WSL2-Linux-Kernel/arch/powerpc/platforms/52xx/Makefile

#
# Makefile for 52xx based boards
#
ifeq ($(CONFIG_PPC_MERGE),y)
obj-y				+= mpc52xx_pic.o mpc52xx_common.o
obj-$(CONFIG_PCI)		+= mpc52xx_pci.o
endif

obj-$(CONFIG_PPC_MPC5200_SIMPLE) += mpc5200_simple.o
obj-$(CONFIG_PPC_EFIKA)		+= efika.o
obj-$(CONFIG_PPC_LITE5200)	+= lite5200.o

obj-$(CONFIG_PM)		+= mpc52xx_sleep.o mpc52xx_pm.o
ifeq ($(CONFIG_PPC_LITE5200),y)
	obj-$(CONFIG_PM)	+= lite5200_sleep.o lite5200_pm.o
endif
[POWERPC] Move MPC52xx PIC driver into arch/powerpc/platforms/52xx No other chips use this device, it belongs in a 52xx-specific path. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-11-28 00:16:23 +03:00			`#`
			`# Makefile for 52xx based boards`
			`#`
			`ifeq ($(CONFIG_PPC_MERGE),y)`
[POWERPC] Add common routines for 52xx support in arch/powerpc Adds utility routines used by 52xx device drivers and board support code. Main functionality is to add device nodes to the of_platform_bus, retrieve the IPB bus frequency, and find+ioremap device registers. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-11-28 00:16:27 +03:00			`obj-y += mpc52xx_pic.o mpc52xx_common.o`
[POWERPC] Add mpc52xx/lite5200 PCI support Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-12-13 01:13:19 +03:00			`obj-$(CONFIG_PCI) += mpc52xx_pci.o`
[POWERPC] Move MPC52xx PIC driver into arch/powerpc/platforms/52xx No other chips use this device, it belongs in a 52xx-specific path. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-11-28 00:16:23 +03:00			`endif`
[POWERPC] Move Efika support files into platforms/52xx The Efika board isn't different enough from other 52xx based boards to justify a separate platform. This patch merges it with the support code for all other 52xx based boards. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-11-28 00:16:25 +03:00
[POWERPC] mpc5200: Add generic support for simple MPC5200 based boards This patch adds support for 'mpc5200-simple-platform' compatible boards which do not need a platform specific setup. Such boards are supported assuming the following: - GPIO pins are configured by the firmware, - CDM configuration (clocking) is setup correctly by firmware, - if the 'fsl,has-wdt' property is present in one of the gpt nodes, then it is safe to use such gpt to reset the board, - PCI is supported if enabled in the kernel configuration and if there is a PCI bus node defined in the device tree. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> 2007-11-15 14:40:21 +03:00			`obj-$(CONFIG_PPC_MPC5200_SIMPLE) += mpc5200_simple.o`
[POWERPC] Small cleanup of EFIKA platform The efika platform used three files efika-pci.c efika-setup.c and a 2 line efika.h to link the two. The total of code in those is really not much and therefore, I think they're better merged in a single file. There is absolutely _no_code_change_ at all, just merged the files. Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org> 2007-02-13 01:13:24 +03:00			`obj-$(CONFIG_PPC_EFIKA) += efika.o`
[POWERPC] Add lite5200 board support to arch/powerpc Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2006-11-28 00:16:28 +03:00			`obj-$(CONFIG_PPC_LITE5200) += lite5200.o`
[POWERPC] mpc52xx suspend to deep-sleep Implement deep-sleep on MPC52xx. SDRAM is put into self-refresh with help of SRAM code (alternatives would be code in FLASH, I-cache). Interrupt code must also not be in SDRAM, so put it in I-cache. MPC52xx core is static, so contents will remain intact even with clocks turned off. Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2007-05-06 19:38:52 +04:00
			`obj-$(CONFIG_PM) += mpc52xx_sleep.o mpc52xx_pm.o`
[POWERPC] MPC5200 low power mode Low-power mode implementation for Lite5200b. Some I/O registers are also saved here. A recent U-Boot that supports this (lite5200b_PM_config) is needed. Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org> 2007-07-18 00:32:31 +04:00			`ifeq ($(CONFIG_PPC_LITE5200),y)`
			`obj-$(CONFIG_PM) += lite5200_sleep.o lite5200_pm.o`
			`endif`