net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY
The DP83TD510E is an ultra-low power Ethernet physical layer transceiver that supports 10M single pair cable. This driver was tested with NXP SJA1105, STMMAC and ASIX AX88772B USB Ethernet controller. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Родитель
2013ad8836
Коммит
165cd04fe2
|
@ -342,6 +342,12 @@ config DP83869_PHY
|
|||
Currently supports the DP83869 PHY. This PHY supports copper and
|
||||
fiber connections.
|
||||
|
||||
config DP83TD510_PHY
|
||||
tristate "Texas Instruments DP83TD510 Ethernet 10Base-T1L PHY"
|
||||
help
|
||||
Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports
|
||||
a 10M single pair Ethernet connection for up to 1000 meter cable.
|
||||
|
||||
config VITESSE_PHY
|
||||
tristate "Vitesse PHYs"
|
||||
help
|
||||
|
|
|
@ -57,6 +57,7 @@ obj-$(CONFIG_DP83848_PHY) += dp83848.o
|
|||
obj-$(CONFIG_DP83867_PHY) += dp83867.o
|
||||
obj-$(CONFIG_DP83869_PHY) += dp83869.o
|
||||
obj-$(CONFIG_DP83TC811_PHY) += dp83tc811.o
|
||||
obj-$(CONFIG_DP83TD510_PHY) += dp83td510.o
|
||||
obj-$(CONFIG_FIXED_PHY) += fixed_phy.o
|
||||
obj-$(CONFIG_ICPLUS_PHY) += icplus.o
|
||||
obj-$(CONFIG_INTEL_XWAY_PHY) += intel-xway.o
|
||||
|
|
|
@ -0,0 +1,209 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/* Driver for the Texas Instruments DP83TD510 PHY
|
||||
* Copyright (c) 2022 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
|
||||
*/
|
||||
|
||||
#include <linux/bitfield.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/phy.h>
|
||||
|
||||
#define DP83TD510E_PHY_ID 0x20000181
|
||||
|
||||
/* MDIO_MMD_VEND2 registers */
|
||||
#define DP83TD510E_PHY_STS 0x10
|
||||
#define DP83TD510E_STS_MII_INT BIT(7)
|
||||
#define DP83TD510E_LINK_STATUS BIT(0)
|
||||
|
||||
#define DP83TD510E_GEN_CFG 0x11
|
||||
#define DP83TD510E_GENCFG_INT_POLARITY BIT(3)
|
||||
#define DP83TD510E_GENCFG_INT_EN BIT(1)
|
||||
#define DP83TD510E_GENCFG_INT_OE BIT(0)
|
||||
|
||||
#define DP83TD510E_INTERRUPT_REG_1 0x12
|
||||
#define DP83TD510E_INT1_LINK BIT(13)
|
||||
#define DP83TD510E_INT1_LINK_EN BIT(5)
|
||||
|
||||
#define DP83TD510E_AN_STAT_1 0x60c
|
||||
#define DP83TD510E_MASTER_SLAVE_RESOL_FAIL BIT(15)
|
||||
|
||||
static int dp83td510_config_intr(struct phy_device *phydev)
|
||||
{
|
||||
int ret;
|
||||
|
||||
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
|
||||
/* Clear any pending interrupts */
|
||||
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS,
|
||||
0x0);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
|
||||
DP83TD510E_INTERRUPT_REG_1,
|
||||
DP83TD510E_INT1_LINK_EN);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2,
|
||||
DP83TD510E_GEN_CFG,
|
||||
DP83TD510E_GENCFG_INT_POLARITY |
|
||||
DP83TD510E_GENCFG_INT_EN |
|
||||
DP83TD510E_GENCFG_INT_OE);
|
||||
} else {
|
||||
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
|
||||
DP83TD510E_INTERRUPT_REG_1, 0x0);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2,
|
||||
DP83TD510E_GEN_CFG,
|
||||
DP83TD510E_GENCFG_INT_EN);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/* Clear any pending interrupts */
|
||||
ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS,
|
||||
0x0);
|
||||
}
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static irqreturn_t dp83td510_handle_interrupt(struct phy_device *phydev)
|
||||
{
|
||||
int ret;
|
||||
|
||||
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_PHY_STS);
|
||||
if (ret < 0) {
|
||||
phy_error(phydev);
|
||||
return IRQ_NONE;
|
||||
} else if (!(ret & DP83TD510E_STS_MII_INT)) {
|
||||
return IRQ_NONE;
|
||||
}
|
||||
|
||||
/* Read the current enabled interrupts */
|
||||
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TD510E_INTERRUPT_REG_1);
|
||||
if (ret < 0) {
|
||||
phy_error(phydev);
