[SCSI] aacraid: Dual firmware image support

This patch adds dual flash firmware support for Series 7 and above controllers.

[thenzl: used ssleep(10) instead udelay]
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

drivers/scsi/aacraid/aacraid.h

@@ -12,7 +12,7 @@
  *----------------------------------------------------------------------------*/
 
 #ifndef AAC_DRIVER_BUILD
-# define AAC_DRIVER_BUILD 30000
+# define AAC_DRIVER_BUILD 30200
 # define AAC_DRIVER_BRANCH "-ms"
 #endif
 #define MAXIMUM_NUM_CONTAINERS	32
@@ -1918,6 +1918,10 @@ extern struct aac_common aac_config;
 #define	MONITOR_PANIC			0x00000020
 #define	KERNEL_UP_AND_RUNNING		0x00000080
 #define	KERNEL_PANIC			0x00000100
+#define	FLASH_UPD_PENDING		0x00002000
+#define	FLASH_UPD_SUCCESS		0x00004000
+#define	FLASH_UPD_FAILED		0x00008000
+#define	FWUPD_TIMEOUT			(5 * 60)
 
 /*
  *	Doorbell bit defines

drivers/scsi/aacraid/comminit.c

@@ -214,7 +214,7 @@ int aac_send_shutdown(struct aac_dev * dev)
 	cmd = (struct aac_close *) fib_data(fibctx);
 
 	cmd->command = cpu_to_le32(VM_CloseAll);
-	cmd->cid = cpu_to_le32(0xffffffff);
+	cmd->cid = cpu_to_le32(0xfffffffe);
 
 	status = aac_fib_send(ContainerCommand,
 			  fibctx,

drivers/scsi/aacraid/src.c

@@ -702,6 +702,28 @@ int aac_srcv_init(struct aac_dev *dev)
 	if ((aac_reset_devices || reset_devices) &&
 		!aac_src_restart_adapter(dev, 0))
 		++restart;
+	/*
+	 *	Check to see if flash update is running.
+	 *	Wait for the adapter to be up and running. Wait up to 5 minutes
+	 */
+	status = src_readl(dev, MUnit.OMR);
+	if (status & FLASH_UPD_PENDING) {
+		start = jiffies;
+		do {
+			status = src_readl(dev, MUnit.OMR);
+			if (time_after(jiffies, start+HZ*FWUPD_TIMEOUT)) {
+				printk(KERN_ERR "%s%d: adapter flash update failed.\n",
+					dev->name, instance);
+				goto error_iounmap;
+			}
+		} while (!(status & FLASH_UPD_SUCCESS) &&
+			 !(status & FLASH_UPD_FAILED));
+		/* Delay 10 seconds.
+		 * Because right now FW is doing a soft reset,
+		 * do not read scratch pad register at this time
+		 */
+		ssleep(10);
+	}
 	/*
 	 *	Check to see if the board panic'd while booting.
 	 */
@@ -730,7 +752,9 @@ int aac_srcv_init(struct aac_dev *dev)
 	/*
 	 *	Wait for the adapter to be up and running. Wait up to 3 minutes
 	 */
-	while (!((status = src_readl(dev, MUnit.OMR)) & KERNEL_UP_AND_RUNNING)) {
+	while (!((status = src_readl(dev, MUnit.OMR)) &
+		KERNEL_UP_AND_RUNNING) ||
+		status == 0xffffffff) {
 		if ((restart &&
 		  (status & (KERNEL_PANIC|SELF_TEST_FAILED|MONITOR_PANIC))) ||
 		  time_after(jiffies, start+HZ*startup_timeout)) {