[POWERPC] mpc5200: Amalgamated DTS fixes and updates
DTS updates that fix booting problems on mpc5200-based boards: - change to ethernet reg property - addition of mdio and phy nodes - removal of pci node (Motion-Pro board) Other DTS updates: - update i2c device tree nodes - add lpb bus node and flash device (without partitions defined) - add rtc i2c nodes Signed-off-by: Marian Balakowicz <m8@semihalf.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
This commit is contained in:
Bartlomiej Sieka
Paul Mackerras
Родитель
7484839850
Коммит
115e1adca3
|
|
@ -212,13 +212,30 @@
|
|||
ethernet@3000 {
|
||||
device_type = "network";
|
||||
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
|
||||
reg = <3000 800>;
|
||||
reg = <3000 400>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
interrupts = <2 5 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
mdio@3000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
|
||||
reg = <3000 400>; // fec range, since we need to setup fec interrupts
|
||||
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c@3d40 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
|
||||
reg = <3d40 40>;
|
||||
interrupts = <2 10 0>;
|
||||
|
|
@ -231,4 +248,22 @@
|
|||
reg = <8000 4000>;
|
||||
};
|
||||
};
|
||||
|
||||
lpb {
|
||||
model = "fsl,lpb";
|
||||
compatible = "fsl,lpb";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <1>;
|
||||
ranges = <0 0 fc000000 2000000>;
|
||||
|
||||
// 16-bit flash device at LocalPlus Bus CS0
|
||||
flash@0,0 {
|
||||
compatible = "cfi-flash";
|
||||
reg = <0 0 2000000>;
|
||||
bank-width = <2>;
|
||||
device-width = <2>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
|
|||
|
|
@ -148,7 +148,6 @@
|
|||
interrupt-parent = <&mpc5200_pic>;
|
||||
};
|
||||
|
||||
|
||||
spi@f00 {
|
||||
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
|
||||
reg = <f00 20>;
|
||||
|
|
@ -209,10 +208,25 @@
|
|||
ethernet@3000 {
|
||||
device_type = "network";
|
||||
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
|
||||
reg = <3000 800>;
|
||||
reg = <3000 400>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
interrupts = <2 5 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
mdio@3000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
|
||||
reg = <3000 400>; // fec range, since we need to setup fec interrupts
|
||||
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
|
||||
phy0: ethernet-phy@2 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
ata@3a00 {
|
||||
|
|
@ -223,11 +237,19 @@
|
|||
};
|
||||
|
||||
i2c@3d40 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
|
||||
reg = <3d40 40>;
|
||||
interrupts = <2 10 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
fsl5200-clocking;
|
||||
|
||||
rtc@68 {
|
||||
device_type = "rtc";
|
||||
compatible = "dallas,ds1339";
|
||||
reg = <68>;
|
||||
};
|
||||
};
|
||||
|
||||
sram@8000 {
|
||||
|
|
@ -240,7 +262,8 @@
|
|||
compatible = "fsl,lpb";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <1>;
|
||||
ranges = <1 0 50000000 00010000
|
||||
ranges = <0 0 ff000000 01000000
|
||||
1 0 50000000 00010000
|
||||
2 0 50010000 00010000
|
||||
3 0 50020000 00010000>;
|
||||
|
||||
|
|
@ -271,31 +294,15 @@
|
|||
compatible = "promess,pro_module_dio";
|
||||
reg = <3 800 2>;
|
||||
};
|
||||
|
||||
// 16-bit flash device at LocalPlus Bus CS0
|
||||
flash@0,0 {
|
||||
compatible = "cfi-flash";
|
||||
reg = <0 0 01000000>;
|
||||
bank-width = <2>;
|
||||
device-width = <2>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <1>;
|
||||
};
|
||||
|
||||
pci@f0000d00 {
|
||||
#interrupt-cells = <1>;
|
||||
#size-cells = <2>;
|
||||
#address-cells = <3>;
|
||||
device_type = "pci";
|
||||
compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
|
||||
reg = <f0000d00 100>;
|
||||
interrupt-map-mask = <f800 0 0 7>;
|
||||
interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
|
||||
c000 0 0 2 &mpc5200_pic 1 1 3
|
||||
c000 0 0 3 &mpc5200_pic 1 2 3
|
||||
c000 0 0 4 &mpc5200_pic 1 3 3
|
||||
|
||||
c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
|
||||
c800 0 0 2 &mpc5200_pic 1 2 3
|
||||
c800 0 0 3 &mpc5200_pic 1 3 3
|
||||
c800 0 0 4 &mpc5200_pic 0 0 3>;
|
||||
clock-frequency = <0>; // From boot loader
|
||||
interrupts = <2 8 0 2 9 0 2 a 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
bus-range = <0 0>;
|
||||
ranges = <42000000 0 80000000 80000000 0 20000000
|
||||
02000000 0 a0000000 a0000000 0 10000000
|
||||
01000000 0 00000000 b0000000 0 01000000>;
|
||||
};
|
||||
};
|
||||
|
|
|
|||
|
|
@ -127,10 +127,25 @@
|
|||
ethernet@3000 {
|
||||
device_type = "network";
|
||||
compatible = "fsl,mpc5200-fec";
|
||||
reg = <3000 800>;
|
||||
reg = <3000 400>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
interrupts = <2 5 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
mdio@3000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
|
||||
reg = <3000 400>; // fec range, since we need to setup fec interrupts
|
||||
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ata@3a00 {
|
||||
|
|
@ -141,11 +156,19 @@
|
|||
};
|
||||
|
||||
i2c@3d40 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "fsl,mpc5200-i2c","fsl-i2c";
|
||||
reg = <3d40 40>;
|
||||
interrupts = <2 10 0>;
|
||||
interrupt-parent = <&mpc5200_pic>;
|
||||
fsl5200-clocking;
|
||||
|
||||
rtc@68 {
|
||||
device_type = "rtc";
|
||||
compatible = "dallas,ds1307";
|
||||
reg = <68>;
|
||||
};
|
||||
};
|
||||
|
||||
sram@8000 {
|
||||
|
|
@ -154,6 +177,23 @@
|
|||
};
|
||||
};
|
||||
|
||||
lpb {
|
||||
model = "fsl,lpb";
|
||||
compatible = "fsl,lpb";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <1>;
|
||||
ranges = <0 0 fc000000 02000000>;
|
||||
|
||||
flash@0,0 {
|
||||
compatible = "cfi-flash";
|
||||
reg = <0 0 02000000>;
|
||||
bank-width = <4>;
|
||||
device-width = <2>;
|
||||
#size-cells = <1>;
|
||||
#address-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
pci@f0000d00 {
|
||||
#interrupt-cells = <1>;
|
||||
#size-cells = <2>;
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче