Input: pmic8xxx-pwrkey - support shutdown
On pm8xxx PMICs, shutdown and restart are signaled to the PMIC via a pin called PS_HOLD. When this pin goes low, the PMIC performs a configurable power sequence. Add a .shutdown hook so that we can properly configure this power sequence for shutdown or restart depending on the system state. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit is contained in:
Stephen Boyd
Dmitry Torokhov
Родитель
c57d5621d2
Коммит
02b0b79c30
|
|
@ -20,17 +20,72 @@
|
|||
#include <linux/regmap.h>
|
||||
#include <linux/log2.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_device.h>
|
||||
|
||||
#define PON_CNTL_1 0x1C
|
||||
#define PON_CNTL_PULL_UP BIT(7)
|
||||
#define PON_CNTL_TRIG_DELAY_MASK (0x7)
|
||||
#define PON_CNTL_1_PULL_UP_EN 0xe0
|
||||
#define PON_CNTL_1_USB_PWR_EN 0x10
|
||||
#define PON_CNTL_1_WD_EN_RESET 0x08
|
||||
|
||||
#define PM8058_SLEEP_CTRL 0x02b
|
||||
#define PM8921_SLEEP_CTRL 0x10a
|
||||
|
||||
#define SLEEP_CTRL_SMPL_EN_RESET 0x04
|
||||
|
||||
/* Regulator master enable addresses */
|
||||
#define REG_PM8058_VREG_EN_MSM 0x018
|
||||
#define REG_PM8058_VREG_EN_GRP_5_4 0x1c8
|
||||
|
||||
/* Regulator control registers for shutdown/reset */
|
||||
#define PM8058_S0_CTRL 0x004
|
||||
#define PM8058_S1_CTRL 0x005
|
||||
#define PM8058_S3_CTRL 0x111
|
||||
#define PM8058_L21_CTRL 0x120
|
||||
#define PM8058_L22_CTRL 0x121
|
||||
|
||||
#define PM8058_REGULATOR_ENABLE_MASK 0x80
|
||||
#define PM8058_REGULATOR_ENABLE 0x80
|
||||
#define PM8058_REGULATOR_DISABLE 0x00
|
||||
#define PM8058_REGULATOR_PULL_DOWN_MASK 0x40
|
||||
#define PM8058_REGULATOR_PULL_DOWN_EN 0x40
|
||||
|
||||
/* Buck CTRL register */
|
||||
#define PM8058_SMPS_LEGACY_VREF_SEL 0x20
|
||||
#define PM8058_SMPS_LEGACY_VPROG_MASK 0x1f
|
||||
#define PM8058_SMPS_ADVANCED_BAND_MASK 0xC0
|
||||
#define PM8058_SMPS_ADVANCED_BAND_SHIFT 6
|
||||
#define PM8058_SMPS_ADVANCED_VPROG_MASK 0x3f
|
||||
|
||||
/* Buck TEST2 registers for shutdown/reset */
|
||||
#define PM8058_S0_TEST2 0x084
|
||||
#define PM8058_S1_TEST2 0x085
|
||||
#define PM8058_S3_TEST2 0x11a
|
||||
|
||||
#define PM8058_REGULATOR_BANK_WRITE 0x80
|
||||
#define PM8058_REGULATOR_BANK_MASK 0x70
|
||||
#define PM8058_REGULATOR_BANK_SHIFT 4
|
||||
#define PM8058_REGULATOR_BANK_SEL(n) ((n) << PM8058_REGULATOR_BANK_SHIFT)
|
||||
|
||||
/* Buck TEST2 register bank 1 */
|
||||
#define PM8058_SMPS_LEGACY_VLOW_SEL 0x01
|
||||
|
||||
/* Buck TEST2 register bank 7 */
|
||||
#define PM8058_SMPS_ADVANCED_MODE_MASK 0x02
|
||||
#define PM8058_SMPS_ADVANCED_MODE 0x02
|
||||
#define PM8058_SMPS_LEGACY_MODE 0x00
|
||||
|
||||
/**
|
||||
* struct pmic8xxx_pwrkey - pmic8xxx pwrkey information
|
||||
* @key_press_irq: key press irq number
|
||||
* @regmap: device regmap
|
||||
* @shutdown_fn: shutdown configuration function
|
||||
*/
|
||||
struct pmic8xxx_pwrkey {
|
||||
int key_press_irq;
|
||||
struct regmap *regmap;
|
