CRIS: avoid using arch links in Kconfig

Improve including of architecture dependent Kconfig files.

- Always include the architecture dependent Kconfig files.
- Wrap architecture dependent Kconfig files inside an appropriate
  "if ETRAX_ARCH_Vxx" block.

This makes it possible to run the configuration even without the arch links,
which are created later in the build process.

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit is contained in:
Jesper Nilsson 2008-02-04 22:30:31 -08:00 коммит произвёл Linus Torvalds
Родитель 7e02dbf724
Коммит 2d33d563b1
5 изменённых файлов: 19 добавлений и 2 удалений

Просмотреть файл

@ -150,6 +150,7 @@ config ETRAX_FLASH_BUSWIDTH
Width in bytes of the Flash bus (1, 2 or 4). Is usually 2. Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
source arch/cris/arch-v10/Kconfig source arch/cris/arch-v10/Kconfig
source arch/cris/arch-v32/Kconfig
endmenu endmenu
@ -157,8 +158,8 @@ source "net/Kconfig"
# bring in ETRAX built-in drivers # bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces" menu "Drivers for built-in interfaces"
# arch/cris/arch is a symlink to correct arch (arch-v10 or arch-v32) source arch/cris/arch-v10/drivers/Kconfig
source arch/cris/arch/drivers/Kconfig source arch/cris/arch-v32/drivers/Kconfig
endmenu endmenu

Просмотреть файл

@ -1,3 +1,5 @@
if ETRAX_ARCH_V10
# ETRAX 100LX v1 has a MMU "feature" requiring a low mapping # ETRAX 100LX v1 has a MMU "feature" requiring a low mapping
config CRIS_LOW_MAP config CRIS_LOW_MAP
bool bool
@ -451,3 +453,5 @@ config ETRAX_POWERBUTTON_BIT
default "25" default "25"
help help
Configure where power button is connected. Configure where power button is connected.
endif

Просмотреть файл

@ -1,3 +1,5 @@
if ETRAX_ARCH_V10
config ETRAX_ETHERNET config ETRAX_ETHERNET
bool "Ethernet support" bool "Ethernet support"
depends on ETRAX_ARCH_V10 depends on ETRAX_ARCH_V10
@ -806,3 +808,5 @@ config ETRAX_DS1302_TRICKLE_CHARGE
1 = 2kohm, 2 = 4kohm, 3 = 4kohm 1 = 2kohm, 2 = 4kohm, 3 = 4kohm
4 = 1 diode, 8 = 2 diodes 4 = 1 diode, 8 = 2 diodes
Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5 Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
endif

Просмотреть файл

@ -1,3 +1,5 @@
if ETRAX_ARCH_V32
config ETRAX_DRAM_VIRTUAL_BASE config ETRAX_DRAM_VIRTUAL_BASE
hex hex
depends on ETRAX_ARCH_V32 depends on ETRAX_ARCH_V32
@ -294,3 +296,5 @@ config ETRAX_DEF_GIO_PE_OUT
help help
Configures the initial data for the general port E bits. Most Configures the initial data for the general port E bits. Most
products should use 00000 here. products should use 00000 here.
endif

Просмотреть файл

@ -1,3 +1,5 @@
if ETRAX_ARCH_V32
config ETRAX_ETHERNET config ETRAX_ETHERNET
bool "Ethernet support" bool "Ethernet support"
depends on ETRAX_ARCH_V32 depends on ETRAX_ARCH_V32
@ -610,3 +612,5 @@ config ETRAX_STREAMCOPROC
help help
This option enables a driver for the stream co-processor This option enables a driver for the stream co-processor
for cryptographic operations. for cryptographic operations.
endif