gpio: rcar: Fine-grained Runtime PM support
Currently gpio modules are runtime-resumed at probe time. This means the gpio module will be active all the time (except during system suspend, if not configured as a wake-up source). While an R-Car Gen2 gpio module retains pins configured for output at the requested level while put in standby mode, gpio register cannot be accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be called from all contexts where gpio register access is needed. Hence move the Runtime PM handling from probe/remove time to gpio request/free time, which is probably the best we can do. On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6 for SD-Card CD & WP, gpio7 for keys and regulators). Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> [Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/] Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
Родитель
47bd38a31a
Коммит
2d65472bcb
|
@ -242,11 +242,24 @@ static void gpio_rcar_config_general_input_output_mode(struct gpio_chip *chip,
|
|||
|
||||
static int gpio_rcar_request(struct gpio_chip *chip, unsigned offset)
|
||||
{
|
||||
return pinctrl_request_gpio(chip->base + offset);
|
||||
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
||||
int error;
|
||||
|
||||
error = pm_runtime_get_sync(&p->pdev->dev);
|
||||
if (error < 0)
|
||||
return error;
|
||||
|
||||
error = pinctrl_request_gpio(chip->base + offset);
|
||||
if (error)
|
||||
pm_runtime_put(&p->pdev->dev);
|
||||
|
||||
return error;
|
||||
}
|
||||
|
||||
static void gpio_rcar_free(struct gpio_chip *chip, unsigned offset)
|
||||
{
|
||||
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
||||
|
||||
pinctrl_free_gpio(chip->base + offset);
|
||||
|
||||
/*
|
||||
|
@ -254,6 +267,8 @@ static void gpio_rcar_free(struct gpio_chip *chip, unsigned offset)
|
|||
* drive the GPIO pin as an output.
|
||||
*/
|
||||
gpio_rcar_config_general_input_output_mode(chip, offset, false);
|
||||
|
||||
pm_runtime_put(&p->pdev->dev);
|
||||
}
|
||||
|
||||
static int gpio_rcar_direction_input(struct gpio_chip *chip, unsigned offset)
|
||||
|
@ -426,7 +441,6 @@ static int gpio_rcar_probe(struct platform_device *pdev)
|
|||
}
|
||||
|
||||
pm_runtime_enable(dev);
|
||||
pm_runtime_get_sync(dev);
|
||||
|
||||
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
|
||||
|
@ -495,7 +509,6 @@ static int gpio_rcar_probe(struct platform_device *pdev)
|
|||
err1:
|
||||
gpiochip_remove(gpio_chip);
|
||||
err0:
|
||||
pm_runtime_put(dev);
|
||||
pm_runtime_disable(dev);
|
||||
return ret;
|
||||
}
|
||||
|
@ -506,7 +519,6 @@ static int gpio_rcar_remove(struct platform_device *pdev)
|
|||
|
||||
gpiochip_remove(&p->gpio_chip);
|
||||
|
||||
pm_runtime_put(&pdev->dev);
|
||||
pm_runtime_disable(&pdev->dev);
|
||||
return 0;
|
||||
}
|
||||
|
|
Загрузка…
Ссылка в новой задаче