From 2bbd681ba2bfa0f3805fb541b0840b96893c5727 Mon Sep 17 00:00:00 2001 From: Subhendu Sekhar Behera Date: Wed, 18 Mar 2015 17:20:29 +0530 Subject: [PATCH] i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the CONFIG_I2C_XLP9XX option. Signed-off-by: Subhendu Sekhar Behera Signed-off-by: Jayachandran C Reviewed-by: Ray Jui Signed-off-by: Wolfram Sang --- .../devicetree/bindings/i2c/i2c-xlp9xx.txt | 22 + drivers/i2c/busses/Kconfig | 10 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-xlp9xx.c | 445 ++++++++++++++++++ 4 files changed, 478 insertions(+) create mode 100644 Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt create mode 100644 drivers/i2c/busses/i2c-xlp9xx.c diff --git a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt new file mode 100644 index 000000000000..f818ef507ab7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt @@ -0,0 +1,22 @@ +Device tree configuration for the I2C controller on the XLP9xx/5xx SoC + +Required properties: +- compatible : should be "netlogic,xlp980-i2c" +- reg : bus address start and address range size of device +- interrupts : interrupt number + +Optional properties: +- clock-frequency : frequency of bus clock in Hz + Defaults to 100 KHz when the property is not specified + +Example: + +i2c0: i2c@113100 { + compatible = "netlogic,xlp980-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x113100 0x100>; + clock-frequency = <400000>; + interrupts = <30>; + interrupt-parent = <&pic>; +}; diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 0b0ca7dd5d1f..2255af23b9c7 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -916,6 +916,16 @@ config I2C_XLR This driver can also be built as a module. If so, the module will be called i2c-xlr. +config I2C_XLP9XX + tristate "XLP9XX I2C support" + depends on CPU_XLP || COMPILE_TEST + help + This driver enables support for the on-chip I2C interface of + the Broadcom XLP9xx/XLP5xx MIPS processors. + + This driver can also be built as a module. If so, the module will + be called i2c-xlp9xx. + config I2C_RCAR tristate "Renesas R-Car I2C Controller" depends on ARCH_SHMOBILE || COMPILE_TEST diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index ab6a0a67aca1..cdf941da91c6 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -89,6 +89,7 @@ obj-$(CONFIG_I2C_WMT) += i2c-wmt.o obj-$(CONFIG_I2C_OCTEON) += i2c-octeon.o obj-$(CONFIG_I2C_XILINX) += i2c-xiic.o obj-$(CONFIG_I2C_XLR) += i2c-xlr.o +obj-$(CONFIG_I2C_XLP9XX) += i2c-xlp9xx.o obj-$(CONFIG_I2C_RCAR) += i2c-rcar.o # External I2C/SMBus adapter drivers diff --git a/drivers/i2c/busses/i2c-xlp9xx.c b/drivers/i2c/busses/i2c-xlp9xx.c new file mode 100644 index 000000000000..c941418f06f5 --- /dev/null +++ b/drivers/i2c/busses/i2c-xlp9xx.c @@ -0,0 +1,445 @@ +/* + * Copyright (c) 2003-2015 Broadcom Corporation + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define XLP9XX_I2C_DIV 0x0 +#define XLP9XX_I2C_CTRL 0x1 +#define XLP9XX_I2C_CMD 0x2 +#define XLP9XX_I2C_STATUS 0x3 +#define XLP9XX_I2C_MTXFIFO 0x4 +#define XLP9XX_I2C_MRXFIFO 0x5 +#define XLP9XX_I2C_MFIFOCTRL 0x6 +#define XLP9XX_I2C_STXFIFO 0x7 +#define XLP9XX_I2C_SRXFIFO 0x8 +#define XLP9XX_I2C_SFIFOCTRL 0x9 +#define XLP9XX_I2C_SLAVEADDR 0xA +#define XLP9XX_I2C_OWNADDR 0xB +#define XLP9XX_I2C_FIFOWCNT 0xC +#define XLP9XX_I2C_INTEN 0xD +#define XLP9XX_I2C_INTST 0xE +#define XLP9XX_I2C_WAITCNT 0xF +#define XLP9XX_I2C_TIMEOUT 0X10 +#define XLP9XX_I2C_GENCALLADDR 0x11 + +#define XLP9XX_I2C_CMD_START BIT(7) +#define XLP9XX_I2C_CMD_STOP BIT(6) +#define XLP9XX_I2C_CMD_READ BIT(5) +#define XLP9XX_I2C_CMD_WRITE BIT(4) +#define XLP9XX_I2C_CMD_ACK BIT(3) + +#define XLP9XX_I2C_CTRL_MCTLEN_SHIFT 16 +#define XLP9XX_I2C_CTRL_MCTLEN_MASK 0xffff0000 +#define XLP9XX_I2C_CTRL_RST BIT(8) +#define XLP9XX_I2C_CTRL_EN BIT(6) +#define XLP9XX_I2C_CTRL_MASTER BIT(4) +#define XLP9XX_I2C_CTRL_FIFORD BIT(1) +#define XLP9XX_I2C_CTRL_ADDMODE BIT(0) + +#define XLP9XX_I2C_INTEN_NACKADDR BIT(25) +#define XLP9XX_I2C_INTEN_SADDR BIT(13) +#define XLP9XX_I2C_INTEN_DATADONE BIT(12) +#define XLP9XX_I2C_INTEN_ARLOST BIT(11) +#define XLP9XX_I2C_INTEN_MFIFOFULL BIT(4) +#define XLP9XX_I2C_INTEN_MFIFOEMTY BIT(3) +#define XLP9XX_I2C_INTEN_MFIFOHI BIT(2) +#define XLP9XX_I2C_INTEN_BUSERR BIT(0) + +#define XLP9XX_I2C_MFIFOCTRL_HITH_SHIFT 8 +#define XLP9XX_I2C_MFIFOCTRL_LOTH_SHIFT 0 +#define XLP9XX_I2C_MFIFOCTRL_RST BIT(16) + +#define XLP9XX_I2C_SLAVEADDR_RW BIT(0) +#define XLP9XX_I2C_SLAVEADDR_ADDR_SHIFT 1 + +#define XLP9XX_I2C_IP_CLK_FREQ 133000000UL +#define XLP9XX_I2C_DEFAULT_FREQ 100000 +#define XLP9XX_I2C_HIGH_FREQ 400000 +#define XLP9XX_I2C_FIFO_SIZE 0x80U +#define XLP9XX_I2C_TIMEOUT_MS 1000 + +#define XLP9XX_I2C_FIFO_WCNT_MASK 0xff +#define XLP9XX_I2C_STATUS_ERRMASK (XLP9XX_I2C_INTEN_ARLOST | \ + XLP9XX_I2C_INTEN_NACKADDR | XLP9XX_I2C_INTEN_BUSERR) + +struct xlp9xx_i2c_dev { + struct device *dev; + struct i2c_adapter adapter; + struct completion msg_complete; + int irq; + bool msg_read; + u32 __iomem *base; + u32 msg_buf_remaining; + u32 msg_len; + u32 clk_hz; + u32 msg_err; + u8 *msg_buf; +}; + +static inline void xlp9xx_write_i2c_reg(struct xlp9xx_i2c_dev *priv, + unsigned long reg, u32 val) +{ + writel(val, priv->base + reg); +} + +static inline u32 xlp9xx_read_i2c_reg(struct xlp9xx_i2c_dev *priv, + unsigned long reg) +{ + return readl(priv->base + reg); +} + +static void xlp9xx_i2c_mask_irq(struct xlp9xx_i2c_dev *priv, u32 mask) +{ + u32 inten; + + inten = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTEN) & ~mask; + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, inten); +} + +static void xlp9xx_i2c_unmask_irq(struct xlp9xx_i2c_dev *priv, u32 mask) +{ + u32 inten; + + inten = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTEN) | mask; + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, inten); +} + +static void xlp9xx_i2c_update_rx_fifo_thres(struct xlp9xx_i2c_dev *priv) +{ + u32 thres; + + thres = min(priv->msg_buf_remaining, XLP9XX_I2C_FIFO_SIZE); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MFIFOCTRL, + thres << XLP9XX_I2C_MFIFOCTRL_HITH_SHIFT); +} + +static void xlp9xx_i2c_fill_tx_fifo(struct xlp9xx_i2c_dev *priv) +{ + u32 len, i; + u8 *buf = priv->msg_buf; + + len = min(priv->msg_buf_remaining, XLP9XX_I2C_FIFO_SIZE); + for (i = 0; i < len; i++) + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MTXFIFO, buf[i]); + priv->msg_buf_remaining -= len; + priv->msg_buf += len; +} + +static void xlp9xx_i2c_drain_rx_fifo(struct xlp9xx_i2c_dev *priv) +{ + u32 len, i; + u8 *buf = priv->msg_buf; + + len = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_FIFOWCNT) & + XLP9XX_I2C_FIFO_WCNT_MASK; + len = min(priv->msg_buf_remaining, len); + for (i = 0; i < len; i++, buf++) + *buf = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_MRXFIFO); + + priv->msg_buf_remaining -= len; + priv->msg_buf = buf; + + if (priv->msg_buf_remaining) + xlp9xx_i2c_update_rx_fifo_thres(priv); +} + +static irqreturn_t xlp9xx_i2c_isr(int irq, void *dev_id) +{ + struct xlp9xx_i2c_dev *priv = dev_id; + u32 status; + + status = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_INTST); + if (status == 0) + return IRQ_NONE; + + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTST, status); + if (status & XLP9XX_I2C_STATUS_ERRMASK) { + priv->msg_err = status; + goto xfer_done; + } + + /* SADDR ACK for SMBUS_QUICK */ + if ((status & XLP9XX_I2C_INTEN_SADDR) && (priv->msg_len == 0)) + goto xfer_done; + + if (!priv->msg_read) { + if (status & XLP9XX_I2C_INTEN_MFIFOEMTY) { + /* TX FIFO got empty, fill it up again */ + if (priv->msg_buf_remaining) + xlp9xx_i2c_fill_tx_fifo(priv); + else + xlp9xx_i2c_mask_irq(priv, + XLP9XX_I2C_INTEN_MFIFOEMTY); + } + } else { + if (status & (XLP9XX_I2C_INTEN_DATADONE | + XLP9XX_I2C_INTEN_MFIFOHI)) { + /* data is in FIFO, read it */ + if (priv->msg_buf_remaining) + xlp9xx_i2c_drain_rx_fifo(priv); + } + } + + /* Transfer complete */ + if (status & XLP9XX_I2C_INTEN_DATADONE) + goto xfer_done; + + return IRQ_HANDLED; + +xfer_done: + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0); + complete(&priv->msg_complete); + return IRQ_HANDLED; +} + +static int xlp9xx_i2c_init(struct xlp9xx_i2c_dev *priv) +{ + u32 prescale; + + /* + * The controller uses 5 * SCL clock internally. + * So prescale value should be divided by 5. + */ + prescale = DIV_ROUND_UP(XLP9XX_I2C_IP_CLK_FREQ, priv->clk_hz); + prescale = ((prescale - 8) / 5) - 1; + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, XLP9XX_I2C_CTRL_RST); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, XLP9XX_I2C_CTRL_EN | + XLP9XX_I2C_CTRL_MASTER); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_DIV, prescale); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0); + + return 0; +} + +static int xlp9xx_i2c_xfer_msg(struct xlp9xx_i2c_dev *priv, struct i2c_msg *msg, + int last_msg) +{ + unsigned long timeleft; + u32 intr_mask, cmd, val; + + priv->msg_buf = msg->buf; + priv->msg_buf_remaining = priv->msg_len = msg->len; + priv->msg_err = 0; + priv->msg_read = (msg->flags & I2C_M_RD); + reinit_completion(&priv->msg_complete); + + /* Reset FIFO */ + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_MFIFOCTRL, + XLP9XX_I2C_MFIFOCTRL_RST); + + /* set FIFO threshold if reading */ + if (priv->msg_read) + xlp9xx_i2c_update_rx_fifo_thres(priv); + + /* set slave addr */ + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_SLAVEADDR, + (msg->addr << XLP9XX_I2C_SLAVEADDR_ADDR_SHIFT) | + (priv->msg_read ? XLP9XX_I2C_SLAVEADDR_RW : 0)); + + /* Build control word for transfer */ + val = xlp9xx_read_i2c_reg(priv, XLP9XX_I2C_CTRL); + if (!priv->msg_read) + val &= ~XLP9XX_I2C_CTRL_FIFORD; + else + val |= XLP9XX_I2C_CTRL_FIFORD; /* read */ + + if (msg->flags & I2C_M_TEN) + val |= XLP9XX_I2C_CTRL_ADDMODE; /* 10-bit address mode*/ + else + val &= ~XLP9XX_I2C_CTRL_ADDMODE; + + /* set data length to be transferred */ + val = (val & ~XLP9XX_I2C_CTRL_MCTLEN_MASK) | + (msg->len << XLP9XX_I2C_CTRL_MCTLEN_SHIFT); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, val); + + /* fill fifo during tx */ + if (!priv->msg_read) + xlp9xx_i2c_fill_tx_fifo(priv); + + /* set interrupt mask */ + intr_mask = (XLP9XX_I2C_INTEN_ARLOST | XLP9XX_I2C_INTEN_BUSERR | + XLP9XX_I2C_INTEN_NACKADDR | XLP9XX_I2C_INTEN_DATADONE); + + if (priv->msg_read) { + intr_mask |= XLP9XX_I2C_INTEN_MFIFOHI; + if (msg->len == 0) + intr_mask |= XLP9XX_I2C_INTEN_SADDR; + } else { + if (msg->len == 0) + intr_mask |= XLP9XX_I2C_INTEN_SADDR; + else + intr_mask |= XLP9XX_I2C_INTEN_MFIFOEMTY; + } + xlp9xx_i2c_unmask_irq(priv, intr_mask); + + /* set cmd reg */ + cmd = XLP9XX_I2C_CMD_START; + cmd |= (priv->msg_read ? XLP9XX_I2C_CMD_READ : XLP9XX_I2C_CMD_WRITE); + if (last_msg) + cmd |= XLP9XX_I2C_CMD_STOP; + + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CMD, cmd); + + timeleft = msecs_to_jiffies(XLP9XX_I2C_TIMEOUT_MS); + timeleft = wait_for_completion_timeout(&priv->msg_complete, timeleft); + + if (priv->msg_err) { + dev_dbg(priv->dev, "transfer error %x!\n", priv->msg_err); + if (priv->msg_err & XLP9XX_I2C_INTEN_BUSERR) + xlp9xx_i2c_init(priv); + return -EIO; + } + + if (timeleft == 0) { + dev_dbg(priv->dev, "i2c transfer timed out!\n"); + xlp9xx_i2c_init(priv); + return -ETIMEDOUT; + } + + return 0; +} + +static int xlp9xx_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, + int num) +{ + int i, ret; + struct xlp9xx_i2c_dev *priv = i2c_get_adapdata(adap); + + for (i = 0; i < num; i++) { + ret = xlp9xx_i2c_xfer_msg(priv, &msgs[i], i == num - 1); + if (ret != 0) + return ret; + } + + return num; +} + +static u32 xlp9xx_i2c_functionality(struct i2c_adapter *adapter) +{ + return I2C_FUNC_SMBUS_EMUL | I2C_FUNC_I2C | + I2C_FUNC_10BIT_ADDR; +} + +static struct i2c_algorithm xlp9xx_i2c_algo = { + .master_xfer = xlp9xx_i2c_xfer, + .functionality = xlp9xx_i2c_functionality, +}; + +static int xlp9xx_i2c_get_frequency(struct platform_device *pdev, + struct xlp9xx_i2c_dev *priv) +{ + struct device_node *np = pdev->dev.of_node; + u32 freq; + int err; + + err = of_property_read_u32(np, "clock-frequency", &freq); + if (err) { + freq = XLP9XX_I2C_DEFAULT_FREQ; + dev_dbg(&pdev->dev, "using default frequency %u\n", freq); + } else if (freq == 0 || freq > XLP9XX_I2C_HIGH_FREQ) { + dev_warn(&pdev->dev, "invalid frequency %u, using default\n", + freq); + freq = XLP9XX_I2C_DEFAULT_FREQ; + } + priv->clk_hz = freq; + + return 0; +} + +static int xlp9xx_i2c_probe(struct platform_device *pdev) +{ + struct xlp9xx_i2c_dev *priv; + struct resource *res; + int err = 0; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->irq = platform_get_irq(pdev, 0); + if (priv->irq <= 0) { + dev_err(&pdev->dev, "invalid irq!\n"); + return priv->irq; + } + + xlp9xx_i2c_get_frequency(pdev, priv); + xlp9xx_i2c_init(priv); + + err = devm_request_irq(&pdev->dev, priv->irq, xlp9xx_i2c_isr, 0, + pdev->name, priv); + if (err) { + dev_err(&pdev->dev, "IRQ request failed!\n"); + return err; + } + + init_completion(&priv->msg_complete); + priv->adapter.dev.parent = &pdev->dev; + priv->adapter.algo = &xlp9xx_i2c_algo; + priv->adapter.dev.of_node = pdev->dev.of_node; + priv->dev = &pdev->dev; + + snprintf(priv->adapter.name, sizeof(priv->adapter.name), "xlp9xx-i2c"); + i2c_set_adapdata(&priv->adapter, priv); + + err = i2c_add_adapter(&priv->adapter); + if (err) { + dev_err(&pdev->dev, "failed to add I2C adapter!\n"); + return err; + } + + platform_set_drvdata(pdev, priv); + dev_dbg(&pdev->dev, "I2C bus:%d added\n", priv->adapter.nr); + + return 0; +} + +static int xlp9xx_i2c_remove(struct platform_device *pdev) +{ + struct xlp9xx_i2c_dev *priv; + + priv = platform_get_drvdata(pdev); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_INTEN, 0); + synchronize_irq(priv->irq); + i2c_del_adapter(&priv->adapter); + xlp9xx_write_i2c_reg(priv, XLP9XX_I2C_CTRL, 0); + + return 0; +} + +static const struct of_device_id xlp9xx_i2c_of_match[] = { + { .compatible = "netlogic,xlp980-i2c", }, + { /* sentinel */ }, +}; + +static struct platform_driver xlp9xx_i2c_driver = { + .probe = xlp9xx_i2c_probe, + .remove = xlp9xx_i2c_remove, + .driver = { + .name = "xlp9xx-i2c", + .of_match_table = xlp9xx_i2c_of_match, + }, +}; + +module_platform_driver(xlp9xx_i2c_driver); + +MODULE_AUTHOR("Subhendu Sekhar Behera "); +MODULE_DESCRIPTION("XLP9XX/5XX I2C Bus Controller Driver"); +MODULE_LICENSE("GPL v2");