144 строки
4.8 KiB
ArmAsm
144 строки
4.8 KiB
ArmAsm
|
/*
|
||
|
|
* linux/arch/arm/mach-omap2/sleep.S
|
||
|
|
*
|
||
|
|
* (C) Copyright 2004
|
||
|
|
* Texas Instruments, <www.ti.com>
|
||
|
|
* Richard Woodruff <r-woodruff2@ti.com>
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or
|
||
|
|
* modify it under the terms of the GNU General Public License as
|
||
|
|
* published by the Free Software Foundation; either version 2 of
|
||
|
|
* the License, or (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program; if not, write to the Free Software
|
||
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
||
|
|
* MA 02111-1307 USA
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <linux/linkage.h>
|
||
|
|
#include <asm/assembler.h>
|
||
|
|
#include <asm/arch/io.h>
|
||
|
|
#include <asm/arch/pm.h>
|
||
|
|
|
||
|
|
#define A_32KSYNC_CR_V IO_ADDRESS(OMAP_TIMER32K_BASE+0x10)
|
||
|
|
#define A_PRCM_VOLTCTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x50)
|
||
|
|
#define A_PRCM_CLKCFG_CTRL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x80)
|
||
|
|
#define A_CM_CLKEN_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x500)
|
||
|
|
#define A_CM_IDLEST_CKGEN_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x520)
|
||
|
|
#define A_CM_CLKSEL1_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x540)
|
||
|
|
#define A_CM_CLKSEL2_PLL_V IO_ADDRESS(OMAP24XX_PRCM_BASE+0x544)
|
||
|
|
|
||
|
|
#define A_SDRC_DLLA_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x60)
|
||
|
|
#define A_SDRC_POWER_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0x70)
|
||
|
|
#define A_SDRC_RFR_CTRL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA4)
|
||
|
|
#define A_SDRC0_V (0xC0000000)
|
||
|
|
#define A_SDRC_MANUAL_V IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA8)
|
||
|
|
|
||
|
|
.text
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Forces OMAP into idle state
|
||
|
|
*
|
||
|
|
* omap24xx_idle_loop_suspend() - This bit of code just executes the WFI
|
||
|
|
* for normal idles.
|
||
|
|
*
|
||
|
|
* Note: This code get's copied to internal SRAM at boot. When the OMAP
|
||
|
|
* wakes up it continues execution at the point it went to sleep.
|
||
|
|
*/
|
||
|
|
ENTRY(omap24xx_idle_loop_suspend)
|
||
|
|
stmfd sp!, {r0, lr} @ save registers on stack
|
||
|
|
mov r0, #0 @ clear for mcr setup
|
||
|
|
mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
|
||
|
|
ldmfd sp!, {r0, pc} @ restore regs and return
|
||
|
|
|
||
|
|
ENTRY(omap24xx_idle_loop_suspend_sz)
|
||
|
|
.word . - omap24xx_idle_loop_suspend
|
||
|
|
|
||
|
|
/*
|
||
|
|
* omap242x_cpu_suspend() - Forces OMAP into deep sleep state by completing
|
||
|
|
* SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
|
||
|
|
* SDRC.
|
||
|
|
*
|
||
|
|
* Input:
|
||
|
|
* R0 : DLL ctrl value pre-Sleep
|
||
|
|
* R1 : Processor+Revision
|
||
|
|
* 2420: 0x21 = 242xES1, 0x26 = 242xES2.2
|
||
|
|
* 2430: 0x31 = 2430ES1, 0x32 = 2430ES2
|
||
|
|
*
|
||
|
|
* The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
|
||
|
|
* when we get called, but the DLL probably isn't. We will wait a bit more in
|
||
|
|
* case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
|
||
|
|
* if in unlocked mode.
|
||
|
|
*
|
||
|
|
* For less than 242x-ES2.2 upon wake from a sleep mode where the external
|
||
|
|
* oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
|
||
|
|
* clock can pass into the PRCM can cause problems at DSP and IVA.
|
||
|
|
* To work around this the code will switch to the 32kHz source prior to sleep.
|
||
|
|
* Post sleep we will shift back to using the DPLL. Apparently,
|
||
|
|
* CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
|
||
|
|
* 3x12MHz + 3x32kHz clocks for a full switch.
|
||
|
|
*
|
||
|
|
* The DLL load value is not kept in RETENTION or OFF. It needs to be restored
|
||
|
|
* at wake
|
||
|
|
*/
|
||
|
|
ENTRY(omap24xx_cpu_suspend)
|
||
|
|
stmfd sp!, {r0 - r12, lr} @ save registers on stack
|
||
|
|
mov r3, #0x0 @ clear for mrc call
|
||
|
|
mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
|
||
|
|
nop
|
||
|
|
nop
|
||
|
|
ldr r3, A_SDRC_POWER @ addr of sdrc power
|
||
|
|
ldr r4, [r3] @ value of sdrc power
|
||
|
|
orr r4, r4, #0x40 @ enable self refresh on idle req
|
||
|
|
mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
|
||
|
|
str r4, [r3] @ make it so
|
||
|
|
mov r2, #0
|
||
|
|
nop
|
||
|
|
mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
|
||
|
|
nop
|
||
|
|
loop:
|
||
|
|
subs r5, r5, #0x1 @ awake, wait just a bit
|
||
|
|
bne loop
|
||
|
|
|
||
|
|
/* The DPLL has on before we take the DDR out of self refresh */
|
||
|
|
bic r4, r4, #0x40 @ now clear self refresh bit.
|
||
|
|
str r4, [r3] @ put vlaue back.
|
||
|
|
ldr r4, A_SDRC0 @ make a clock happen
|
||
|
|
ldr r4, [r4]
|
||
|
|
nop @ start auto refresh only after clk ok
|
||
|
|
movs r0, r0 @ see if DDR or SDR
|
||
|
|
ldrne r1, A_SDRC_DLLA_CTRL_S @ get addr of DLL ctrl
|
||
|
|
strne r0, [r1] @ rewrite DLLA to force DLL reload
|
||
|
|
addne r1, r1, #0x8 @ move to DLLB
|
||
|
|
strne r0, [r1] @ rewrite DLLB to force DLL reload
|
||
|
|
|
||
|
|
mov r5, #0x1000
|
||
|
|
loop2:
|
||
|
|
subs r5, r5, #0x1
|
||
|
|
bne loop2
|
||
|
|
/* resume*/
|
||
|
|
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
|
||
|
|
|
||
|
|
A_SDRC_POWER:
|
||
|
|
.word A_SDRC_POWER_V
|
||
|
|
A_SDRC0:
|
||
|
|
.word A_SDRC0_V
|
||
|
|
A_CM_CLKSEL2_PLL_S:
|
||
|
|
.word A_CM_CLKSEL2_PLL_V
|
||
|
|
A_CM_CLKEN_PLL:
|
||
|
|
.word A_CM_CLKEN_PLL_V
|
||
|
|
A_SDRC_DLLA_CTRL_S:
|
||
|
|
.word A_SDRC_DLLA_CTRL_V
|
||
|
|
A_SDRC_MANUAL_S:
|
||
|
|
.word A_SDRC_MANUAL_V
|
||
|
|
|
||
|
|
ENTRY(omap24xx_cpu_suspend_sz)
|
||
|
|
.word . - omap24xx_cpu_suspend
|
||
|
|
|