Merge remote-tracking branch 'asoc/topic/wm8962' into asoc-next

This commit is contained in:
Mark Brown 2013-11-08 10:43:42 +00:00
Родитель 552b747564 ae2ff9f6c5
Коммит 22b468a06e
1 изменённых файлов: 116 добавлений и 110 удалений

Просмотреть файл

@ -1758,6 +1758,9 @@ SOC_DOUBLE_R_TLV("EQ4 Volume", WM8962_EQ3, WM8962_EQ23,
WM8962_EQL_B4_GAIN_SHIFT, 31, 0, eq_tlv),
SOC_DOUBLE_R_TLV("EQ5 Volume", WM8962_EQ3, WM8962_EQ23,
WM8962_EQL_B5_GAIN_SHIFT, 31, 0, eq_tlv),
SND_SOC_BYTES("EQL Coefficients", WM8962_EQ4, 18),
SND_SOC_BYTES("EQR Coefficients", WM8962_EQ24, 18),
SOC_SINGLE("3D Switch", WM8962_THREED1, 0, 1, 0),
SND_SOC_BYTES_MASK("3D Coefficients", WM8962_THREED1, 4, WM8962_THREED_ENA),
@ -1775,6 +1778,11 @@ WM8962_DSP2_ENABLE("HPF2 Switch", WM8962_HPF2_ENA_SHIFT),
SND_SOC_BYTES("HPF Coefficients", WM8962_LHPF2, 1),
WM8962_DSP2_ENABLE("HD Bass Switch", WM8962_HDBASS_ENA_SHIFT),
SND_SOC_BYTES("HD Bass Coefficients", WM8962_HDBASS_AI_1, 30),
SOC_DOUBLE("ALC Switch", WM8962_ALC1, WM8962_ALCL_ENA_SHIFT,
WM8962_ALCR_ENA_SHIFT, 1, 0),
SND_SOC_BYTES_MASK("ALC Coefficients", WM8962_ALC1, 4,
WM8962_ALCL_ENA_MASK | WM8962_ALCR_ENA_MASK),
};
static const struct snd_kcontrol_new wm8962_spk_mono_controls[] = {
@ -3242,7 +3250,7 @@ static void wm8962_free_beep(struct snd_soc_codec *codec)
}
#endif
static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio)
static void wm8962_set_gpio_mode(struct wm8962_priv *wm8962, int gpio)
{
int mask = 0;
int val = 0;
@ -3263,8 +3271,8 @@ static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio)
}
if (mask)
snd_soc_update_bits(codec, WM8962_ANALOGUE_CLOCKING1,
mask, val);
regmap_update_bits(wm8962->regmap, WM8962_ANALOGUE_CLOCKING1,
mask, val);
}
#ifdef CONFIG_GPIOLIB
@ -3276,7 +3284,6 @@ static inline struct wm8962_priv *gpio_to_wm8962(struct gpio_chip *chip)
static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset)
{
struct wm8962_priv *wm8962 = gpio_to_wm8962(chip);
struct snd_soc_codec *codec = wm8962->codec;
/* The WM8962 GPIOs aren't linearly numbered. For simplicity
* we export linear numbers and error out if the unsupported
@ -3292,7 +3299,7 @@ static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset)
return -EINVAL;
}
wm8962_set_gpio_mode(codec, offset + 1);
wm8962_set_gpio_mode(wm8962, offset + 1);
return 0;
}
@ -3376,8 +3383,7 @@ static int wm8962_probe(struct snd_soc_codec *codec)
{
int ret;
struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
struct wm8962_pdata *pdata = &wm8962->pdata;
int i, trigger, irq_pol;
int i;
bool dmicclk, dmicdat;
wm8962->codec = codec;
@ -3409,75 +3415,6 @@ static int wm8962_probe(struct snd_soc_codec *codec)
}
}
/* SYSCLK defaults to on; make sure it is off so we can safely
* write to registers if the device is declocked.
*/
snd_soc_update_bits(codec, WM8962_CLOCKING2, WM8962_SYSCLK_ENA, 0);
/* Ensure we have soft control over all registers */
snd_soc_update_bits(codec, WM8962_CLOCKING2,
WM8962_CLKREG_OVD, WM8962_CLKREG_OVD);
/* Ensure that the oscillator and PLLs are disabled */
snd_soc_update_bits(codec, WM8962_PLL2,
WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
0);
/* Apply static configuration for GPIOs */
for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++)
if (pdata->gpio_init[i]) {
wm8962_set_gpio_mode(codec, i + 1);
snd_soc_write(codec, 0x200 + i,
pdata->gpio_init[i] & 0xffff);
}
/* Put the speakers into mono mode? */
if (pdata->spk_mono)
snd_soc_update_bits(codec, WM8962_CLASS_D_CONTROL_2,
WM8962_SPK_MONO_MASK, WM8962_SPK_MONO);
/* Micbias setup, detection enable and detection
* threasholds. */
if (pdata->mic_cfg)
snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4,
WM8962_MICDET_ENA |
WM8962_MICDET_THR_MASK |
WM8962_MICSHORT_THR_MASK |
WM8962_MICBIAS_LVL,
pdata->mic_cfg);
/* Latch volume update bits */
snd_soc_update_bits(codec, WM8962_LEFT_INPUT_VOLUME,
WM8962_IN_VU, WM8962_IN_VU);
snd_soc_update_bits(codec, WM8962_RIGHT_INPUT_VOLUME,
WM8962_IN_VU, WM8962_IN_VU);
snd_soc_update_bits(codec, WM8962_LEFT_ADC_VOLUME,
WM8962_ADC_VU, WM8962_ADC_VU);
snd_soc_update_bits(codec, WM8962_RIGHT_ADC_VOLUME,
WM8962_ADC_VU, WM8962_ADC_VU);
snd_soc_update_bits(codec, WM8962_LEFT_DAC_VOLUME,
WM8962_DAC_VU, WM8962_DAC_VU);
snd_soc_update_bits(codec, WM8962_RIGHT_DAC_VOLUME,
WM8962_DAC_VU, WM8962_DAC_VU);
snd_soc_update_bits(codec, WM8962_SPKOUTL_VOLUME,
WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
snd_soc_update_bits(codec, WM8962_SPKOUTR_VOLUME,
WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
snd_soc_update_bits(codec, WM8962_HPOUTL_VOLUME,
WM8962_HPOUT_VU, WM8962_HPOUT_VU);
snd_soc_update_bits(codec, WM8962_HPOUTR_VOLUME,
WM8962_HPOUT_VU, WM8962_HPOUT_VU);
/* Stereo control for EQ */
snd_soc_update_bits(codec, WM8962_EQ1, WM8962_EQ_SHARED_COEFF, 0);
/* Don't debouce interrupts so we don't need SYSCLK */
snd_soc_update_bits(codec, WM8962_IRQ_DEBOUNCE,
WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB |
WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB,
0);
wm8962_add_widgets(codec);
/* Save boards having to disable DMIC when not in use */
@ -3506,36 +3443,6 @@ static int wm8962_probe(struct snd_soc_codec *codec)
wm8962_init_beep(codec);
wm8962_init_gpio(codec);
if (wm8962->irq) {
if (pdata->irq_active_low) {
trigger = IRQF_TRIGGER_LOW;
irq_pol = WM8962_IRQ_POL;
} else {
trigger = IRQF_TRIGGER_HIGH;
irq_pol = 0;
}
snd_soc_update_bits(codec, WM8962_INTERRUPT_CONTROL,
WM8962_IRQ_POL, irq_pol);
ret = request_threaded_irq(wm8962->irq, NULL, wm8962_irq,
trigger | IRQF_ONESHOT,
"wm8962", codec->dev);
if (ret != 0) {
dev_err(codec->dev, "Failed to request IRQ %d: %d\n",
wm8962->irq, ret);
wm8962->irq = 0;
/* Non-fatal */
} else {
/* Enable some IRQs by default */
snd_soc_update_bits(codec,
WM8962_INTERRUPT_STATUS_2_MASK,
WM8962_FLL_LOCK_EINT |
WM8962_TEMP_SHUT_EINT |
WM8962_FIFOS_ERR_EINT, 0);
}
}
return 0;
}
@ -3544,9 +3451,6 @@ static int wm8962_remove(struct snd_soc_codec *codec)
struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
int i;
if (wm8962->irq)
free_irq(wm8962->irq, codec);
cancel_delayed_work_sync(&wm8962->mic_work);
wm8962_free_gpio(codec);
@ -3619,7 +3523,7 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
struct wm8962_pdata *pdata = dev_get_platdata(&i2c->dev);
struct wm8962_priv *wm8962;
unsigned int reg;
int ret, i;
int ret, i, irq_pol, trigger;
wm8962 = devm_kzalloc(&i2c->dev, sizeof(struct wm8962_priv),
GFP_KERNEL);
@ -3704,6 +3608,77 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
goto err_enable;
}
/* SYSCLK defaults to on; make sure it is off so we can safely
* write to registers if the device is declocked.
*/
regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
WM8962_SYSCLK_ENA, 0);
/* Ensure we have soft control over all registers */
regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
WM8962_CLKREG_OVD, WM8962_CLKREG_OVD);
/* Ensure that the oscillator and PLLs are disabled */
regmap_update_bits(wm8962->regmap, WM8962_PLL2,
WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
0);
/* Apply static configuration for GPIOs */
for (i = 0; i < ARRAY_SIZE(wm8962->pdata.gpio_init); i++)
if (wm8962->pdata.gpio_init[i]) {
wm8962_set_gpio_mode(wm8962, i + 1);
regmap_write(wm8962->regmap, 0x200 + i,
wm8962->pdata.gpio_init[i] & 0xffff);
}
/* Put the speakers into mono mode? */
if (wm8962->pdata.spk_mono)
regmap_update_bits(wm8962->regmap, WM8962_CLASS_D_CONTROL_2,
WM8962_SPK_MONO_MASK, WM8962_SPK_MONO);
/* Micbias setup, detection enable and detection
* threasholds. */
if (wm8962->pdata.mic_cfg)
regmap_update_bits(wm8962->regmap, WM8962_ADDITIONAL_CONTROL_4,
WM8962_MICDET_ENA |
WM8962_MICDET_THR_MASK |
WM8962_MICSHORT_THR_MASK |
WM8962_MICBIAS_LVL,
wm8962->pdata.mic_cfg);
/* Latch volume update bits */
regmap_update_bits(wm8962->regmap, WM8962_LEFT_INPUT_VOLUME,
WM8962_IN_VU, WM8962_IN_VU);
regmap_update_bits(wm8962->regmap, WM8962_RIGHT_INPUT_VOLUME,
WM8962_IN_VU, WM8962_IN_VU);
regmap_update_bits(wm8962->regmap, WM8962_LEFT_ADC_VOLUME,
WM8962_ADC_VU, WM8962_ADC_VU);
regmap_update_bits(wm8962->regmap, WM8962_RIGHT_ADC_VOLUME,
WM8962_ADC_VU, WM8962_ADC_VU);
regmap_update_bits(wm8962->regmap, WM8962_LEFT_DAC_VOLUME,
WM8962_DAC_VU, WM8962_DAC_VU);
regmap_update_bits(wm8962->regmap, WM8962_RIGHT_DAC_VOLUME,
WM8962_DAC_VU, WM8962_DAC_VU);
regmap_update_bits(wm8962->regmap, WM8962_SPKOUTL_VOLUME,
WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
regmap_update_bits(wm8962->regmap, WM8962_SPKOUTR_VOLUME,
WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
regmap_update_bits(wm8962->regmap, WM8962_HPOUTL_VOLUME,
WM8962_HPOUT_VU, WM8962_HPOUT_VU);
regmap_update_bits(wm8962->regmap, WM8962_HPOUTR_VOLUME,
WM8962_HPOUT_VU, WM8962_HPOUT_VU);
/* Stereo control for EQ */
regmap_update_bits(wm8962->regmap, WM8962_EQ1,
WM8962_EQ_SHARED_COEFF, 0);
/* Don't debouce interrupts so we don't need SYSCLK */
regmap_update_bits(wm8962->regmap, WM8962_IRQ_DEBOUNCE,
WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB |
WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB,
0);
if (wm8962->pdata.in4_dc_measure) {
ret = regmap_register_patch(wm8962->regmap,
wm8962_dc_measure,
@ -3714,6 +3689,37 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
ret);
}
if (wm8962->irq) {
if (wm8962->pdata.irq_active_low) {
trigger = IRQF_TRIGGER_LOW;
irq_pol = WM8962_IRQ_POL;
} else {
trigger = IRQF_TRIGGER_HIGH;
irq_pol = 0;
}
regmap_update_bits(wm8962->regmap, WM8962_INTERRUPT_CONTROL,
WM8962_IRQ_POL, irq_pol);
ret = devm_request_threaded_irq(&i2c->dev, wm8962->irq, NULL,
wm8962_irq,
trigger | IRQF_ONESHOT,
"wm8962", &i2c->dev);
if (ret != 0) {
dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n",
wm8962->irq, ret);
wm8962->irq = 0;
/* Non-fatal */
} else {
/* Enable some IRQs by default */
regmap_update_bits(wm8962->regmap,
WM8962_INTERRUPT_STATUS_2_MASK,
WM8962_FLL_LOCK_EINT |
WM8962_TEMP_SHUT_EINT |
WM8962_FIFOS_ERR_EINT, 0);
}
}
pm_runtime_enable(&i2c->dev);
pm_request_idle(&i2c->dev);