ARM: dts: sun7i: Add dts file for Bananapro board
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit is contained in:
Hans de Goede
Maxime Ripard
Родитель
121b96cd9d
Коммит
10662a33dc
|
|
@ -465,6 +465,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
|
|||
sun6i-a31s-cs908.dtb
|
||||
dtb-$(CONFIG_MACH_SUN7I) += \
|
||||
sun7i-a20-bananapi.dtb \
|
||||
sun7i-a20-bananapro.dtb \
|
||||
sun7i-a20-cubieboard2.dtb \
|
||||
sun7i-a20-cubietruck.dtb \
|
||||
sun7i-a20-hummingbird.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,262 @@
|
|||
/*
|
||||
* Copyright 2015 Hans de Goede <hdegoede@redhat.com>
|
||||
*
|
||||
* This file is dual-licensed: you can use it either under the terms
|
||||
* of the GPL or the X11 license, at your option. Note that this dual
|
||||
* licensing only applies to this file, and not this project as a
|
||||
* whole.
|
||||
*
|
||||
* a) This file is free software; you can redistribute it and/or
|
||||
* modify it under the terms of the GNU General Public License as
|
||||
* published by the Free Software Foundation; either version 2 of the
|
||||
* License, or (at your option) any later version.
|
||||
*
|
||||
* This file is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public
|
||||
* License along with this file; if not, write to the Free
|
||||
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
|
||||
* MA 02110-1301 USA
|
||||
*
|
||||
* Or, alternatively,
|
||||
*
|
||||
* b) Permission is hereby granted, free of charge, to any person
|
||||
* obtaining a copy of this software and associated documentation
|
||||
* files (the "Software"), to deal in the Software without
|
||||
* restriction, including without limitation the rights to use,
|
||||
* copy, modify, merge, publish, distribute, sublicense, and/or
|
||||
* sell copies of the Software, and to permit persons to whom the
|
||||
* Software is furnished to do so, subject to the following
|
||||
* conditions:
|
||||
*
|
||||
* The above copyright notice and this permission notice shall be
|
||||
* included in all copies or substantial portions of the Software.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
|
||||
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
|
||||
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
|
||||
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
|
||||
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
|
||||
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
|
||||
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
|
||||
* OTHER DEALINGS IN THE SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "sun7i-a20.dtsi"
|
||||
#include "sunxi-common-regulators.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
|
||||
/ {
|
||||
model = "LeMaker Banana Pro";
|
||||
compatible = "lemaker,bananapro", "allwinner,sun7i-a20";
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&led_pins_bananapro>;
|
||||
|
||||
blue {
|
||||
label = "bananapro:blue:usr";
|
||||
gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
green {
|
||||
label = "bananapro:green:usr";
|
||||
gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
reg_gmac_3v3: gmac-3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gmac_power_pin_bananapro>;
|
||||
regulator-name = "gmac-3v3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
startup-delay-us = <100000>;
|
||||
enable-active-high;
|
||||
gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
reg_vmmc3: vmmc3 {
|
||||
compatible = "regulator-fixed";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vmmc3_pin_bananapro>;
|
||||
regulator-name = "vmmc3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
enable-active-high;
|
||||
gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&ahci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ehci0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ehci1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gmac_pins_rgmii_a>;
|
||||
phy = <&phy1>;
|
||||
phy-mode = "rgmii";
|
||||
phy-supply = <®_gmac_3v3>;
|
||||
status = "okay";
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c0_pins_a>;
|
||||
status = "okay";
|
||||
|
||||
axp209: pmic@34 {
|
||||
compatible = "x-powers,axp209";
|
||||
reg = <0x34>;
|
||||
interrupt-parent = <&nmi_intc>;
|
||||
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ir0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ir0_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
|
||||
vmmc-supply = <®_vcc3v3>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
|
||||
cd-inverted;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mmc3 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc3_pins_a>;
|
||||
vmmc-supply = <®_vmmc3>;
|
||||
bus-width = <4>;
|
||||
non-removable;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pio {
|
||||
gmac_power_pin_bananapro: gmac_power_pin@0 {
|
||||
allwinner,pins = "PH23";
|
||||
allwinner,function = "gpio_out";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
|
||||
};
|
||||
|
||||
led_pins_bananapro: led_pins@0 {
|
||||
allwinner,pins = "PH24", "PG2";
|
||||
allwinner,function = "gpio_out";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
|
||||
};
|
||||
|
||||
mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
|
||||
allwinner,pins = "PH10";
|
||||
allwinner,function = "gpio_in";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
|
||||
};
|
||||
|
||||
usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
|
||||
allwinner,pins = "PH0";
|
||||
allwinner,function = "gpio_out";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
|
||||
};
|
||||
|
||||
usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
|
||||
allwinner,pins = "PH1";
|
||||
allwinner,function = "gpio_out";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
|
||||
};
|
||||
|
||||
vmmc3_pin_bananapro: vmmc3_pin@0 {
|
||||
allwinner,pins = "PH22";
|
||||
allwinner,function = "gpio_out";
|
||||
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
|
||||
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
|
||||
};
|
||||
};
|
||||
|
||||
®_usb1_vbus {
|
||||
pinctrl-0 = <&usb1_vbus_pin_bananapro>;
|
||||
gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
®_usb2_vbus {
|
||||
pinctrl-0 = <&usb2_vbus_pin_bananapro>;
|
||||
gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart2_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart7 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart7_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy {
|
||||
usb1_vbus-supply = <®_usb1_vbus>;
|
||||
usb2_vbus-supply = <®_usb2_vbus>;
|
||||
status = "okay";
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче