mxser: drop ISA support
While mxser PCI cards are still around and produced (Moxa provided me with two recently), ISA cards are obsolete for a long time. I haven't seen anyone using the cards and the ISA code paths are barely tested. Hence, remove ISA support from mxser driver so that we can clean the driver up. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210618061516.662-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Jiri Slaby
Greg Kroah-Hartman
Родитель
d495dd743d
Коммит
291343676e
|
|
@ -37,8 +37,7 @@ Date: 01/21/2008
|
|||
CP-102U, CP-102UL, CP-102UF
|
||||
CP-132U-I, CP-132UL,
|
||||
CP-132, CP-132I, CP132S, CP-132IS,
|
||||
CI-132, CI-132I, CI-132IS,
|
||||
(C102H, C102HI, C102HIS, C102P, CP-102, CP-102S)
|
||||
(CP-102, CP-102S)
|
||||
|
||||
- 4 ports multiport board
|
||||
CP-104EL,
|
||||
|
|
@ -46,10 +45,7 @@ Date: 01/21/2008
|
|||
CP-134U, CP-134U-I,
|
||||
C104H/PCI, C104HS/PCI,
|
||||
CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL,
|
||||
C104H, C104HS,
|
||||
CI-104J, CI-104JS,
|
||||
CI-134, CI-134I, CI-134IS,
|
||||
(C114HI, CT-114I, C104P),
|
||||
(C114HI, CT-114I),
|
||||
POS-104UL,
|
||||
CB-114,
|
||||
CB-134I
|
||||
|
|
@ -58,8 +54,6 @@ Date: 01/21/2008
|
|||
CP-118EL, CP-168EL,
|
||||
CP-118U, CP-168U,
|
||||
C168H/PCI,
|
||||
C168H, C168HS,
|
||||
(C168P),
|
||||
CB-108
|
||||
|
||||
This driver and installation procedure have been developed upon Linux Kernel
|
||||
|
|
@ -78,9 +72,6 @@ Date: 01/21/2008
|
|||
Monitor program to observe data count and line status signals.
|
||||
- msterm A simple terminal program which is useful in testing serial
|
||||
ports.
|
||||
- io-irq.exe
|
||||
Configuration program to setup ISA boards. Please note that
|
||||
this program can only be executed under DOS.
|
||||
|
||||
All the drivers and utilities are published in form of source code under
|
||||
GNU General Public License in this version. Please refer to GNU General
|
||||
|
|
@ -112,17 +103,6 @@ Date: 01/21/2008
|
|||
3.1 Hardware installation
|
||||
=========================
|
||||
|
||||
There are two types of buses, ISA and PCI, for Smartio/Industio
|
||||
family multiport board.
|
||||
|
||||
ISA board
|
||||
---------
|
||||
|
||||
You'll have to configure CAP address, I/O address, Interrupt Vector
|
||||
as well as IRQ before installing this driver. Please refer to hardware
|
||||
installation procedure in User's Manual before proceed any further.
|
||||
Please make sure the JP1 is open after the ISA board is set properly.
|
||||
|
||||
PCI/UPCI board
|
||||
--------------
|
||||
|
||||
|
|
@ -194,16 +174,6 @@ Device naming when more than 2 boards installed
|
|||
Under Kernel 2.6 and upper, the cum Device is Obsolete. So use ttyM*
|
||||
device instead.
|
||||
|
||||
Board sequence
|
||||
--------------
|
||||
|
||||
This driver will activate ISA boards according to the parameter set
|
||||
in the driver. After all specified ISA board activated, PCI board
|
||||
will be installed in the system automatically driven.
|
||||
Therefore the board number is sorted by the CAP address of ISA boards.
|
||||
For PCI boards, their sequence will be after ISA boards and C168H/PCI
|
||||
has higher priority than C104H/PCI boards.
|
||||
|
||||
3.4 Module driver configuration
|
||||
===============================
|
||||
|
||||
|
|
@ -274,12 +244,10 @@ Board sequence
|
|||
|
||||
::
|
||||
|
||||
# modprobe mxser <argument>
|
||||
# modprobe mxser
|
||||
|
||||
will activate the module driver. You may run "lsmod" to check
|
||||
if "mxser" is activated. If the MOXA board is ISA board, the
|
||||
<argument> is needed. Please refer to section "3.4.5" for more
|
||||
information.
|
||||
if "mxser" is activated.
|
||||
|
||||
------------- Load MOXA driver on boot --------------------
|
||||
|
||||
|
|
@ -296,13 +264,6 @@ Board sequence
|
|||
achieved by rc file. We offer one "rc.mxser" file to simplify
|
||||
the procedure under "moxa/mxser/driver".
|
||||
|
||||
But if you use ISA board, please modify the "modprobe ..." command
|
||||
to add the argument (see "3.4.5" section). After modifying the
|
||||
rc.mxser, please try to execute "/moxa/mxser/driver/rc.mxser"
|
||||
manually to make sure the modification is ok. If any error
|
||||
encountered, please try to modify again. If the modification is
|
||||
completed, follow the below step.
|
||||
|
||||
Run following command for setting rc files::
|
||||
|
||||
# cd /moxa/mxser/driver
|
||||
|
|
@ -316,21 +277,6 @@ Board sequence
|
|||
|
||||
Reboot and check if moxa.o activated by "lsmod" command.
|
||||
|
||||
3.4.5. specify CAP address
|
||||
--------------------------
|
||||
|
||||
If you'd like to drive Smartio/Industio ISA boards in the system,
|
||||
you'll have to add parameter to specify CAP address of given
|
||||
board while activating "mxser.o". The format for parameters are
|
||||
as follows.::
|
||||
|
||||
modprobe mxser ioaddr=0x???,0x???,0x???,0x???
|
||||
| | | |
|
||||
| | | +- 4th ISA board
|
||||
| | +------ 3rd ISA board
|
||||
| +------------ 2nd ISA board
|
||||
+-------------------1st ISA board
|
||||
|
||||
3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x
|
||||
================================================================
|
||||
|
||||
|
|
@ -357,35 +303,7 @@ Board sequence
|
|||
# cd /usr/src/linux/drivers/char
|
||||
# ln -s /moxa/mxser/driver/mxser.c mxser.c
|
||||
|
||||
3.5.3 Add CAP address list for ISA boards.
|
||||
------------------------------------------
|
||||
|
||||
For PCI boards user, please skip this step.
|
||||
|
||||
In module mode, the CAP address for ISA board is given by
|
||||
parameter. In static driver configuration, you'll have to
|
||||
assign it within driver's source code. If you will not
|
||||
install any ISA boards, you may skip to next portion.
|
||||
The instructions to modify driver source code are as
|
||||
below.
|
||||
|
||||
a. run::
|
||||
|
||||
# cd /moxa/mxser/driver
|
||||
# vi mxser.c
|
||||
|
||||
b. Find the array mxserBoardCAP[] as below::
|
||||
|
||||
static int mxserBoardCAP[] = {0x00, 0x00, 0x00, 0x00};
|
||||
|
||||
c. Change the address within this array using vi. For
|
||||
example, to driver 2 ISA boards with CAP address
|
||||
0x280 and 0x180 as 1st and 2nd board. Just to change
|
||||
the source code as follows::
|
||||
|
||||
static int mxserBoardCAP[] = {0x280, 0x180, 0x00, 0x00};
|
||||
|
||||
3.5.4 Setup kernel configuration
|
||||
3.5.3 Setup kernel configuration
|
||||
--------------------------------
|
||||
|
||||
Configure the kernel::
|
||||
|
|
@ -398,7 +316,7 @@ Board sequence
|
|||
SmartIO support] driver with "[*]" for built-in (not "[M]"), then
|
||||
select [Exit] to exit this program.
|
||||
|
||||
3.5.5 Rebuild kernel
|
||||
3.5.4 Rebuild kernel
|
||||
--------------------
|
||||
|
||||
The following are for Linux kernel rebuilding, for your
|
||||
|
|
@ -426,14 +344,14 @@ Board sequence
|
|||
directory /usr/src/linux.
|
||||
|
||||
|
||||
3.5.6 Make tty device and special file
|
||||
3.5.5 Make tty device and special file
|
||||
--------------------------------------
|
||||
|
||||
::
|
||||
# cd /moxa/mxser/driver
|
||||
# ./msmknod
|
||||
|
||||
3.5.7 Make utility
|
||||
3.5.6 Make utility
|
||||
------------------
|
||||
|
||||
::
|
||||
|
|
@ -441,7 +359,7 @@ Board sequence
|
|||
# cd /moxa/mxser/utility
|
||||
# make clean; make install
|
||||
|
||||
3.5.8 Reboot
|
||||
3.5.7 Reboot
|
||||
------------
|
||||
|
||||
|
||||
|
|
@ -591,13 +509,6 @@ msterm - Terminal Emulation
|
|||
Each port within the same multiport board shares the same IRQ. Please set
|
||||
one IRQ (IRQ doesn't equal to zero) for one Moxa board.
|
||||
|
||||
Error msg:
|
||||
No interrupt vector be set for Moxa ISA board(CAP=xxx).
|
||||
|
||||
Solution:
|
||||
Moxa ISA board needs an interrupt vector.Please refer to user's manual
|
||||
"Hardware Installation" chapter to set interrupt vector.
|
||||
|
||||
Error msg:
|
||||
Couldn't install MOXA Smartio/Industio family driver!
|
||||
|
||||
|
|
|
|||
|
|
@ -204,7 +204,7 @@ config MOXA_INTELLIO
|
|||
|
||||
config MOXA_SMARTIO
|
||||
tristate "Moxa SmartIO support v. 2.0"
|
||||
depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
|
||||
depends on SERIAL_NONSTANDARD && PCI
|
||||
help
|
||||
Say Y here if you have a Moxa SmartIO multiport serial card and/or
|
||||
want to help develop a new version of this driver.
|
||||
|
|
|
|||
|
|
@ -70,18 +70,8 @@
|
|||
#define PCI_DEVICE_ID_CB134I 0x1341
|
||||
#define PCI_DEVICE_ID_CP138U 0x1380
|
||||
|
||||
|
||||
#define C168_ASIC_ID 1
|
||||
#define C104_ASIC_ID 2
|
||||
#define C102_ASIC_ID 0xB
|
||||
#define CI132_ASIC_ID 4
|
||||
#define CI134_ASIC_ID 3
|
||||
#define CI104J_ASIC_ID 5
|
||||
|
||||
#define MXSER_HIGHBAUD 1
|
||||
#define MXSER_HAS2 2
|
||||
|
||||
/* This is only for PCI */
|
||||
static const struct {
|
||||
int type;
|
||||
int tx_fifo;
|
||||
|
|
@ -105,14 +95,14 @@ struct mxser_cardinfo {
|
|||
};
|
||||
|
||||
static const struct mxser_cardinfo mxser_cards[] = {
|
||||
/* 0*/ { "C168 series", 8, },
|
||||
{ "C104 series", 4, },
|
||||
{ "CI-104J series", 4, },
|
||||
/* 0*/ { },
|
||||
{ },
|
||||
{ },
|
||||
{ "C168H/PCI series", 8, },
|
||||
{ "C104H/PCI series", 4, },
|
||||
/* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */
|
||||
{ "CI-132 series", 4, MXSER_HAS2 },
|
||||
{ "CI-134 series", 4, },
|
||||
/* 5*/ { },
|
||||
{ },
|
||||
{ },
|
||||
{ "CP-132 series", 2, },
|
||||
{ "CP-114 series", 4, },
|
||||
/*10*/ { "CT-114 series", 4, },
|
||||
|
|
@ -172,15 +162,12 @@ static const struct pci_device_id mxser_pcibrds[] = {
|
|||
};
|
||||
MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
|
||||
|
||||
static unsigned long ioaddr[MXSER_BOARDS];
|
||||
static int ttymajor = MXSERMAJOR;
|
||||
|
||||
/* Variables for insmod */
|
||||
|
||||
MODULE_AUTHOR("Casper Yang");
|
||||
MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
|
||||
module_param_hw_array(ioaddr, ulong, ioport, NULL, 0);
|
||||
MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board");
|
||||
module_param(ttymajor, int, 0);
|
||||
MODULE_LICENSE("GPL");
|
||||
|
||||
|
|
@ -300,7 +287,6 @@ static void mxser_enable_must_enchance_mode(unsigned long baseio)
|
|||
outb(oldlcr, baseio + UART_LCR);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
static void mxser_disable_must_enchance_mode(unsigned long baseio)
|
||||
{
|
||||
u8 oldlcr;
|
||||
|
|
@ -315,7 +301,6 @@ static void mxser_disable_must_enchance_mode(unsigned long baseio)
|
|||
outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
|
||||
outb(oldlcr, baseio + UART_LCR);
|
||||
}
|
||||
#endif
|
||||
|
||||
static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
|
||||
{
|
||||
|
|
@ -387,7 +372,6 @@ static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
|
|||
outb(oldlcr, baseio + UART_LCR);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
|
||||
{
|
||||
u8 oldlcr;
|
||||
|
|
@ -404,7 +388,6 @@ static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
|
|||
*pId = inb(baseio + MOXA_MUST_HWID_REGISTER);
|
||||
outb(oldlcr, baseio + UART_LCR);
|
||||
}
|
||||
#endif
|
||||
|
||||
static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio)
|
||||
{
|
||||
|
|
@ -483,7 +466,6 @@ static void mxser_disable_must_rx_software_flow_control(unsigned long baseio)
|
|||
outb(oldlcr, baseio + UART_LCR);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
static int CheckIsMoxaMust(unsigned long io)
|
||||
{
|
||||
u8 oldmcr, hwid;
|
||||
|
|
@ -506,7 +488,6 @@ static int CheckIsMoxaMust(unsigned long io)
|
|||
}
|
||||
return MOXA_OTHER_UART;
|
||||
}
|
||||
#endif
|
||||
|
||||
static void process_txrx_fifo(struct mxser_port *info)
|
||||
{
|
||||
|
|
@ -1398,109 +1379,6 @@ static int mxser_tiocmset(struct tty_struct *tty,
|
|||
return 0;
|
||||
}
|
||||
|
||||
static int __init mxser_program_mode(int port)
|
||||
{
|
||||
int id, i, j, n;
|
||||
|
||||
outb(0, port);
|
||||
outb(0, port);
|
||||
outb(0, port);
|
||||
(void)inb(port);
|
||||
(void)inb(port);
|
||||
outb(0, port);
|
||||
(void)inb(port);
|
||||
|
||||
id = inb(port + 1) & 0x1F;
|
||||
if ((id != C168_ASIC_ID) &&
|
||||
(id != C104_ASIC_ID) &&
|
||||
(id != C102_ASIC_ID) &&
|
||||
(id != CI132_ASIC_ID) &&
|
||||
(id != CI134_ASIC_ID) &&
|
||||
(id != CI104J_ASIC_ID))
|
||||
return -1;
|
||||
for (i = 0, j = 0; i < 4; i++) {
|
||||
n = inb(port + 2);
|
||||
if (n == 'M') {
|
||||
j = 1;
|
||||
} else if ((j == 1) && (n == 1)) {
|
||||
j = 2;
|
||||
break;
|
||||
} else
|
||||
j = 0;
|
||||
}
|
||||
if (j != 2)
|
||||
id = -2;
|
||||
return id;
|
||||
}
|
||||
|
||||
static void __init mxser_normal_mode(int port)
|
||||
{
|
||||
int i, n;
|
||||
|
||||
outb(0xA5, port + 1);
|
||||
outb(0x80, port + 3);
|
||||
outb(12, port + 0); /* 9600 bps */
|
||||
outb(0, port + 1);
|
||||
outb(0x03, port + 3); /* 8 data bits */
|
||||
outb(0x13, port + 4); /* loop back mode */
|
||||
for (i = 0; i < 16; i++) {
|
||||
n = inb(port + 5);
|
||||
if ((n & 0x61) == 0x60)
|
||||
break;
|
||||
if ((n & 1) == 1)
|
||||
(void)inb(port);
|
||||
}
|
||||
outb(0x00, port + 4);
|
||||
}
|
||||
|
||||
#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
|
||||
#define CHIP_DO 0x02 /* Serial Data Output in Eprom */
|
||||
#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
|
||||
#define CHIP_DI 0x08 /* Serial Data Input in Eprom */
|
||||
#define EN_CCMD 0x000 /* Chip's command register */
|
||||
#define EN0_RSARLO 0x008 /* Remote start address reg 0 */
|
||||
#define EN0_RSARHI 0x009 /* Remote start address reg 1 */
|
||||
#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
|
||||
#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
|
||||
#define EN0_DCFG 0x00E /* Data configuration reg WR */
|
||||
#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
|
||||
#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
|
||||
#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
|
||||
static int __init mxser_read_register(int port, unsigned short *regs)
|
||||
{
|
||||
int i, k, value, id;
|
||||
unsigned int j;
|
||||
|
||||
id = mxser_program_mode(port);
|
||||
if (id < 0)
|
||||
return id;
|
||||
for (i = 0; i < 14; i++) {
|
||||
k = (i & 0x3F) | 0x180;
|
||||
for (j = 0x100; j > 0; j >>= 1) {
|
||||
outb(CHIP_CS, port);
|
||||
if (k & j) {
|
||||
outb(CHIP_CS | CHIP_DO, port);
|
||||
outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
|
||||
} else {
|
||||
outb(CHIP_CS, port);
|
||||
outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
|
||||
}
|
||||
}
|
||||
(void)inb(port);
|
||||
value = 0;
|
||||
for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
|
||||
outb(CHIP_CS, port);
|
||||
outb(CHIP_CS | CHIP_SK, port);
|
||||
if (inb(port) & CHIP_DI)
|
||||
value |= j;
|
||||
}
|
||||
regs[i] = value;
|
||||
outb(0, port);
|
||||
}
|
||||
mxser_normal_mode(port);
|
||||
return id;
|
||||
}
|
||||
|
||||
static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
|
||||
{
|
||||
struct mxser_port *ip;
|
||||
|
|
@ -2346,37 +2224,6 @@ static const struct tty_port_operations mxser_port_ops = {
|
|||
* The MOXA Smartio/Industio serial driver boot-time initialization code!
|
||||
*/
|
||||
|
||||
static bool allow_overlapping_vector;
|
||||
module_param(allow_overlapping_vector, bool, S_IRUGO);
|
||||
MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)");
|
||||
|
||||
static bool mxser_overlapping_vector(struct mxser_board *brd)
|
||||
{
|
||||
return allow_overlapping_vector &&
|
||||
brd->vector >= brd->ports[0].ioaddr &&
|
||||
brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports;
|
||||
}
|
||||
|
||||
static int mxser_request_vector(struct mxser_board *brd)
|
||||
{
|
||||
if (mxser_overlapping_vector(brd))
|
||||
return 0;
|
||||
return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO;
|
||||
}
|
||||
|
||||
static void mxser_release_vector(struct mxser_board *brd)
|
||||
{
|
||||
if (mxser_overlapping_vector(brd))
|
||||
return;
|
||||
release_region(brd->vector, 1);
|
||||
}
|
||||
|
||||
static void mxser_release_ISA_res(struct mxser_board *brd)
|
||||
{
|
||||
release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
|
||||
mxser_release_vector(brd);
|
||||
}
|
||||
|
||||
static int mxser_initbrd(struct mxser_board *brd)
|
||||
{
|
||||
struct mxser_port *info;
|
||||
|
|
@ -2439,125 +2286,9 @@ static void mxser_board_remove(struct mxser_board *brd)
|
|||
free_irq(brd->irq, brd);
|
||||
}
|
||||
|
||||
static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
|
||||
{
|
||||
int id, i, bits, ret;
|
||||
unsigned short regs[16], irq;
|
||||
unsigned char scratch, scratch2;
|
||||
|
||||
brd->chip_flag = MOXA_OTHER_UART;
|
||||
|
||||
id = mxser_read_register(cap, regs);
|
||||
switch (id) {
|
||||
case C168_ASIC_ID:
|
||||
brd->info = &mxser_cards[0];
|
||||
break;
|
||||
case C104_ASIC_ID:
|
||||
brd->info = &mxser_cards[1];
|
||||
break;
|
||||
case CI104J_ASIC_ID:
|
||||
brd->info = &mxser_cards[2];
|
||||
break;
|
||||
case C102_ASIC_ID:
|
||||
brd->info = &mxser_cards[5];
|
||||
break;
|
||||
case CI132_ASIC_ID:
|
||||
brd->info = &mxser_cards[6];
|
||||
break;
|
||||
case CI134_ASIC_ID:
|
||||
brd->info = &mxser_cards[7];
|
||||
break;
|
||||
default:
|
||||
return 0;
|
||||
}
|
||||
|
||||
irq = 0;
|
||||
/* some ISA cards have 2 ports, but we want to see them as 4-port (why?)
|
||||
Flag-hack checks if configuration should be read as 2-port here. */
|
||||
if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) {
|
||||
irq = regs[9] & 0xF000;
|
||||
irq = irq | (irq >> 4);
|
||||
if (irq != (regs[9] & 0xFF00))
|
||||
goto err_irqconflict;
|
||||
} else if (brd->info->nports == 4) {
|
||||
irq = regs[9] & 0xF000;
|
||||
irq = irq | (irq >> 4);
|
||||
irq = irq | (irq >> 8);
|
||||
if (irq != regs[9])
|
||||
goto err_irqconflict;
|
||||
} else if (brd->info->nports == 8) {
|
||||
irq = regs[9] & 0xF000;
|
||||
irq = irq | (irq >> 4);
|
||||
irq = irq | (irq >> 8);
|
||||
if ((irq != regs[9]) || (irq != regs[10]))
|
||||
goto err_irqconflict;
|
||||
}
|
||||
|
||||
if (!irq) {
|
||||
printk(KERN_ERR "mxser: interrupt number unset\n");
|
||||
return -EIO;
|
||||
}
|
||||
brd->irq = ((int)(irq & 0xF000) >> 12);
|
||||
for (i = 0; i < 8; i++)
|
||||
brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8;
|
||||
if ((regs[12] & 0x80) == 0) {
|
||||
printk(KERN_ERR "mxser: invalid interrupt vector\n");
|
||||
return -EIO;
|
||||
}
|
||||
brd->vector = (int)regs[11]; /* interrupt vector */
|
||||
if (id == 1)
|
||||
brd->vector_mask = 0x00FF;
|
||||
else
|
||||
brd->vector_mask = 0x000F;
|
||||
for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) {
|
||||
if (regs[12] & bits) {
|
||||
brd->ports[i].baud_base = 921600;
|
||||
brd->ports[i].max_baud = 921600;
|
||||
} else {
|
||||
brd->ports[i].baud_base = 115200;
|
||||
brd->ports[i].max_baud = 115200;
|
||||
}
|
||||
}
|
||||
scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB);
|
||||
outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR);
|
||||
outb(0, cap + UART_EFR); /* EFR is the same as FCR */
|
||||
outb(scratch2, cap + UART_LCR);
|
||||
outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR);
|
||||
scratch = inb(cap + UART_IIR);
|
||||
|
||||
if (scratch & 0xC0)
|
||||
brd->uart_type = PORT_16550A;
|
||||
else
|
||||
brd->uart_type = PORT_16450;
|
||||
if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports,
|
||||
"mxser(IO)")) {
|
||||
printk(KERN_ERR "mxser: can't request ports I/O region: "
|
||||
"0x%.8lx-0x%.8lx\n",
|
||||
brd->ports[0].ioaddr, brd->ports[0].ioaddr +
|
||||
8 * brd->info->nports - 1);
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
ret = mxser_request_vector(brd);
|
||||
if (ret) {
|
||||
release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
|
||||
printk(KERN_ERR "mxser: can't request interrupt vector region: "
|
||||
"0x%.8lx-0x%.8lx\n",
|
||||
brd->ports[0].ioaddr, brd->ports[0].ioaddr +
|
||||
8 * brd->info->nports - 1);
|
||||
return ret;
|
||||
}
|
||||
return brd->info->nports;
|
||||
|
||||
err_irqconflict:
|
||||
printk(KERN_ERR "mxser: invalid interrupt number\n");
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
static int mxser_probe(struct pci_dev *pdev,
|
||||
const struct pci_device_id *ent)
|
||||
{
|
||||
#ifdef CONFIG_PCI
|
||||
struct mxser_board *brd;
|
||||
unsigned int i, j;
|
||||
unsigned long ioaddress;
|
||||
|
|
@ -2673,14 +2404,10 @@ err_dis:
|
|||
pci_disable_device(pdev);
|
||||
err:
|
||||
return retval;
|
||||
#else
|
||||
return -ENODEV;
|
||||
#endif
|
||||
}
|
||||
|
||||
static void mxser_remove(struct pci_dev *pdev)
|
||||
{
|
||||
#ifdef CONFIG_PCI
|
||||
struct mxser_board *brd = pci_get_drvdata(pdev);
|
||||
|
||||
mxser_board_remove(brd);
|
||||
|
|
@ -2689,7 +2416,6 @@ static void mxser_remove(struct pci_dev *pdev)
|
|||
pci_release_region(pdev, 3);
|
||||
pci_disable_device(pdev);
|
||||
brd->info = NULL;
|
||||
#endif
|
||||
}
|
||||
|
||||
static struct pci_driver mxser_driver = {
|
||||
|
|
@ -2701,9 +2427,6 @@ static struct pci_driver mxser_driver = {
|
|||
|
||||
static int __init mxser_module_init(void)
|
||||
{
|
||||
struct mxser_board *brd;
|
||||
struct device *tty_dev;
|
||||
unsigned int b, i, m;
|
||||
int retval;
|
||||
|
||||
mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
|
||||
|
|
@ -2731,57 +2454,10 @@ static int __init mxser_module_init(void)
|
|||
goto err_put;
|
||||
}
|
||||
|
||||
/* Start finding ISA boards here */
|
||||
for (m = 0, b = 0; b < MXSER_BOARDS; b++) {
|
||||
if (!ioaddr[b])
|
||||
continue;
|
||||
|
||||
brd = &mxser_boards[m];
|
||||
retval = mxser_get_ISA_conf(ioaddr[b], brd);
|
||||
if (retval <= 0) {
|
||||
brd->info = NULL;
|
||||
continue;
|
||||
}
|
||||
|
||||
printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n",
|
||||
brd->info->name, ioaddr[b]);
|
||||
|
||||
/* mxser_initbrd will hook ISR. */
|
||||
if (mxser_initbrd(brd) < 0) {
|
||||
mxser_release_ISA_res(brd);
|
||||
brd->info = NULL;
|
||||
continue;
|
||||
}
|
||||
|
||||
brd->idx = m * MXSER_PORTS_PER_BOARD;
|
||||
for (i = 0; i < brd->info->nports; i++) {
|
||||
tty_dev = tty_port_register_device(&brd->ports[i].port,
|
||||
mxvar_sdriver, brd->idx + i, NULL);
|
||||
if (IS_ERR(tty_dev)) {
|
||||
for (; i > 0; i--)
|
||||
tty_unregister_device(mxvar_sdriver,
|
||||
brd->idx + i - 1);
|
||||
for (i = 0; i < brd->info->nports; i++)
|
||||
tty_port_destroy(&brd->ports[i].port);
|
||||
free_irq(brd->irq, brd);
|
||||
mxser_release_ISA_res(brd);
|
||||
brd->info = NULL;
|
||||
break;
|
||||
}
|
||||
}
|
||||
if (brd->info == NULL)
|
||||
continue;
|
||||
|
||||
m++;
|
||||
}
|
||||
|
||||
retval = pci_register_driver(&mxser_driver);
|
||||
if (retval) {
|
||||
printk(KERN_ERR "mxser: can't register pci driver\n");
|
||||
if (!m) {
|
||||
retval = -ENODEV;
|
||||
goto err_unr;
|
||||
} /* else: we have some ISA cards under control */
|
||||
goto err_unr;
|
||||
}
|
||||
|
||||
return 0;
|
||||
|
|
@ -2794,19 +2470,9 @@ err_put:
|
|||
|
||||
static void __exit mxser_module_exit(void)
|
||||
{
|
||||
unsigned int i;
|
||||
|
||||
pci_unregister_driver(&mxser_driver);
|
||||
|
||||
for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */
|
||||
if (mxser_boards[i].info != NULL)
|
||||
mxser_board_remove(&mxser_boards[i]);
|
||||
tty_unregister_driver(mxvar_sdriver);
|
||||
put_tty_driver(mxvar_sdriver);
|
||||
|
||||
for (i = 0; i < MXSER_BOARDS; i++)
|
||||
if (mxser_boards[i].info != NULL)
|
||||
mxser_release_ISA_res(&mxser_boards[i]);
|
||||
}
|
||||
|
||||
module_init(mxser_module_init);
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче