unsigned long)skb->dev;
diffs |= compare_ether_header(skb_mac_header(p),
skb_gro_mac_header(skb));
NAPI_GRO_CB(p)->same_flow = !diffs;
NAPI_GRO_CB(p)->flush = 0;
}
return dev_gro_receive(napi, skb);
drop:
return GRO_DROP;
}
gro_result_t vlan_gro_receive(struct napi_struct *napi, struct vlan_group *grp,
unsigned int vlan_tci, struct sk_buff *skb)
{
if (netpoll_rx_on(skb))
return vlan_hwaccel_receive_skb(skb, grp, vlan_tci)
? GRO_DROP : GRO_NORMAL;
skb_gro_reset_offset(skb);
return napi_skb_finish(vlan_gro_common(napi, grp, vlan_tci, skb), skb);
}
EXPORT_SYMBOL(vlan_gro_receive);
gro_result_t vlan_gro_frags(struct napi_struct *napi, struct vlan_group *grp,
unsigned int vlan_tci)
{
struct sk_buff *skb = napi_frags_skb(napi);
if (!skb)
return GRO_DROP;
if (netpoll_rx_on(skb)) {
skb->protocol = eth_type_trans(skb, skb->dev);
return vlan_hwaccel_receive_skb(skb, grp, vlan_tci)
? GRO_DROP : GRO_NORMAL;
}
return napi_frags_finish(napi, skb,
vlan_gro_common(napi, grp, vlan_tci, skb));
}
EXPORT_SYMBOL(vlan_gro_frags);