accel/habanalabs: fix few misspelled words in the code

Run spell checker on the code and fix accordingly.

Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

drivers/accel/habanalabs/common/command_submission.c

@@ -657,7 +657,7 @@ static inline void cs_release_sob_reset_handler(struct hl_device *hdev,
 	/*
 	 * we get refcount upon reservation of signals or signal/wait cs for the
 	 * hw_sob object, and need to put it when the first staged cs
-	 * (which cotains the encaps signals) or cs signal/wait is completed.
+	 * (which contains the encaps signals) or cs signal/wait is completed.
 	 */
 	if ((hl_cs_cmpl->type == CS_TYPE_SIGNAL) ||
 			(hl_cs_cmpl->type == CS_TYPE_WAIT) ||

drivers/accel/habanalabs/common/habanalabs.h

@@ -2976,8 +2976,8 @@ struct cs_timeout_info {
  * @cq_addr: the address of the current handled command buffer
  * @cq_size: the size of the current handled command buffer
  * @cb_addr_streams_len: num of streams - actual len of cb_addr_streams array.
- *                       should be equal to 1 incase of undefined opcode
- *                       in Upper-CP (specific stream) and equal to 4 incase
+ *                       should be equal to 1 in case of undefined opcode
+ *                       in Upper-CP (specific stream) and equal to 4 in case
  *                       of undefined opcode in Lower-CP.
  * @engine_id: engine-id that the error occurred on
  * @stream_id: the stream id the error occurred on. In case the stream equals to

drivers/accel/habanalabs/common/memory.c

@@ -2230,11 +2230,11 @@ static struct hl_mmap_mem_buf_behavior hl_ts_behavior = {
  * allocate_timestamps_buffers() - allocate timestamps buffers
  * This function will allocate ts buffer that will later on be mapped to the user
  * in order to be able to read the timestamp.
- * in additon it'll allocate an extra buffer for registration management.
+ * in addition it'll allocate an extra buffer for registration management.
  * since we cannot fail during registration for out-of-memory situation, so
  * we'll prepare a pool which will be used as user interrupt nodes and instead
  * of dynamically allocating nodes while registration we'll pick the node from
- * this pool. in addtion it'll add node to the mapping hash which will be used
+ * this pool. in addition it'll add node to the mapping hash which will be used
  * to map user ts buffer to the internal kernel ts buffer.
  * @hpriv: pointer to the private data of the fd
  * @args: ioctl input

drivers/accel/habanalabs/common/memory_mgr.c

@@ -275,7 +275,7 @@ int hl_mem_mgr_mmap(struct hl_mem_mgr *mmg, struct vm_area_struct *vma,
 
 	if (atomic_cmpxchg(&buf->mmap, 0, 1)) {
 		dev_err(mmg->dev,
-			"%s, Memory mmap failed, already mmaped to user\n",
+			"%s, Memory mmap failed, already maped to user\n",
 			buf->behavior->topic);
 		rc = -EINVAL;
 		goto put_mem;

drivers/accel/habanalabs/common/mmu/mmu.c

@@ -540,8 +540,8 @@ static void hl_mmu_pa_page_with_offset(struct hl_ctx *ctx, u64 virt_addr,
 		u32 page_off;
 
 		/*
-		 * Bit arithmetics cannot be used for non power of two page
-		 * sizes. In addition, since bit arithmetics is not used,
+		 * Bit arithmetic cannot be used for non power of two page
+		 * sizes. In addition, since bit arithmetic is not used,
 		 * we cannot ignore dram base. All that shall be considered.
 		 */
 
@@ -757,7 +757,7 @@ u64 hl_mmu_get_next_hop_addr(struct hl_ctx *ctx, u64 curr_pte)
  * @mmu_prop: MMU properties.
  * @hop_idx: HOP index.
  * @hop_addr: HOP address.
- * @virt_addr: virtual address fro the translation.
+ * @virt_addr: virtual address for the translation.
  *
  * @return the matching PTE value on success, otherwise U64_MAX.
  */

drivers/accel/habanalabs/gaudi2/gaudi2_coresight.c

@@ -2657,7 +2657,7 @@ int gaudi2_coresight_init(struct hl_device *hdev)
 	/*
 	 * Mask out all the disabled binned offsets.
 	 * so when user request to configure a binned or masked out component,
-	 * driver will ignore programing it ( happens when offset value is set to 0x0 )
+	 * driver will ignore programming it ( happens when offset value is set to 0x0 )
 	 * this is being set in gaudi2_coresight_set_disabled_components
 	 */