hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
ADM1177 is a Hot Swap Controller and Digital Power Monitor with Soft Start Pin. Datasheet: Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf Signed-off-by: Beniamin Bia <beniamin.bia@analog.com> Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit is contained in:
Beniamin Bia
Guenter Roeck
Родитель
971dfd8cdc
Коммит
09b08ac9e8
|
|
@ -0,0 +1,36 @@
|
|||
Kernel driver adm1177
|
||||
=====================
|
||||
|
||||
Supported chips:
|
||||
* Analog Devices ADM1177
|
||||
Prefix: 'adm1177'
|
||||
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
|
||||
|
||||
Author: Beniamin Bia <beniamin.bia@analog.com>
|
||||
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
This driver supports hardware monitoring for Analog Devices ADM1177
|
||||
Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
|
||||
|
||||
|
||||
Usage Notes
|
||||
-----------
|
||||
|
||||
This driver does not auto-detect devices. You will have to instantiate the
|
||||
devices explicitly. Please see Documentation/i2c/instantiating-devices for
|
||||
details.
|
||||
|
||||
|
||||
Sysfs entries
|
||||
-------------
|
||||
|
||||
The following attributes are supported. Current maxim attribute
|
||||
is read-write, all other attributes are read-only.
|
||||
|
||||
in0_input Measured voltage in microvolts.
|
||||
|
||||
curr1_input Measured current in microamperes.
|
||||
curr1_max_alarm Overcurrent alarm in microamperes.
|
||||
|
|
@ -29,6 +29,7 @@ Hardware Monitoring Kernel Drivers
|
|||
adm1025
|
||||
adm1026
|
||||
adm1031
|
||||
adm1177
|
||||
adm1275
|
||||
adm9240
|
||||
ads7828
|
||||
|
|
|
|||
|
|
@ -164,6 +164,16 @@ config SENSORS_ADM1031
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called adm1031.
|
||||
|
||||
config SENSORS_ADM1177
|
||||
tristate "Analog Devices ADM1177 and compatibles"
|
||||
depends on I2C
|
||||
help
|
||||
If you say yes here you get support for Analog Devices ADM1177
|
||||
sensor chips.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called adm1177.
|
||||
|
||||
config SENSORS_ADM9240
|
||||
tristate "Analog Devices ADM9240 and compatibles"
|
||||
depends on I2C
|
||||
|
|
|
|||
|
|
@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
|
|||
obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o
|
||||
obj-$(CONFIG_SENSORS_ADM1029) += adm1029.o
|
||||
obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
|
||||
obj-$(CONFIG_SENSORS_ADM1177) += adm1177.o
|
||||
obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o
|
||||
obj-$(CONFIG_SENSORS_ADS7828) += ads7828.o
|
||||
obj-$(CONFIG_SENSORS_ADS7871) += ads7871.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,288 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* ADM1177 Hot Swap Controller and Digital Power Monitor with Soft Start Pin
|
||||
*
|
||||
* Copyright 2015-2019 Analog Devices Inc.
