i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the CONFIG_I2C_XLP9XX option. Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com> Signed-off-by: Jayachandran C <jchandra@broadcom.com> Reviewed-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit is contained in:
Subhendu Sekhar Behera
Wolfram Sang
Родитель
85e4564ab2
Коммит
2bbd681ba2
|
|
@ -0,0 +1,22 @@
|
|||
Device tree configuration for the I2C controller on the XLP9xx/5xx SoC
|
||||
|
||||
Required properties:
|
||||
- compatible : should be "netlogic,xlp980-i2c"
|
||||
- reg : bus address start and address range size of device
|
||||
- interrupts : interrupt number
|
||||
|
||||
Optional properties:
|
||||
- clock-frequency : frequency of bus clock in Hz
|
||||
Defaults to 100 KHz when the property is not specified
|
||||
|
||||
Example:
|
||||
|
||||
i2c0: i2c@113100 {
|
||||
compatible = "netlogic,xlp980-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0 0x113100 0x100>;
|
||||
clock-frequency = <400000>;
|
||||
interrupts = <30>;
|
||||
interrupt-parent = <&pic>;
|
||||
};
|
||||
|
|
@ -916,6 +916,16 @@ config I2C_XLR
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called i2c-xlr.
|
||||
|
||||
config I2C_XLP9XX
|
||||
tristate "XLP9XX I2C support"
|
||||
depends on CPU_XLP || COMPILE_TEST
|
||||
help
|
||||
This driver enables support for the on-chip I2C interface of
|
||||
the Broadcom XLP9xx/XLP5xx MIPS processors.
|
||||
|
||||
This driver can also be built as a module. If so, the module will
|
||||
be called i2c-xlp9xx.
|
||||
|
||||
config I2C_RCAR
|
||||
tristate "Renesas R-Car I2C Controller"
|
||||
depends on ARCH_SHMOBILE || COMPILE_TEST
|
||||
|
|
|
|||
|
|
@ -89,6 +89,7 @@ obj-$(CONFIG_I2C_WMT) += i2c-wmt.o
|
|||
obj-$(CONFIG_I2C_OCTEON) += i2c-octeon.o
|
||||
obj-$(CONFIG_I2C_XILINX) += i2c-xiic.o
|
||||
obj-$(CONFIG_I2C_XLR) += i2c-xlr.o
|
||||
obj-$(CONFIG_I2C_XLP9XX) += i2c-xlp9xx.o
|
||||
obj-$(CONFIG_I2C_RCAR) += i2c-rcar.o
|
||||
|
||||
# External I2C/SMBus adapter drivers
|
||||
|
|
|
|||
|
|
@ -0,0 +1,445 @@
|
|||
/*
|
||||
* Copyright (c) 2003-2015 Broadcom Corporation
|
||||
*
|
||||
* This file is licensed under the terms of the GNU General Public
|
||||
* License version 2. This program is licensed "as is" without any
|
||||
* warranty of any kind, whether express or implied.
|
||||
*/
|
||||
|
||||
#include <linux/completion.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/platform_device.h>
|
||||
|
||||
#define XLP9XX_I2C_DIV 0x0
|
||||
#define XLP9XX_I2C_CTRL 0x1
|
||||
#define XLP9XX_I2C_CMD 0x2
|
||||
#define XLP9XX_I2C_STATUS 0x3
|
||||
#define XLP9XX_I2C_MTXFIFO 0x4
|
||||
#define XLP9XX_I2C_MRXFIFO 0x5
|
||||
#define XLP9XX_I2C_MFIFOCTRL 0x6
|
||||
#define XLP9XX_I2C_STXFIFO 0x7
|
||||
#define XLP9XX_I2C_SRXFIFO 0x8
|
||||
#define XLP9XX_I2C_SFIFOCTRL 0x9
|
||||
#define XLP9XX_I2C_SLAVEADDR 0xA
|
||||
#define XLP9XX_I2C_OWNADDR 0xB
|
||||
#define XLP9XX_I2C_FIFOWCNT 0xC
|
||||
#define XLP9XX_I2C_INTEN 0xD
|
||||
#define XLP9XX_I2C_INTST 0xE
|
||||
#define XLP9XX_I2C_WAITCNT 0xF
|
||||
#define XLP9XX_I2C_TIMEOUT 0X10
|
||||
#define XLP9XX_I2C_GENCALLADDR 0x11
|
||||
|
||||
#define XLP9XX_I2C_CMD_START BIT(7)
|
||||
#define XLP9XX_I2C_CMD_STOP BIT(6)
|
||||
#define XLP9XX_I2C_CMD_READ BIT(5)
|
||||
#define XLP9XX_I2C_CMD_WRITE BIT(4)
|
||||
#define XLP9XX_I2C_CMD_ACK BIT(3)
|
||||
|
||||
#define XLP9XX_I2C_CTRL_MCTLEN_SHIFT 16
|
||||
#define XLP9XX_I2C_CTRL_MCTLEN_MASK 0xffff0000
|
||||
#define XLP9XX_I2C_CTRL_RST BIT(8)
|
||||
#define XLP9XX_I2C_CTRL_EN BIT(6)
|
||||
#define XLP9XX_I2C_CTRL_MASTER BIT(4)
|
||||
#define XLP9XX_I2C_CTRL_FIFORD BIT(1)
|
||||
#define XLP9XX_I2C_CTRL_ADDMODE BIT(0)
|
||||
|
||||
#define XLP9XX_I2C_INTEN_NACKADDR BIT(25)
|
||||
#define XLP9XX_I2C_INTEN_SADDR BIT(13)
|
||||
#define XLP9XX_I2C_INTEN_DATADONE BIT(12)
|
||||
#define XLP9XX_I2C_INTEN_ARLOST BIT(11)
|
||||
#define XLP9XX_I2C_INTEN_MFIFOFULL BIT(4)
|
||||
#define XLP9XX_I2C_INTEN_MFIFOEMTY BIT(3)
|
||||
#define XLP9XX_I2C_INTEN_MFIFOHI BIT(2)
|
||||
#define XLP9XX_I2C_INTEN_BUSERR BIT(0)
|
||||
|
||||
#define XLP9XX_I2C_MFIFOCTRL_HITH_SHIFT 8
|
||||
#define XLP9XX_I2C_MFIFOCTRL_LOTH_SHIFT 0
|
||||
#define XLP9XX_I2C_MFIFOCTRL_RST BIT(16)
|
||||
|
||||
#define XLP9XX_I2C_SLAVEADDR_RW BIT(0)
|
||||
#define XLP9XX_I2C_SLAVEADDR_ADDR_SHIFT 1
|
||||
|
||||
#define XLP9XX_I2C_IP_CLK_FREQ 133000000UL
|
||||
#define XLP9XX_I2C_DEFAULT_FREQ 100000
|
||||
#define XLP9XX_I2C_HIGH_FREQ 400000
|
||||
#define XLP9XX_I2C_FIFO_SIZE 0x80U
|
||||
#define XLP9XX_I2C_TIMEOUT_MS 1000
|
||||
|
||||
#define XLP9XX_I2C_FIFO_WCNT_MASK 0xff
|
||||
#define XLP9XX_I2C_STATUS_ERRMASK (XLP9XX_I2C_INTEN_ARLOST | \
|
||||
XLP9XX_I2C_INTEN_NACKADDR | XLP9XX_I2C_INTEN_BUSERR)
|
||||
|
||||
struct xlp9xx_i2c_dev {
|
||||
struct device *dev;
|
||||
struct i2c_adapter adapter;
|
||||
struct completion msg_complete;
|
||||
int irq;
|
||||
bool msg_read;
|
||||
u32 __iomem *base;
|
||||
u32 msg_buf_remaining;
|
||||
u32 msg_len;
|
||||
u32 clk_hz;
|
||||
u32 msg_err;
|
||||
u8 *msg_buf;
|
||||
};
|
||||
|
||||
static inline void xlp9xx_write_i2c_reg(struct xlp9xx_i2c_dev *priv,
|
||||
unsigned long reg, u32 val)
|
||||
{
|
||||
writel(val, priv->base + reg);
|
||||
}
|
||||
|
||||
static inline u32 xlp9xx_read_i2c_reg(struct xlp9xx_i2c_dev *priv,
|
||||
unsigned long reg)
|
||||
{
|
||||
return readl(priv->base + reg);
|
||||
}
|
||||
|
||||
static void xlp9xx_i2c_mask_irq(struct xlp9xx_i2c_dev *priv, u32 mask)
|
||||
{
|
||||
u32 inten;
|
||||
|
||||
inten = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTEN) & ~mask;
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, inten);
|
||||
}
|
||||
|
||||
static void xlp9xx_i2c_unmask_irq(struct xlp9xx_i2c_dev *priv, u32 mask)
|
||||
{
|
||||
u32 inten;
|
||||
|
||||
inten = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTEN) | mask;
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, inten);
|
||||
}
|
||||
|
||||
static void xlp9xx_i2c_update_rx_fifo_thres(struct xlp9xx_i2c_dev *priv)
|
||||
{
|
||||
u32 thres;
|
||||
|
||||
thres = min(priv->msg_buf_remaining, XLP9XX_I2C_FIFO_SIZE);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MFIFOCTRL,
|
||||
thres << XLP9XX_I2C_MFIFOCTRL_HITH_SHIFT);
|
||||
}
|
||||
|
||||
static void xlp9xx_i2c_fill_tx_fifo(struct xlp9xx_i2c_dev *priv)
|
||||
{
|
||||
u32 len, i;
|
||||
u8 *buf = priv->msg_buf;
|
||||
|
||||
len = min(priv->msg_buf_remaining, XLP9XX_I2C_FIFO_SIZE);
|
||||
for (i = 0; i < len; i++)
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MTXFIFO, buf[i]);
|
||||
priv->msg_buf_remaining -= len;
|
||||
priv->msg_buf += len;
|
||||
}
|
||||
|
||||
static void xlp9xx_i2c_drain_rx_fifo(struct xlp9xx_i2c_dev *priv)
|
||||
{
|
||||
u32 len, i;
|
||||
u8 *buf = priv->msg_buf;
|
||||
|
||||
len = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_FIFOWCNT) &
|
||||
XLP9XX_I2C_FIFO_WCNT_MASK;
|
||||
len = min(priv->msg_buf_remaining, len);
|
||||
for (i = 0; i < len; i++, buf++)
|
||||
*buf = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_MRXFIFO);
|
||||
|
||||
priv->msg_buf_remaining -= len;
|
||||
priv->msg_buf = buf;
|
||||
|
||||
if (priv->msg_buf_remaining)
|
||||
xlp9xx_i2c_update_rx_fifo_thres(priv);
|
||||
}
|
||||
|
||||
static irqreturn_t xlp9xx_i2c_isr(int irq, void *dev_id)
|
||||
{
|
||||
struct xlp9xx_i2c_dev *priv = dev_id;
|
||||
u32 status;
|
||||
|
||||
status = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTST);
|
||||
if (status == 0)
|
||||
return IRQ_NONE;
|
||||
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTST, status);
|
||||
if (status & XLP9XX_I2C_STATUS_ERRMASK) {
|
||||
priv->msg_err = status;
|
||||
goto xfer_done;
|
||||
}
|
||||
|
||||
/* SADDR ACK for SMBUS_QUICK */
|
||||
if ((status & XLP9XX_I2C_INTEN_SADDR) && (priv->msg_len == 0))
|
||||
goto xfer_done;
|
||||
|
||||
if (!priv->msg_read) {
|
||||
if (status & XLP9XX_I2C_INTEN_MFIFOEMTY) {
|
||||
/* TX FIFO got empty, fill it up again */
|
||||
if (priv->msg_buf_remaining)
|
||||
xlp9xx_i2c_fill_tx_fifo(priv);
|
||||
else
|
||||
xlp9xx_i2c_mask_irq(priv,
|
||||
XLP9XX_I2C_INTEN_MFIFOEMTY);
|
||||
}
|
||||
} else {
|
||||
if (status & (XLP9XX_I2C_INTEN_DATADONE |
|
||||
XLP9XX_I2C_INTEN_MFIFOHI)) {
|
||||
/* data is in FIFO, read it */
|
||||
if (priv->msg_buf_remaining)
|
||||
xlp9xx_i2c_drain_rx_fifo(priv);
|
||||
}
|
||||
}
|
||||
|
||||
/* Transfer complete */
|
||||
if (status & XLP9XX_I2C_INTEN_DATADONE)
|
||||
goto xfer_done;
|
||||
|
||||
return IRQ_HANDLED;
|
||||
|
||||
xfer_done:
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0);
|
||||
complete(&priv->msg_complete);
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int xlp9xx_i2c_init(struct xlp9xx_i2c_dev *priv)
|
||||
{
|
||||
u32 prescale;
|
||||
|
||||
/*
|
||||
* The controller uses 5 * SCL clock internally.
|
||||
* So prescale value should be divided by 5.
|
||||
*/
|
||||
prescale = DIV_ROUND_UP(XLP9XX_I2C_IP_CLK_FREQ, priv->clk_hz);
|
||||
prescale = ((prescale - 8) / 5) - 1;
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, XLP9XX_I2C_CTRL_RST);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, XLP9XX_I2C_CTRL_EN |
|
||||
XLP9XX_I2C_CTRL_MASTER);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_DIV, prescale);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int xlp9xx_i2c_xfer_msg(struct xlp9xx_i2c_dev *priv, struct i2c_msg *msg,
|
||||
int last_msg)
|
||||
{
|
||||
unsigned long timeleft;
|
||||
u32 intr_mask, cmd, val;
|
||||
|
||||
priv->msg_buf = msg->buf;
|
||||
priv->msg_buf_remaining = priv->msg_len = msg->len;
|
||||
priv->msg_err = 0;
|
||||
priv->msg_read = (msg->flags & I2C_M_RD);
|
||||
reinit_completion(&priv->msg_complete);
|
||||
|
||||
/* Reset FIFO */
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MFIFOCTRL,
|
||||
XLP9XX_I2C_MFIFOCTRL_RST);
|
||||
|
||||
/* set FIFO threshold if reading */
|
||||
if (priv->msg_read)
|
||||
xlp9xx_i2c_update_rx_fifo_thres(priv);
|
||||
|
||||
/* set slave addr */
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_SLAVEADDR,
|
||||
(msg->addr << XLP9XX_I2C_SLAVEADDR_ADDR_SHIFT) |
|
||||
(priv->msg_read ? XLP9XX_I2C_SLAVEADDR_RW : 0));
|
||||
|
||||
/* Build control word for transfer */
|
||||
val = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_CTRL);
|
||||
if (!priv->msg_read)
|
||||
val &= ~XLP9XX_I2C_CTRL_FIFORD;
|
||||
else
|
||||
val |= XLP9XX_I2C_CTRL_FIFORD; /* read */
|
||||
|
||||
if (msg->flags & I2C_M_TEN)
|
||||
val |= XLP9XX_I2C_CTRL_ADDMODE; /* 10-bit address mode*/
|
||||
else
|
||||
val &= ~XLP9XX_I2C_CTRL_ADDMODE;
|
||||
|
||||
/* set data length to be transferred */
|
||||
val = (val & ~XLP9XX_I2C_CTRL_MCTLEN_MASK) |
|
||||
(msg->len << XLP9XX_I2C_CTRL_MCTLEN_SHIFT);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, val);
|
||||
|
||||
/* fill fifo during tx */
|
||||
if (!priv->msg_read)
|
||||
xlp9xx_i2c_fill_tx_fifo(priv);
|
||||
|
||||
/* set interrupt mask */
|
||||
intr_mask = (XLP9XX_I2C_INTEN_ARLOST | XLP9XX_I2C_INTEN_BUSERR |
|
||||
XLP9XX_I2C_INTEN_NACKADDR | XLP9XX_I2C_INTEN_DATADONE);
|
||||
|
||||
if (priv->msg_read) {
|
||||
intr_mask |= XLP9XX_I2C_INTEN_MFIFOHI;
|
||||
if (msg->len == 0)
|
||||
intr_mask |= XLP9XX_I2C_INTEN_SADDR;
|
||||
} else {
|
||||
if (msg->len == 0)
|
||||
intr_mask |= XLP9XX_I2C_INTEN_SADDR;
|
||||
else
|
||||
intr_mask |= XLP9XX_I2C_INTEN_MFIFOEMTY;
|
||||
}
|
||||
xlp9xx_i2c_unmask_irq(priv, intr_mask);
|
||||
|
||||
/* set cmd reg */
|
||||
cmd = XLP9XX_I2C_CMD_START;
|
||||
cmd |= (priv->msg_read ? XLP9XX_I2C_CMD_READ : XLP9XX_I2C_CMD_WRITE);
|
||||
if (last_msg)
|
||||
cmd |= XLP9XX_I2C_CMD_STOP;
|
||||
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CMD, cmd);
|
||||
|
||||
timeleft = msecs_to_jiffies(XLP9XX_I2C_TIMEOUT_MS);
|
||||
timeleft = wait_for_completion_timeout(&priv->msg_complete, timeleft);
|
||||
|
||||
if (priv->msg_err) {
|
||||
dev_dbg(priv->dev, "transfer error %x!\n", priv->msg_err);
|
||||
if (priv->msg_err & XLP9XX_I2C_INTEN_BUSERR)
|
||||
xlp9xx_i2c_init(priv);
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
if (timeleft == 0) {
|
||||
dev_dbg(priv->dev, "i2c transfer timed out!\n");
|
||||
xlp9xx_i2c_init(priv);
|
||||
return -ETIMEDOUT;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int xlp9xx_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
|
||||
int num)
|
||||
{
|
||||
int i, ret;
|
||||
struct xlp9xx_i2c_dev *priv = i2c_get_adapdata(adap);
|
||||
|
||||
for (i = 0; i < num; i++) {
|
||||
ret = xlp9xx_i2c_xfer_msg(priv, &msgs[i], i == num - 1);
|
||||
if (ret != 0)
|
||||
return ret;
|
||||
}
|
||||
|
||||
return num;
|
||||
}
|
||||
|
||||
static u32 xlp9xx_i2c_functionality(struct i2c_adapter *adapter)
|
||||
{
|
||||
return I2C_FUNC_SMBUS_EMUL | I2C_FUNC_I2C |
|
||||
I2C_FUNC_10BIT_ADDR;
|
||||
}
|
||||
|
||||
static struct i2c_algorithm xlp9xx_i2c_algo = {
|
||||
.master_xfer = xlp9xx_i2c_xfer,
|
||||
.functionality = xlp9xx_i2c_functionality,
|
||||
};
|
||||
|
||||
static int xlp9xx_i2c_get_frequency(struct platform_device *pdev,
|
||||
struct xlp9xx_i2c_dev *priv)
|
||||
{
|
||||
struct device_node *np = pdev->dev.of_node;
|
||||
u32 freq;
|
||||
int err;
|
||||
|
||||
err = of_property_read_u32(np, "clock-frequency", &freq);
|
||||
if (err) {
|
||||
freq = XLP9XX_I2C_DEFAULT_FREQ;
|
||||
dev_dbg(&pdev->dev, "using default frequency %u\n", freq);
|
||||
} else if (freq == 0 || freq > XLP9XX_I2C_HIGH_FREQ) {
|
||||
dev_warn(&pdev->dev, "invalid frequency %u, using default\n",
|
||||
freq);
|
||||
freq = XLP9XX_I2C_DEFAULT_FREQ;
|
||||
}
|
||||
priv->clk_hz = freq;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int xlp9xx_i2c_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct xlp9xx_i2c_dev *priv;
|
||||
struct resource *res;
|
||||
int err = 0;
|
||||
|
||||
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
|
||||
if (!priv)
|
||||
return -ENOMEM;
|
||||
|
||||
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
priv->base = devm_ioremap_resource(&pdev->dev, res);
|
||||
if (IS_ERR(priv->base))
|
||||
return PTR_ERR(priv->base);
|
||||
|
||||
priv->irq = platform_get_irq(pdev, 0);
|
||||
if (priv->irq <= 0) {
|
||||
dev_err(&pdev->dev, "invalid irq!\n");
|
||||
return priv->irq;
|
||||
}
|
||||
|
||||
xlp9xx_i2c_get_frequency(pdev, priv);
|
||||
xlp9xx_i2c_init(priv);
|
||||
|
||||
err = devm_request_irq(&pdev->dev, priv->irq, xlp9xx_i2c_isr, 0,
|
||||
pdev->name, priv);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "IRQ request failed!\n");
|
||||
return err;
|
||||
}
|
||||
|
||||
init_completion(&priv->msg_complete);
|
||||
priv->adapter.dev.parent = &pdev->dev;
|
||||
priv->adapter.algo = &xlp9xx_i2c_algo;
|
||||
priv->adapter.dev.of_node = pdev->dev.of_node;
|
||||
priv->dev = &pdev->dev;
|
||||
|
||||
snprintf(priv->adapter.name, sizeof(priv->adapter.name), "xlp9xx-i2c");
|
||||
i2c_set_adapdata(&priv->adapter, priv);
|
||||
|
||||
err = i2c_add_adapter(&priv->adapter);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "failed to add I2C adapter!\n");
|
||||
return err;
|
||||
}
|
||||
|
||||
platform_set_drvdata(pdev, priv);
|
||||
dev_dbg(&pdev->dev, "I2C bus:%d added\n", priv->adapter.nr);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int xlp9xx_i2c_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct xlp9xx_i2c_dev *priv;
|
||||
|
||||
priv = platform_get_drvdata(pdev);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0);
|
||||
synchronize_irq(priv->irq);
|
||||
i2c_del_adapter(&priv->adapter);
|
||||
xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, 0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct of_device_id xlp9xx_i2c_of_match[] = {
|
||||
{ .compatible = "netlogic,xlp980-i2c", },
|
||||
{ /* sentinel */ },
|
||||
};
|
||||
|
||||
static struct platform_driver xlp9xx_i2c_driver = {
|
||||
.probe = xlp9xx_i2c_probe,
|
||||
.remove = xlp9xx_i2c_remove,
|
||||
.driver = {
|
||||
.name = "xlp9xx-i2c",
|
||||
.of_match_table = xlp9xx_i2c_of_match,
|
||||
},
|
||||
};
|
||||
|
||||
module_platform_driver(xlp9xx_i2c_driver);
|
||||
|
||||
MODULE_AUTHOR("Subhendu Sekhar Behera <sbehera@broadcom.com>");
|
||||
MODULE_DESCRIPTION("XLP9XX/5XX I2C Bus Controller Driver");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
Загрузка…
Ссылка в новой задаче