|
||||
return IRQ_NONE;
|
||||
} else if (!(ret & DP83TD510E_INT1_LINK_EN) ||
|
||||
!(ret & DP83TD510E_INT1_LINK)) {
|
||||
return IRQ_NONE;
|
||||
}
|
||||
|
||||
phy_trigger_machine(phydev);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int dp83td510_read_status(struct phy_device *phydev)
|
||||
{
|
||||
u16 phy_sts;
|
||||
int ret;
|
||||
|
||||
phydev->speed = SPEED_UNKNOWN;
|
||||
phydev->duplex = DUPLEX_UNKNOWN;
|
||||
phydev->pause = 0;
|
||||
phydev->asym_pause = 0;
|
||||
linkmode_zero(phydev->lp_advertising);
|
||||
|
||||
phy_sts = phy_read(phydev, DP83TD510E_PHY_STS);
|
||||
|
||||
phydev->link = !!(phy_sts & DP83TD510E_LINK_STATUS);
|
||||
if (phydev->link) {
|
||||
/* This PHY supports only one link mode: 10BaseT1L_Full */
|
||||
phydev->duplex = DUPLEX_FULL;
|
||||
phydev->speed = SPEED_10;
|
||||
|
||||
if (phydev->autoneg == AUTONEG_ENABLE) {
|
||||
ret = genphy_c45_read_lpa(phydev);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
phy_resolve_aneg_linkmode(phydev);
|
||||
}
|
||||
}
|
||||
|
||||
if (phydev->autoneg == AUTONEG_ENABLE) {
|
||||
ret = genphy_c45_baset1_read_status(phydev);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
|
||||
DP83TD510E_AN_STAT_1);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
if (ret & DP83TD510E_MASTER_SLAVE_RESOL_FAIL)
|
||||
phydev->master_slave_state = MASTER_SLAVE_STATE_ERR;
|
||||
} else {
|
||||
return genphy_c45_pma_baset1_read_master_slave(phydev);
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int dp83td510_config_aneg(struct phy_device *phydev)
|
||||
{
|
||||
bool changed = false;
|
||||
int ret;
|
||||
|
||||
ret = genphy_c45_pma_baset1_setup_master_slave(phydev);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
if (phydev->autoneg == AUTONEG_DISABLE)
|
||||
return genphy_c45_an_disable_aneg(phydev);
|
||||
|
||||
ret = genphy_c45_an_config_aneg(phydev);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
if (ret > 0)
|
||||
changed = true;
|
||||
|
||||
return genphy_c45_check_and_restart_aneg(phydev, changed);
|
||||
}
|
||||
|
||||
static int dp83td510_get_features(struct phy_device *phydev)
|
||||
{
|
||||
/* This PHY can't respond on MDIO bus if no RMII clock is enabled.
|
||||
* In case RMII mode is used (most meaningful mode for this PHY) and
|
||||
* the PHY do not have own XTAL, and CLK providing MAC is not probed,
|
||||
* we won't be able to read all needed ability registers.
|
||||
* So provide it manually.
|
||||
*/
|
||||
|
||||
linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
|
||||
linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->supported);
|
||||
linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->supported);
|
||||
linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
|
||||
phydev->supported);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct phy_driver dp83td510_driver[] = {
|
||||
{
|
||||
PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID),
|
||||
.name = "TI DP83TD510E",
|
||||
|
||||
.config_aneg = dp83td510_config_aneg,
|
||||
.read_status = dp83td510_read_status,
|
||||
.get_features = dp83td510_get_features,
|
||||
.config_intr = dp83td510_config_intr,
|
||||
.handle_interrupt = dp83td510_handle_interrupt,
|
||||
|
||||
.suspend = genphy_suspend,
|
||||
.resume = genphy_resume,
|
||||
} };
|
||||
module_phy_driver(dp83td510_driver);
|
||||
|
||||
static struct mdio_device_id __maybe_unused dp83td510_tbl[] = {
|
||||
{ PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID) },
|
||||
{ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(mdio, dp83td510_tbl);
|
||||
|
||||
MODULE_DESCRIPTION("Texas Instruments DP83TD510E PHY driver");
|
||||
MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
|
||||
MODULE_LICENSE("GPL v2");
|
Загрузка…
Ссылка в новой задаче