ASoC: fsl_sai: Add indentation for binding doc to increase readability

This patch refines the DT binding doc for more readability by adding
extra blank lines and indentations.

Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Documentation/devicetree/bindings/sound/fsl-sai.txt

@@ -5,32 +5,48 @@ which provides a synchronous audio interface that supports fullduplex
 serial interfaces with frame synchronization such as I2S, AC97, TDM, and
 codec/DSP interfaces.
 
-
 Required properties:
-- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai".
-- reg: Offset and length of the register set for the device.
-- clocks: Must contain an entry for each entry in clock-names.
-- clock-names : Must include the "bus" for register access and "mclk1" "mclk2"
-  "mclk3" for bit clock and frame clock providing.
-- dmas : Generic dma devicetree binding as described in
-  Documentation/devicetree/bindings/dma/dma.txt.
-- dma-names : Two dmas have to be defined, "tx" and "rx".
-- pinctrl-names: Must contain a "default" entry.
-- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
-  See ../pinctrl/pinctrl-bindings.txt for details of the property values.
-- big-endian: Boolean property, required if all the FTM_PWM registers
-  are big-endian rather than little-endian.
-- lsb-first: Configures whether the LSB or the MSB is transmitted first for
-  the fifo data. If this property is absent, the MSB is transmitted first as
-  default, or the LSB is transmitted first.
-- fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
-  that SAI will work in the synchronous mode (sync Tx with Rx) which means
-  both the transimitter and receiver will send and receive data by following
-  receiver's bit clocks and frame sync clocks.
-- fsl,sai-asynchronous: This is a boolean property. If present, indicating
-  that SAI will work in the asynchronous mode, which means both transimitter
-  and receiver will send and receive data by following their own bit clocks
-  and frame sync clocks separately.
+
+  - compatible		: Compatible list, contains "fsl,vf610-sai" or
+			  "fsl,imx6sx-sai".
+
+  - reg			: Offset and length of the register set for the device.
+
+  - clocks		: Must contain an entry for each entry in clock-names.
+
+  - clock-names		: Must include the "bus" for register access and
+			  "mclk1", "mclk2", "mclk3" for bit clock and frame
+			  clock providing.
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
+
+  - pinctrl-names	: Must contain a "default" entry.
+
+  - pinctrl-NNN		: One property must exist for each entry in
+			  pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
+			  for details of the property values.
+
+  - big-endian		: Boolean property, required if all the FTM_PWM
+			  registers are big-endian rather than little-endian.
+
+  - lsb-first		: Configures whether the LSB or the MSB is transmitted
+			  first for the fifo data. If this property is absent,
+			  the MSB is transmitted first as default, or the LSB
+			  is transmitted first.
+
+  - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
+			  that SAI will work in the synchronous mode (sync Tx
+			  with Rx) which means both the transimitter and the
+			  receiver will send and receive data by following
+			  receiver's bit clocks and frame sync clocks.
+
+  - fsl,sai-asynchronous: This is a boolean property. If present, indicating
+			  that SAI will work in the asynchronous mode, which
+			  means both transimitter and receiver will send and
+			  receive data by following their own bit clocks and
+			  frame sync clocks separately.
 
 Note:
 - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the