From 3265f421887847db9ae2c01a00645e33608556d8 Mon Sep 17 00:00:00 2001 From: Robert Hancock Date: Tue, 25 Jan 2022 10:54:09 -0600 Subject: [PATCH] net: phy: at803x: add fiber support Previously this driver always forced the copper page to be selected, however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page needs to be selected. Set the appropriate mode based on the hardware mode_cfg strap selection. Enable the appropriate interrupt bits to detect fiber-side link up or down events. Update config_aneg and read_status methods to use the appropriate Clause 37 calls when fiber mode is in use. Signed-off-by: Robert Hancock Signed-off-by: David S. Miller --- drivers/net/phy/at803x.c | 76 +++++++++++++++++++++++++++++++++++----- 1 file changed, 67 insertions(+), 9 deletions(-) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 052b2eb9f101..3f3d4c164df4 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -51,6 +51,8 @@ #define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12) #define AT803X_INTR_ENABLE_LINK_FAIL BIT(11) #define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10) +#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8) +#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7) #define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5) #define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1) #define AT803X_INTR_ENABLE_WOL BIT(0) @@ -85,7 +87,17 @@ #define AT803X_DEBUG_DATA 0x1E #define AT803X_MODE_CFG_MASK 0x0F -#define AT803X_MODE_CFG_SGMII 0x01 +#define AT803X_MODE_CFG_BASET_RGMII 0x00 +#define AT803X_MODE_CFG_BASET_SGMII 0x01 +#define AT803X_MODE_CFG_BX1000_RGMII_50OHM 0x02 +#define AT803X_MODE_CFG_BX1000_RGMII_75OHM 0x03 +#define AT803X_MODE_CFG_BX1000_CONV_50OHM 0x04 +#define AT803X_MODE_CFG_BX1000_CONV_75OHM 0x05 +#define AT803X_MODE_CFG_FX100_RGMII_50OHM 0x06 +#define AT803X_MODE_CFG_FX100_CONV_50OHM 0x07 +#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B +#define AT803X_MODE_CFG_FX100_RGMII_75OHM 0x0E +#define AT803X_MODE_CFG_FX100_CONV_75OHM 0x0F #define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/ #define AT803X_PSSR_MR_AN_COMPLETE 0x0200 @@ -283,6 +295,8 @@ struct at803x_priv { u16 clk_25m_mask; u8 smarteee_lpi_tw_1g; u8 smarteee_lpi_tw_100m; + bool is_fiber; + bool is_1000basex; struct regulator_dev *vddio_rdev; struct regulator_dev *vddh_rdev; struct regulator *vddio; @@ -784,7 +798,33 @@ static int at803x_probe(struct phy_device *phydev) return ret; } + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG); + int mode_cfg; + + if (ccr < 0) + goto err; + mode_cfg = ccr & AT803X_MODE_CFG_MASK; + + switch (mode_cfg) { + case AT803X_MODE_CFG_BX1000_RGMII_50OHM: + case AT803X_MODE_CFG_BX1000_RGMII_75OHM: + priv->is_1000basex = true; + fallthrough; + case AT803X_MODE_CFG_FX100_RGMII_50OHM: + case AT803X_MODE_CFG_FX100_RGMII_75OHM: + priv->is_fiber = true; + break; + } + } + return 0; + +err: + if (priv->vddio) + regulator_disable(priv->vddio); + + return ret; } static void at803x_remove(struct phy_device *phydev) @@ -797,6 +837,7 @@ static void at803x_remove(struct phy_device *phydev) static int at803x_get_features(struct phy_device *phydev) { + struct at803x_priv *priv = phydev->priv; int err; err = genphy_read_abilities(phydev); @@ -823,12 +864,13 @@ static int at803x_get_features(struct phy_device *phydev) * As a result of that, ESTATUS_1000_XFULL is set * to 1 even when operating in copper TP mode. * - * Remove this mode from the supported link modes, - * as this driver currently only supports copper - * operation. + * Remove this mode from the supported link modes + * when not operating in 1000BaseX mode. */ - linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, - phydev->supported); + if (!priv->is_1000basex) + linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, + phydev->supported); + return 0; } @@ -892,15 +934,18 @@ static int at8031_pll_config(struct phy_device *phydev) static int at803x_config_init(struct phy_device *phydev) { + struct at803x_priv *priv = phydev->priv; int ret; if (phydev->drv->phy_id == ATH8031_PHY_ID) { /* Some bootloaders leave the fiber page selected. - * Switch to the copper page, as otherwise we read - * the PHY capabilities from the fiber side. + * Switch to the appropriate page (fiber or copper), as otherwise we + * read the PHY capabilities from the wrong page. */ phy_lock_mdio_bus(phydev); - ret = at803x_write_page(phydev, AT803X_PAGE_COPPER); + ret = at803x_write_page(phydev, + priv->is_fiber ? AT803X_PAGE_FIBER : + AT803X_PAGE_COPPER); phy_unlock_mdio_bus(phydev); if (ret) return ret; @@ -959,6 +1004,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev) static int at803x_config_intr(struct phy_device *phydev) { + struct at803x_priv *priv = phydev->priv; int err; int value; @@ -975,6 +1021,10 @@ static int at803x_config_intr(struct phy_device *phydev) value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED; value |= AT803X_INTR_ENABLE_LINK_FAIL; value |= AT803X_INTR_ENABLE_LINK_SUCCESS; + if (priv->is_fiber) { + value |= AT803X_INTR_ENABLE_LINK_FAIL_BX; + value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX; + } err = phy_write(phydev, AT803X_INTR_ENABLE, value); } else { @@ -1107,8 +1157,12 @@ static int at803x_read_specific_status(struct phy_device *phydev) static int at803x_read_status(struct phy_device *phydev) { + struct at803x_priv *priv = phydev->priv; int err, old_link = phydev->link; + if (priv->is_1000basex) + return genphy_c37_read_status(phydev); + /* Update the link, but return if there was an error */ err = genphy_update_link(phydev); if (err) @@ -1162,6 +1216,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl) static int at803x_config_aneg(struct phy_device *phydev) { + struct at803x_priv *priv = phydev->priv; int ret; ret = at803x_config_mdix(phydev, phydev->mdix_ctrl); @@ -1178,6 +1233,9 @@ static int at803x_config_aneg(struct phy_device *phydev) return ret; } + if (priv->is_1000basex) + return genphy_c37_config_aneg(phydev); + /* Do not restart auto-negotiation by setting ret to 0 defautly, * when calling __genphy_config_aneg later. */