||||
int (*shutdown_fn)(struct pmic8xxx_pwrkey *, bool);
|
||||
};
|
||||
|
||||
static irqreturn_t pwrkey_press_irq(int irq, void *_pwr)
|
||||
|
|
@ -76,6 +131,212 @@ static int __maybe_unused pmic8xxx_pwrkey_resume(struct device *dev)
|
|||
static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops,
|
||||
pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);
|
||||
|
||||
static void pmic8xxx_pwrkey_shutdown(struct platform_device *pdev)
|
||||
{
|
||||
struct pmic8xxx_pwrkey *pwrkey = platform_get_drvdata(pdev);
|
||||
int error;
|
||||
u8 mask, val;
|
||||
bool reset = system_state == SYSTEM_RESTART;
|
||||
|
||||
if (pwrkey->shutdown_fn) {
|
||||
error = pwrkey->shutdown_fn(pwrkey, reset);
|
||||
if (error)
|
||||
return;
|
||||
}
|
||||
|
||||
/*
|
||||
* Select action to perform (reset or shutdown) when PS_HOLD goes low.
|
||||
* Also ensure that KPD, CBL0, and CBL1 pull ups are enabled and that
|
||||
* USB charging is enabled.
|
||||
*/
|
||||
mask = PON_CNTL_1_PULL_UP_EN | PON_CNTL_1_USB_PWR_EN;
|
||||
mask |= PON_CNTL_1_WD_EN_RESET;
|
||||
val = mask;
|
||||
if (!reset)
|
||||
val &= ~PON_CNTL_1_WD_EN_RESET;
|
||||
|
||||
regmap_update_bits(pwrkey->regmap, PON_CNTL_1, mask, val);
|
||||
}
|
||||
|
||||
/*
|
||||
* Set an SMPS regulator to be disabled in its CTRL register, but enabled
|
||||
* in the master enable register. Also set it's pull down enable bit.
|
||||
* Take care to make sure that the output voltage doesn't change if switching
|
||||
* from advanced mode to legacy mode.
|
||||
*/
|
||||
static int pm8058_disable_smps_locally_set_pull_down(struct regmap *regmap,
|
||||
u16 ctrl_addr, u16 test2_addr, u16 master_enable_addr,
|
||||
u8 master_enable_bit)
|
||||
{
|
||||
int error;
|
||||
u8 vref_sel, vlow_sel, band, vprog, bank;
|
||||
unsigned int reg;
|
||||
|
||||
bank = PM8058_REGULATOR_BANK_SEL(7);
|
||||
error = regmap_write(regmap, test2_addr, bank);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
error = regmap_read(regmap, test2_addr, ®);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
reg &= PM8058_SMPS_ADVANCED_MODE_MASK;
|
||||
/* Check if in advanced mode. */
|
||||
if (reg == PM8058_SMPS_ADVANCED_MODE) {
|
||||
/* Determine current output voltage. */
|
||||
error = regmap_read(regmap, ctrl_addr, ®);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
band = reg & PM8058_SMPS_ADVANCED_BAND_MASK;
|
||||
band >>= PM8058_SMPS_ADVANCED_BAND_SHIFT;
|
||||
switch (band) {
|
||||
case 3:
|
||||
vref_sel = 0;
|
||||
vlow_sel = 0;
|
||||
break;
|
||||
case 2:
|
||||
vref_sel = PM8058_SMPS_LEGACY_VREF_SEL;
|
||||
vlow_sel = 0;
|
||||
break;
|
||||
case 1:
|
||||
vref_sel = PM8058_SMPS_LEGACY_VREF_SEL;
|
||||
vlow_sel = PM8058_SMPS_LEGACY_VLOW_SEL;
|
||||
break;
|
||||
default:
|
||||
pr_err("%s: regulator already disabled\n", __func__);
|
||||
return -EPERM;
|
||||
}
|
||||
vprog = reg & PM8058_SMPS_ADVANCED_VPROG_MASK;
|
||||
/* Round up if fine step is in use. */
|
||||
vprog = (vprog + 1) >> 1;
|
||||
if (vprog > PM8058_SMPS_LEGACY_VPROG_MASK)
|
||||
vprog = PM8058_SMPS_LEGACY_VPROG_MASK;
|
||||
|
||||
/* Set VLOW_SEL bit. */
|
||||
bank = PM8058_REGULATOR_BANK_SEL(1);
|
||||
error = regmap_write(regmap, test2_addr, bank);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
error = regmap_update_bits(regmap, test2_addr,
|
||||
PM8058_REGULATOR_BANK_WRITE | PM8058_REGULATOR_BANK_MASK
|
||||
| PM8058_SMPS_LEGACY_VLOW_SEL,
|
||||
PM8058_REGULATOR_BANK_WRITE |
|
||||
PM8058_REGULATOR_BANK_SEL(1) | vlow_sel);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
/* Switch to legacy mode */
|
||||
bank = PM8058_REGULATOR_BANK_SEL(7);
|
||||
error = regmap_write(regmap, test2_addr, bank);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
error = regmap_update_bits(regmap, test2_addr,
|
||||
PM8058_REGULATOR_BANK_WRITE |
|
||||
PM8058_REGULATOR_BANK_MASK |
|
||||
PM8058_SMPS_ADVANCED_MODE_MASK,
|
||||
PM8058_REGULATOR_BANK_WRITE |
|
||||
PM8058_REGULATOR_BANK_SEL(7) |
|
||||
PM8058_SMPS_LEGACY_MODE);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
/* Enable locally, enable pull down, keep voltage the same. */
|
||||
error = regmap_update_bits(regmap, ctrl_addr,
|
||||
PM8058_REGULATOR_ENABLE_MASK |
|
||||
PM8058_REGULATOR_PULL_DOWN_MASK |
|
||||
PM8058_SMPS_LEGACY_VREF_SEL |
|
||||
PM8058_SMPS_LEGACY_VPROG_MASK,
|
||||
PM8058_REGULATOR_ENABLE | PM8058_REGULATOR_PULL_DOWN_EN
|
||||
| vref_sel | vprog);
|
||||
if (error)
|
||||
return error;
|
||||
}
|
||||
|
||||
/* Enable in master control register. */
|
||||
error = regmap_update_bits(regmap, master_enable_addr,
|
||||
master_enable_bit, master_enable_bit);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
/* Disable locally and enable pull down. */
|
||||
return regmap_update_bits(regmap, ctrl_addr,
|
||||
PM8058_REGULATOR_ENABLE_MASK | PM8058_REGULATOR_PULL_DOWN_MASK,
|
||||
PM8058_REGULATOR_DISABLE | PM8058_REGULATOR_PULL_DOWN_EN);
|
||||
}
|
||||
|
||||
static int pm8058_disable_ldo_locally_set_pull_down(struct regmap *regmap,
|
||||
u16 ctrl_addr, u16 master_enable_addr, u8 master_enable_bit)
|
||||
{
|
||||
int error;
|
||||
|
||||
/* Enable LDO in master control register. */
|
||||
error = regmap_update_bits(regmap, master_enable_addr,
|
||||
master_enable_bit, master_enable_bit);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
/* Disable LDO in CTRL register and set pull down */
|
||||
return regmap_update_bits(regmap, ctrl_addr,
|
||||
PM8058_REGULATOR_ENABLE_MASK | PM8058_REGULATOR_PULL_DOWN_MASK,
|
||||
PM8058_REGULATOR_DISABLE | PM8058_REGULATOR_PULL_DOWN_EN);
|
||||
}
|
||||
|
||||
static int pm8058_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset)
|
||||
{
|
||||
int error;
|
||||
struct regmap *regmap = pwrkey->regmap;
|
||||
u8 mask, val;
|
||||
|
||||
/* When shutting down, enable active pulldowns on important rails. */
|
||||
if (!reset) {
|
||||
/* Disable SMPS's 0,1,3 locally and set pulldown enable bits. */
|
||||
pm8058_disable_smps_locally_set_pull_down(regmap,
|
||||
PM8058_S0_CTRL, PM8058_S0_TEST2,
|
||||
REG_PM8058_VREG_EN_MSM, BIT(7));
|
||||
pm8058_disable_smps_locally_set_pull_down(regmap,
|
||||
PM8058_S1_CTRL, PM8058_S1_TEST2,
|
||||
REG_PM8058_VREG_EN_MSM, BIT(6));
|
||||
pm8058_disable_smps_locally_set_pull_down(regmap,
|
||||
PM8058_S3_CTRL, PM8058_S3_TEST2,
|
||||
REG_PM8058_VREG_EN_GRP_5_4, BIT(7) | BIT(4));
|
||||
/* Disable LDO 21 locally and set pulldown enable bit. */
|
||||
pm8058_disable_ldo_locally_set_pull_down(regmap,
|
||||
PM8058_L21_CTRL, REG_PM8058_VREG_EN_GRP_5_4,
|
||||
BIT(1));
|
||||
}
|
||||
|
||||
/*
|
||||
* Fix-up: Set regulator LDO22 to 1.225 V in high power mode. Leave its
|
||||
* pull-down state intact. This ensures a safe shutdown.
|
||||
*/
|
||||
error = regmap_update_bits(regmap, PM8058_L22_CTRL, 0xbf, 0x93);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
/* Enable SMPL if resetting is desired */
|
||||
mask = SLEEP_CTRL_SMPL_EN_RESET;
|
||||
val = 0;
|
||||
if (reset)
|
||||
val = mask;
|
||||
return regmap_update_bits(regmap, PM8058_SLEEP_CTRL, mask, val);
|
||||
}
|
||||
|
||||
static int pm8921_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset)
|
||||
{
|
||||
struct regmap *regmap = pwrkey->regmap;
|
||||
u8 mask = SLEEP_CTRL_SMPL_EN_RESET;
|
||||
u8 val = 0;
|
||||
|
||||
/* Enable SMPL if resetting is desired */
|
||||
if (reset)
|
||||
val = mask;
|
||||
return regmap_update_bits(regmap, PM8921_SLEEP_CTRL, mask, val);
|
||||
}
|
||||
|
||||
static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct input_dev *pwr;
|
||||
|
|
@ -109,6 +370,8 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
|
|||
if (!pwrkey)
|
||||
return -ENOMEM;
|
||||
|
||||
pwrkey->shutdown_fn = of_device_get_match_data(&pdev->dev);
|
||||
pwrkey->regmap = regmap;
|
||||
pwrkey->key_press_irq = key_press_irq;
|
||||
|
||||
pwr = devm_input_allocate_device(&pdev->dev);
|
||||
|
|
@ -182,8 +445,8 @@ static int pmic8xxx_pwrkey_remove(struct platform_device *pdev)
|
|||
}
|
||||
|
||||
static const struct of_device_id pm8xxx_pwr_key_id_table[] = {
|
||||
{ .compatible = "qcom,pm8058-pwrkey" },
|
||||
{ .compatible = "qcom,pm8921-pwrkey" },
|
||||
{ .compatible = "qcom,pm8058-pwrkey", .data = &pm8058_pwrkey_shutdown },
|
||||
{ .compatible = "qcom,pm8921-pwrkey", .data = &pm8921_pwrkey_shutdown },
|
||||
{ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
|
||||
|
|
@ -191,6 +454,7 @@ MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
|
|||
static struct platform_driver pmic8xxx_pwrkey_driver = {
|
||||
.probe = pmic8xxx_pwrkey_probe,
|
||||
.remove = pmic8xxx_pwrkey_remove,
|
||||
.shutdown = pmic8xxx_pwrkey_shutdown,
|
||||
.driver = {
|
||||
.name = "pm8xxx-pwrkey",
|
||||
.pm = &pm8xxx_pwr_key_pm_ops,
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче