MIPS: mscc: add DT for Ocelot PCB120

The Ocelot PCB120 evaluation board is different from the PCB123 in that
it has 4 external VSC8584 (or VSC8574) PHYs.

It uses the SoC's second MDIO bus for external PHYs which have a
reversed address on the bus (i.e. PHY4 is on address 3, PHY5 is on
address 2, PHY6 on 1 and PHY7 on 0).

Here is how the PHYs are connected to the switch ports:
port 0: phy0 (internal)
port 1: phy1 (internal)
port 2: phy2 (internal)
port 3: phy3 (internal)
port 4: phy7
port 5: phy4
port 6: phy6
port 9: phy5

Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20869/
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: davem@davemloft.net
Cc: andrew@lunn.ch
Cc: f.fainelli@gmail.com
Cc: allan.nielsen@microchip.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: thomas.petazzoni@bootlin.com
Cc: antoine.tenart@bootlin.com

arch/mips/boot/dts/mscc/Makefile

@@ -1,3 +1,3 @@
-dtb-$(CONFIG_MSCC_OCELOT)	+= ocelot_pcb123.dtb
+dtb-$(CONFIG_MSCC_OCELOT)	+= ocelot_pcb123.dtb ocelot_pcb120.dtb
 
 obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))

arch/mips/boot/dts/mscc/ocelot_pcb120.dts

@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy-ocelot-serdes.h>
+#include "ocelot.dtsi"
+
+/ {
+	compatible = "mscc,ocelot-pcb120", "mscc,ocelot";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0e000000>;
+	};
+};
+
+&gpio {
+	phy_int_pins: phy_int_pins {
+		pins = "GPIO_4";
+		function = "gpio";
+	};
+};
+
+&mdio0 {
+	status = "okay";
+};
+
+&mdio1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&miim1>, <&phy_int_pins>;
+
+	phy7: ethernet-phy@0 {
+		reg = <0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+	};
+	phy6: ethernet-phy@1 {
+		reg = <1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+	};
+	phy5: ethernet-phy@2 {
+		reg = <2>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+	};
+	phy4: ethernet-phy@3 {
+		reg = <3>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+	};
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+};
+
+&port2 {
+	phy-handle = <&phy2>;
+};
+
+&port3 {
+	phy-handle = <&phy3>;
+};
+
+&port4 {
+	phy-handle = <&phy7>;
+	phy-mode = "sgmii";
+	phys = <&serdes 4 SERDES1G(2)>;
+};
+
+&port5 {
+	phy-handle = <&phy4>;
+	phy-mode = "sgmii";
+	phys = <&serdes 5 SERDES1G(5)>;
+};
+
+&port6 {
+	phy-handle = <&phy6>;
+	phy-mode = "sgmii";
+	phys = <&serdes 6 SERDES1G(3)>;
+};
+
+&port9 {
+	phy-handle = <&phy5>;
+	phy-mode = "sgmii";
+	phys = <&serdes 9 SERDES1G(4)>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};