|
||||
*/
|
||||
|
||||
#include <linux/bits.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/hwmon.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/regulator/consumer.h>
|
||||
|
||||
/* Command Byte Operations */
|
||||
#define ADM1177_CMD_V_CONT BIT(0)
|
||||
#define ADM1177_CMD_I_CONT BIT(2)
|
||||
#define ADM1177_CMD_VRANGE BIT(4)
|
||||
|
||||
/* Extended Register */
|
||||
#define ADM1177_REG_ALERT_TH 2
|
||||
|
||||
#define ADM1177_BITS 12
|
||||
|
||||
/**
|
||||
* struct adm1177_state - driver instance specific data
|
||||
* @client pointer to i2c client
|
||||
* @reg regulator info for the the power supply of the device
|
||||
* @r_sense_uohm current sense resistor value
|
||||
* @alert_threshold_ua current limit for shutdown
|
||||
* @vrange_high internal voltage divider
|
||||
*/
|
||||
struct adm1177_state {
|
||||
struct i2c_client *client;
|
||||
struct regulator *reg;
|
||||
u32 r_sense_uohm;
|
||||
u32 alert_threshold_ua;
|
||||
bool vrange_high;
|
||||
};
|
||||
|
||||
static int adm1177_read_raw(struct adm1177_state *st, u8 num, u8 *data)
|
||||
{
|
||||
return i2c_master_recv(st->client, data, num);
|
||||
}
|
||||
|
||||
static int adm1177_write_cmd(struct adm1177_state *st, u8 cmd)
|
||||
{
|
||||
return i2c_smbus_write_byte(st->client, cmd);
|
||||
}
|
||||
|
||||
static int adm1177_write_alert_thr(struct adm1177_state *st,
|
||||
u32 alert_threshold_ua)
|
||||
{
|
||||
u64 val;
|
||||
int ret;
|
||||
|
||||
val = 0xFFULL * alert_threshold_ua * st->r_sense_uohm;
|
||||
val = div_u64(val, 105840000U);
|
||||
val = div_u64(val, 1000U);
|
||||
if (val > 0xFF)
|
||||
val = 0xFF;
|
||||
|
||||
ret = i2c_smbus_write_byte_data(st->client, ADM1177_REG_ALERT_TH,
|
||||
val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
st->alert_threshold_ua = alert_threshold_ua;
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int adm1177_read(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int channel, long *val)
|
||||
{
|
||||
struct adm1177_state *st = dev_get_drvdata(dev);
|
||||
u8 data[3];
|
||||
long dummy;
|
||||
int ret;
|
||||
|
||||
switch (type) {
|
||||
case hwmon_curr:
|
||||
switch (attr) {
|
||||
case hwmon_curr_input:
|
||||
ret = adm1177_read_raw(st, 3, data);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
dummy = (data[1] << 4) | (data[2] & 0xF);
|
||||
/*
|
||||
* convert to milliamperes
|
||||
* ((105.84mV / 4096) x raw) / senseResistor(ohm)
|
||||
*/
|
||||
*val = div_u64((105840000ull * dummy),
|
||||
4096 * st->r_sense_uohm);
|
||||
return 0;
|
||||
case hwmon_curr_max_alarm:
|
||||
*val = st->alert_threshold_ua;
|
||||
return 0;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
case hwmon_in:
|
||||
ret = adm1177_read_raw(st, 3, data);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
dummy = (data[0] << 4) | (data[2] >> 4);
|
||||
/*
|
||||
* convert to millivolts based on resistor devision
|
||||
* (V_fullscale / 4096) * raw
|
||||
*/
|
||||
if (st->vrange_high)
|
||||
dummy *= 26350;
|
||||
else
|
||||
dummy *= 6650;
|
||||
|
||||
*val = DIV_ROUND_CLOSEST(dummy, 4096);
|
||||
return 0;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
}
|
||||
|
||||
static int adm1177_write(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int channel, long val)
|
||||
{
|
||||
struct adm1177_state *st = dev_get_drvdata(dev);
|
||||
|
||||
switch (type) {
|
||||
case hwmon_curr:
|
||||
switch (attr) {
|
||||
case hwmon_curr_max_alarm:
|
||||
adm1177_write_alert_thr(st, val);
|
||||
return 0;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
}
|
||||
|
||||
static umode_t adm1177_is_visible(const void *data,
|
||||
enum hwmon_sensor_types type,
|
||||
u32 attr, int channel)
|
||||
{
|
||||
const struct adm1177_state *st = data;
|
||||
|
||||
switch (type) {
|
||||
case hwmon_in:
|
||||
switch (attr) {
|
||||
case hwmon_in_input:
|
||||
return 0444;
|
||||
}
|
||||
break;
|
||||
case hwmon_curr:
|
||||
switch (attr) {
|
||||
case hwmon_curr_input:
|
||||
if (st->r_sense_uohm)
|
||||
return 0444;
|
||||
return 0;
|
||||
case hwmon_curr_max_alarm:
|
||||
if (st->r_sense_uohm)
|
||||
return 0644;
|
||||
return 0;
|
||||
}
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct hwmon_channel_info *adm1177_info[] = {
|
||||
HWMON_CHANNEL_INFO(curr,
|
||||
HWMON_C_INPUT | HWMON_C_MAX_ALARM),
|
||||
HWMON_CHANNEL_INFO(in,
|
||||
HWMON_I_INPUT),
|
||||
NULL
|
||||
};
|
||||
|
||||
static const struct hwmon_ops adm1177_hwmon_ops = {
|
||||
.is_visible = adm1177_is_visible,
|
||||
.read = adm1177_read,
|
||||
.write = adm1177_write,
|
||||
};
|
||||
|
||||
static const struct hwmon_chip_info adm1177_chip_info = {
|
||||
.ops = &adm1177_hwmon_ops,
|
||||
.info = adm1177_info,
|
||||
};
|
||||
|
||||
static void adm1177_remove(void *data)
|
||||
{
|
||||
struct adm1177_state *st = data;
|
||||
|
||||
regulator_disable(st->reg);
|
||||
}
|
||||
|
||||
static int adm1177_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct device *dev = &client->dev;
|
||||
struct device *hwmon_dev;
|
||||
struct adm1177_state *st;
|
||||
u32 alert_threshold_ua;
|
||||
int ret;
|
||||
|
||||
st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL);
|
||||
if (!st)
|
||||
return -ENOMEM;
|
||||
|
||||
st->client = client;
|
||||
|
||||
st->reg = devm_regulator_get_optional(&client->dev, "vref");
|
||||
if (IS_ERR(st->reg)) {
|
||||
if (PTR_ERR(st->reg) == -EPROBE_DEFER)
|
||||
return -EPROBE_DEFER;
|
||||
|
||||
st->reg = NULL;
|
||||
} else {
|
||||
ret = regulator_enable(st->reg);
|
||||
if (ret)
|
||||
return ret;
|
||||
ret = devm_add_action_or_reset(&client->dev, adm1177_remove,
|
||||
st);
|
||||
if (ret)
|
||||
return ret;
|
||||
}
|
||||
|
||||
if (device_property_read_u32(dev, "shunt-resistor-micro-ohms",
|
||||
&st->r_sense_uohm))
|
||||
st->r_sense_uohm = 0;
|
||||
if (device_property_read_u32(dev, "adi,shutdown-threshold-microamp",
|
||||
&alert_threshold_ua)) {
|
||||
if (st->r_sense_uohm)
|
||||
/*
|
||||
* set maximum default value from datasheet based on
|
||||
* shunt-resistor
|
||||
*/
|
||||
alert_threshold_ua = div_u64(105840000000,
|
||||
st->r_sense_uohm);
|
||||
else
|
||||
alert_threshold_ua = 0;
|
||||
}
|
||||
st->vrange_high = device_property_read_bool(dev,
|
||||
"adi,vrange-high-enable");
|
||||
if (alert_threshold_ua && st->r_sense_uohm)
|
||||
adm1177_write_alert_thr(st, alert_threshold_ua);
|
||||
|
||||
ret = adm1177_write_cmd(st, ADM1177_CMD_V_CONT |
|
||||
ADM1177_CMD_I_CONT |
|
||||
(st->vrange_high ? 0 : ADM1177_CMD_VRANGE));
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
hwmon_dev =
|
||||
devm_hwmon_device_register_with_info(dev, client->name, st,
|
||||
&adm1177_chip_info, NULL);
|
||||
return PTR_ERR_OR_ZERO(hwmon_dev);
|
||||
}
|
||||
|
||||
static const struct i2c_device_id adm1177_id[] = {
|
||||
{"adm1177", 0},
|
||||
{}
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, adm1177_id);
|
||||
|
||||
static const struct of_device_id adm1177_dt_ids[] = {
|
||||
{ .compatible = "adi,adm1177" },
|
||||
{},
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, adm1177_dt_ids);
|
||||
|
||||
static struct i2c_driver adm1177_driver = {
|
||||
.class = I2C_CLASS_HWMON,
|
||||
.driver = {
|
||||
.name = "adm1177",
|
||||
.of_match_table = adm1177_dt_ids,
|
||||
},
|
||||
.probe = adm1177_probe,
|
||||
.id_table = adm1177_id,
|
||||
};
|
||||
module_i2c_driver(adm1177_driver);
|
||||
|
||||
MODULE_AUTHOR("Beniamin Bia <beniamin.bia@analog.com>");
|
||||
MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>");
|
||||
MODULE_DESCRIPTION("Analog Devices ADM1177 ADC driver");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
Загрузка…
Ссылка в новой задаче